Fatigue Strength Analysis of Dissimilar Aluminum Alloy TIG Welds

The constant amplitude loading fatigue tests were carried out on the 6061/7075 aluminum alloy TIG fillet welded lap specimens in this study,and the weld seam cross-section hardness was measured.The experimental results show that most specimens mainly failed at the 7075 side weld toes even though the base material tensile strength of 7075 is higher than that of 6061.The maximum stress-strain concentration in the two finite element models is located at the 7075 side weld toe,which is basically consistent with the actual fracture location.The weld zone on the 7075 side experiences severe material softening,with a large gradient.However,the Vickers hardness value on the 6061 side negligibly changes and fluctuates around 70 HV.No obvious defects are found on the fatigue fracture,but a large number of secondary cracks appear.Cracks germinate from the weld toe and propagate in the direction of the plate thickness.Weld reinforcement has a serious impact on fatigue life.Fatigue life will decrease exponentially as the weld reinforcement increases under low stress.It is found that the notch stress method can give a better fatigue life prediction for TIG weldments,and the errors of the predicted results are within the range of two factors,while the prediction accuracy decreases under low stress.The equivalent structural stress method can also be used for fatigue life prediction of TIG weldments,but the errors of prediction results are within the range of three factors,and the accuracy decreases under high stress.

Utilizing complementary therapy to enhance quality of life and reduce stress and fatigue in pediatric cancer patients

The international scientific literature presents still incipient results regarding the management of cancer symptom clusters by oncology nursing,especially in pediatric oncology.This is a promising field of investigation for clinical nurses and researchers,and when it is subsidized by medium-range theories,they co-rroborate the diagnoses and interventions of nursing in oncology,enhancing the science of nursing care.This minireview article aims to discuss the utilizing the hospital clowns as a complementary therapy,to enhance quality of life and reduce stress and fatigue in pediatric cancer patients.Overall,the evidence presented so far pointed out that complementary therapy might help improve the quality of life of pediatric cancer patients,and that complementary therapy usage should be part of a health comprehensive care model,delivering therapeutic approaches that might enhance the mind-body during a pediatric cancer patients’life span.The results of scientific investigations by nurses,particularly those linked to the basic sciences,play a critical role in advancing personalized care in pediatric integrative oncology.

The Association between Problematic Internet Use,Resilience,and Fatigue in First-Year Medical College Students in China:A Moderated Mediation Model

Background:Resilience is crucial for medical college students to thrive in the highly stressful environment of medical education.However,the prevalence of problematic internet use(PIU)in this population may negatively impact their resilience.This study investigated the influence of problematic online gaming(PG)and problematic social media use(PSMU)on the resilience of medical college students in China.Methods:A sample of 5075 first-year medical college students from four Chinese universities was studied.PG served as the independent variable,resilience as the dependent variable,fatigue as the mediator,and PSMU as the moderator.Structural equation modeling was conducted using LISREL 8.80.Additionally,a moderated mediation model was evaluated using the jAMM module in jamovi 2.6.13.Results:The study’s findings revealed significant negative correlations between resilience and the variables of PG,PSMU,and fatigue.Fatigue mediated the relationship between PG and resilience(B=−0.04,95%CI=[−0.05,−0.03]).PSMU moderated the direct relationship between PG and resilience with the interaction term PG×PSMU significant(B=−0.004,t=−6.501,p<0.001)and the first stage(PG→fatigue)of the mediation with PG×PSMU significant(B=0.055,t=8.351,p<0.001).The detrimental effects of PG on resilience were more pronounced among individuals with lower levels of PSMU.Conclusion:This study concluded that addressing PIU,particularly PG,is essential for fostering resilience in medical college students.While PSMU itself is maladaptive,the underlying social media engagement may serve a protective role through social support in mitigating the adverse effects of PG on resilience.

