This paper presents an experimental study on the behavior of circular concrete columns reinforced by BFRP-PVC tubes under uniaxial loading.A total of six specimens were prepared and tested under uniaxial loading.The m...This paper presents an experimental study on the behavior of circular concrete columns reinforced by BFRP-PVC tubes under uniaxial loading.A total of six specimens were prepared and tested under uniaxial loading.The main parameters varied in the tests were strengthening ratio and strengthening approach of BFRP.The performance,such as failure modes,ultimate bearing capacity and stress-strain curves,was investigated in details and a formula was proposed to predict the compressive ultimate strength.The results show that this kind of confined columns obviously improves the ultimate bearing capacity,and the ultimate bearing capacity increases with the strengthening layers.The formula proposed is applicable and efficient for prediction of the ultimate bearing capacity as well.展开更多
In this article,the experimental and finite element analysis is utilized to investigate the quasi-static compression features of sandwich constructions built with tapered tubes.3D printing technology was utilized to c...In this article,the experimental and finite element analysis is utilized to investigate the quasi-static compression features of sandwich constructions built with tapered tubes.3D printing technology was utilized to create the hollow centers of the tapering tubes,with and without corrugations.The results demonstrate that the energy absorption(EA)and specific energy absorption(SEA)of the single corrugated tapered tube sandwich are 51.6% and 19.8% higher,respectively,than those of the conical tube sandwich.Furthermore,the results demonstrate that energy absorbers can benefit from corrugation in order to increase their efficiency.Additionally,the tapered corrugated tubes'resistance to oblique impacts was studied.Compared to a straight tube,the tapered tube is more resistant to oblique loads and has a lower initial peak crushing force(PCF),according to numerical simulations.After conducting a parametric study,it was discovered that the energy absorption performance of the sandwich construction is significantly affected by the amplitude,number of corrugations,and wall thickness.EA and SEA of DTS with corrugation number of 8 increased by 17.4%and 29.6%,respectively,while PCF decreased by 9.2% compared to DTS with corrugation number of 10.展开更多
Aluminum alloy thin-walled structures are widely used in the automotive industry due to their advantages related to light weight and crashworthiness.They can be produced at room temperature by the electrohydraulic for...Aluminum alloy thin-walled structures are widely used in the automotive industry due to their advantages related to light weight and crashworthiness.They can be produced at room temperature by the electrohydraulic forming process.In the present study,the influence of the related parameters on the forming quality of a 6063 aluminum alloy sinusoidal corrugation tube has been assessed.In particular,the orthogonal experimental design(OED)and central composite design(CCD)methods have been used.Through the range analysis and variance analysis of the experimental data,the influence degree of wire diameter(WD)and discharge energy(DE)on the forming quality was determined.Multiple regression analysis was performed using the response surface methodology.A prediction model for the attaching-die state coefficient was established accordingly.The following optimal arrangement of parameters was obtained(WD=0.759 mm,DE=2.926 kJ).The attaching-die state coefficient reached the peak value of 0.001.Better optimized wire diameter and discharge energy for a better attaching-die state could be screened by CCD compared with OED.The response surface method in CCD was more suitable for the design and optimization of the considered process parameters.展开更多
Recently, tragic tailings dam collapses in Brazil have caused deaths and major destruction and the need to develop technologies capable of preventing damage to people and the environment. Brazilian tailings dams are i...Recently, tragic tailings dam collapses in Brazil have caused deaths and major destruction and the need to develop technologies capable of preventing damage to people and the environment. Brazilian tailings dams are in a situation of uncertainty due to new legislation that even requires decommissioning, an activity that involves many problems and where the risk of failure is the main one. An impact containment structure downstream of these dams can be effective and geotextile tubes, in a new approach, have emerged as an option with advantages in terms of execution, costs and safety. The technology is versatile and can bring many benefits such as the reuse of tailings or filling with low-energy or reused materials. In this research, geotextile tubes were tested as free containment barriers, experiencing impacts in reduced models. The safety factor for the stability of the structure was constructed using an equation which is the ratio between the self-weight of the barrier structure and its coefficient of static friction and the impact pressure, where the data showed an adequate correlation which suggests the viability of mitigating risks.展开更多
Introduction: Fallopian diseases are often implicated in female infertility. Several radiological and surgical explorations have been proposed in order to evaluate the severity of lesions found in utero-adnexal pathol...Introduction: Fallopian diseases are often implicated in female infertility. Several radiological and surgical explorations have been proposed in order to evaluate the severity of lesions found in utero-adnexal pathology. Among tools that are used to investigate such pathologies, we have ultrasound, hysterosalpingography and endoscopy. But, in many developing countries like Cameroon, the usage of endoscopy in gynecology is not yet known by many practicians. The objective of our study was to show the interest of endoscopy in the diagnosis of fallopian tube pathologies. Methodology: We conducted a cross-sectional and descriptive study from March 1<sup>st</sup>, 2017 to May 31<sup>st</sup>, 2017 at the Gyneco-Obstetrics and Pediatric department of our Hospital. We included all women who presented infertility and underwent ultrasound, hysterosalpingography (HSG) and endoscopy at the Yaoundé Gyneco-obstetrics Hospital. We analyzed epidemiological parameters, clinics, ultrasound, hysterosalpingography and endoscopic finding. We used Cohen’s Kappa test to determine the correlation between HSG/endoscopy and ultrasound/endoscopy in the diagnosis of fallopian tube pathologies. The threshold was significant for a K-value > 0.20. Results: We got a sample of 156 women;the mean age was 32.6 ± 4.5 years. The Secondary infertility dominated in 66.7% of cases;31.1% of women presented a past medical history of sexually transmitted infections and 41.7% did abortions before. Endoscopic lesions were dominated by a fallopian obstruction in 54.5% of cases, 8.3% of adhesions, 33.9% of women presented uterine myomas, 37.8% of ovarian cysts and 1.3% of pelvic endometriosis. The K-values between HSG and endoscopy for distal and proximal tube obstructions were significant with respective thresholds of 0.25 and 0.30. The K-value between ultrasound and endoscopy was not significant with a threshold of 0.015 for the tubal hydrosalpinx. Conclusion: Endoscopy assessment appears as the most efficient tool to investigate fallopian tube diseases.展开更多
