期刊文献+
共找到24篇文章
< 1 2 >
每页显示 20 50 100
Effect of Sc on Al_(3)Fe phase and mechanical properties of as-cast AA5052 aluminum alloy
1
作者 Yang Li Qing Yu +3 位作者 Feng-feng Chen Jia-wen He Hong-mei Yang Meng-nie Li 《China Foundry》 SCIE EI CAS CSCD 2024年第3期257-264,共8页
The AA5052 aluminum alloy is widely used in automobile and aerospace manufacturing,and with the development of light-weight alloys,it is required that these materials exhibit better mechanical properties.Previous stud... The AA5052 aluminum alloy is widely used in automobile and aerospace manufacturing,and with the development of light-weight alloys,it is required that these materials exhibit better mechanical properties.Previous studies have demonstrated that the addition of Sc to aluminum alloys can improve both the microstructure and properties of the alloys.In this study,the effect of Sc on the Fe-rich phase and properties of the AA5052 aluminum alloy was studied by adding 0%,0.05%,0.2%,and 0.3%Sc.The results show that with the increase of Sc,the coarse needle-like Fe-rich phase gradually transforms into Chinese-script and then nearly spherical particles,reduce the size of Fe-rich phase,and refine the grain with increase of high angle grain boundaries(HAGBs).These microstructure changes enhance the strength of the AA5052 alloy through Sc addition.The ductility of the alloy is obviously improved because the addition of a lower amount of Sc changes the morphology of Fe-rich phase from needle-like into a Chinese-script,and it is subsequently reduced as a result of significant increase in HAGBs with increasing Sc content. 展开更多
关键词 AA5052 aluminum alloy Al3fe phase mechanical properties grain boundary
下载PDF
Coercivity enhancement of sintered Nd–Fe–B magnets by grain boundary diffusion with Pr_(80-x)Al_(x)Cu_(20)alloys
2
作者 金哲欢 金磊 +10 位作者 丁广飞 郭帅 郑波 樊思宁 王志翔 范晓东 朱金豪 陈仁杰 闫阿儒 潘晶 刘新才 《Chinese Physics B》 SCIE EI CAS CSCD 2023年第1期516-521,共6页
A grain boundary diffusion(GBD)process with Pr_(80-x)Al_(x)Cu_(20)(x=0,10,15,20)low melting point alloys was applied to commercial 42M sintered Nd–Fe–B magnets.The best coercivity enhancement of a diffused magnet wa... A grain boundary diffusion(GBD)process with Pr_(80-x)Al_(x)Cu_(20)(x=0,10,15,20)low melting point alloys was applied to commercial 42M sintered Nd–Fe–B magnets.The best coercivity enhancement of a diffused magnet was for the Pr_(65)Al_(15)Cu_(20)GBD magnet,from 16.38 kOe to 22.38 kOe.Microstructural investigations indicated that increase in the Al content in the diffusion source can form a continuous grain boundary(GB)phase,optimizing the microstructure to enhance the coercivity.The coercivity enhancement is mainly due to the formation of a continuous GB phase to separate the main phase grains.Exchange decoupling between the adjacent main phase grains is enhanced after the GBD process.Meanwhile,the introduction of Al can effectively promote the infiltration of Pr into the magnet,which increases the diffusion rate of rare-earth elements within a certain range.This work provides a feasible method to enhance coercivity and reduce the use of rare-earth resources by partial replacement of rare-earth elements with non-rare-earth elements in the diffusion source. 展开更多