Improving the outcome in leukemia patients by controlling subthreshold depression and cancer-related fatigue

Patients with leukemia often suffer from the combined effects of cancer-related fatigue(CRF)and subthreshold depression,which mutually exacerbate each other in a vicious cycle.In this editorial,we comment on the article by Liu et al,published in the World Journal of Psychiatry.We further elucidate the profound impact of subthreshold depressive symptoms on the experience of CRF and complications in patients with leukemia.This editorial highlights the importance of early identification and treatment of subclinical depression,and advocates for a multidisciplinary and integrated treatment approach that includes social support,psychological interventions,and individualized treatment plans.Future research needs to explore the biological mechanisms underlying the interaction between the two to develop more effective prevention and treatment strategies.

Fatigue characteristics of deep excavation-disturbed jinping marble

Deep rocks encountered in underground engineering are frequently in complex in situ environments and experience both excavation disturbance during construction and cyclic loading throughout the long-term operation. Understanding the fatigue behavior of excavation-disturbed rocks in complex stress environments is critical for assessing the long-term stability of deep rock structures. Hence, an experimental method has been developed to capture the fatigue damage process of rocks while considering the in situ environment and excavation disturbance. Using this method, a series of triaxial fatigue damage experiments were conducted on Jinping deep marble samples from various in situ environments of 100 m, 1000 m, 1800 m, and 2400 m to better understand the variation in fatigue characteristics at different depths. With increasing depth, the samples experienced more cycles and greater fatigue deformation before failure. Further insights were gained into the fatigue damage behavior in terms of stiffness degradation, energy dissipation and irreversible strain accumulation. A decrease in the elastic modulus and an increase in the dissipated energy and irreversible strain exhibit an evolution pattern of initial→stabilization→acceleration, reflecting the nonlinear fatigue process that occurs inside marble. With increasing depth, marble samples have longer fatigue lives but exhibit more significant stiffness loss, energy dissipation and irrecoverable deformation accumulation;thus, evaluating the instability of deep rock structures solely using fatigue life alone is inadequate. Moreover, the previously reported inverted S-shaped evolution of fatigue damage was observed, and it was found that an increase in depth leads to an earlier onset of the accelerated fatigue damage stage with greater dominance of fatigue failure. Based on the nonlinear strain, loading cycle variable and fatigue life, a highly accurate nonlinear fatigue model was developed to describe the complete inverted S-shaped evolution pattern of fatigue damage, which demonstrated excellent practical implications for the theoretical characterization of anisotropic fatigue damage in disturbed Jinping marble.

Frequency Domain Fatigue Evaluation on SCR Girth-Weld Based on Structural Stress

The Steel Catenary Riser(SCR)is a vital component for transporting oil and gas from the seabed to the floating platform.The harsh environmental conditions and complex platform motion make the SCR’s girth-weld prone to fatigue failure.The structural stress fatigue theory and Master S-N curve method provide accurate predictions for the fatigue damage on the welded joints,which demonstrate significant potential and compatibility in multi-axial and random fatigue evaluation.Here,we propose a new frequency fatigue model subjected to welded joints of SCR under multiaxial stress,which fully integrates the mesh-insensitive structural stress and frequency domain random process and transforms the conventional welding fatigue technique of SCR into a spectrum analysis technique utilizing structural stress.Besides,a full-scale FE model of SCR with welds is established to obtain the modal structural stress of the girth weld and the frequency response function(FRF)of modal coordinate,and a biaxial fatigue evaluation about the girth weld of the SCR can be achieved by taking the effects of multi-load correlation and pipe-soil interaction into account.The research results indicate that the frequency-domain fatigue results are aligned with the time-domain results,meeting the fatigue evaluation requirements of the SCR.

A review on the synergism between corrosion and fatigue of magnesium alloys:Mechanisms and processes on the micro-scale

Understanding the interaction between cyclic stresses and corrosion of magnesium(Mg)and its alloys is increasingly in demand due to the continuous expansion of structural applications of these materials.This review is dedicated to exploring the corrosion-fatigue mechanisms of these materials,with an emphasis on microscale processes,and the possibility of expanding current knowledge on this topic using scanning electrochemical techniques.The interaction between fatigue and corrosion of Mg alloys is analyzed by considering the microstructural aspects(grain size,precipitates,deformation twins),as well as the formation of pits.Furthermore,in the case of coated alloys,the role of coating defects in these phenomena is also described.In this context,the feasibility of using scanning electrochemical microscopy(SECM),scanning vibrating electrode technique(SVET),scanning ion-selective electrode technique(SIET),localized electrochemical impedance spectroscopy(LEIS)and scanning Kelvin probe(SKP)methods to study the corrosion-fatigue interaction of Mg alloys is examined.A comprehensive review of the current literature in this field is presented,and the opportunities and limitations of consolidating the use of these techniques to study the microscale processes involved in Mg corrosion-fatigue are discussed.

