Two Blind Adaptive Equalizers Connected in Series for Equalization Performance Improvement

A variable step-size parameter is usually used to accelerate the convergence speed of a blind adaptive equalizer with N1 + N2 -1 coefficients where N1 and N2 are odd values. In this paper we show that improved equalization performance is achieved when using two blind adaptive equalizers connected in series where the first and second blind adaptive equalizer have N1 and N2 coefficients respectively compared with the case where a single blind adaptive equalizer is applied with N1 + N2 -1 coefficients. It should be pointed out that the same algorithm (cost function) is used for updating the filter taps for the different equalizers and that a fixed step-size parameter is used. Simulation results show that for the low signal to noise ratio (SNR) environment and for the case where the convergence speed is slow due to the channel characteristics, the new method has a faster convergence speed with a factor of approximately two while leaving the system with approximately the same or lower residual intersymbol interference (ISI).

Convergence Curve for Non-Blind Adaptive Equalizers

In this paper a closed-form approximated expression is proposed for the Intersymbol Interference (ISI) as a function of time valid during the entire stages of the non-blind adaptive deconvolution process and is suitable for the noisy, real and two independent quadrature carrier input case. The obtained expression is applicable for type of channels where the resulting ISI as a function of time can be described with an exponential model having a single time constant. Based on this new expression for the ISI as a function of time, the convergence time (or number of iteration number required for convergence) of the non-blind adaptive equalizer can be calculated. Up to now, the equalizer’s performance (convergence time and ISI as a function of time) could be obtained only via simulation when the channel coefficients were known. The new proposed expression for the ISI as a function of time is based on the knowledge of the initial ISI and channel power (which is measurable) and eliminates the need to carry out any more the above mentioned simulation. Simulation results indicate a high correlation between the simulated and calculated ISI (based on our proposed expression for the ISI as a function of time) during the whole deconvolution process for the high as well as for the low signal to noise ratio (SNR) condition.

A New Equalization Performance Analyzing Method for Blind Adaptive Equalizers Inspired by Maximum Time Interval Error

Up to now, the Mean Square Error (MSE) criteria, the residual Inter-Symbol Interference (ISI) and the Bit-Error-Rate (BER) were used to analyze the equalization performance of a blind adaptive equalizer in its convergence state. In this paper, we propose an additional tool (additional to the ISI, MSE and BER) for analyzing the equalization performance in the convergence region based on the Maximum Time Interval Error (MTIE) criterion that is used for the specification of clock stability requirements in telecommunications standards. This new tool preserves the short term statistical information unlike the already known tools (BER, ISI, MSE) that lack this information. Simulation results will show that the equalization performance of a blind adaptive equalizer obtained in the convergence region for two different channels is seen to be approximately the same from the residual ISI and MSE point of view while this is not the case with our new proposed tool. Thus, our new proposed tool might be considered as a more sensitive tool compared to the ISI and MSE method.

On the Performance Analysis of One Tap Equalizers in Oversampled OFDM Systems

Oversampling is commonly encountered in orthogonal frequency division multiplexing (OFDM) systems to ease various performance characteristics. In this paper, we investigate the performance and complexity of one tap zero-forcing (ZF) and minimum mean-square error (MMSE) equalizers in oversampled OFDM systems. Theoretical analysis and simulation results show that oversampling not only reduces the noise at equalizer output but also helps mitigate ill effects of spectral nulls. One tap equalizers therefore yield improved symbol-error-rate (SER) performance with the increase in oversampling rate, but at the expense of increased system bandwidth and modest complexity requirements.

Linear and Nonlinear Time Domain Block Equalizers on MIMO Frequency Selective Channels

Single-Carrier (SC) transmission with the same bandwidth as Multi-Carrier (MC) transmission (such as OFDM) may have far shorter symbol duration and is considered to be more robust against time selective fading. In this paper, we proposed the novel equalization and signal separation schemes in time domain for short block length transmission, i.e., Block Linear Equalization (BLE) and Block Nonlinear Equalization (BNLE) on MIMO frequency selective fading channels. The proposed BLE uses the MMSE based inverse matrix in time domain and the BNLE utilizes the QRD-M (QR Decomposition with M algorithm) with appropriate receiver complexity. We compared the computational complexity among the conventional SC-FDE (Frequency Domain Equalization) scheme and the proposed equalizers. We also used the Low-Density Parity Check (LDPC) decoder concatenated to the proposed BLE and BNLE.