Arabinogalactan proteins(AGPs)are widely distributed in the plant kingdom and play a vital role during the process of plant sexual reproduction.In this study,we performed a comprehensive identification of the PbrAGPs ...Arabinogalactan proteins(AGPs)are widely distributed in the plant kingdom and play a vital role during the process of plant sexual reproduction.In this study,we performed a comprehensive identification of the PbrAGPs expressed in pear pollen and further explored their influences on pollen tube growth.Among the 187 PbrAGPs that were found to be expressed in pear pollen tubes,38 PbrAGPs were specifically expressed in pollen according to the RNA-seq data.The PbrAGPs were divided into two groups of highly expressed and specifically expressed in pear pollen.We further tested their expression patterns using RT-PCR and RT-qPCR.Most of the PbrAGPs were expressed in multiple tissues and their expression levels were consistent with reads per kilobase per million map reads(RPKM)values during pollen tube growth,implying that PbrAGPs might be involved in the regulation of pear pollen tube growth.We also constructed phylogenetic trees to identify the functional genes in pear pollen tube growth.Therefore,19 PbrAGPs(PbrAGP1 to PbrAGP19)were selected to test their influences on pollen tube growth.Recombinant proteins of the 19 PbrAGP-His were purified and used to treat pear pollen,and 11 of the PbrAGP-His recombinant proteins could promote pear pollen tube growth.Additionally,pollen tube growth was inhibited when the expression levels of PbrAGP1 and PbrAGP5 were knocked down using an antisense oligonucleotide assay.PbrAGP1 and PbrAGP5 were localized in the plasma membrane and might not alter the distribution of pectin in the pollen tube.In summary,this study identified the PbrAGPs expressed in pear pollen and lays the foundation for further exploring their functions in pollen tube growth.展开更多
Protecting occupants or payloads in crashes and blasts is of utmost importance in both moving and immobile structures.One way of achieving this is by using a sacrificial energy absorber.Composite tubes have been studi...Protecting occupants or payloads in crashes and blasts is of utmost importance in both moving and immobile structures.One way of achieving this is by using a sacrificial energy absorber.Composite tubes have been studied as potential energy absorbers due to their ability to fail progressively under axial compression.In this study,the energy absorption capability of these tubes is enhanced by adding hollow glass particles to the matrix.Drop-weight tests are performed on composite tubes,and a digital image correlation(DIC)-based technique is used to capture their load-displacement behaviour.This eliminates the use of electronic data acquisition systems,load cells,and accelerometers.The load-displacement curves of the tubes are obtained from the DIC-based technique and examined to understand their crushing behaviour.Although the mean crush load shows a drop,an increase in crush length is noticed.The specific energy absorbed by the tubes improves with an increase in GMB volume fraction.The addition of 0.1,0.2,0.3 and 0.4 vol fractions of GMB results in the specific energy absorption increasing by6.6%,14.7%,24%and 36.6%,respectively,compared to neat glass fibre-epoxy tubes.Visual examination of the tubes and comparison with tubes subject to quasi-static compression is also performed.展开更多
The thermal transmission coefficient for a micro-ribbed tube has been determined using theoretical relationships and the outcomes of such calculations have been compared with experiments conducted using a R1234yf refr...The thermal transmission coefficient for a micro-ribbed tube has been determined using theoretical relationships and the outcomes of such calculations have been compared with experiments conducted using a R1234yf refrigerant undergoing condensation.In particular four theoretical single-phase flow and three multi-phase flow models have been used in this regard.The experimental results show that:the Oliver et al.criterion equation overestimates the experimental results as its accuracy is significantly affected by the specific conditions realized inside micro-fin tubes;the Miyara et al.criterion equation prediction error is less than 15%;the Cavallini et al.approach gives the highest prediction accuracy;the Goto et al.model overestimates the test data.Such results are critically discussed and some indications for the improvement of such models are provided.展开更多
AIM:To evaluate the pathogens in cultured Jones tubes used in lacrimal bypass surgery according to the postoperative periods and to obtain data for the prevention of infection of functional lacrimal stent invention.ME...AIM:To evaluate the pathogens in cultured Jones tubes used in lacrimal bypass surgery according to the postoperative periods and to obtain data for the prevention of infection of functional lacrimal stent invention.METHODS:Totally 71 patients(81 eyes)who underwent the removal of Jones tubes were enrolled in study.All the removed Jones tubes were cultured for bacterial and fungal identification and tested for bacterial antibiotic sensitivity.The results were analyzed according to the duration of the inserted Jones tube after lacrimal bypass surgery.RESULTS:Of the 81 eyes,bacteria were isolated from 69 eyes(85.2%)and fungi from 6 eyes(7.4%).Among 69 eyes,40.6% showed Staphylococcus aureus(S.aureus),11.6% were Pseudomonas aeruginosa(P.aeruginosa).Gram-positive bacteria were isolated more than Gramnegative bacteria,but Gram-negative bacteria showed a higher incidence in the Jones tube implanted for over 10y(P=0.035).The antibiotic sensitivity test showed that 46.4% of S.aureus were resistant to oxacillin.In terms of antibiotics commonly used in ocular clinical practice,vancomycin was sensitive to S.aureus and Streptococcus pneumoniae(S.pneumoniae),amikacin responded to P.aeruginosa and Proteus mirabilis(P.mirabilis).Trimethoprim/sulfamethoxazole(TMP/SMX)was all sensitive to S.aureus,S.pneumoniae and P.mirabilis except P.aeruginosa.CONCLUSION:S.aureus is the most commonly found organism in the Jones tube after lacrimal bypass surgery,and 46.4% of them are methicillin-resistant S.aureus(MRSA),sensitive to vancomycin.Especially,P.mirabilis responded with amikacin is dominantly detected in the Jones tubes implanted for more than 10y.展开更多
Introduction: Endotracheal suction plays a crucial role in the management of mechanically ventilated patients. This study aims to evaluate the clinical effectiveness and safety of suction tubes with markings in mechan...Introduction: Endotracheal suction plays a crucial role in the management of mechanically ventilated patients. This study aims to evaluate the clinical effectiveness and safety of suction tubes with markings in mechanically ventilated pediatric patients. Materials and Methods: A randomized assignment was carried out on a cohort of 52 pediatric patients who underwent mechanical ventilation in the Pediatric Intensive Care Unit at the Third Affiliated Hospital of Sun Yat-sen University, covering the period from January 2022 to December 2022. These patients were divided into two groups: an improved group (n = 26) utilizing marked suction tubes, and a regular group (n = 26) employing conventional suction tubes. The objective of our study was to evaluate the clinical effectiveness of marked suction tubes. Results: The effects of the improved group on the vital signs of children undergoing mechanical ventilation were small and statistically significant compared with the regular group (p < 0.05). Additionally, the improved group exhibited a reduced frequency of sputum suction, shorter mechanical ventilation duration, and fewer days of hospitalization in the PICU compared to the regular group during the ventilation period. Notably, the difference in the duration of PICU hospitalization was statistically significant (p < 0.05). Moreover, the incidence of adverse reactions in the improved group was notably lower, with statistically significant differences observed in airway mucous membrane damage and irritating cough when compared to the regular group (p < 0.05). Conclusion: The utilization of marked suction tubes provides clinical nurses with clear guidance for performing suctioning with ease, efficiency and safety. Consequently, advocating for the widespread implementation of marked suction tubes in clinical practice is a commendable pursuit.展开更多