Impact of comorbid subthreshold depressive symptoms on cancerrelated fatigue and complications in adults with leukemia

BACKGROUND Patients not only experience symptoms caused by cancer but also suffer from the accompanying psychological pain.Therefore,these patients do not have high quality of life.According to the World Health Organization,the incidence of leukemia in China in 2020 was 5.1/100000,the mortality rate was 3.3/100000,and the prevalence rate was 16.7/100000.Therefore,it is important to examine the influence of comorbid subthreshold depressive symptoms on leukemia patients.AIM To determine the impact of comorbid subthreshold depressive symptoms on cancer-related fatigue and complications in leukemia patients,thereby providing a basis for early diagnosis and treatment in clinical practice.METHODS A questionnaire survey was conducted among leukemia patients admitted to a tertiary hospital in Xi'an,Shaanxi Province,China,from August 2022 to December 2023.Patients with a score>16 on the Chinese Classification of Mental Disorders(CCMD-3)and a Hamilton Depression Rating Scale score of 8-17 were classified as the subthreshold depressive group(n=95),while 100 leukemia patients admitted during the same period were classified as the control group.Data were collected using Epidata 3.1 software,and comparisons were made between the two groups regarding general clinical data,the Piper Fatigue Scale(PFS),the Pittsburgh Sleep Quality Index(PSQI),the Numeric Rating Scale for pain assessment,laboratory indicators,and the occurrence of complications.RESULTS In this survey,120 leukemia patients with depression were preliminarily screened,95 patients with subthreshold depression were ultimately selected as the subthreshold depression group,and 100 leukemia patients admitted during the same period were enrolled as the normal group.Comparison of basic clinical data between the two groups revealed no significant differences in age,sex,body mass index,cognitive function,or comorbidity with other chronic diseases.However,there were statistically significant differences in the use of radiotherapy and regular exercise between the two groups(P<0.05).Comparisons of scales and laboratory indicators revealed no significant differences in albumin or PSQI scores between the two groups,but there were statistically significant differences in pain scores,PSQI scores,PFS scores,hemoglobin levels,and C-reactive protein levels(P<0.05).Spearman’s correlation analysis indicated that cancer-related fatigue was correlated with age,hemoglobin levels,C-reactive protein levels,pain,and regular exercise among leukemia patients with subthreshold depression.Multivariate regression analysis revealed that advanced age,combined radiotherapy,pain,and low hemoglobin levels were risk factors for cancer-related fatigue in leukemia patients with comorbid subthreshold depression,while regular exercise was a protective factor against cancer-related fatigue.Follow-up comparisons revealed a significantly lower overall incidence of complications in the control group(4%)than in the depressive group(24.21%;P<0.001).CONCLUSION Leukemia patients with comorbid subthreshold depressive symptoms experience more severe cancer-related fatigue and a higher incidence of complications.These findings may be related to advanced age,combined radiotherapy,pain,and low hemoglobin levels,while regular exercise may effectively alleviate symptoms.