关键词 Nd–fe–B grain boundary diffusion coercivity enhancement grain boundary phase
下载PDF
Optimization of the grain boundary diffusion process by doping gallium and zirconium in Nd–Fe–B sintered magnets
3
作者 李之藤 徐海波 +5 位作者 刘峰 赖荣舜 武仁杰 李志彬 张洋洋 马强 《Chinese Physics B》 SCIE EI CAS CSCD 2023年第10期649-655,共7页
As the channel for grain boundary diffusion(GBD)in Nd–Fe–B magnets,grain boundary(GB)phases have a very important effect on GBD.As doping elements that are commonly used to regulate the GB phases in Nd–Fe–B sinter... As the channel for grain boundary diffusion(GBD)in Nd–Fe–B magnets,grain boundary(GB)phases have a very important effect on GBD.As doping elements that are commonly used to regulate the GB phases in Nd–Fe–B sintered magnets,the influences of Ga and Zr on GBD were investigated in this work.The results show that the Zr-doped magnet has the highest coercivity increment(7.97 kOe)by GBD,which is almost twice that of the Ga-doped magnet(4.32 kOe)and the magnet without Ga and Zr(3.24 kOe).Microstructure analysis shows that ZrB_(2)formed in the Zr-doped magnet plays a key role in increasing the diffusion depth.A continuous diffusion channel in the magnet can form because of the presence of ZrB_(2).ZrB_(2)can also increase the defect concentration in GB phases,which can facilitate GBD.Although Ga can also improve the diffusion depth,its effect is not very obvious.The micromagnetic simulation based on the experimental results also proves that the distribution of Tb in the Zr-doped magnet after GBD is beneficial to coercivity.This study reveals that the doping elements Ga and Zr in Nd–Fe–B play an important role in GBD,and could provide a new perspective for researchers to improve the effects of GBD. 展开更多
关键词 Nd–fe–B sintered magnet ZrB_(2)phase grain boundary diffusion micromagnetic simulation
下载PDF
^(57)Fe Mössbauer spectrometry: A powerful technique to analyze the magnetic and phase characteristics in RE–Fe–B permanent magnets 被引量:1
4
作者 赵利忠 张雪峰 +2 位作者 严密 刘仲武 Jean-Marc Greneche 《Chinese Physics B》 SCIE EI CAS CSCD 2021年第1期73-86,共14页
This review summarizes the recent advances on the application of ^(57)Fe Mössbauer spectrometry to study the magnetic and phase characteristics of Nd–Fe–B-based permanent magnets. First of all, the hyperfine st... This review summarizes the recent advances on the application of ^(57)Fe Mössbauer spectrometry to study the magnetic and phase characteristics of Nd–Fe–B-based permanent magnets. First of all, the hyperfine structures of the Ce_(2)Fe_(14)B,(Ce,Nd)_(2)Fe_(14)B and MM_(2)Fe_(14)B phases are well-defined by using the model based on the Wigner-Seitz analysis of the crystal structure. The results show that the isomer shift δ and the quadrupole splitting öEQ of those 2:14:1 phases show minor changes with the Nd content, while the hyperfine field Bhfincreases monotonically with increasing Nd content and its value is influenced by the element segregation and phase separation in the 2:14:1 phase. Then, the hyperfine structures of the low fraction secondary phases are determined by the ^(57)Fe Mössbauer spectrometry due to its high sensitivity. On this basis,the content, magnetic behavior, and magnetization of the REFe_(2) phase, the amorphous grain boundary(GB) phase, and the amorphous worm-like phase, as well as their effects on the magnetic properties, are systematically studied. 展开更多