Nonlinear Blind Equalizers: NCMA and NMCMA

This paper proposes two nonlinear blind equalizers: the nonlinear constant modulus algorithm (NCMA) and the nonlinear modified constant modulus algorithm (NCMA) by applying a nonlinear transfer function (NTF) into constant modulus algorithm (CMA) and modified constant modulus algorithm (MCMA), respectively. The effect of the NTF on CMA and MCMA is theoretically analyzed, which implies that the NTF can make their decision regions much sharper so that the proposed two nonlinear blind equalizers are more robust against the convergency error compared to their linear counterparts. The embedded single layer in NCMA and NMCMA simultaneously guarantees a comparably speedy convergency. On 16-quadrature amplitude modulation (QAM) symbols, computer simulations show that NCMA achieves an 8dB lower convergency mean square error (MSE) than CMA, and NMCMA achieves a 15dB lower convergency MSE than MCMA.

An Efficient Noise Generator for Validation of Channels Equalizers

This paper develops an efficient pseudo-random number generator for validation of digital communication channels and secure disc. Drives. Simulation results validates the effectiveness of the random number generator.

A 28/56 Gb/s NRZ/PAM-4 dual-mode transceiver with 1/4 rate reconfigurable 4-tap FFE and half-rate slicer in a 28-nm CMOS

A 28/56 Gb/s NRZ/PAM-4 dual-mode transceiver(TRx)designed in a 28-nm complementary metal-oxide-semiconduc-tor(CMOS)process is presented in this article.A voltage-mode(VM)driver featuring a 4-tap reconfigurable feed-forward equal-izer(FFE)is employed in the quarter-rate transmitter(TX).The half-rate receiver(RX)incorporates a continuous-time linear equal-izer(CTLE),a 3-stage high-speed slicer with multi-clock-phase sampling,and a clock and data recovery(CDR).The experimen-tal results show that the TRx operates at a maximum speed of 56 Gb/s with chip-on board(COB)assembly.The 28 Gb/s NRZ eye diagram shows a far-end vertical eye opening of 210 mV with an output amplitude of 351 mV single-ended and the 56 Gb/s PAM-4 eye diagram exhibits far-end eye opening of 33 mV(upper-eye),31 mV(mid-eye),and 28 mV(lower-eye)with an output amplitude of 353 mV single-ended.The recovered 14 GHz clock from the RX exhibits random jitter(RJ)of 469 fs and deterministic jitter(DJ)of 8.76 ps.The 875 Mb/s de-multiplexed data features 593 ps horizontal eye opening with 32.02 ps RJ,at bit-error rate(BER)of 10-5(0.53 UI).The power dissipation of TX and RX are 125 and 181.4 mW,respectively,from a 0.9-V sup-ply.

Ultrahigh strength and improved electrical conductivity in an aging strengthened copper alloy processed by combination of equal channel angular pressing and thermomechanical treatment

In this paper,equal channel angular pressing and thermomechanical treatment was employed to improve the strength and electrical conductivity of an aging strengthened Cu-Ti-Cr-Mg alloy,and the microstructure and properties of the alloy were investigated in detail.The results showed that the samples deformed by the combination of cryogenic equal channel angular pressing(ECAP)and rolling had good comprehensive properties after aging at 400℃.The tensile strength of the peak-aged and over-aged samples was 1120 MPa and 940 MPa,with their corresponding electrical conductivity of 14.7%IACS and 22.1%IACS,respectively.ECAP and cryogenic rolling introduced high density dislocations,leading to the inhibition of the softening effects and refinement of the grains.After a long time aging at 400℃,the alloy exhibited ultra-high strength with obvious increasing electrical conductivity.The high strength was attributed to the synergistic effect of work hardening,grain refinement strengthening and precipitation strengthening.The precipitation of a large amount of Ti atoms from the matrix led to the high electrical conductivity of the over-aged sample.

WEAK-STRONG UNIQUENESS FOR THREE DIMENSIONAL INCOMPRESSIBLE ACTIVE LIQUID CRYSTALS

The hydrodynamics of active liquid crystal models has attracted much attention in recent years due to many applications of these models.In this paper,we study the weak-strong uniqueness for the Leray-Hopf type weak solutions to the incompressible active liquid crystals in R^(3).Our results yield that if there exists a strong solution,then it is unique among the Leray-Hopf type weak solutions associated with the same initial data.

