A transceiver frequency conversion module based on 3D micropackaging technology

The idea of Ku-band transceiver frequency conversion module design based on 3D micropackaging technology is proposed. By using the double frequency conversion technology,the dual transceiver circuit from Ku-band to L-band is realized by combining with the local oscillator and the power control circuit to complete functions such as amplification, filtering and gain. In order to achieve the performance optimization and a high level of integration of the Ku-band monolithic microwave integrated circuits(MMIC) operating chip, the 3 D vertical interconnection micro-assembly technology is used. By stacking solder balls on the printed circuit board(PCB), the technology decreases the volume of the original transceiver to a miniaturized module. The module has a good electromagnetic compatibility through special structure designs. This module has the characteristics of miniaturization, low power consumption and high density, which is suitable for popularization in practical application.

Quantum frequency down-conversion of single photons at 1552 nm from single InAs quantum dot

Near-infrared single photon sources in telecommunication bands, especially at 1550 nm, are required for long-distance quantum communication. Here a down-conversion quantum interface is implemented, where the single photons emitted from single In As quantum dot at 864 nm is down converted to 1552 nm by using a fiber-coupled periodically poled lithium niobate（PPLN） waveguide and a 1.95 μmm pump laser, and the frequency conversion efficiency is ~40%. The singlephoton purity of quantum dot emission is preserved during the down-conversion process, i.e., g^（（2））（0）, only 0.22 at 1552 nm.This present technique advances the Ⅲ-Ⅴ semiconductor quantum dots as a promising platform for long-distance quantum communication.

Noise-free frequency conversion of quantum states

In this paper, the frequency conversion of quantum states based on the intracavity nonlinear interaction is proposed. The fidelity of an input state after frequency conversion is calculated, and it is shown the noise-free frequency conversion of a quantum state can be achieved by injecting a strong signal field. The dependences of conversion efficiency on the pump parameter, extra losses and input state amplitude are also analysed.

Quantum frequency up-conversion with a cavity

The quantum state transfer from subharmonic frequency to harmonic frequency based on asymmetrically pumped second harmonic generation in a cavity is investigated theoretically. The performance of noise-free frequency up- conversion is evaluated by the signal transfer coefficient and the conversion efficiency, in which both the quadrature fluctuation and the average photon number are taken into consideration. It is shown that the quantum property can be preserved during frequency up-conversion via operating the cavity far below the threshold. The dependences of the transfer coefficient and the conversion efficiency on pump parameter, analysing frequency, and cavity extra loss are also discussed.

Multiple frequency conversion via atomic spin coherence of storing a light pulse

We experimentally demonstrate multiple frequency conversion via atomic spin coherence of storing a light pulse in a doped solid. The essence of this multiple frequency conversion is four-wave mixing based on stored atomic spin coherence. Through electromagnetically induced transparency, an input probe pulse is stored into atomic spin coherence by modulating the intensity of the control field. By using two different control fields to interact with the coherently prepared medium, the stored atomic spin coherence can be transformed into three different information channels. Multiple frequency conversion is implemented efficiently by manipulating the spectra of the control fields to scatter atomic spin coherence. This multiple frequency conversion is expected to have potential applications in information processing and communication network.

Advanced Power Module Packaging and Integration Structures for High Frequency Power Conversion：From Silicon to GaN

The emerging of commercial high-voltage gallium nitride(GaN) power devices provides extraordinary switching performance over silicone devices, which enables high-voltage power conversion switching at megahertz range.Such outstanding features also pose strong challenges for device packaging design since the package parasitics can significantly influence the device switching characteristics, and thus can shadow the advantages brought by GaN devices. Designers have been dealing with these challenges brought by high du/dt and high-frequency switching operation even since the silicon(Si) era when fast switching Si MOSFET is first developed and came up with lots of inspiring advanced power module packaging structures to mitigate the problems.This paper presents a review of advanced power module packaging and integration structures that are suitable for high frequency power conversion.The review covers the heritage from the high frequency Si MOSFET packaging to the state-of-the-art for GaN devices.

Decoupled estimation of frequency-dependent IQI and channel for OFDM systems with direct-conversion transceivers

The in-phase and quadrature-phase imbalance (IQI) is one of the major radio frequency impairments existing in orthogonal frequency division multiplexing (OFDM) systems with direct-conversion transceivers. During the transmission of the communication signal, the impact of IQI is coupled with channel impulse responses (CIR), which makes the traditional channel estimation schemes ineffective. A decoupled estimation scheme is proposed to separately estimate the frequency-dependent IQI and wireless channel. Firstly, the generalized channel model is built to separate the parameters of IQI and wireless channel. Then an iterative estimation scheme of frequency-dependent IQI is designed at the initial stage of communication. Finally, based on the estimation result of IQI, the least square algorithm is utilized to estimate the channel-related parameters at each time of channel variation. Compared with the joint estimation schemes of IQI and channel, the proposed decoupled estimation scheme requires much lower training overhead at each time of channel variation. Simulation results demonstrate the good estimation performance of the proposed scheme.

