Disturbance failure mechanism of highly stressed rock in deep excavation:Current status and prospects

This article reviews the current status on the dynamic behavior of highly stressed rocks under disturbances.Firstly,the experimental apparatus,methods,and theories related to the disturbance dynamics of deep,high-stress rock are reviewed,followed by the introduction of scholars’research on deep rock deformation and failure from an energy perspective.Subsequently,with a backdrop of highstress phenomena in deep hard rock,such as rock bursts and core disking,we delve into the current state of research on rock microstructure analysis and residual stresses from the perspective of studying the energy storage mechanisms in rocks.Thereafter,the current state of research on the mechanical response and the energy dissipation of highly stressed rock formations is briefly retrospected.Finally,the insufficient aspects in the current research on the disturbance and failure mechanisms in deep,highly stressed rock formations are summarized,and prospects for future research are provided.This work provides new avenues for the research on the mechanical response and damage-fracture mechanisms of rocks under high-stress conditions.

Stress granules inhibit endoplasmic reticulum stress-mediated apoptosis during hypoxia-induced injury in acute liver failure

BACKGROUND Stress granules(SGs)could be formed under different stimulation to inhibit cell injury.AIM To investigate whether SGs could protect hepatocytes from hypoxia-induced damage during acute liver failure(ALF)by reducing endoplasmic reticulum stress(ERS)mediated apoptosis.METHODS The agonist of SGs,arsenite(Ars)was used to intervene hypoxia-induced hepatocyte injury cellular model and ALF mice models.Further,the siRNA of activating transcription factor 4(ATF4)and SGs inhibitor anisomycin was then used to intervene in cell models.RESULTS With the increase of hypoxia time from 4 h to 12 h,the levels of HIF-1α,ERS and apoptosis gradually increased,and the expression of SGs marker G3BP1 and TIA-1 was increased and then decreased.Compared with the hypoxia cell model group and ALF mice model,the levels of HIF-1α,apoptosis and ERS were increased in the Ars intervention group.After siRNA-ATF4 intervention,the level of SGs in cells increased,and the levels of HIF-1α,ERS and apoptosis decreased.Compared with the siRNA-ATF4 group,the levels of G3BP1 in the siRNAATF4+anisomycin group were decreased,and the levels of HIF-1α,ERS and apoptosis were increased.Moreover,compared with the ALF group,the degree of liver injury and liver function,the levels of HIF-1α,ERS and apoptosis in the Ars intervention group were decreased,the level of SGs was increased.CONCLUSION SGs could protect hepatocytes from hypoxia-induced damage during ALF by reducing ERSmediated apoptosis.

Metabolomic-based analysis reveals bile acid-mediated ovarian failure induced by low temperature in zebrafish

As ectotherms, fish are highly sensitive to temperature fluctuations, which can profoundly impact their reproductive cycles. In this study, we investigated the fertility and histological characteristics of zebrafish(Danio rerio) ovaries exposed to a temperature gradient ranging from the thermopreferendum temperature of the species,27℃, to lower temperatures of 22℃, 20℃, and 13℃ over a period of two weeks. Comparative metabolomic(six biological replicates for each temperature) and transcriptomic(four biological replicates for each temperature) analyses were conducted under the four temperature conditions. Results indicated that lower temperatures inhibited oocyte development and differential metabolites were involved in steroid hormone production,antioxidant function, and lipid and protein catabolism.Disrupted reproductive hormones, increased proteolysis,and lipid degradation significantly impeded oocyte development and egg maturation. Notably, a significant increase in bile acid content was noted in the ovaries of the cold-treated fish, indicating that bile acids play a critical role in ovarian failure. Overall, these findings provide valuable insights into the mechanisms governing the reproductive response of fish to cold stress.

