Comparative Study of Exhaust Emissions from Diesel and Syngas Powered 3.5 kW Compression Ignition Engine with and without Load

Despite diesel engines being highly efficient, with low fuel consumption and reduced carbon dioxide emissions, they emit relatively high levels of particulate matter and oxides of nitrogen (NOx) due to high exhaust gas temperatures. Engine emissions show the quality and completeness of combustion. This paper aims to present the results of a study comparing exhaust emissions from a diesel and syngas powered engine. Syngas was produced from co-firing coal and biomass in a gasifier then cleaned, cooled and applied as an alternative fuel in an engine operated from 0 - 100% load. Exhaust-emissions were monitored at this load conditions. The exhaust-temperature was measured using thermocouples and the emission gases were analyzed using Testo 350. The emissions were lower and decreased as the engine load increased, except for sulphur dioxide and NOx. The study shows that levels of carbon monoxide, were higher in a range of 46.5 - 80.2%, while carbon dioxide was 3.3 - 18% higher compared to those from diesel. Hydrocarbon emissions were 480 and 1250 ppm for diesel and syngas respectively. The study reveals that the engine operates optimally at higher loads since hydrocarbons and oxides of carbon are low due to complete combustion at higher temperatures. Exhaust gas temperature was higher in the syngas fuel and increased as the engine load increased in the range of 455.83 - 480.03˚C which influenced the formation of NOx. NOx from diesel was found to be higher, ranging from 32.5 - 40.5%, compared to those from syngas with an engine load of 75%. The study observed that relative to diesel, the emissions of sulfur dioxide at 50% engine load were lower in a range of 23.7 - 57.1%. Emissions of hydrocarbons depended on the degree of substitution of diesel and engine load. The study therefore shows that, relative to diesel, emissions decreased when syngas was used with upgraded syngas from Prosporis juliflora presenting as the best alternative followed by Hyphanae compressa, and lastly rice husk. For optimal performance of the syngas fuelled engine, the study reports that the engine should be operated at engine loads above 50% with strategies on NOx emissions considered.

New Leiderman–Khlystov Coefficients for Estimating Engine Full Load Characteristics and Performance

The paper presents a method of calculating the full load engine characteristics based on the Leiderman–Khlystov relation. Because the values of the coefficients of the discussed function available in literature were determined for obsolete engine designs, an attempt was made to update them. To this end, a chassis dynamometer was used where a database of results had been built for a variety of vehicles. Following the data collection, the coefficients for variety of fueling system(six groups: fuel injected gasoline and turbocharged gasoline, spark ignition LPG Ⅰ–Ⅱ and Ⅳ generation, naturally aspirated diesel and turbocharged diesel) were determined. The identification of the coefficients was carried out in Matlab-Simulink indicating the applicability of the said function for most of the engines, yet the recent popularity of turbocharged gasoline engines requires an additional analysis of the possibility of use of a different functional description. The full load engine characteristics is a basis for the vehicle performance characteristics and, further, for modeling of traffic in a variety of aspects of the vehicle operation.

Normalization method for asphalt mixture fatigue equation under different loading frequencies

In order to analyze the effect of different loading frequencies on the fatigue performance for asphalt mixture,the changing law of asphalt mixture strengths with loading speed was revealed by strength tests under different loading speeds.Fatigue equations of asphalt mixtures based on the nominal stress ratio and real stress ratio were established using fatigue tests under different loading frequencies.It was revealed that the strength of the asphalt mixture is affected by the loading speed greatly.It was also discovered that the fatigue equation based on the nominal stress ratio will change with the change of the fatigue loading speed.There is no uniqueness.But the fatigue equation based on the real stress ratio doesn't change with the loading frequency.It has the uniqueness.The results indicate the fatigue equation based on the real stress ratio can realize the normalization of the asphalt mixture fatigue equation under different loading frequencies.It can greatly benefit the analysis of the fatigue characteristics under different vehicle speeds for asphalt pavement.

Recent changing patterns of the Changjiang(Yangtze River) Estuary caused by human activities

To evaluate the controlling factors for coastline change of the Changjiang（Yangtze River） Estuary since 1974,we extracted the mean high tide line from multi-temporal remote sensing images that span from 1974 to 2014 at 2-year intervals.We chose 42 scenes to constrain the changing pattern of the Changjiang Estuary coastline,and implemented GIS technology to analyze the area change of the Changjiang（Yangtze） Subaerial Delta.Runoff,sediment discharge and coastal engineering were withal considered in the analysis of the coastline changes.The coastline has transgressed seaward since 1974,and a part of it presents inter-annual variations.The area of the Changjiang Subaerial Delta increased by 871 km2,with a net accretion rate of 21.8 km2/a.Based on the change of sediment discharge due to the major projects in the Changjiang River Basin,we divided the changing pattern of the coastline into three stages：the slow accretion stage（1974–1986）,the moderate accretion stage（1987–2002）,and the rapid accretion stage（2003–2014）.Liner regression analysis illustrated that there is a significantly positive correlation between the area changes and sediment discharge in the Chongming Eastern Shoal and Jiuduansha.This suggested that sediment load has a fundamental effect on the evolution of the Changjiang Estuary.Construction of Deep Waterway in the North Passage of the Changjiang River（1998–2010） led to a rapid accretion in the Hengsha Eastern Shoal and Jiuduansha by influencing the hydrodynamics in North Passage.Coastal engineering such as reclamation and harbor construction can also change the morphology of the Changjiang Estuary.We defined a contribution rate of area change to assess the impact of reclamation on the evolution of Changjiang Estuary.It turned out that more than 45.3% of area increment of the Changjiang Estuary was attributed to reclamation.

Structural Analysis and Improved Design of the Gearbox Casing of a Certain Type of Tracked Vehicle

Loads on a gearbox casing of a certain type of tracked vehicle were calculated according to the engine＇s full load characteristic curve and the worst load condition where the gearbox operated while the tracked vehicle was running, and then stiffness and strength of the casing were analyzed by means of Patran/Nastran software. After a- nalysis, it was found that the casing satisfied the Mises ＇ yield condition; however, the stress distribution was hetero- geneous, and stresses near the bearing saddle bores of the casing were higher while those in other regions were much less than the allowable stress. For this reason, thicknesses of the casing wall on bearing assembling holes needed in- creasing, while those in other places can decrease. After much structural improving and re-analysis, the optimal casing design was found, and its weight decreased by 5% ; the casing still satisfied the Mises yield criterion and the stress distribution was more homogeneous.

Thermal-structural analysis of regeneratively-cooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Structural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter c3= 0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when c3〉 0.The results of sensitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.