采用移相控制的具有软开关能力的交错图腾杆无桥Boost PFC变换器

该文提出了一种具有软开关能力的图腾杆式无桥交错Boost功率因数校正器(power factor correction,PFC).与传统的交错图腾杆无桥升压PFC变换器相比,在2个PFC变换器单元之间增加了一个电感,利用增加电感的能量,使所有开关实现零电压开关.此外,通过在2个PFC变换器单元之间应用移相控制,使得变换器可以将所加电感上的电流大小控制为一个最优值.因此,该变换器可以实现零电压工作,同时最大限度地降低附加电感的导通损耗和铁心损耗.通过Matlab Simulink仿真的结果表明:该变换器可以达到较高的效率,验证了该变换器的可行性.

Frequency Up-conversion Luminescence Properties and Mechanism of Tm^(3+) /Er^(3+)/Yb^(3+) Co-doped Oxyfluorogermanate Glasses

Oxyfluoride glasses were developed with composition 60GeO 2 ·10AlF 3 ·25BaF 2 ·（1.95-x）GdF 3 · 3YbF 3 ·0.05TmF 3 ·xErF 3 （x=0.02,0.05,0.08,0.11,0.14,0.17）in mole percent.Intense blue（476 nm）,green（524 and 546 nm）and red（658 nm）emissions which identified from the 1G 4 →3H 6 transition of Tm3＋and the（2H 11/2 ,4S 3/2 ）→4I 15/2 ,4F 9/2 →4I 15/2 transitions of Er3＋,respectively,were simultaneously observed under 980 nm excitation at room temperature.The results show that multicolor luminescence including white light can be adjustably tuned by changing doping concentrations of Er3＋ion or the excitation power.In addition,the energy transfer processes among Tm3＋,Er3＋and Yb3＋ions,and up-conversion mechanisms are discussed.

Nonreciprocal Single Photon Frequency Conversion via Chiral Coupling between a V-Type System and a Pair of Waveguides

The single photon frequency conversion is investigated theoretically in the system composed of a V-type system chiral coupling to a pair of waveguides. The single photon scattering amplitudes are obtained using the real-space Hamiltonian. The calculated results show that the probability of single photon frequency down-or up-conversion can reach a unit by choosing appropriate parameters in the non-dissipative system with perfect chiral coupling.We present a nonreciprocal single photon beam splitter whose frequency of the output photon is different from that of the input photon. The influences of dissipations and non-perfect chiral coupling on the single frequency conversion are also shown. Our results may be useful in designing quantum devices at the single-photon level.

Scheme for implementing frequency up-conversion between two collective atomic modes

This paper presents a scheme for realizing the frequency up-conversion between two collective atomic modes. In the scheme two atomic samples are coupled to a cavity mode. Under the large detuning condition, the two collective atomic modes are coupled via the virtual excitation of the cavity mode and the effective Hamiltonian corresponds to the frequency up-conversion. In the scheme the cavity mode is only virtually excited and thus the process is insensitive to cavity decay.

Conversion of Kinetic Energy from Synoptic Scale Disturbance to Low-Frequency Fluctuation over the Yangtze River Valley in the Summers of 1997 and 1999

In order to investigate the conversion of kinetic energy from a synoptic scale disturbance （SSD; period≤seven days） to a low-frequency fluctuation （LFF; period〉seven days）, the budget equation of the LFF kinetic energy is derived. The energy conversion is then calculated and analyzed for the summers of 1997 and 1999. The results show that the energy conversion from the SSD to the LFF is obviously enhanced in the middle and lower troposphere during the heavy rainfall, suggesting this to be one of mechanisms inducing the heavy rainfall, although the local LFF kinetic energy may not be enhanced.

基于智能制造的造纸机传动系统变频调速控制研究

进入21世纪以来,科技飞速发展,经济水平不断得到提高,人们对纸张的差异化需求越来越突出,不仅包括纸张的质量,更重要的是纸张的功能性。在造纸企业的生产中,智能化的造纸设备对企业的发展影响巨大。在智能化的造纸设备中,传动系统处于核心的位置,通过变频的方式实现传动系统的有序运转,有利于节约能源,同时保证仪器的平稳运行。为此,对造纸及传动系统进行深入研究,分析了造纸机在变频调速方面面临的挑战与机遇,为加速造纸机的升级以及造纸行业的进一步发展,促进纸张的智能化生产提供了借鉴。

目标探测回波模拟单元可重构测试技术研究

现有空空导弹在柔性、可重构、快速响应等设计和研制方面与国际领先水平和军事需求相比还存在严重不足。其研发系统架构和生产研制架构形式已经无法满足未来的发展需求,特别是目标探测部件等核心关键组件。重点探索目标探测部件的新型可重构测试架构形式,通过模块化、标准化和通用化的模组组合,针对不同型号产品搭建快速验证平台,完成性能测试。提出了一种目标探测部件回波模拟单元的柔性可重构测试技术,通过对目标模拟单元的可重构设计,快速形成目标探测部件测试平台。