A generalized nonlinear three-dimensional Hoek‒Brown failure criterion

To understand the strengths of rocks under complex stress states,a generalized nonlinear threedimensional(3D)Hoek‒Brown failure(NGHB)criterion was proposed in this study.This criterion shares the same parameters with the generalized HB(GHB)criterion and inherits the parameter advantages of GHB.Two new parameters,b,and n,were introduced into the NGHB criterion that primarily controls the deviatoric plane shape of the NGHB criterion under triaxial tension and compression,respectively.The NGHB criterion can consider the influence of intermediate principal stress(IPS),where the deviatoric plane shape satisfies the smoothness requirements,while the HB criterion not.This criterion can degenerate into the two modified 3D HB criteria,the Priest criterion under triaxial compression condition and the HB criterion under triaxial compression and tension condition.This criterion was verified using true triaxial test data for different parameters,six types of rocks,and two kinds of in situ rock masses.For comparison,three existing 3D HB criteria were selected for performance comparison research.The result showed that the NGHB criterion gave better prediction performance than other criteria.The prediction errors of the strength of six types of rocks and two kinds of in situ rock masses were in the range of 2.0724%-3.5091%and 1.0144%-3.2321%,respectively.The proposed criterion lays a preliminary theoretical foundation for prediction of engineering rock mass strength under complex in situ stress conditions.

Evolution of Coulomb failure stress in Sulaiman Lobe,Pakistan,and its implications for seismic hazard assessment

In this research work,we present the evolution of Coulomb failure stress(CFS)in the Sulaiman Lobe and its implications for seismic hazard assessment.The Chaman transform fault,~1,000 km long,is the major active fault that marks the western boundary between Pakistan and Afghanistan on the Indian Plate.To date,few studies have been conducted to unveil the interactions among earthquakes and the implications of these interactions for seismic hazard assessment in the region.We thoroughly investigated the published and online catalog to construct a sequence of major earthquakes that occurred in this region during the past.The final earthquake sequence was composed of 15 earthquakes of M_(w)≥6.0,beginning with the 1888 earthquake.We used the stress-triggering theory to numerically simulate the evolution of CFS caused by these earthquakes.The numerical results revealed that 8 out of 15earthquakes were triggered by the preceding earthquakes.The earthquakes in 1908,1910,1935,1966,and 1997 were rather independent earthquakes in this sequence.Although the epicenters of the 1975a and 1975b earthquakes were in the stress shadow zone,the partial rupture segments of both these earthquakes were in high-CFS regions.The CFS induced by the 1935 earthquake was notable,as it later triggered the 2008 doublet.Moreover,our results revealed that the northern segment of the Chaman Fault,the southern segment of the Ghazaband Fault,and the northwestern segment of the Urghargai Fault demonstrated a high change in CFS that could trigger seismicity in these regions.The necessary arrangements must therefore be made to mitigate any possible seismic hazards in the region.

Failure behavior around a circular opening in a rock mass with non-persistent joints:A parallel-bond stress corrosion approach

The stability of underground excavations is influenced by discontinuities interspaced in surrounding rock masses as well as the stress condition. In this work, a numerical study was undertaken on the failure behavior around a circular opening in a rock mass having non-persistent open joints using PFC software package. A parallel-bond stress corrosion(PSC) approach was incorporated to drive the failure of rock mass around the circular opening, such that the whole progressive failure process after excavation was reproduced. Based on the determined micro parameters for intact material and joint segments, the failure process around the circular opening agrees very well with that obtained through laboratory experiment. A subsequent parametric study was then carried out to look into the influence of lateral pressure coefficient, joint dip angle and joint persistency on the failure pattern and crack evolution of the rock mass around the circular opening. Three failure patterns identified are step path failure, planar failure and rotation failure depending on the lateral pressure coefficient. Moreover, the increment of joint dip angle and joint persistency aggravates the rock mass failure around the opening. This study offers guideline on stability estimation of underground excavations.

On the excavation-induced stress drop in damaged coal considering a coupled yield and failure criterion

Investigating the stress drop of abutment pressure is the key to a deep quantitative analysis of the discontinuous stress redistribution under mining.In the present study,uniaxial and triaxial compression tests are carried out separately to determine the bulk and shear moduli,the cohesion,and the internal friction angle of the coal samples.By extending the meaning of Mohr’s circle referring to yield stress instead of the maximum principal stress,a yield line is introduced to illustrate the stress drop of Mohr’s circle referring to yield stress instead of the maximum principal stress at the elastoplastic boundary.Furthermore,a theoretical solution of the stress drop as a function of the damage is proposed to investigate how the abutment pressure differs considering the yield line and failure line.In addition,applying the stress drop at the yield line in non-pillar mining,top coal mining,and protective coal mining shows that the damage has a nonlinearly positive influence on the stress drop.The results shows that the bulk modulus and internal friction angle have a more sensitive influence on the stress drop than do the shear modulus and cohesion.Finally,the stress drop is divided into a discontinuous stress drop at the yield line and a structural stress drop at the failure line.The stress drop is effective in describing the discontinuous stress redistribution and shows a clear difference in the movement direction of Mohr’s circle considering the unloading pressure.