Equalization Reconstruction Algorithm Based on Reference Signal Frequency Domain Block Joint for DTMB-Based Passive Radar

Channel equalization plays a pivotal role within the reconstruction phase of passive radar reference signals.In the context of reconstructing digital terrestrial multimedia broadcasting(DTMB)signals for low-slow-small(LSS)target detection,a novel frequency domain block joint equalization algorithm is presented in this article.From the DTMB signal frame structure and channel multipath transmission characteristics,this article adopts a unconventional approach where the delay and frame structure of each DTMB signal frame are reconfigured to create a circular convolution block,facilitating concurrent fast Fourier transform(FFT)calculations.Following equalization,an inverse fast Fourier transform(IFFT)-based joint output and subsequent data reordering are executed to finalize the equalization process for the DTMB signal.Simulation and measured data confirm that this algorithm outperforms conventional techniques by reducing signal errors rate and enhancing real-time processing.In passive radar LSS detection,it effectively suppresses multipath and noise through frequency domain equalization,reducing false alarms and improving the capabilities of weak target detection.

A New Equalization Method for Lithium-Ion Battery Packs Based on CUK

Aiming at the traditional CUK equalizer can only perform energy equalization between adjacent batteries,if the two single batteries that need to be equalized are far away from each other,there will be the problem of longer energy transmission path and lower equalization efficiency,this paper optimizes the CUK equalizer and optimizes its peripheral selection circuit,which can support the equalization of single batteries at any two positions.The control strategy adopts the open-circuit voltage(OVC)of the battery and the state of charge(SOC)of the battery as the equalization variables,and selects the corresponding equalization variables according to the energy conditions of the two batteries that need to be equalized,and generates the adaptive equalization current with an adaptive PID controller in order to improve the equalization efficiency.Simulation modeling is performed in Matlab/Simulink 2021b,and the experimental results show that the optimized CUK equalizer in this paper improves the equalization time by 25.58%compared with the traditional CUK equalizer.In addition,compared with the mean value difference(MVD)method,the adaptive PID method reduces the equalization time by about 30%in the static and charging and discharging experimental environments,which verifies the superiority of this equalization scheme.

Automatic SOC Equalization Strategy of Energy Storage Units with DC Microgrid Bus Voltage Support

In this paper,an improved sag control strategy based on automatic SOC equalization is proposed to solve the problems of slow SOC equalization and excessive bus voltage fluctuation amplitude and offset caused by load and PV power variations in a stand-alone DC microgrid.The strategy includes primary and secondary control.Among them,the primary control suppresses the DC microgrid voltage fluctuation through the I and II section control,and the secondary control aims to correct the P-U curve of the energy storage system and the PV system,thus reducing the steady-state bus voltage excursion.The simulation results demonstrate that the proposed control strategy effectively achieves SOC balancing and enhances the immunity of bus voltage.The proposed strategy improves the voltage fluctuation suppression ability by approximately 39.4%and 43.1%under the PV power and load power fluctuation conditions,respectively.Furthermore,the steady-state deviation of the bus voltage,△U_(dc) is only 0.01–0.1 V,ensuring stable operation of the DC microgrid in fluctuating power environments.

Assessing the Spatial Equality of COVID Testing Sites Maintaining Zero COVID Policy

Rapid and timely testing is essential to minimize the COVID-19 spread. Decision makers and policy planners need to determine the equal distribution and accessibility of testing sites. This study mainly examines the spatial equality of COVID-19 testing sites that maintain a zero COVID policy in Guangzhou City. The study has identified the spatial disparities of COVID testing sites, characteristics of testing locations, and accessibility. The study has obtained information on COVID testing sites in Guangzhou City and population data. Point pattern analyses, Euclidian distance and allocation, and network analyses are the main methods used to achieve the research objectives, and 1183 total COVID testing sites can be recognized in Guangzhou City. Results revealed that spatial disparities could be noticed over the study area. Testing locations of Guangzhou City are highly clustered. The most significant testing sites are located in Haizhu District, which has the third largest population. The highest population density can be identified in Yuexiu District. However, only 94 testing sites are located there. According to all the results, higher disparities can be identified, and a lack of testing sites is located in the north part of the study area. Some people in the northern part have to travel more than 10 km to reach a testing site. Finally, this paper suggests increasing the number of testing sites in the north and south parts of the study area and keeping the same distribution, considering the area, total population, and population density. This kind of research will be helpful to decision-makers in making proper decisions to maintain a zero COVID policy.