Bubble and slurry bubble column reactors(BCRs/SBCRs)are used for various chemical,biochemical,and petro-chemical applications.They have several operational and maintenance advantages,including excellent heat and mass ...Bubble and slurry bubble column reactors(BCRs/SBCRs)are used for various chemical,biochemical,and petro-chemical applications.They have several operational and maintenance advantages,including excellent heat and mass transfer rates,simplicity,and low operating and maintenance cost.Typically,a catalyst is present in addition to biochemical processes where microorganisms are used to produce industrially valuable bio-products.Since most applications involve complicated gas-liquid,gas-liquid-solid,and exothermic processes,the BCR/SBCR must be equipped with heat-exchanging tubes to dissipate heat and control the reactor’s overall performance.In this review,past and very recent experimental and numerical investigations on such systems are critically dis-cussed.Furthermore,gaps to befilled and critical aspects still requiring investigation are identified.展开更多
Transition metal oxides are regarded as promising candidates of anode for next-generation lithium-ion batteries(LIBs)due to their ultrahigh theoretical capacity and low cost,but are restricted by their low conductivit...Transition metal oxides are regarded as promising candidates of anode for next-generation lithium-ion batteries(LIBs)due to their ultrahigh theoretical capacity and low cost,but are restricted by their low conductivity and large volume expansion during Li^(+)intercalation.Herein,we designed and constructed a structurally integrated 3D carbon tube(3D-CT)grid film with Mn_(3)O_(4)nanoparticles(Mn_(3)O_(4)-NPs)and carbon nanotubes(CNTs)filled in the inner cavity of CTs(denoted as Mn_(3)O_(4)-NPs/CNTs@3D-CT)as high-performance free-standing anode for LIBs.The Mn_(3)O_(4)-NPs/CNTs@3D-CT grid with Mn_(3)O_(4)-NPs filled in the inner cavity of 3D-CT not only afford sufficient space to overcome the damage caused by the volume expansion of Mn_(3)O_(4)-NPs during charge and discharge processes,but also achieves highly efficient channels for the fast transport of both electrons and Li+during cycling,thus offering outstanding electrochemical performance(865 mAh g^(-1)at 1 A g^(-1)after 300 cycles)and excellent rate capability(418 mAh g^(-1)at 4 A g^(-1))based on the total mass of electrode.The unique 3D-CT framework structure would open up a new route to the highly stable,high-capacity,and excellent cycle and high-rate performance free-standing electrodes for highperformance Li-ion storage.展开更多
The microstructure of the thin-walled tubes with high-strength aluminum alloy determines their final forming quality and performance. This type of tube can be manufactured by multi-pass hot power backward spinning pro...The microstructure of the thin-walled tubes with high-strength aluminum alloy determines their final forming quality and performance. This type of tube can be manufactured by multi-pass hot power backward spinning process as it can eliminate casting defects, refine microstructure and improve the plasticity of the tube. To analyze the microstructure distribution characteristics of the tube during the spinning process, a 3D coupled thermo-mechanical FE model coupled with the microstructure evolution model of the process was established under the ABAQUS environment. The microstructure evolution characteristics and laws of the tube for the whole spinning process were analyzed. The results show that the dynamic recrystallization is mainly produced in the spinning deformation zone and root area of the tube. In the first pass, the dynamic recrystallization phenomenon is not obvious in the tube. With the pass increasing, the trend of dynamic recrystallization volume percentage gradually increases and extends from the outer surface of the tube to the inner surface. The fine-grained area shows the states of concentration, dispersion, and re-concentration as the pass number increases. .展开更多
BACKGROUND Since its description in 1790 by Hunter,the nasogastric tube(NGT)is commonly used in any healthcare setting for alleviating gastrointestinal symptoms or enteral feeding.However,the risks associated with its...BACKGROUND Since its description in 1790 by Hunter,the nasogastric tube(NGT)is commonly used in any healthcare setting for alleviating gastrointestinal symptoms or enteral feeding.However,the risks associated with its placement are often underes-timated.Upper airway obstruction with a NGT is an uncommon but potentially life-threatening complication.NGT syndrome is characterized by the presence of an NGT,throat pain and vocal cord(VC)paralysis,usually bilateral.It is poten-tially life–threatening,and early diagnosis is the key to the prevention of fatal upper airway obstruction.However,fewer cases may have been reported than might have occurred,primarily due to the clinicians'unawareness.The lack of specific signs and symptoms and the inability to prove temporal relation with NGT insertion has made diagnosing the syndrome quite challenging.AIM To review and collate the data from the published case reports and case series to understand the possible risk factors,early warning signs and symptoms for timely detection to prevent the manifestation of the complete syndrome with life-threatening airway obstruction.METHODS We conducted a systematic search for this meta-summary from the database of PubMed,EMBASE,Reference Citation Analysis(https://www.referencecitation-analysis.com/)and Google scholar,from all the past studies till August 2023.The search terms included major MESH terms"Nasogastric tube","Intubation,Gastrointestinal","Vocal Cord Paralysis",and“Syndrome”.All the case reports and case series were evaluated,and the data were extracted for patient demographics,clinical symptomatology,diagnostic and therapeutic interventions,clinical course and outcomes.A datasheet for evaluation was further prepared.RESULTS Twenty-seven cases,from five case series and 13 case reports,of NGT syndrome were retrieved from our search.There was male predominance(17,62.96%),and age at presentation ranged from 28 to 86 years.Ten patients had diabetes mellitus(37.04%),and nine were hypertensive(33.33%).Only three(11.11%)patients were reported to be immunocompromised.The median time for developing symptoms after NGT insertion was 14.5 d(interquartile range 6.25-33.75 d).The most commonly reported reason for NGT insertion was acute stroke(10,37.01%)and the most commonly reported symptoms were stridor or wheezing 17(62.96%).In 77.78%of cases,bilateral VC were affected.The only treatment instituted in most patients(77.78%)was removing the NG tube.Most patients(62.96%)required tracheostomy for airway protection.But 8 of the 23 survivors recovered within five weeks and could be decannulated.Three patients were reported to have died.CONCLUSION NGT syndrome is an uncommon clinical complication of a very common clinical procedure.However,an under-reporting is possible because of misdiagnosis or lack of awareness among clinicians.Patients in early stages and with mild symptoms may be missed.Further,high variability in the presentation timing after NGT insertion makes diagnosis challenging.Early diagnosis and prompt removal of NGT may suffice in most patients,but a significant proportion of patients presenting with respiratory compromise may require tracheostomy for airway protection.展开更多
Thin-walled structures are widely used in cars due to their lightweight construction and energy-absorbing properties.However,issues such as high initial stress and lowenergy-absorbing efficiency arise.This study propo...Thin-walled structures are widely used in cars due to their lightweight construction and energy-absorbing properties.However,issues such as high initial stress and lowenergy-absorbing efficiency arise.This study proposes a novel energy-absorbing structure inwhich a straight tube is combinedwith a conical tube and a bamboo-inspired bulkhead structure is introduced.This configuration allows the conical tube to flip outward first and then fold together with the straight tube.This deformation mode absorbs more energy and less peak force than the conical tube sinking and flipping inward.Through finite element numerical simulation,the specific energy absorption capacity of the structure is increased by 26%compared to that of a regular circular cross-section tube.Finally,the impact resistance of the bionic straight tapered tube structure is further improved through multi-objective optimization,promoting the engineering application and lightweight design of hybrid cross-section tubes.展开更多