Failure criterion for soft rocks considering intermediate principal stress

The significant differences between hard rocks(more brittle)and soft rocks(more ductile)may suggest the use of different failure criteria.A strength criterion for soft rocks that includes intermediate principal stress was proposed.The new criterion includes two independent parameters:the uniaxial compressive strength(σ_(ci)),which can be obtained from common laboratory tests or indirectly estimated by alternative index tests in the laboratory or field;and f(joint),which is used to characterize the rock mass quality and can be easily estimated.The authors compared the predictive capabilities of the new criterion with other criteria using the database of soft rocks under two conditions:with and without triaxial data.For the estimation of triaxial and true-triaxial strengths,the new criterion generally produced a better fit.The proposed criterion is practical for an approximate first estimation of rock mass strength,even without triaxial data,as it balances accuracy(lower prediction error)and simplicity(fewer independent parameters).

Shortness of breath in clinical practice: A case for left atrial function and exercise stress testing for a comprehensive diastolic heart failure workup

The symptom cluster of shortness of breath(SOB) contributes significantly to the outpatient workload of cardiology services. The workup of these patients includes blood chemistry and biomarkers, imaging and functional testing of the heart and lungs. A diagnosis of diastolic heart failure is inferred through the exclusion of systolic abnormalities, a normal pulmonary function test and normal hemoglobin, coupled with diastolic abnormalities on echocardiography. Differentiating confounders such as obesity or deconditioning in a patient with diastolic abnormalities is difficult. While the most recent guidelines provide more avenues for diagnosis, such as incorporating the left atrial size, little emphasis is given to understanding left atrial function, which contributes to at least 25% of diastolic left ventricular filling; additionally, exercise stress testing to elicit symptoms and test the dynamics of diastolic parameters, especially when access to the "gold standard" invasive tests is lacking, presents clinical translational gaps. It is thus important in diastolic heart failure work up to understand left atrial mechanics and the role of exercise testing to build a comprehensive argument for the diagnosis of diastolic heart failure in a patient presenting with SOB.

Comparison of large deformation failure control method in a deep gob-side roadway: A theoretical analysis and field investigation

Under the dual influence of the mining disturbance of the previous working face and the advanced mining of the working face,the roadway is prone to large deformation,failure,and rockburst.Roadway stabilization has always significantly influenced deep mining safety.In this article we used the research background of the large deformation failure roadway of Fa-er Coal Mine in Guizhou Province of China to propose two control methods:bolt-cable-mesh+concrete blocks+directional energy-gathering blasting(BCM-CBDE method)and 1st Generation-Negative Poisson’s Ratio(1G NPR)cable+directional energy-gathering blasting+dynamic pressure stage support(πgirder+single hydraulic prop+retractable U steel)(NPR-DEDP method).Meantime,we compared the validity of the large deformation failure control method in a deep gob-side roadway based on theoretical analysis,numerical simulations,and field experiments.The results show that directional energy-gathering blasting can weaken the pressure acting on the concrete blocks.However,the vertical stress of the surrounding rock of the roadway is still concentrated in the entity coal side and the concrete blocks,showing a’bimodal’distribution.BCM-CBDE method cannot effectively control the stability of the roadway.NPR-DEDP method removed the concrete blocks.It shows using the 1G NPR cable with periodic slipping-sticking characteristics can adapt to repeated mining disturbances.The peak value of the vertical stress of the roadway is reduced and transferred to the deep part of the surrounding rock mass,which promotes the collapse of the gangue in the goaf and fills the goaf.The pressure of the roadway roof is reduced,and the gob-side roadway is fundamentally protected.Meantime,the dynamic pressure stage support method withπgirder+single hydraulic prop+retractable U steel as the core effectively protects the roadway from dynamic pressure impact when the main roof is periodically broken.After the on-site implementation of NPR-DEDP method,the deformation of the roadway is reduced by more than 45%,and the deformation rate is reduced by more than 50%.

