The flexural behavior of eight FRP （ fiber reinforced polymer） strengthened RC （reinforced concrete） beams with different steel corrosion rates are numerically studied by Ansys finite element software. The influen...The flexural behavior of eight FRP （ fiber reinforced polymer） strengthened RC （reinforced concrete） beams with different steel corrosion rates are numerically studied by Ansys finite element software. The influences of the corrosion rate on crack pattern, failure mechanism, ultimate strength, ductility and deformation capacity are also analyzed. Modeling results show that the beams with low corrosion rates fail by the crushing of the concrete in the compression zone. For the beams with medium corrosion rates, the bond slip between the concrete and the longitudinal reinforcement occurs after steel yielding, and the beams finally fail by the debonding of the FRP plates. For the beams with high corrosion rates, the bond slip occurs before steel yielding, and the beams finally fail by the crushing of the concrete in the compression zone. The higher the corrosion rates of the longitudinal reinforcement, the more the carrying capacity of FRP strengthened RC beams reduces. The carrying capacity of RCB-1 （the corrosion rate is 0） is 115 kN, and the carrying capacity of RCB-7 （the corrosion rate is 20% ） is 42 kN. The deformation capacity of FRP strengthened corroded RC beams is higher than that of FRP strengthened uucorroded RC beams. The ultimate deflection of RCB-1 and RCB-7 are 20 mm and 35 nun, respectively, and the ultimate deflection of RCB-5 （the corrosion rate is 10% ） reaches 60 ilUn.展开更多
Strengthening of RC structures with externally bonded FRP （fiber reinforced polymers） has become an important challenge in civil engineering. Epoxy is the main bonding agent used so far, but in the case of a fire, i...Strengthening of RC structures with externally bonded FRP （fiber reinforced polymers） has become an important challenge in civil engineering. Epoxy is the main bonding agent used so far, but in the case of a fire, it is subjected to complete loss of his bonding capabilities. Mineral based composites strengthening systems consist of FRPs and a cementitious bonding agent which form a repair or strengthening system that is more compatible with the concrete substrata, and roved its efficiency. The current research introduces the use of a special cementitious material ＂Grancrete＂ as a bonding agent. Test results of 32 T-section RC beams strengthened with various FRG （fiber reinforced Grancrete） strengthening systems are presented. The results demonstrated that most of the specimens were likely to fail by debonding of the FRP from the concrete either at the ends or at intermediate flexural cracks. This paper presents an in-depth study aimed at the development of a better understanding of debonding failures in RC beams strengthened with externally bonded FRP systems. Different analytical models, published in the literature for plate end debonding, are reviewed and compared to test results. The results also demonstrated that when using U-wraps, the specimens were likely to fail by FRP sheet rupture.展开更多
基金The National Natural Science Foundation of China(No.51278118)Scientific and Technological Research Project of Ministry of Education(No.113028A)+1 种基金the Natural Science Foundation of Jiangsu Province(No.BK2012756)the Program for Special Talents in Six Fields of Jiangsu Province(No.2011-JZ-010)
文摘The flexural behavior of eight FRP （ fiber reinforced polymer） strengthened RC （reinforced concrete） beams with different steel corrosion rates are numerically studied by Ansys finite element software. The influences of the corrosion rate on crack pattern, failure mechanism, ultimate strength, ductility and deformation capacity are also analyzed. Modeling results show that the beams with low corrosion rates fail by the crushing of the concrete in the compression zone. For the beams with medium corrosion rates, the bond slip between the concrete and the longitudinal reinforcement occurs after steel yielding, and the beams finally fail by the debonding of the FRP plates. For the beams with high corrosion rates, the bond slip occurs before steel yielding, and the beams finally fail by the crushing of the concrete in the compression zone. The higher the corrosion rates of the longitudinal reinforcement, the more the carrying capacity of FRP strengthened RC beams reduces. The carrying capacity of RCB-1 （the corrosion rate is 0） is 115 kN, and the carrying capacity of RCB-7 （the corrosion rate is 20% ） is 42 kN. The deformation capacity of FRP strengthened corroded RC beams is higher than that of FRP strengthened uucorroded RC beams. The ultimate deflection of RCB-1 and RCB-7 are 20 mm and 35 nun, respectively, and the ultimate deflection of RCB-5 （the corrosion rate is 10% ） reaches 60 ilUn.
文摘Strengthening of RC structures with externally bonded FRP （fiber reinforced polymers） has become an important challenge in civil engineering. Epoxy is the main bonding agent used so far, but in the case of a fire, it is subjected to complete loss of his bonding capabilities. Mineral based composites strengthening systems consist of FRPs and a cementitious bonding agent which form a repair or strengthening system that is more compatible with the concrete substrata, and roved its efficiency. The current research introduces the use of a special cementitious material ＂Grancrete＂ as a bonding agent. Test results of 32 T-section RC beams strengthened with various FRG （fiber reinforced Grancrete） strengthening systems are presented. The results demonstrated that most of the specimens were likely to fail by debonding of the FRP from the concrete either at the ends or at intermediate flexural cracks. This paper presents an in-depth study aimed at the development of a better understanding of debonding failures in RC beams strengthened with externally bonded FRP systems. Different analytical models, published in the literature for plate end debonding, are reviewed and compared to test results. The results also demonstrated that when using U-wraps, the specimens were likely to fail by FRP sheet rupture.