Correlation of objective and subjective sleep parameters with fatigue and depression in kidney transplant recipients

Objective:Sleep quality in kidney transplant recipients is closely associated with symptoms of fatigue and depression.Although subjective assessment tools like the Pittsburgh Sleep Quality Index and the Richards-Campbell Sleep Questionnaire(RCSQ)are widely used to evaluate sleep quality,there is a lack of studies utilizing polysomnography for objective evaluation.This study aims to investigate the correlation between sleep quality,fatigue,and depression in kidney transplant recipients using both subjective and objective methods,providing scientific evidence for improving their quality of life.Methods:The cross-sectional study conveniently sampled 50 kidney transplant recipients from a transplant center in a general hospital between August 2018 and March 2020.Subjective and objective sleep parameters were evaluated using the RCQS and polysomnography,respectively.The Fatigue Severity Scale was used to assess fatigue,and the Hamilton Depression Scale was employed to measure depression levels.Results:A lower proportion of rapid eye movement(REM)sleep was associated with increased fatigue.Additionally,higher wake time percentages and poorer sleep quality were significantly correlated with greater depression severity.Conclusion:This study underscores the critical importance of effectively managing sleep quality in kidney transplant recipients and addressing their fatigue and depression symptoms.These findings lay a foundation for developing targeted nursing and therapeutic strategies.

Optimizing Multi-Row Cam Roller Bearing for Long Fatigue Life of Hydraulic Motors

Cam-lobe radial-piston hydraulic motors are widely used as rotation driving units for various marine machinery owing to their ultrahigh output torque(more than 100 kN m).A multi-row cam roller bearing(MCRB)is the key component that directly determines the fatigue life of a cam-lobe radial-piston hydraulic motor.However,compact geometry and complex loads render MCRB susceptible to fatigue failure,highlighting the need for an optimized MCRB to achieve longer fatigue life and higher reliability.Therefore,this study proposes an innovative geometry optimization method for an MCRB to improve its fatigue life.In this method,a quasi-static model was developed to calculate the load distribution,with the fatigue life of the MCRB calculated using both basic dynamic loading and load distribution.Subsequently,a genetic algorithm was used to obtain the optimized geometry parameters,which significantly improved the fatigue life of the MCRB.Finally,a loading test was conducted on a hydraulic motor installed with both the initial and optimized MCRB to validate the effectiveness of the proposed optimization method.This study provides a theoretical guideline for optimizing the design of MCRB,thereby increasing the fatigue life of hydraulic motors.

Microstructure evolution and enhanced fatigue behavior in the Mg-10Li-5Zn-0.5Er alloys micro-alloyed with Yb

In this paper,(0.2-1 wt%)Yb was added to improve the tensile properties and high-cycle fatigue behavior of the as-cast and as-extruded Mg-10Li-5Zn-0.5Er alloys.It is found that Yb mainly affects the mechanical properties of the alloy by changing the grain size,type and morphology of the second phases.Yb mainly exists in the formation of Mg_(2)Yb and Mg-Zn-Yb phases in the metallographic structure.With the addition of Yb,the grains are refined and these Yb-containing phases replace the large-sized MgLiZn phase to be enriched at the grain boundaries.While the addition of excess Yb reduces the number of small-sized MgLiZn phases in the grain,thus reducing the alloys’mechanical performance.After extrusion,the small-sized MgLiZn phase is refined and the number increases,which effectively improves the tensile and fatigue strength of the alloy.The fatigue strength is mainly affected by the number and morphology of the second phase,positively correlated with the strength.Balanced in grain size and number and size of second phases,the extruded alloy with 0.2Yb added exhibits excellent mechanical properties with the yield strength,ultimate tensile strength and elongation of 292 MPa,303 MPa and 11.7%,and an fatigue strength of 130 MPa.

Efficacy of ginseng-based Renshenguben oral solution for cancer-related fatigue among patients with advanced-stage hepatocellular carcinoma:A prospective multicenter cohort study