关键词 ^(57)fe Mössbauer spectrometry Nd–fe–B-based permanent magnets (Ce Nd)_(2)fe_(14)B phase grain boundary phase
下载PDF
In-situ observations on interphase boundary migration and grain growth during α/γ phase transformation in iron-4.2%Cr alloy
5
作者 渡边忠雄 OBARA Kouichi TSUREKAWA Sadahiro 《材料与冶金学报》 CAS 2005年第2期91-91,共1页
In-situ observations on α/γ phase transformation were made to study the effects of grain boundary microstructures on the formation of a new phase and the migration of α/γ interphase boundary in an iron4. 2%Cr allo... In-situ observations on α/γ phase transformation were made to study the effects of grain boundary microstructures on the formation of a new phase and the migration of α/γ interphase boundary in an iron4. 2%Cr alloy. It was found that triple junctions with more random boundaries could be the primary nucleation sites for a new phase, while triple junctions with low angle or low ∑ coincidence boundaries did not play any role as preferential sites. The migration of α/γ interphase boundary during heating over the transformation temperature range showed the two stage behaviour characterized by a stage with a migration velocity of 0. 33-0. 75 mm/s and secondly by a stage with 3. 7-7. 6 mm/s. It was also found that abnormal grain growth and a high density of ∑3 coincidence boundaries could occur in a phase with bcc structure after cycling of α/γ phase transformation. A new mechanism of nucleation and growth of a new phase in α/γ phase transformation is proposed on the basis of roles of plane-matching interphase boundaries, as previously discussed on the origin of anisotropy of grain growth due to the migration of {110} plane-matching boundaries in Fe-3z%Si alloy. The most recent theoretical work on the distribution of plane-matching boundaries in solids with different crystal structures was found to be useful for the understanding of nucleation and growth during α/γ phase transformation. 展开更多
关键词 In-situ phase velocity stage effects crystal with random origin the range after new was more play over high MOST for The to DID BCC It be
下载PDF
Nd_2Fe_(14)B/α-Fe/非晶Nd-Fe-B三相纳米交换耦合磁体中的结构弛豫 被引量:2
6
作者 计齐根 田宗军 +2 位作者 顾本喜 章建荣 都有为 《金属学报》 SCIE EI CAS CSCD 北大核心 2001年第5期463-466,共4页
用旋淬法制备了Nd2Fe14B/α-Fe基复相纳米交换耦合磁体粉末样品.发现样品由于在室温下的结构弛豫导致磁性能的较大变化.在淬态Nd-Fe-B非晶相和Nd2Fe14B/α-Fe纳米晶共存的三相交换磁体中,其效果更为... 用旋淬法制备了Nd2Fe14B/α-Fe基复相纳米交换耦合磁体粉末样品.发现样品由于在室温下的结构弛豫导致磁性能的较大变化.在淬态Nd-Fe-B非晶相和Nd2Fe14B/α-Fe纳米晶共存的三相交换磁体中,其效果更为明显.而在淬态完全非晶态或晶态的单相或复相交换磁体中,结构弛豫对磁性能的影响较弱.淬态Nd10Fe83B6In磁体粉末经过在室温下置放1年时间后,内禀矫顽力Hc由刚出炉时的296kA/m增加至384kA/m,剩磁比mr从0.55增至0.62非晶相的存在为晶粒发展完备的晶界提供了可能.应力和缺陷集中的边界区域的结构弛豫和原子调整使得相邻接的相与相、晶粒与晶粒之间的结晶学相关性提高,交换耦合增强.同时完善的晶界也增强磁体的磁硬化.X射线衍射结果显示结构弛豫的最终结果使得衍射峰宽化,极有可能在晶界处形成了畸变的晶间相.而正是这种畸变的晶间相对磁性能的增强起了关键的作用. 展开更多