抽油机井恒功率变频控制系统研究

抽油机作为陆上油田最重要的机械采油装备之一,近年来已发展出一系列的变频节能技术,但其研究主要集中在硬件方面,缺乏相关基础理论,导致现场应用普适性差,应用效果参差不齐。为此,研究有杆泵变频测控机理,优选了主要部件,对测试数据提出了要求,形成了有杆泵抽油变频控制系统。构建BP神经网络系统对正常井和漏失、柱塞碰泵、气体影响等异常井进行识别,分类提出变频计算模型:考虑负扭矩和抽油机冲次界限等建立了正常井恒功率变频计算模型,实例对比分析了变频后抽油机速度、加速度变化规律,产液量一定时,负功功率和有功功率分别下降了65%和44%。建立了上行程漏失的异常井变频计算模型,针对性地提高上行程冲次,形成“上快下慢”运行模式。实例计算表明:该系统缩短上行程时间2.6 s,较好地解决有杆泵上行程漏失和变频节能的问题。研究成果可为抽油机变频技术提供理论支持,对油田节能和提产具有指导意义。

锦屏复杂地下洞室施工通风智能调控研究

锦屏大设施具有多洞室、多工作面,通风网络复杂等特点,为确保洞室空气质量并解决施工期通风高能耗问题,通过优化隧道需风量计算方法,确定风压阻力损失,进行施工通风计算。根据风机布设位置,划分供排风区域,明确了风机控制区域;基于各区域风量、风压,得出了风机运行功率计算式并细分风机档位,形成了地下洞室施工期风机变频调节策略;通过布设空气质量监测设备,建立了软件平台,可视化远程控制地下洞室空气质量,自动监测、处理数据指导变频器控制风机变频,并利用污染物浓度监测数据验证了变频通风有效性。研究结果表明:1)风机运行频率可随洞室内污染物浓度及时变化;2)通风智能调控可有效降低污染物浓度;3)通风智能调控可降低施工通风能耗,实现施工期智能化通风。

多域特征引导的无监督SAR图像舰船检测方法

如何在合成孔径雷达(SAR)图像标注样本有限的条件下,提升舰船检测性能一直是SAR图像处理中的热点问题。本文提出一种多域特征引导的无监督域适应方法,将知识从有标注的源域(光学图像)转移到未标注的目标域(SAR图像),降低对标记SAR图像数据依赖。同时,设计了频域转换模块、注意力区域增强模块和自适应权重模块来缩小光学、SAR图像域之间的域差距,提高源域与目标域特征对齐效率,增强网络在挑战性样本下的特征迁移能力。在公开发布的数据集上进行了大量实验。结果表明:所提的模块较基础模型AP50提升10%,总体性能优于其他先进的方法。

晶闸管和IGBT混合的三相电机两相变频控制策略

现有三相交直交变频电路中大多使用IGBT作为电力电子器件,为了进一步降低低压大容量变频器设备成本,减少IGBT的使用,提出了一种晶闸管和IGBT混合的三相电机两相变频电路结构及四开关八电压矢量直接转矩控制策略.首先分析了利用IGBT辅助晶闸管关断的三相电机两相变频电路结构,并分析了不同开关状态下的瞬时电路工作原理,给出三相四开关拓扑下的八电压矢量生成方法;其次提出四开关八矢量异步电机直接转矩控制策略,并给出扇区划分、电压矢量选择和电压矢量伏秒生成原理;最后通过仿真实验验证所提策略的正确性和可行性.仿真结果验证了上述电路结构和控制方法的有效性.

船用无线电标校信标机程控频点切换的设计

船用无线电标校信标机是指能够为船载统一测控设备提供稳定跟踪信号的射频信号发生器。一般安装于探空气球内部或悬挂于无人机底部,经过飞行至一定高度和距离后,船载统一测控设备对该信标信号进行跟踪试验。当前船用无线电标校信标机在空中仅能工作在一个频点,若需要对多个工作频点进行标校则需要重复释放多个无线电信标机。为解决此问题,设计一种标校信标机外围变频控制电路,将该电路连接至标校信标机即可完成释放一个信标机开展多频点标校的难题。该变频电路以低功耗单片机STC89C52RC作为基本控制单元,结合DC⁃DC降压模块和电平转换模块,实现将多个预置工作频点信息按预定帧格式定时发送至信标机的功能。经过十余次海上航天测量试验的检验,结果表明程控变频控制电路运行稳定、控制精度高,节省了标校时间和经费预算。

CLLLC谐振变换器的分级寻优模型预测控制

针对CLLLC谐振变换器提出了一种基于分级寻优模型预测的混合控制策略。通过结合变频控制与移相控制的优点,在实现软开关的同时,能拓宽变换器的电压增益范围。该策略不仅减小了普通有限集模型预测控制(MPC)策略的计算量,还改善了PI控制存在的电压超调大和动态响应慢的问题,在稳态性能相近的情况下提升了变换器系统的动态性能。最后通过Matlab/Simulink仿真和实验证明了分级寻优MPC策略的有效性。