In this study,the extruded Mg-Zn-Mn-Ce-Ca alloy tube with a low compression anisotropy along the ED,45ED and TD was prepared.The effect of the second phases,initial texture and deformation behavior on this low mechani...In this study,the extruded Mg-Zn-Mn-Ce-Ca alloy tube with a low compression anisotropy along the ED,45ED and TD was prepared.The effect of the second phases,initial texture and deformation behavior on this low mechanical anisotropy was investigated.The results revealed that the alloy tube contains the high content(Mg1-xZnx)11Ce phase and the low content of Mg12Ce phase.These second phases are respectively incoherent and coherent with the Mg matrix,and their influence can be ignored.Additionally,the alloy tube exhibited a weak basal fiber texture,where the c-axis was aligned along the 0°∼30°tilt from TD to ED.Such a texture made the initial deformation(at 1.0%∼1.6%strain)of the three samples controlled by comparable basalslip.As deformation progressed(1.6∼9.0%strain),larger amounts of ETWs nucleated and gradually approached saturation in the three samples,re-orienting the c-axis to a 0°∼±30°deviation with respect to the loading directions.Meanwhile,the prismatic and pyramidal<c+a>slips replaced the dominant deformation progressively until fracture.Eventually,the similar deformation mechanisms determined by the weak initial texture in the three samples contribute to the comparable strain hardening rates,resulting in the low compressive anisotropy of the alloy tube.展开更多
In this paper, a novel efficient energy absorber with free inversion of a metal foam-filled circular tube(MFFCT) is designed, and the axial compressive behavior of the MFFCT under free inversion is studied analyticall...In this paper, a novel efficient energy absorber with free inversion of a metal foam-filled circular tube(MFFCT) is designed, and the axial compressive behavior of the MFFCT under free inversion is studied analytically and numerically. The theoretical analysis reveals that the energy is mainly dissipated through the radial bending of the metal circular tube, the circumferential expansion of the metal circular tube, and the metal filled-foam compression. The principle of energy conservation is used to derive the theoretical formula for the minimum compressive force of the MFFCT over free inversion under axial loading. Furthermore, the free inversion deformation characteristics of the MFFCT are analyzed numerically. The theoretical steady values are found to be in good agreement with the results of the finite element(FE) analysis. The effects of the average diameter of the metal tube, the wall thickness of the metal tube, and the filled-foam strength on the free inversion deformation of the MFFCT are considered. It is observed that in the steady deformation stage, the load-carrying and energy-absorbing capacities of the MFFCT increase with the increase in the average diameter of the metal tube, the wall thickness of the metal tube, or the filled-foam strength. The specific energy absorption(SEA) of free inversion of the MFFCT is significantly higher than that of the metal tube alone.展开更多
Background: Sudden sensorineural hearing loss(SSNHL) is a prevalent emergency in ear, nose, and throat practice. Previous studies have demonstrated that intratympanic steroid therapy(IST) can serve as a salvage treatm...Background: Sudden sensorineural hearing loss(SSNHL) is a prevalent emergency in ear, nose, and throat practice. Previous studies have demonstrated that intratympanic steroid therapy(IST) can serve as a salvage treatment for SSNHL after the failure of systemic steroid therapy(SST).Objective: This study aimed to analyze the efficacy of modified IST involving the insertion of a tympanic tube and gelfoam as a salvage treatment for patients with SSNHL, and to explore its associated factors.Methods: Totally, 74 patients who were aged 22–81 years with SSNHL were enrolled and allocated to either the control group(n = 25) or the treatment group(n = 49) based on their treatment modalities. All patients received SST lasting for at least 7 days. Subsequently, patients in the treatment group, after SST failure, underwent IST twice a week for 2–6 weeks, while the control group did not. Efficacy was assessed by the improvement in pure tone average at the affected frequency at the beginning and end of IST.Results: Hearing improvement in all patients after IST in the treatment group was 9.71 ± 14.84 dB, with significant improvement at affected frequencies(250-8000 Hz) compared with the control group(P < 0.05). The findings indicated the duration from the onset of SSNHL to the beginning of IST as an independent factor for pure tone average improvement after treatment(P = 0.002), whereas age, duration of SST, and time of IST were not(P > 0.05).Conclusion: The modified IST was demonstrated to be a safe and effective method as a salvage treatment for SSNHL. This study explored the efficacy of a modified IST approach, incorporating the utilization of tympanic tubes and gelfoam as key components. The findings underscore the advantages of gelfoam as a strategic drug carrier placed in the round window niche. By minimizing drug loss, extending action time, and increasing perilymph concentration, gelfoam enhances the therapeutic impact of IST, contributing to improved hearing outcomes in patients with SSNHL.展开更多
The radiant tube burner was modeled and analyzed by the numerical simulation method to investigate the influence factors and rules of NO_(x) emissions in a W-type radiant tube.These factors,which include air preheatin...The radiant tube burner was modeled and analyzed by the numerical simulation method to investigate the influence factors and rules of NO_(x) emissions in a W-type radiant tube.These factors,which include air preheating temperature,excess air coefficient,and fuel gas composition,were modified to study their effects on NO_(x) emissions under varying working conditions.Simulation results were compared with the theoretical calculation value based on chemical reaction equilibrium theory and the onsite experimental value to verify the simulation accuracy.The results show that NO_(x) emissions rise with increasing air preheating temperatures.NO_(x) production increases to an extreme value and then decreases during the oxygen-poor to oxygen-enriched process with the rise of the excess air coefficient.Enhancing the proportion of coke oven gas in the fuel gas raises the combustion temperature as well as the NO_(x) discharge.Both the thermal efficiency and NO_(x) emissions should be balanced.Therefore,the recommended values based on the simulation results are as follows:the air preheating temperature should not exceed 400℃,the excess air coefficient should be between 1.1 and 1.2,and the volume fraction of the coke oven gas should not exceed 30%.展开更多
文摘This paper presents an experimental study on the behavior of circular concrete columns reinforced by BFRP-PVC tubes under uniaxial loading.A total of six specimens were prepared and tested under uniaxial loading.The main parameters varied in the tests were strengthening ratio and strengthening approach of BFRP.The performance,such as failure modes,ultimate bearing capacity and stress-strain curves,was investigated in details and a formula was proposed to predict the compressive ultimate strength.The results show that this kind of confined columns obviously improves the ultimate bearing capacity,and the ultimate bearing capacity increases with the strengthening layers.The formula proposed is applicable and efficient for prediction of the ultimate bearing capacity as well.