关键词 ND2fe14B/Α-fe 多相纳米交换耦合磁体 结构弛豫 晶间相
下载PDF
晶界η相对Fe-Ni-Cr奥氏体合金力学性能的影响 被引量:15
7
作者 李秀艳 戎利建 李依依 《金属学报》 SCIE EI CAS CSCD 北大核心 2005年第11期1155-1158,共4页
通常认为Fe-Ni-Cr合金在过时效后晶界上析出的η相为裂纹源,恶化合金性能.通过对一种Fe-Ni-Cr合金进行过时效后晶界上析出η相的研究发现,由于晶界η相与合金基体保持共格关系,η相对合金的室温性能影响不大;并且在高温变形条件下η相... 通常认为Fe-Ni-Cr合金在过时效后晶界上析出的η相为裂纹源,恶化合金性能.通过对一种Fe-Ni-Cr合金进行过时效后晶界上析出η相的研究发现,由于晶界η相与合金基体保持共格关系,η相对合金的室温性能影响不大;并且在高温变形条件下η相形成凸起,阻碍晶界滑动,减小在晶角处的应力集中,从而提高合金的高温塑性.断口扫描电镜观察表明,晶界η相的析出使合金高温断裂方式由原来的沿晶脆性断裂转变为穿晶韧窝状断裂.通过在合金中添加Nb,可以在晶界上析出更为弥散的η相,从而使得合金在高温下获得相当高的塑性. 展开更多
关键词 fe-Ni—Cr合金 η相 共格 晶界滑动 高温塑性
下载PDF
Fe-Cr合金晶界偏析及辐照加速晶界偏析的相场模拟 被引量:3
8
作者 杨朝曦 柳文波 +5 位作者 张璁雨 贺新福 孙正阳 贾丽霞 师田田 恽迪 《物理学报》 SCIE EI CAS CSCD 北大核心 2021年第11期198-207,共10页
基于WBM相场模型对热力学条件和辐照条件下Fe-Cr合金晶界处Cr元素偏析行为进行了模拟.模拟结果表明温度对Fe-Cr合金晶界处Cr元素的偏析有很大影响:当温度低于500℃时,晶界处的偏析量很小;而当温度高于500℃时晶界处的偏析量增加明显.基... 基于WBM相场模型对热力学条件和辐照条件下Fe-Cr合金晶界处Cr元素偏析行为进行了模拟.模拟结果表明温度对Fe-Cr合金晶界处Cr元素的偏析有很大影响:当温度低于500℃时,晶界处的偏析量很小;而当温度高于500℃时晶界处的偏析量增加明显.基体中Cr元素含量对晶界Cr元素的相对偏析量也有显著影响:随着基体中Cr元素含量的增加,相同模拟条件下晶界处Cr元素的相对浓度增量降低.辐照条件下,晶界处Cr元素的相对偏析量比热力学条件下的相对偏析量有明显增加;随着辐照剂量率的提高,晶界中心处Cr元素浓度增量变大;相同辐照条件下,随着Cr元素含量的增加,晶界处Cr元素的相对浓度增量也降低. 展开更多
关键词 相场模拟 fe-CR合金 晶界偏析 辐照加速扩散
下载PDF
Sm(Co,Cu,Fe,Zr)_z磁体畴壁钉扎的二维微磁学研究
9
作者 唐军 彭斌 +4 位作者 张文旭 张万里 蒋洪川 杨仕清 陈志川 《磁性材料及器件》 CAS CSCD 2005年第6期21-23,共3页
Sm(Co,Cu,Fe,Zr)z磁体中的畴壁钉扎研究一直是磁学领域中的关注点。本文首先建立了Sm(Co,Cu,Fe,Zr)z磁体畴壁钉扎的二维微磁学模型,然后利用微磁学计算了胞壁相的物理参数对畴壁钉扎的影响。计算结果表明,只有合适的胞壁相厚度和磁晶各... Sm(Co,Cu,Fe,Zr)z磁体中的畴壁钉扎研究一直是磁学领域中的关注点。本文首先建立了Sm(Co,Cu,Fe,Zr)z磁体畴壁钉扎的二维微磁学模型,然后利用微磁学计算了胞壁相的物理参数对畴壁钉扎的影响。计算结果表明,只有合适的胞壁相厚度和磁晶各向异性常数才能获得高的钉扎场。 展开更多
关键词 Sm(Co Cu fe Zr)2磁体 畴壁 钉扎场 微磁学 胞壁相
下载PDF
Effects of temperature on hydrostatic pressure-induced FE-AFE phase transition in PbLa(Zr,Sn,Ti)O_3 ceramics
10
作者 XU Zhuo, FENG Yujun, ZHENG Shuguang, JIN An, WANG Fanglin & YAO XiElectronic Materials Research Laboratory (EMRL), Xi’an Jiaotong University, Xi’an 710049, China 《Chinese Science Bulletin》 SCIE EI CAS 2001年第18期1574-1578,共5页
Hydrostatic pressure-induced ferroelectric-antiferroelectric (FE-AFE) phase transition and the pressure dependence of dielectric properties in La-doped Pb(Zr,Sn, Ti)O3 ceramics were researched; the effects of temperat... Hydrostatic pressure-induced ferroelectric-antiferroelectric (FE-AFE) phase transition and the pressure dependence of dielectric properties in La-doped Pb(Zr,Sn, Ti)O3 ceramics were researched; the effects of temperature on hydrostatic pressure-induced FE-AFE phase transition and dielectric properties of the samples were studied. It was found that the temperature made the FE-AFE phase transition pressure decrease, and there existed the behavior of dielectric frequency dispersion and phase transition diffusion in the dielectric-pressure spectrum. These phenomena were very useful to enrich and develop the knowledge on the diffused phase transition behavior of polycomponent relaxor ferroelectric. 展开更多
关键词 HYDROSTATIC PRESSURE PRESSURE-INDUCED phase TRANSITION fe-afe phase TRANSITION dielectric-pressure spectrum.