Background:Cancer-related fatigue(CRF)is a common and debilitating symptom experienced by patients with advanced-stage cancer,especially those undergoing antitumor therapy.This study aimed to evaluate the efficacy and safety of Renshenguben(RSGB)oral solution,a ginseng-based traditional Chinese medicine,in alleviating CRF in patients with advanced hepatocellular carcinoma(HCC)receiving antitumor treatment.Methods:In this prospective,open-label,controlled,multicenter study,patients with advanced HCC at BCLC stage C and a brief fatigue inventory(BFI)score of≥4 were enrolled.Participants were assigned to the RSGB group(RSGB,10 mL twice daily)or the control group(with supportive care).Primary and secondary endpoints were the change in multidimensional fatigue inventory(MFI)score,and BFI and functional assessment of cancer therapy-hepatobiliary(FACT-Hep)scores at weeks 4 and 8 after enrollment.Adverse events(AEs)and toxicities were assessed.Results:A total of 409 participants were enrolled,with 206 assigned to the RSGB group.At week 4,there was a trend towards improvement,but the differences were not statistically significant.At week 8,the RSGB group exhibited a significantly lower MFI score(P<0.05)compared to the control group,indicating improved fatigue levels.Additionally,the RSGB group showed significantly greater decrease in BFI and FACT-Hep scores at week 8(P<0.05).Subgroup analyses among patients receiving various antitumor treatments showed similar results.Multivariate linear regression analyses revealed that the RSGB group experienced a significantly substantial decrease in MFI,BFI,and FACT-Hep scores at week 8.No serious drug-related AEs or toxicities were observed.Conclusions:RSGB oral solution effectively reduced CRF in patients with advanced HCC undergoing antitumor therapy over an eight-week period,with no discernible toxicities.These findings support the potential of RSGB oral solution as an adjunctive treatment for managing CRF in this patient population.

Damage Evolution of Ballastless Track Concrete Exposed to Flexural Fatigue Loads:The Application of Ultrasonic Pulse Velocity,Impact-echo and Surface Electrical Resistance Method

In order to clarify the fatigue damage evolution of concrete exposed to flexural fatigue loads,ultrasonic pulse velocity(UPV),impact-echo technology and surface electrical resistance(SR) method were used.Damage variable based on the change of velocity of ultrasonic pulse(Du) and impact elastic wave(Di)were defined according to the classical damage theory.The influences of stress level,loading frequency and concrete strength on damage variable were measured.The experimental results show that Du and Di both present a three-stages trend for concrete exposed to fatigue loads.Since impact elastic wave is more sensitive to the microstructure damage in stage Ⅲ,the critical damage variable,i e,the damage variable before the final fracture of concrete of Di is slightly higher than that of Du.Meanwhile,the evolution of SR of concrete exposed to fatigue loads were analyzed and the relationship between SR and Du,SR and Di of concrete exposed to fatigue loads were established.It is found that the SR of concrete was decreased with the increasing fatigue cycles,indicating that surface electrical resistance method can also be applied to describe the damage of ballastless track concrete exposed to fatigue loads.

Thermal fatigue and wear of compacted graphite iron brake discs with various thermomechanical properties

The increase in payload capacity of trucks has heightened the demand for cost-effective yet high performance brake discs.In this work,the thermal fatigue and wear of compacted graphite iron brake discs were investigated,aiming to provide an experimental foundation for achieving a balance between their thermal and mechanical properties.Compacted graphite iron brake discs with different tensile strengths,macrohardnesses,specific heat capacities and thermal diffusion coefficients were produced by changing the proportion and strength of ferrite.The peak temperature,pressure load and friction coefficient of compacted graphite iron brake discs were analyzed through inertia friction tests.The morphology of thermal cracks and 3D profiles of the worn surfaces were also discussed.It is found that the thermal fatigue of compacted graphite iron discs is determined by their thermal properties.A compacted graphite iron with the highest specific heat capacity and thermal diffusion coefficient exhibits optimal thermal fatigue resistance.Oxidization of the matrix at low temperatures significantly weakens the function of alloy strengthening in hindering the propagation of thermal cracks.Despite the reduced hardness,increasing the ferrite proportion can mitigate wear loss resulting from low disc temperatures and the absence of abrasive wear.