基金the grants from the National Natural Science Foundation of China(Nos.52078152 and 12002095)Guangzhou Government-University Union Fund(No.202201020532)。
文摘In this article,the experimental and finite element analysis is utilized to investigate the quasi-static compression features of sandwich constructions built with tapered tubes.3D printing technology was utilized to create the hollow centers of the tapering tubes,with and without corrugations.The results demonstrate that the energy absorption(EA)and specific energy absorption(SEA)of the single corrugated tapered tube sandwich are 51.6% and 19.8% higher,respectively,than those of the conical tube sandwich.Furthermore,the results demonstrate that energy absorbers can benefit from corrugation in order to increase their efficiency.Additionally,the tapered corrugated tubes'resistance to oblique impacts was studied.Compared to a straight tube,the tapered tube is more resistant to oblique loads and has a lower initial peak crushing force(PCF),according to numerical simulations.After conducting a parametric study,it was discovered that the energy absorption performance of the sandwich construction is significantly affected by the amplitude,number of corrugations,and wall thickness.EA and SEA of DTS with corrugation number of 8 increased by 17.4%and 29.6%,respectively,while PCF decreased by 9.2% compared to DTS with corrugation number of 10.
基金supported by National Natural Science Foundation of China(Grant Nos.51975202(Junjia Cui received the grant)and 52175315(Guangyao Li received the grant)).
文摘Aluminum alloy thin-walled structures are widely used in the automotive industry due to their advantages related to light weight and crashworthiness.They can be produced at room temperature by the electrohydraulic forming process.In the present study,the influence of the related parameters on the forming quality of a 6063 aluminum alloy sinusoidal corrugation tube has been assessed.In particular,the orthogonal experimental design(OED)and central composite design(CCD)methods have been used.Through the range analysis and variance analysis of the experimental data,the influence degree of wire diameter(WD)and discharge energy(DE)on the forming quality was determined.Multiple regression analysis was performed using the response surface methodology.A prediction model for the attaching-die state coefficient was established accordingly.The following optimal arrangement of parameters was obtained(WD=0.759 mm,DE=2.926 kJ).The attaching-die state coefficient reached the peak value of 0.001.Better optimized wire diameter and discharge energy for a better attaching-die state could be screened by CCD compared with OED.The response surface method in CCD was more suitable for the design and optimization of the considered process parameters.
文摘Recently, tragic tailings dam collapses in Brazil have caused deaths and major destruction and the need to develop technologies capable of preventing damage to people and the environment. Brazilian tailings dams are in a situation of uncertainty due to new legislation that even requires decommissioning, an activity that involves many problems and where the risk of failure is the main one. An impact containment structure downstream of these dams can be effective and geotextile tubes, in a new approach, have emerged as an option with advantages in terms of execution, costs and safety. The technology is versatile and can bring many benefits such as the reuse of tailings or filling with low-energy or reused materials. In this research, geotextile tubes were tested as free containment barriers, experiencing impacts in reduced models. The safety factor for the stability of the structure was constructed using an equation which is the ratio between the self-weight of the barrier structure and its coefficient of static friction and the impact pressure, where the data showed an adequate correlation which suggests the viability of mitigating risks.
文摘Introduction: Fallopian diseases are often implicated in female infertility. Several radiological and surgical explorations have been proposed in order to evaluate the severity of lesions found in utero-adnexal pathology. Among tools that are used to investigate such pathologies, we have ultrasound, hysterosalpingography and endoscopy. But, in many developing countries like Cameroon, the usage of endoscopy in gynecology is not yet known by many practicians. The objective of our study was to show the interest of endoscopy in the diagnosis of fallopian tube pathologies. Methodology: We conducted a cross-sectional and descriptive study from March 1<sup>st</sup>, 2017 to May 31<sup>st</sup>, 2017 at the Gyneco-Obstetrics and Pediatric department of our Hospital. We included all women who presented infertility and underwent ultrasound, hysterosalpingography (HSG) and endoscopy at the Yaoundé Gyneco-obstetrics Hospital. We analyzed epidemiological parameters, clinics, ultrasound, hysterosalpingography and endoscopic finding. We used Cohen’s Kappa test to determine the correlation between HSG/endoscopy and ultrasound/endoscopy in the diagnosis of fallopian tube pathologies. The threshold was significant for a K-value > 0.20. Results: We got a sample of 156 women;the mean age was 32.6 ± 4.5 years. The Secondary infertility dominated in 66.7% of cases;31.1% of women presented a past medical history of sexually transmitted infections and 41.7% did abortions before. Endoscopic lesions were dominated by a fallopian obstruction in 54.5% of cases, 8.3% of adhesions, 33.9% of women presented uterine myomas, 37.8% of ovarian cysts and 1.3% of pelvic endometriosis. The K-values between HSG and endoscopy for distal and proximal tube obstructions were significant with respective thresholds of 0.25 and 0.30. The K-value between ultrasound and endoscopy was not significant with a threshold of 0.015 for the tubal hydrosalpinx. Conclusion: Endoscopy assessment appears as the most efficient tool to investigate fallopian tube diseases.