原文传递
Microstructure of explosively compacted Nd-Fe-B magnet by TEM
11
作者 敖琪 刘薇 +1 位作者 曹力军 吴建生 《中国有色金属学会会刊:英文版》 CSCD 2005年第2期468-472,共5页
The microstructure of an explosively compacted Nd-Fe-B permanent magnet(Nd-Fe-B) was investigated by means of TEM and XRD. It is shown that there are three kinds of phases: Nd2Fe14B matrix phase, O-rich phases and N... The microstructure of an explosively compacted Nd-Fe-B permanent magnet(Nd-Fe-B) was investigated by means of TEM and XRD. It is shown that there are three kinds of phases: Nd2Fe14B matrix phase, O-rich phases and Nd-rich phase with different structures and compositions in the magnet. The hard magnetic phase Nd2Fe14B is tetragonal, which lattice parameters are determined to be a=0.88 nm and c=1.22 nm. The O-rich phase locates at the grain boundaries and the triple junctions has fcc structure whose lattice parameter is a=0.559 nm. A dislocation is observed in this phase. It is also found that a large number of the block-shaped Nd-rich phases with hcp structure are embedded in the Nd2Fe14B matrix or at grain boundary. Their lattice parameters are determined to be a=0.395 nm and c=0.628 nm. 展开更多
关键词 边界相 微结构 钕-铁-硼永磁材料 爆炸压实工艺
下载PDF
Nd-Fe-B速凝合金晶界相组成与组织结构研究
12
作者 李彦儒 李安华 +1 位作者 冯海波 李卫 《中国稀土学报》 EI CAS CSCD 北大核心 2024年第2期236-244,I0002,共10页
钕铁硼烧结磁体中的晶界相组成、微结构及化学成分对其矫顽力有重要的影响,为了阐明钕铁硼烧结磁体中晶界相组成和微观组织结构的演变机制,有必要对其先驱体材料Nd-Fe-B速凝合金片中晶界富Nd相的相组成和微结构特点进行研究。采用速凝... 钕铁硼烧结磁体中的晶界相组成、微结构及化学成分对其矫顽力有重要的影响,为了阐明钕铁硼烧结磁体中晶界相组成和微观组织结构的演变机制,有必要对其先驱体材料Nd-Fe-B速凝合金片中晶界富Nd相的相组成和微结构特点进行研究。采用速凝工艺制备Nd-Fe-B速凝合金片,重点对速凝合金的晶界区域进行TEM研究。研究发现:在富Nd三角晶界存在两种衬度明显不同的区域,衬度均匀一致的区域为非晶微晶相,在衬度明暗对比的区域发现有双六方结构的Nd相(dhcp-Nd)、低熔点共晶相"Nd+Nd_(2)Fe_(14)B"和和少量非晶微晶相存在。晶界线扫描结果表明,晶界区域的Nd:Fe原子比并非恒定值,晶界非晶微晶区的Fe含量较高,其Fe含量平均值大于60%(原子分数);而晶界晶化区的成分波动较大,这可能是因为该区域是dhcp-Nd相、"Nd+Nd_(2)Fe_(14)B"共晶相以及少量非晶微晶相的混合物。在钕铁硼合金的晶界处普遍存在非晶相,是因为Nd-Fe-B合金体系属于深共晶体系,合金熔液在冷却过程中提早凝固,无序状态亚稳到室温造成的。 展开更多