A study of grid failure mode drivers and methods for accelerated life testing of a 30cm diameter ion thruster

In view of the high cost caused by the 1:1 lifetime verification test of ion thrusters,the lifetime acceleration test should be considered.This work uses the PIC-MCC(Particle-in-Cell MonteCarlo Collision)method to analyze the five failure factors that lead to the failure of the accelerator grid of a 30 cm diameter ion thruster under the working mode of 5 k W.Meanwhile,the acceleration stress levels corresponding to different failure factors are obtained.The results show that background pressure has the highest stress level on the grid's erosion.The accelerator grid aperture's mass sputtering rate under the rated vacuum degree(1×10^(-4)Pa)of 5 k W work mode is 8.78 times that of the baseline vacuum degree(1×10^(-6)Pa),and the mass sputtering rate under worse vacuum degree(5×10^(-3)Pa)is 5.08 times that of 1×10^(-4)Pa.Under the influence of the other four failure factors,namely,the voltage of the accelerator grid,upstream plasma density,the screen grid voltage and mass utilization efficiency,the mass sputtering rates of the accelerator grid hole are 2.32,2.67,1.98 and 2.51 times those of the accelerator grid hole under baseline condition,respectively.The ion sputtering results of two 30 cm diameter ion thrusters(both installed with new grids assembly)after working for 1000 h show that the mass sputtering rate of the accelerator grid hole under vacuum conditions of 5×10^(-3)Pa is 4.54 times that under the condition of 1×10^(-4)Pa,and the comparison error between simulation results and test results of acceleration stress is about 10%.In the subsequent ion thruster lifetime verification,the working vacuum degree can be adjusted according to the acceleration stress level of background pressure,so as to shorten the test time and reduce the test cost.

Parameters Calibration of the GISSMO Failure Model for SUS301L-MT

With the development of the rail transit industry,more attention has been paid to the passive safety of rail vehicles.Structural damage is one of the main failure behaviors in a rail vehicle collision,but it has been paid little attention to in past research.In this paper,the quasi-static fracture experiments of SUS301L-MT under different stress states were carried out.The mechanical fracture properties of this material were studied,and the corresponding finite element simulation accuracy was improved to guide the design of vehicle crashworthiness.Through the tests,the fracture behavior of materials with wide stress triaxiality was obtained,and each specimen’s fracture locations and fracture strains were determined.Parameters of a generalized incremental stress state dependent damage model(GISSMO)of the material were calibrated,and the model’s accuracy was verified with test results from a 45°shear specimen.The GISSMO failure model accurately reflected the fracture characteristics of the material.The mesh dependency of this model was modified and discussed.The results show that the simulation agrees well with experimental data for the force-displacement curve after correction,but the strain distribution needs to be further studied and improved.

Effect of stress paths on failure mechanism and progressive damage of hard-brittle rock

During deep buried hard-brittle rock tunnel excavation,the surrounding rock experiences a complicated stress path and stress adjustment process.Once the adjusted stress exceeds the ultimate bearing capacity of rockmass,a rock failure mode defined as stress-cracking type will occur.In order to investigate the effect of stress paths on failure mechanism and progressive damage of deep-buried rockmass,the cyclic loading-unloading,loading-unloading,uniaxial,conventional and unloading triaxial compression tests on samples of hard-brittle sandstone were conducted.According to the experimental results,increase in the confining pressure was beneficial to improve the mechanical parameters of rock,but it will reduce the brittle failure features.Compared with conventional triaxial compression,the sandstone under unloading state had more remarkable stress drop and unstable failure characteristics.Meanwhile,it was found that the energy dissipation and energy release in the whole process of rock deformation were the internal power of driven rock progressive damage.With the increase of confining pressure,the energy hardening and energy accumulation features of rock were weakened,while the progressive damage evolution characteristics could be enhanced.In unloading state,more energy could be converted into elastic energy in the energy softening phase(σeb-σP),so that the prepeak damage rate of rock was lower than that of conventional triaxial compression state.Thus,the energy dissipation rate of rock after peak strength decreased linearly with the increase of confining pressure under conventional triaxial compression state,while in unloading state it showed the opposite law.