基金supported by the earmarked fund for China Agriculture Research System(CARS-28-37)the Agricultural Science and Technology Innovation Project of Shandong Academy of Agricultural Sciences,China(CXGC2022E21)+1 种基金the Youth Foundation of Shandong Institute of Pomology,China(GSS2022QN11)the Natural Science Foundation of Shandong Province,China(ZR2019BC075,ZR2020MC141,and ZR2021MC177)。
文摘Arabinogalactan proteins(AGPs)are widely distributed in the plant kingdom and play a vital role during the process of plant sexual reproduction.In this study,we performed a comprehensive identification of the PbrAGPs expressed in pear pollen and further explored their influences on pollen tube growth.Among the 187 PbrAGPs that were found to be expressed in pear pollen tubes,38 PbrAGPs were specifically expressed in pollen according to the RNA-seq data.The PbrAGPs were divided into two groups of highly expressed and specifically expressed in pear pollen.We further tested their expression patterns using RT-PCR and RT-qPCR.Most of the PbrAGPs were expressed in multiple tissues and their expression levels were consistent with reads per kilobase per million map reads(RPKM)values during pollen tube growth,implying that PbrAGPs might be involved in the regulation of pear pollen tube growth.We also constructed phylogenetic trees to identify the functional genes in pear pollen tube growth.Therefore,19 PbrAGPs(PbrAGP1 to PbrAGP19)were selected to test their influences on pollen tube growth.Recombinant proteins of the 19 PbrAGP-His were purified and used to treat pear pollen,and 11 of the PbrAGP-His recombinant proteins could promote pear pollen tube growth.Additionally,pollen tube growth was inhibited when the expression levels of PbrAGP1 and PbrAGP5 were knocked down using an antisense oligonucleotide assay.PbrAGP1 and PbrAGP5 were localized in the plasma membrane and might not alter the distribution of pectin in the pollen tube.In summary,this study identified the PbrAGPs expressed in pear pollen and lays the foundation for further exploring their functions in pollen tube growth.
基金supported by the Department of Science and Technology(DST,India)through the Indo-Russian collaborative project scheme。
文摘Protecting occupants or payloads in crashes and blasts is of utmost importance in both moving and immobile structures.One way of achieving this is by using a sacrificial energy absorber.Composite tubes have been studied as potential energy absorbers due to their ability to fail progressively under axial compression.In this study,the energy absorption capability of these tubes is enhanced by adding hollow glass particles to the matrix.Drop-weight tests are performed on composite tubes,and a digital image correlation(DIC)-based technique is used to capture their load-displacement behaviour.This eliminates the use of electronic data acquisition systems,load cells,and accelerometers.The load-displacement curves of the tubes are obtained from the DIC-based technique and examined to understand their crushing behaviour.Although the mean crush load shows a drop,an increase in crush length is noticed.The specific energy absorbed by the tubes improves with an increase in GMB volume fraction.The addition of 0.1,0.2,0.3 and 0.4 vol fractions of GMB results in the specific energy absorption increasing by6.6%,14.7%,24%and 36.6%,respectively,compared to neat glass fibre-epoxy tubes.Visual examination of the tubes and comparison with tubes subject to quasi-static compression is also performed.
基金supported by the National Natural Science Foundation of China(No.41877251)Major Science and Technology Projects of Xinxiang City(No.21ZD012).
文摘The thermal transmission coefficient for a micro-ribbed tube has been determined using theoretical relationships and the outcomes of such calculations have been compared with experiments conducted using a R1234yf refrigerant undergoing condensation.In particular four theoretical single-phase flow and three multi-phase flow models have been used in this regard.The experimental results show that:the Oliver et al.criterion equation overestimates the experimental results as its accuracy is significantly affected by the specific conditions realized inside micro-fin tubes;the Miyara et al.criterion equation prediction error is less than 15%;the Cavallini et al.approach gives the highest prediction accuracy;the Goto et al.model overestimates the test data.Such results are critically discussed and some indications for the improvement of such models are provided.
文摘AIM:To evaluate the pathogens in cultured Jones tubes used in lacrimal bypass surgery according to the postoperative periods and to obtain data for the prevention of infection of functional lacrimal stent invention.METHODS:Totally 71 patients(81 eyes)who underwent the removal of Jones tubes were enrolled in study.All the removed Jones tubes were cultured for bacterial and fungal identification and tested for bacterial antibiotic sensitivity.The results were analyzed according to the duration of the inserted Jones tube after lacrimal bypass surgery.RESULTS:Of the 81 eyes,bacteria were isolated from 69 eyes(85.2%)and fungi from 6 eyes(7.4%).Among 69 eyes,40.6% showed Staphylococcus aureus(S.aureus),11.6% were Pseudomonas aeruginosa(P.aeruginosa).Gram-positive bacteria were isolated more than Gramnegative bacteria,but Gram-negative bacteria showed a higher incidence in the Jones tube implanted for over 10y(P=0.035).The antibiotic sensitivity test showed that 46.4% of S.aureus were resistant to oxacillin.In terms of antibiotics commonly used in ocular clinical practice,vancomycin was sensitive to S.aureus and Streptococcus pneumoniae(S.pneumoniae),amikacin responded to P.aeruginosa and Proteus mirabilis(P.mirabilis).Trimethoprim/sulfamethoxazole(TMP/SMX)was all sensitive to S.aureus,S.pneumoniae and P.mirabilis except P.aeruginosa.CONCLUSION:S.aureus is the most commonly found organism in the Jones tube after lacrimal bypass surgery,and 46.4% of them are methicillin-resistant S.aureus(MRSA),sensitive to vancomycin.Especially,P.mirabilis responded with amikacin is dominantly detected in the Jones tubes implanted for more than 10y.
文摘Introduction: Endotracheal suction plays a crucial role in the management of mechanically ventilated patients. This study aims to evaluate the clinical effectiveness and safety of suction tubes with markings in mechanically ventilated pediatric patients. Materials and Methods: A randomized assignment was carried out on a cohort of 52 pediatric patients who underwent mechanical ventilation in the Pediatric Intensive Care Unit at the Third Affiliated Hospital of Sun Yat-sen University, covering the period from January 2022 to December 2022. These patients were divided into two groups: an improved group (n = 26) utilizing marked suction tubes, and a regular group (n = 26) employing conventional suction tubes. The objective of our study was to evaluate the clinical effectiveness of marked suction tubes. Results: The effects of the improved group on the vital signs of children undergoing mechanical ventilation were small and statistically significant compared with the regular group (p < 0.05). Additionally, the improved group exhibited a reduced frequency of sputum suction, shorter mechanical ventilation duration, and fewer days of hospitalization in the PICU compared to the regular group during the ventilation period. Notably, the difference in the duration of PICU hospitalization was statistically significant (p < 0.05). Moreover, the incidence of adverse reactions in the improved group was notably lower, with statistically significant differences observed in airway mucous membrane damage and irritating cough when compared to the regular group (p < 0.05). Conclusion: The utilization of marked suction tubes provides clinical nurses with clear guidance for performing suctioning with ease, efficiency and safety. Consequently, advocating for the widespread implementation of marked suction tubes in clinical practice is a commendable pursuit.