关键词 Nd-fe-B速凝合金 晶界 相组成 组织结构
原文传递
掺La的锆锡钛酸铅陶瓷制备及介电性能 被引量:3
13
作者 张崇辉 王晓娟 朱长军 《纺织高校基础科学学报》 CAS 2016年第1期77-81,共5页
锆锡钛酸铅(Pb(Zr,Sn,Ti)O3)系列陶瓷具有优异的铁电、压电等性能,为制备高质量的陶瓷材料,采用传统的氧化物固相烧结工艺,制备了一组镧(La)元素微量掺杂的锆锡钛酸铅陶瓷,并对样品的铁电和介电性能进行测试表征.结果表明,所采用的制备... 锆锡钛酸铅(Pb(Zr,Sn,Ti)O3)系列陶瓷具有优异的铁电、压电等性能,为制备高质量的陶瓷材料,采用传统的氧化物固相烧结工艺,制备了一组镧(La)元素微量掺杂的锆锡钛酸铅陶瓷,并对样品的铁电和介电性能进行测试表征.结果表明,所采用的制备工艺良好,成瓷好,4组陶瓷样品的组分位于铁电/反铁电相界附近,铁电相和反铁电相共存. 展开更多
关键词 掺La的锆锡钛酸铅陶瓷 铁电/反铁电相界 介电性能
下载PDF
组分变化对La掺杂PZST反铁电陶瓷电性能的影响 被引量:1
14
作者 杨同青 刘鹏 +2 位作者 徐卓 张良莹 姚熹 《压电与声光》 CAS CSCD 北大核心 1998年第3期196-198,共3页
研究了La掺杂PZST反铁电陶瓷Zr∶Sn比的变化对电性能的影响。随着Zr∶Sn比的增加,开关电场EAFE-FE减小,回滞ΔE增大,峰值介电常数εmax增加并且变得尖锐,铁电-反铁电相变温度TFE-AFE和居里温度T... 研究了La掺杂PZST反铁电陶瓷Zr∶Sn比的变化对电性能的影响。随着Zr∶Sn比的增加,开关电场EAFE-FE减小,回滞ΔE增大,峰值介电常数εmax增加并且变得尖锐,铁电-反铁电相变温度TFE-AFE和居里温度TC升高。 展开更多
关键词 反铁电陶瓷 相变 电场诱导相变 PZST陶瓷 电性能
下载PDF
La掺杂PZST反铁电陶瓷电场诱导热释电现象 被引量:1
15
作者 杨同青 刘鹏 +2 位作者 徐卓 张良莹 姚熹 《压电与声光》 CAS CSCD 北大核心 1998年第5期350-353,共4页
研究了La掺杂PZST反铁电陶瓷在不同偏置电场下的场诱热释电特性。在0~120°C温度范围内,热释电的峰值和峰位可以用电场的大小来控制,热释电系数达到10-7C/cm2·K。
关键词 相变 电场诱导相变 热释电 电畴 PZST
下载PDF
碳、镍元素对铁-锰合金的阻尼性能与相变行为的影响 被引量:2
16
作者 李宁 胥永刚 +2 位作者 于学勇 邹红 邱绍宇 《机械工程材料》 CAS CSCD 北大核心 2006年第3期8-10,共3页
应用倒扭摆内耗仪、热机械分析仪和光学显微镜研究了碳和镍对铁-锰基减振合金γ→ε转变行为和阻尼性能影响。结果表明:碳增加γ→ε相变的阻力,降低合金的M_s温度,减少合金中ε马氏体的数量;碳的钉扎作用能够使合金中γ/ε相界面的... 应用倒扭摆内耗仪、热机械分析仪和光学显微镜研究了碳和镍对铁-锰基减振合金γ→ε转变行为和阻尼性能影响。结果表明:碳增加γ→ε相变的阻力,降低合金的M_s温度,减少合金中ε马氏体的数量;碳的钉扎作用能够使合金中γ/ε相界面的滑移性能变差,从而恶化了合金的阻尼性能。镍降低了合金的相变温度,但不会对合金阻尼性能产生不利影响。 展开更多
关键词 阻尼性能 相变γ/ε相界 铁一锰合金
下载PDF
高性能Cu-Fe合金薄带材及其短流程制备技术
17
作者 孙文博 吴诗睿 +2 位作者 吴天模 张元祥 袁国 《沈阳工业大学学报》 CAS 2024年第4期403-408,共6页
为了解决Cu-Fe合金常规制备流程中重力分层的问题,利用铸轧工艺的亚快速凝固特点抑制其液相分离,并结合Marangoni效应及热泳力的耦合作用合理调控铸轧参数,获得厚度为2.2~2.4 mm、铁磁相尺寸和分布可控的Cu-20%Fe和Cu-30%Fe带材。通过... 为了解决Cu-Fe合金常规制备流程中重力分层的问题,利用铸轧工艺的亚快速凝固特点抑制其液相分离,并结合Marangoni效应及热泳力的耦合作用合理调控铸轧参数,获得厚度为2.2~2.4 mm、铁磁相尺寸和分布可控的Cu-20%Fe和Cu-30%Fe带材。通过金相与EBSD分析确定铸带形成了Cu相-富Fe相-Cu相的“三明治”层状复合结构,其中Cu-20%Fe铸带中的Fe相分布更为均匀,且EBSD分析结果表明凝固层中形成了大量的低能晶界,如Σ1和Σ3等。将Cu-20%Fe合金从2.4 mm冷轧至0.4 mm,在不同温度下进行热处理后继续冷轧至0.12 mm。结果表明:450℃热处理对轧板性能更好,导电率超过50%IACS,抗拉强度超过600 MPa,均匀伸长率达到7.5%,饱和磁化强度超过4.24×10^(5)A/m。 展开更多