Definition of failure criterion for frozen soil under directional shear-stress path

A series of directional shear tests on remolded frozen soil was carried out at 10°C by using a hollow cylinder apparatus to study failure criterion under a directional shear-stress path.Directional shear tests were conducted at five shear rates(10,20,30,40,and 50 kPa/min)and five intermediate principal stress coefficients(b=0,0.25,0.5,0.75,and 1),with the mean principal stress(p=4.5 MPa)kept constant.The results show that the torsional strength and the generalized strength both increase with the increase of the shear rates.According to the failure modes of frozen soil under different shear rates,the specimens present obvious plastic failure and shear band;and the torsional shear component dominates the failure modes of hollow cylindrical specimens.A shear rate of 30 kPa/min is chosen as the loading rate in the directional shear tests of frozen soil.The shape of the failure curve in theπplane is dependent on the directional anglesαof the major prin cipal stress.It is reasonable to use the strain-hardening curves to define the deviatoric stress value atγg=15%(generalized shear strain)as the failure criterion of frozen soil under a directional shear-stress path.

Identifying the most explainable fault ruptured of the 2018 Palu-Donggala earthquake in Indonesia using coulomb failure stress and geological field report

This study investigates the relation between the Coulomb failure stress of the mainshock with the aftershocks sequence following the 2018 Palu-Donggala earthquake in Indonesia.We calculate the Coulomb failure stress using the available coseismic fault models,which had varied moment magnitudes between M_W7.53~M_W7.62.Different interpretations of the fault sources were suggested by previous studies.While two fault models suggested that one inland fault segment ruptured during the earthquake,another fault model proposed that two fault segments ruptured inland of Central Sulawesi and along the coast of Palu bay.We further overlay the positive and negative values of Coulomb failure stress with the reported relocated aftershock.We find that only by conducting Coulomb failure stress analysis,we can not favour the preference of the coseismic fault which explains aftershock distribution.This investigation demonstrates that additional observational data from geological field surveys are required to identify the surface rupture in comparison with the coseismic fault model.

Acoustic emission characteristics and stress release rate of coal samples in different dynamic destruction time

Considering the importance of the prediction of rock burst disasters, and in order to grasp the law of acoustic emission(AE) of coal samples in different dynamic destruction time, the SH-II AE monitoring system was adopted to monitor the failure process of coal samples. The study of the change rule of the AE numbers, energy, ‘b' value and spectrum in the micro crack propagation process of the coal samples shows that as dynamic damage time went by, AE presented high-energy counts and the accumulated counts increased during the compression phase. The AE energy and cumulative counts increased during the elastic stage. The AE blank area increased gradually and the blank lines were more and more obvious in the molding stage. The AE counts and energy showed a trend of decrease in the residual damage phase.AE ‘b' values gradually became sparse, and the large scale cracks percentage compared with micro cracks decreased and the degree of damage decreased. The AE frequency spectrum peak went from the residual damage phase to the molding phase, and finally it was nearly stable, besides the bandwidth of the main frequency is gradually narrowed. Also, the frequency peak changed from single peak frequency to bi-peak frequency and to the single peak frequency. Uniaxial compressive strength is more sensitive than the elastic modulus to dynamic damage time.

Virtual strain loading method for low temperature cohesive failure of asphalt binder

Cohesive failure is one of the primary reasons for low-temperature cracking in asphalt pavements.Understanding the micro-level mechanism is crucial for comprehending cohesive failure behavior.However,previous literature has not fully reported on this aspect.Moreover,there has been insufficient attention given to the correlation between macroscopic and microscopic failures.To address these issues,this study employed molecular dynamics simulation to investigate the low-temperature tensile behavior of asphalt binder.By applying virtual strain,the separation work during asphalt binder tensile failure was calculated.Additionally,a correlation between macroscopic and microscopic tensile behaviors was established.Specifically,a quadrilateral asphalt binder model was generated based on SARA fractions.By applying various combinations of virtual strain loading,the separation work at tensile failure was determined.Furthermore,the impact of strain loading combinations on separation work was analyzed.Normalization was employed to establish the correlation between macroscopic and microscopic tensile behaviors.The results indicated that thermodynamic and classical mechanical indicators validated the reliability of the tetragonal asphalt binder model.The strain loading combination consists of strain rate and loading number.All strain loading combinations exhibited the similar tensile failure characteristic.The critical separation strain was hardly influenced by strain loading combination.However,increasing strain rate significantly enhanced both the maximum traction stress and separation work of the asphalt binder.An increment in the loading number led to a decrease in separation work.The virtual strain combination of 0.5%-80 provided a more accurate representation of the actual asphalt's tensile behavior trend.

