Microstructure evolution of processed Mg-Al-Zn alloy by equal channel angularextrusion(ECAE) in semi-solid isothermal treatment was investigated. The results show that withincreasing semi-solid isothermal treatment te...Microstructure evolution of processed Mg-Al-Zn alloy by equal channel angularextrusion(ECAE) in semi-solid isothermal treatment was investigated. The results show that withincreasing semi-solid isothermal treatment temperature, the a phase solid grain size of processedMg-Al-Zn alloy by ECAE increases firstly due to coarsening of a phase solid grains, then decreasesdue to melting of a phase solid grains. With the increase of extrusion passes during ECAE, the aphase solid grain size in the following semi-solid isothermal treatment decreases. The a phase solidgrain size of processed Mg-Al-Zn alloy by ECAE under route B_C is the smallest, while the a phasesolid grain size of processed material by ECAE under route A is the largest. The primary mechanismof spheroid formation depends on the melting of recrystallizing boundaries and diffusion of soluteatoms in the semi-solid state.展开更多
Equal-channel angular pressing(ECAP) of an enhanced solid-solution treated 2024 Al alloy was successfully performed at room temperature, with an imposed equivalent normal strain of about 0.5. A very high hardness abou...Equal-channel angular pressing(ECAP) of an enhanced solid-solution treated 2024 Al alloy was successfully performed at room temperature, with an imposed equivalent normal strain of about 0.5. A very high hardness about HV191 and yield strength about 610 MPa (30% higher than those of the unECAPed 2024 Al alloy) in terms of commercial aluminum alloys were observed for the ECAPed 2024 Al alloy. In addition to the strengthening, this process allows the ECAPed 2024 Al alloy have a moderate level of tensile ductility (about 12.7%) and a significant strain hardening capability up to tensile failure. After aged at 373 K for 48 h, the ECAPed alloy increases its hardness (about HV201) and tensile ductility (about 14 %) further. The TEM results show that the ECAPed 2024 Al alloy presents a plate structure (about 50-100 nm) with high density of dislocation and additional thin plate (approximately <10 nm= inside. The XRD results show that the ECAP processing decreases the texture and increases the dislocation density of the alloy considerably. The theoretical calculations show that the increase of dislocation density resulting from ECAP processing makes a considerable contribution about 55.2 % for the improvement of yield strength.展开更多
This paper presents the results of equal channel angular pressing (ECAP) and subsequent heat treatment (HT) as a method to improve the wear resistance of metallic materials in friction sliding. The effect of ECAP and ...This paper presents the results of equal channel angular pressing (ECAP) and subsequent heat treatment (HT) as a method to improve the wear resistance of metallic materials in friction sliding. The effect of ECAP and HT on the microstructure and mechanical properties of low carbon steel is investigated in this work. The mechanisms of wear resistance of steel with ultrafine and nanostructures produced by equal-channel angular pressing is analyzed. The results show that ECAP at room temperature and annealing at 350°C and 450°C can be used as a technology of reducing wear in friction sliding.展开更多
基金Projects(50475029,50605015) supported by the National Natural Science Foundation of China
文摘Microstructure evolution of processed Mg-Al-Zn alloy by equal channel angularextrusion(ECAE) in semi-solid isothermal treatment was investigated. The results show that withincreasing semi-solid isothermal treatment temperature, the a phase solid grain size of processedMg-Al-Zn alloy by ECAE increases firstly due to coarsening of a phase solid grains, then decreasesdue to melting of a phase solid grains. With the increase of extrusion passes during ECAE, the aphase solid grain size in the following semi-solid isothermal treatment decreases. The a phase solidgrain size of processed Mg-Al-Zn alloy by ECAE under route B_C is the smallest, while the a phasesolid grain size of processed material by ECAE under route A is the largest. The primary mechanismof spheroid formation depends on the melting of recrystallizing boundaries and diffusion of soluteatoms in the semi-solid state.
基金Project(02KJD460004) supported by the Natural Science Foundation of Jiangsu Province, China
文摘Equal-channel angular pressing(ECAP) of an enhanced solid-solution treated 2024 Al alloy was successfully performed at room temperature, with an imposed equivalent normal strain of about 0.5. A very high hardness about HV191 and yield strength about 610 MPa (30% higher than those of the unECAPed 2024 Al alloy) in terms of commercial aluminum alloys were observed for the ECAPed 2024 Al alloy. In addition to the strengthening, this process allows the ECAPed 2024 Al alloy have a moderate level of tensile ductility (about 12.7%) and a significant strain hardening capability up to tensile failure. After aged at 373 K for 48 h, the ECAPed alloy increases its hardness (about HV201) and tensile ductility (about 14 %) further. The TEM results show that the ECAPed 2024 Al alloy presents a plate structure (about 50-100 nm) with high density of dislocation and additional thin plate (approximately <10 nm= inside. The XRD results show that the ECAP processing decreases the texture and increases the dislocation density of the alloy considerably. The theoretical calculations show that the increase of dislocation density resulting from ECAP processing makes a considerable contribution about 55.2 % for the improvement of yield strength.
文摘This paper presents the results of equal channel angular pressing (ECAP) and subsequent heat treatment (HT) as a method to improve the wear resistance of metallic materials in friction sliding. The effect of ECAP and HT on the microstructure and mechanical properties of low carbon steel is investigated in this work. The mechanisms of wear resistance of steel with ultrafine and nanostructures produced by equal-channel angular pressing is analyzed. The results show that ECAP at room temperature and annealing at 350°C and 450°C can be used as a technology of reducing wear in friction sliding.