Pursuing Common Good for All under Heaven

Fairness,justice,and equality are long existing pursuits of Chinese philosophers from ancient times to today.AS a political ideal,the ancient Chinese saying“Tian Xia Wei Gong”,or“pursuing common good for all under heaven”has been influencing Chinese politics and collective mind of the Chinese people since the time Confucius proposed it.

GENDER EQUALITY IN THE CHINESE WORKPLACE

Gender equality is a significant issue in the economic and social sectors.A McKinsey study found that promoting gender equality in the workplace could contribute US$13 trillion to global GDP growth.And if China reaches the forefront of gender equality in the workplace in the Asia-Pacific region,it would generate about US$3 trillion in GDP.

News-Clips(2024. 02-2024. 03)

February 2024 State councilor urges high-quality work for women,children Chinese State Councilor Shen Yiqin has urged efforts to advance the high-quality development of work for women and children during her inspection tour in east China’s Fujian Province.From Feb.2 to Feb.3,Shen inspected local service centers for women and children in the provincial capital city of Fuzhou and visited rural areas and urban communities to learn about relevant work.Shen,also president of the All-China Women’s Federation,called for efforts to ensure the Party’s leadership over the work of women’s federations,focus on the most practical and tangible matters for women and their families,and promote gender equality and all-around development of women and children.

Advancement Towards Spatial Justice:The Barrier-Free Environment Construction from a Gender Perspective

Space is both a product and a producer of social relations.In the spatial domain,gender blindness has long existed,limiting women’s rights of access to and use of space,leading to structural oppression of women’s rights,and giving rise to new gender inequalities.The barrier-free environment construction has the functions of eliminating physical barriers and generating societal norms,and when combined with social changes,can facilitate justice correction across multiple dimensions.However,barrier-free environment construction itself,as a means of justice correction,also suffers from gender blindness.There remains room for improvement in the areas of facility construction,information exchange,and social services within the realm of barrier-free environments.In response to this phenomenon,gender equality offers a new critical perspective.Therefore,integrating a gender perspective into the barrier-free environment construction,focusing on the spatial rights of women,especially groups with multiple vulnerabilities,such as disabled women and elderly women,can contribute to the advancement towards spatial justice.

Near-Field Beam Training for Holographic MIMO Communications: Typical Methods, Challenges and Future Directions

Holographic multiple-input multiple-output(HMIMO)has become an emerging technology for achieving ultra-high frequency spectral efficiency and spatial resolution in future wireless systems.The increasing antenna aperture leads to a more significant characterization of the spherical wavefront in near-field communications in HMIMO scenarios.Beam training as a key technique for wireless communication is worth exploring in this near-field scenario.Compared with the widely researched far-field beam training,the increased dimensionality of the search space for near-field beam training poses a challenge to the complexity and accuracy of the proposed algorithm.In this paper,we introduce several typical near-field beam training methods:exhaustive beam training,hierarchical beam training,and multi-beam training that includes equal interval multi-beam training and hash multi-beam training.The performances of these methods are compared through simulation analysis,and their effectiveness is verified on the hardware testbed as well.Additionally,we provide application scenarios,research challenges,and potential future research directions for near-field beam training.

Bound State Description of Particles from a Quantum Field Theory of Fermions and Bosons, Compatible with Relativity

Both, the dilemma to find a quantum field theory consistent with Einstein’s law of relativity and the problem to describe existing particles as bound states of matter has been solved by calculating bound state matrix elements from a dual fermion-boson Lagrangian. In this formalism, the fermion binding energies are compensated by boson energies, indicating that particles can be generated out of the vacuum. This yields quantitative solutions for various mesons ω (0.78 GeV) - Υ (9.46 GeV) and all leptons e, μ and τ, with uncertainties in the extracted properties of less than 1‰. For transparency, a Web-page with the address htpps://h2909473.stratoserver.net has been constructed, where all calculations can be run on line and also the underlying fortran source code can be inspected.