A Non-Intrusive Stochastic Phase-Field for Fatigue Fracture in Brittle Materials with Uncertainty in Geometry and Material Properties

Understanding the probabilistic nature of brittle materials due to inherent dispersions in their mechanical properties is important to assess their reliability and safety for sensitive engineering applications.This is all the more important when elements composed of brittle materials are exposed to dynamic environments,resulting in catastrophic fatigue failures.The authors propose the application of a non-intrusive polynomial chaos expansion method for probabilistic studies on brittle materials undergoing fatigue fracture when geometrical parameters and material properties are random independent variables.Understanding the probabilistic nature of fatigue fracture in brittle materials is crucial for ensuring the reliability and safety of engineering structures subjected to cyclic loading.Crack growth is modelled using a phase-field approach within a finite element framework.For modelling fatigue,fracture resistance is progressively degraded by modifying the regularised free energy functional using a fatigue degradation function.Number of cycles to failure is treated as the dependent variable of interest and is estimated within acceptable limits due to the randomness in independent properties.Multiple 2D benchmark problems are solved to demonstrate the ability of this approach to predict the dependent variable responses with significantly fewer simulations than the Monte Carlo method.This proposed approach can accurately predict results typically obtained through 105 or more runs in Monte Carlo simulations with a reduction of up to three orders of magnitude in required runs.The independent random variables’sensitivity to the system response is determined using Sobol’indices.The proposed approach has low computational overhead and can be useful for computationally intensive problems requiring rapid decision-making in sensitive applications like aerospace,nuclear and biomedical engineering.The technique does not require reformulating existing finite element code and can perform the stochastic study by direct pre/post-processing.

Low-cycle fatigue behavior of solutionized and aged WE43 magnesium alloys at room temperature

The low-cycle fatigue behavior of solutionized(T4)and aged(T6)WE43 magnesium alloys was studied at room temperature.The total strain amplitudes(△ε_(t)/2)were 0.4%,0.5%,0.6%,0.7%and 1.0%.Detailed microstructure evolution was characterized by scanning electron microscope(SEM),electron backscattered diffraction(EBSD)and transmission electron microscopy(TEM).The results showed that plastic strain amplitude decreased with the increasing cycle number in T4 alloy,which is due to the dense persistent slip bands(PSBs)and dynamic precipitates hinderingdislocation slip.In contrast,the plastic strain amplitude increases gradually in T6 alloy,which is attributed to the enhanced activation of pyramidal slip.The low-cycle fatigue life of T6 alloy with larger fatigue ductility coefficient is longer than that of T4 alloy.The Coffin-Manson model can accurately predict the fatigue life of T4 and T6 alloys compared to Jahed-Varvani(JV)energy model.For T4 alloy,the fatigue damage mechanism was dominated by basal slip.For T6 alloy,the enhanced pyramidal slip plays an important role to accommodate plastic deformation.

Improving fatigue properties of normal direction ultrasonic vibration assisted face grinding Inconel 718 by regulating machined surface integrity

Fatigue properties are crucial for critical aero-engine components in extreme serviceenvironments,which are significantly affected by surface integrity(SI)indexes(especially surface topography,residual stressσ_(res),and microhardness)after machining processes.Normal-direction ultrasonic vibration-assisted face grinding(ND-UVAFG)has advantages in improving the machinability of Inconel 718,but there is a competitive relationship between higher compressiveσ_(res)and higher surface roughness R_(a)in affecting fatigue strength.The lack of a quantitative relationship between multiple SI indexes and fatigue strength makes theindeterminacy of a regulatory strategy for improving fatigue properties.In this work,a model of fatigue strength(σ_f)_(sur)considering multiple SI indexes was developed.Then,high-cycle fatigue tests were carried out on Inconel 718 samples with different SI characteristics,and the influence of ND-UVAFG process parameters on SI was analyzed.Based on SI indexes data,the(σ_f)_(sur)distribution in the grinding surface layer for ND-UVAFG Inconel 718 samples was determined using the developed model,and then the fatigue crack initiation(FCI)sites were furtherpredicted.The predicted FCI sites corresponded well with the experimental results,therebyverifying this model.A strategy for improving the fatigue life was proposed in this work,which was to transfer the fatigue source from the machined surface to the bulk material by controlling the SI indexes.Finally,a critical condition of SI indexes that FCI sites appeared on the surface or in bulk material was given by fitting the predicted results.According to the critical condition,an SI field where FCI sites appeared in the bulk material could be obtained.In this field,thefatigue life of Inconel 718 samples could be improved by approximately 140%.