关键词 Cu-fe合金 薄带材 亚稳液相分离 双辊铸轧 亚快速凝固 Marangoni迁移 低能晶界 Σ3晶界
下载PDF
锆钛酸铅95/5薄膜的介电性能与弛豫特征
18
作者 王英 张超 +1 位作者 迟媛媛 余大书 《武汉工程大学学报》 CAS 2012年第3期42-44,50,共4页
采用溶胶-凝胶法制备锆钛酸铅95/5(PZT95/5)薄膜,通过分析介电温度谱、介电频谱研究薄膜的介电性能.研究结果表明:介电常数-温度曲线ε(T)的相变峰随着频率的增加而逐渐变得平坦.同时,介电常数倒数与温度曲线ε-1(T)在高频不符合居里外... 采用溶胶-凝胶法制备锆钛酸铅95/5(PZT95/5)薄膜,通过分析介电温度谱、介电频谱研究薄膜的介电性能.研究结果表明:介电常数-温度曲线ε(T)的相变峰随着频率的增加而逐渐变得平坦.同时,介电常数倒数与温度曲线ε-1(T)在高频不符合居里外斯定律;采用普适弛豫定律公式,对不同温度下的介电频谱曲线ε(f)进行拟合,得到弥散系数随着温度的变化曲线,该曲线在铁电-顺电转变以及反铁电-铁电转变这两个特征温度附近出现异常,结合材料反铁电-铁电-顺电相变的微观结构变化规律对此现象进行了讨论. 展开更多
关键词 溶胶-凝胶 反铁电-铁电相变 介电谱 普适弛豫定律
下载PDF
6016铝合金板材微观组织对包边性能的影响 被引量:2
19
作者 刘晨光 王家毅 +3 位作者 石宪柱 刘晓滕 迟蕊 马钰 《轻合金加工技术》 CAS 2021年第9期33-38,45,共7页
利用金相显微镜、扫描电镜与透射电镜等手段对6016铝合金汽车车身外板包边试验样品进行微观组织分析。结果表明,当板材表面、纵截面与横截面晶粒组织均匀、细小(30μm以下)时,有助于加工变形过程中晶粒之间协调变形及应力传递,可保证包... 利用金相显微镜、扫描电镜与透射电镜等手段对6016铝合金汽车车身外板包边试验样品进行微观组织分析。结果表明,当板材表面、纵截面与横截面晶粒组织均匀、细小(30μm以下)时,有助于加工变形过程中晶粒之间协调变形及应力传递,可保证包边产品的表面质量;控制合金中含铁相尺寸能减少板材乳制后大尺寸粒子间残存的空洞,有助于降低包边产品开裂的可能性;干净无弥散相析出的晶界可减少包边过程中产生的应力集中。 展开更多
关键词 6016铝合金板 微观组织 包边 晶粒 含铁相 晶界
下载PDF
快速凝固Fe-6.5%Si合金有序结构及力学性能研究 被引量:5
20
作者 李慧 梁永锋 +2 位作者 贺睿琦 林均品 叶丰 《金属学报》 SCIE EI CAS CSCD 北大核心 2013年第11期1452-1456,共5页
通过单辊快速凝固的方法制备出宽度为20 mm,厚度为35—50μm,连续成卷的Fe-6.5%Si合金薄带.与普通铸造方法相比,用快速凝固方法得到的Fe-6.5%Si合金具有良好的室温塑性.采用TEM及XRD研究了普通铸锭和快凝薄带的有序化结构和微观组织,并... 通过单辊快速凝固的方法制备出宽度为20 mm,厚度为35—50μm,连续成卷的Fe-6.5%Si合金薄带.与普通铸造方法相比,用快速凝固方法得到的Fe-6.5%Si合金具有良好的室温塑性.采用TEM及XRD研究了普通铸锭和快凝薄带的有序化结构和微观组织,并计算了这2种制备条件下B2有序相的长程有序度.结果表明,普通铸造方法得到的Fe-6.5%Si合金含有大量的B2和D0_3有序相,且有序度较高.而快凝薄带晶粒细小,快的冷却速率有效地抑制了D0_3有序相的形成,同时也降低了B2相的生长速度,使合金有序度较低,从而使带材塑性得到明显改善. 展开更多
关键词 fe-6 5%Si合金 快速凝固 有序相 反相畴界 TEM
原文传递
上一页 1 2 下一页 到第
使用帮助 返回顶部