文摘Bubble and slurry bubble column reactors(BCRs/SBCRs)are used for various chemical,biochemical,and petro-chemical applications.They have several operational and maintenance advantages,including excellent heat and mass transfer rates,simplicity,and low operating and maintenance cost.Typically,a catalyst is present in addition to biochemical processes where microorganisms are used to produce industrially valuable bio-products.Since most applications involve complicated gas-liquid,gas-liquid-solid,and exothermic processes,the BCR/SBCR must be equipped with heat-exchanging tubes to dissipate heat and control the reactor’s overall performance.In this review,past and very recent experimental and numerical investigations on such systems are critically dis-cussed.Furthermore,gaps to befilled and critical aspects still requiring investigation are identified.
基金supported by the Natural Science Foundation of China(91963202 and 52072372)the Key Research Program of Frontier Sciences(CAS,Grant,QYZDJ-SSW-SLH046)the CAS/SAFEA International Partnership Program for Creative Research Teams,and the Hefei Institutes of Physical Science,Chinese Academy of Sciences Director’s Fund(YZJ ZX202018)
文摘Transition metal oxides are regarded as promising candidates of anode for next-generation lithium-ion batteries(LIBs)due to their ultrahigh theoretical capacity and low cost,but are restricted by their low conductivity and large volume expansion during Li^(+)intercalation.Herein,we designed and constructed a structurally integrated 3D carbon tube(3D-CT)grid film with Mn_(3)O_(4)nanoparticles(Mn_(3)O_(4)-NPs)and carbon nanotubes(CNTs)filled in the inner cavity of CTs(denoted as Mn_(3)O_(4)-NPs/CNTs@3D-CT)as high-performance free-standing anode for LIBs.The Mn_(3)O_(4)-NPs/CNTs@3D-CT grid with Mn_(3)O_(4)-NPs filled in the inner cavity of 3D-CT not only afford sufficient space to overcome the damage caused by the volume expansion of Mn_(3)O_(4)-NPs during charge and discharge processes,but also achieves highly efficient channels for the fast transport of both electrons and Li+during cycling,thus offering outstanding electrochemical performance(865 mAh g^(-1)at 1 A g^(-1)after 300 cycles)and excellent rate capability(418 mAh g^(-1)at 4 A g^(-1))based on the total mass of electrode.The unique 3D-CT framework structure would open up a new route to the highly stable,high-capacity,and excellent cycle and high-rate performance free-standing electrodes for highperformance Li-ion storage.
文摘The microstructure of the thin-walled tubes with high-strength aluminum alloy determines their final forming quality and performance. This type of tube can be manufactured by multi-pass hot power backward spinning process as it can eliminate casting defects, refine microstructure and improve the plasticity of the tube. To analyze the microstructure distribution characteristics of the tube during the spinning process, a 3D coupled thermo-mechanical FE model coupled with the microstructure evolution model of the process was established under the ABAQUS environment. The microstructure evolution characteristics and laws of the tube for the whole spinning process were analyzed. The results show that the dynamic recrystallization is mainly produced in the spinning deformation zone and root area of the tube. In the first pass, the dynamic recrystallization phenomenon is not obvious in the tube. With the pass increasing, the trend of dynamic recrystallization volume percentage gradually increases and extends from the outer surface of the tube to the inner surface. The fine-grained area shows the states of concentration, dispersion, and re-concentration as the pass number increases. .
文摘BACKGROUND Since its description in 1790 by Hunter,the nasogastric tube(NGT)is commonly used in any healthcare setting for alleviating gastrointestinal symptoms or enteral feeding.However,the risks associated with its placement are often underes-timated.Upper airway obstruction with a NGT is an uncommon but potentially life-threatening complication.NGT syndrome is characterized by the presence of an NGT,throat pain and vocal cord(VC)paralysis,usually bilateral.It is poten-tially life–threatening,and early diagnosis is the key to the prevention of fatal upper airway obstruction.However,fewer cases may have been reported than might have occurred,primarily due to the clinicians'unawareness.The lack of specific signs and symptoms and the inability to prove temporal relation with NGT insertion has made diagnosing the syndrome quite challenging.AIM To review and collate the data from the published case reports and case series to understand the possible risk factors,early warning signs and symptoms for timely detection to prevent the manifestation of the complete syndrome with life-threatening airway obstruction.METHODS We conducted a systematic search for this meta-summary from the database of PubMed,EMBASE,Reference Citation Analysis(https://www.referencecitation-analysis.com/)and Google scholar,from all the past studies till August 2023.The search terms included major MESH terms"Nasogastric tube","Intubation,Gastrointestinal","Vocal Cord Paralysis",and“Syndrome”.All the case reports and case series were evaluated,and the data were extracted for patient demographics,clinical symptomatology,diagnostic and therapeutic interventions,clinical course and outcomes.A datasheet for evaluation was further prepared.RESULTS Twenty-seven cases,from five case series and 13 case reports,of NGT syndrome were retrieved from our search.There was male predominance(17,62.96%),and age at presentation ranged from 28 to 86 years.Ten patients had diabetes mellitus(37.04%),and nine were hypertensive(33.33%).Only three(11.11%)patients were reported to be immunocompromised.The median time for developing symptoms after NGT insertion was 14.5 d(interquartile range 6.25-33.75 d).The most commonly reported reason for NGT insertion was acute stroke(10,37.01%)and the most commonly reported symptoms were stridor or wheezing 17(62.96%).In 77.78%of cases,bilateral VC were affected.The only treatment instituted in most patients(77.78%)was removing the NG tube.Most patients(62.96%)required tracheostomy for airway protection.But 8 of the 23 survivors recovered within five weeks and could be decannulated.Three patients were reported to have died.CONCLUSION NGT syndrome is an uncommon clinical complication of a very common clinical procedure.However,an under-reporting is possible because of misdiagnosis or lack of awareness among clinicians.Patients in early stages and with mild symptoms may be missed.Further,high variability in the presentation timing after NGT insertion makes diagnosis challenging.Early diagnosis and prompt removal of NGT may suffice in most patients,but a significant proportion of patients presenting with respiratory compromise may require tracheostomy for airway protection.