Fatigue Resistance of RCA Modified Asphalt Based on Dielectric Properties

In order to study the anti-fatigue performance of RCA modified asphalt (RMA),the performance of RMA and 90#matrix asphalt with different modifier content were measured by asphalt penetration,ductility,softening point,Brookfield viscosity,rheological index,infrared spectrum and dielectric constant test.This paper discusses the changes of asphalt basic indexes,fatigue properties and asphalt components based on dielectric properties under different modifier contents,and analyzes the grey correlation degree between components and asphalt pavement performance indexes.The results show that the optimum content of RCA modifier is 16.7%of the asphalt quality according to the penetration,ductility,softening point,Brockfield viscosity,viscosity temperature curve and fatigue life.In the phase angle-strain curve,there is disorder in the latter part of the curve.According to the strain (ε_(d)) corresponding to the disorder point,a new fatigue failure criterion is proposed and proved.Based on the new asphalt fatigue failure criterion,the fatigue prediction model of asphalt mixture is improved,and the fatigue life predicted by the improved fatigue model is compared with the fatigue life obtained by four-point bending fatigue test.The results show that the proposed new asphalt fatigue failure criterion is reasonable,and the fatigue life predicted by the improved asphalt mixture fatigue prediction model is accurate.The research method of classifying asphalt components based on dielectric properties is simple and effective,and the components have a high correlation with the road performance of base asphalt and modified asphalt.

Effects of orientation on the fatigue crack growth behaviors of the ZK60 magnesium alloy in air and PBS

Strong anisotropic corrosion and mechanical properties caused by specimen orientations greatly limit the applications of wrought magnesium alloys.To investigate the influences of specimen orientation,the corrosion tests and(corrosion)fatigue crack growth tests were conducted.The rolled and transverse surfaces of the materials show distinct corrosion rate differences in the stable corrosion stage,but the truth is the opposite for the initial stage of corrosion.In air,specimen orientations have a significant influence on the plastic deformation mechanisms near the crack tip,which results in different fatigue fracture surfaces and cracking paths.Compared with R-T specimens,N-T specimens show a slower fatigue crack growth(FCG)rate in air,which can be attributed to crack closure effects and deformation twinning near the crack tip.The corrosion environment will not significantly change the main plastic deformation mechanisms for the same type of specimen.However,the FCG rate in phosphate buffer saline(PBS)is one order of magnitude higher than that in air,which is caused by the combined effects of hydrogen-induced cracking and anodic dissolution.Owing to the similar corrosion rates at crack tips,the specimens with different orientations display close FCG rates in PBS.

Anti-fatigue activity and mechanism of crocetin loaded nanoliposome in acute exercise-treated mice

Crocetin displays strong antioxidant,anti-inflammatory and anti-depression activity which is promising to relieve symptoms of fatigue.As a carotenoid,crocetin is difficult to dissolve in water and highly unstable against many environmental factors.Nanoliposome is used to encapsulate crocetin to improve its water dispersion.In the present study,the antifatigue activities and potential mechanism of crocetin loaded nanoliposome(CLN)was extensively investigated.The potential antifatigue pathway of CLN was analyzed.Furthermore,impact of CLN on the gut microbiota structure was examined which contributes to its antifatigue functions.CLN significantly increases exhaustive swimming time of fatigue mice,decreases the blood contents of lactic,blood urea nitrogen(BUN)and malondialdehyde(MDA).At the same time,CLN improves the activity of glutathione peroxidase(GSH-Px)and succinate dehydrogenase(SDH)enzyme,attenuates the oxidant stress in mice.CLN activates the adenosine monophosphate-activated kinase(AMPK)/peroxisome proliferator-activated receptor gamma coactivator-1α(PGC-1α)signaling pathway of fatigue mice,increases the mRNA expression of ATP synthase.It also increases mRNA expression of mitochondrial transcription factor A(TFAM)which promotes mitochondrial biogenesis.Additionally,CLN ameliorates the gut microbiota structure by increasing the abundance of genus such as Lactobacillus in fatigue mice.In summary,CLN exerts strong anti-fatigue properties by decreasing the oxidant stress and the contents of harmful metabolites,augmenting the production of ATP,and potentially ameliorating the gut microbiota structure.