Stress evolution and failure process of Brazilian disc under impact

To reveal stress distribution and crack propagation of Brazilian discs under impact loads, dynamic tests were conducted with SHPB (split Hopkinson pressure bar) device. Stress states of specimens were monitored with strain gauges on specimen surface and SHPB bars. The failure process of specimen was recorded by ultra speed camera FASTCAM SA1.1 (675 000 fps). Stress histories from strain gauges offer comprehensive information to evaluate the stress equilibrium of specimen in time and space. When a slowly rising load (with loading rates less than 1 200 N/s for d 50 mm bar) is applied, there is usually good stress equilibrium in specimen. The stress distribution after equilibrium is similar to its static counterpart. And the first crack initiates at the disc center and propagates along the load direction. But with the front of incident wave becoming steep, it is hard for specimens to get to stress equilibrium. The first crack may appear anywhere on the specimen together with multiple randomly distributed secondary cracks. For a valid dynamic Brazil test with stress equilibrium, the specimen will break into two halves neatly. While for tests with stress disequilibrium, missing strap may be found when broken halves of specimens are put together. For those specimens broken up neatly at center but having missing wedges at the loading areas, it is usually subjected to local buckling from SHPB bars.

Failure mechanism and control technology of water-immersed roadway in high-stress and soft rock in a deep mine

Aiming at soft rock ground support issues under conditions of high stress and long-term water immersion, the ground failure mechanism is revealed by taking the deep-water sumps of Jiulong Mine as the engineering background and employing field investigation, tests of rock structure, mechanical properties and mineral composition. The main factors leading to the surrounding rock failure include the high and complex stress state of the water sumps, high-clay content and water-weakened rock, and the unreasonable support design. In this paper, the broken and fractured rock mass near roadway opening is considered as ground small-structure, and deep stable rock mass as ground large-structure. A support technology focusing on cutting off the water, strengthening the small structure of the rock and transferring the large structure of the rock is proposed. The proposed support technology of interconnecting the large and small structures, based on high-strength bolts, high-stiffness shotcrete layer plugging water,strengthening the small structure with deep-hole grouting and shallow-hole grouting, highpretensioned cables tensioned twice to make the large and small structures bearing the pressure evenly,channel-steel and high-pretensioned cables are used to control floor heave. The numerical simulation and field test show that this support system can control the rock deformation of the water sumps and provide technical support to similar roadway support designs.

Macro Meso Response and Stress Wave Propagation Characteristics of MCT High-Voltage Switch Under Shock load

In order to study the dynamic and electrical coupling response characteristics of Metal Oxide Semiconductor Controlled Thyristor(MCT)high-voltage switch under the synergic action of mechanical load and high voltage,the separated Hopkinson pressure bar(SHPB)test system was used to simulate different impact load environments,and combined with the multi-layer high-voltage ceramic capacitor charging and discharging system,the instantaneous electrical signals of MCT high-voltage switch were collected.Combined with numerical simulation and theoretical analysis,the failure mode and stress wave propagation characteristics of MCT high voltage switch were determined.The mechanical and electrical coupling response characteristics and failure mechanism of MCT high voltage switch under dynamic load were revealed from macroscopic and microscopic levels.The results show that the damage modes of MCT high-voltage switches can be divided into non-functional damage,recoverable functional damage,non-recoverable damage and structural damage.Due to the gap between the metal gate and the oxide layer,the insulating oxide layer was charged.After placing for a period of time,the elastic deformation of the metal gate partially recovered and the accumulated charge disappeared,which induced the recoverable functional damage failure of the device.In addition,obvious cracks appeared on both sides of the monocrystalline silicon inside the MCT high-voltage switch,leading to unrecoverable damage of the device.