文摘Thin-walled structures are widely used in cars due to their lightweight construction and energy-absorbing properties.However,issues such as high initial stress and lowenergy-absorbing efficiency arise.This study proposes a novel energy-absorbing structure inwhich a straight tube is combinedwith a conical tube and a bamboo-inspired bulkhead structure is introduced.This configuration allows the conical tube to flip outward first and then fold together with the straight tube.This deformation mode absorbs more energy and less peak force than the conical tube sinking and flipping inward.Through finite element numerical simulation,the specific energy absorption capacity of the structure is increased by 26%compared to that of a regular circular cross-section tube.Finally,the impact resistance of the bionic straight tapered tube structure is further improved through multi-objective optimization,promoting the engineering application and lightweight design of hybrid cross-section tubes.
基金supported by the National Natural Science Foundation of China(Nos.51974082,51901037)State Key Laboratory of Baiyunobo Rare Earth Resource Research and Comprehensive Utilization(No.2021H2279)Programme of Introducing Talents of Discipline Innovation to Universities 2.0(the 111 Project 2.0 of China,No.BP0719037).
文摘In this study,the extruded Mg-Zn-Mn-Ce-Ca alloy tube with a low compression anisotropy along the ED,45ED and TD was prepared.The effect of the second phases,initial texture and deformation behavior on this low mechanical anisotropy was investigated.The results revealed that the alloy tube contains the high content(Mg1-xZnx)11Ce phase and the low content of Mg12Ce phase.These second phases are respectively incoherent and coherent with the Mg matrix,and their influence can be ignored.Additionally,the alloy tube exhibited a weak basal fiber texture,where the c-axis was aligned along the 0°∼30°tilt from TD to ED.Such a texture made the initial deformation(at 1.0%∼1.6%strain)of the three samples controlled by comparable basalslip.As deformation progressed(1.6∼9.0%strain),larger amounts of ETWs nucleated and gradually approached saturation in the three samples,re-orienting the c-axis to a 0°∼±30°deviation with respect to the loading directions.Meanwhile,the prismatic and pyramidal<c+a>slips replaced the dominant deformation progressively until fracture.Eventually,the similar deformation mechanisms determined by the weak initial texture in the three samples contribute to the comparable strain hardening rates,resulting in the low compressive anisotropy of the alloy tube.
基金Project supported by the National Natural Science Foundation of China (Nos. 12272290 and11872291)the State Key Laboratory of Automotive Safety and Energy of China (No. KFY2202)。
文摘In this paper, a novel efficient energy absorber with free inversion of a metal foam-filled circular tube(MFFCT) is designed, and the axial compressive behavior of the MFFCT under free inversion is studied analytically and numerically. The theoretical analysis reveals that the energy is mainly dissipated through the radial bending of the metal circular tube, the circumferential expansion of the metal circular tube, and the metal filled-foam compression. The principle of energy conservation is used to derive the theoretical formula for the minimum compressive force of the MFFCT over free inversion under axial loading. Furthermore, the free inversion deformation characteristics of the MFFCT are analyzed numerically. The theoretical steady values are found to be in good agreement with the results of the finite element(FE) analysis. The effects of the average diameter of the metal tube, the wall thickness of the metal tube, and the filled-foam strength on the free inversion deformation of the MFFCT are considered. It is observed that in the steady deformation stage, the load-carrying and energy-absorbing capacities of the MFFCT increase with the increase in the average diameter of the metal tube, the wall thickness of the metal tube, or the filled-foam strength. The specific energy absorption(SEA) of free inversion of the MFFCT is significantly higher than that of the metal tube alone.
文摘Background: Sudden sensorineural hearing loss(SSNHL) is a prevalent emergency in ear, nose, and throat practice. Previous studies have demonstrated that intratympanic steroid therapy(IST) can serve as a salvage treatment for SSNHL after the failure of systemic steroid therapy(SST).Objective: This study aimed to analyze the efficacy of modified IST involving the insertion of a tympanic tube and gelfoam as a salvage treatment for patients with SSNHL, and to explore its associated factors.Methods: Totally, 74 patients who were aged 22–81 years with SSNHL were enrolled and allocated to either the control group(n = 25) or the treatment group(n = 49) based on their treatment modalities. All patients received SST lasting for at least 7 days. Subsequently, patients in the treatment group, after SST failure, underwent IST twice a week for 2–6 weeks, while the control group did not. Efficacy was assessed by the improvement in pure tone average at the affected frequency at the beginning and end of IST.Results: Hearing improvement in all patients after IST in the treatment group was 9.71 ± 14.84 dB, with significant improvement at affected frequencies(250-8000 Hz) compared with the control group(P < 0.05). The findings indicated the duration from the onset of SSNHL to the beginning of IST as an independent factor for pure tone average improvement after treatment(P = 0.002), whereas age, duration of SST, and time of IST were not(P > 0.05).Conclusion: The modified IST was demonstrated to be a safe and effective method as a salvage treatment for SSNHL. This study explored the efficacy of a modified IST approach, incorporating the utilization of tympanic tubes and gelfoam as key components. The findings underscore the advantages of gelfoam as a strategic drug carrier placed in the round window niche. By minimizing drug loss, extending action time, and increasing perilymph concentration, gelfoam enhances the therapeutic impact of IST, contributing to improved hearing outcomes in patients with SSNHL.
文摘The radiant tube burner was modeled and analyzed by the numerical simulation method to investigate the influence factors and rules of NO_(x) emissions in a W-type radiant tube.These factors,which include air preheating temperature,excess air coefficient,and fuel gas composition,were modified to study their effects on NO_(x) emissions under varying working conditions.Simulation results were compared with the theoretical calculation value based on chemical reaction equilibrium theory and the onsite experimental value to verify the simulation accuracy.The results show that NO_(x) emissions rise with increasing air preheating temperatures.NO_(x) production increases to an extreme value and then decreases during the oxygen-poor to oxygen-enriched process with the rise of the excess air coefficient.Enhancing the proportion of coke oven gas in the fuel gas raises the combustion temperature as well as the NO_(x) discharge.Both the thermal efficiency and NO_(x) emissions should be balanced.Therefore,the recommended values based on the simulation results are as follows:the air preheating temperature should not exceed 400℃,the excess air coefficient should be between 1.1 and 1.2,and the volume fraction of the coke oven gas should not exceed 30%.