Formation and corrosion behavior of Fe-based amorphous metallic coatings prepared by detonation gun spraying

Amorphous metallic coatings with a composition of Fe48Cr15Mo14C15B6Y2 were prepared by detonation gun spraying process. Microstructural studies show that the coatings present a densely layered structure typical of thermally sprayed deposits with the porosity below 2%. Both crystallization and oxidation occurred obviously during spraying process, so that the amorphous fraction of the coatings decreased to 54% compared with fully amorphous alloy ribbons of the same component. Corrosion behavior of the amorphous coatings was investigated by electrochemical measurement. The results show that the coatings exhibit extremely wide passive region and low passive current density in 3.5% NaCl (mass fraction) and 1 mol/L HCl solutions, which illustrates excellent ability to resist localized corrosion.

Microstructure of Cu-based Amorphous Composite Coatings on AZ91D Magnesium Alloy by Laser Cladding

To improve the sliding wear resistance of AZ91D magnesium alloy, Cu-based amorphous composite coatings made of CuaTTi34Zr11Nis and Cu47Ti34Zr11Ni8＋20 wt pct SiC powders were fabricated on AZ91D magnesium alloy by laser cladding, respectively. SEM （scanning electron microscopy）, EDS （energy dispersive X-ray spectroscopy）, XRD （X-ray diffraction） and TEM （transmission electron microscopy） techniques were employed to study the phases of the coatings. The results show that the coatings mainly consist of amorphous phase and different intermetallic compounds. The reason of formation of amorphous phase and the function of SiC particles were explained in details.

Molybdenum based amorphous and nanocrystalline coatings prepared by high velocity oxy-fuel spraying

The high velocity oxy-fuel(HVOF) based thermal spray process has developed as a potential advantageous approach for fabricating various kinds of functional coatings.In this article,the coatings of Mo-based alloy were synthesized using the HVOF process.The microstructure and the mechanical properties of the HVOF-processed coatings were investigated using SEM,TEM,XRD,and hardness and wear tests.Annealing treatment was applied to the as-sprayed coatings to develop the microstructure and its effect on the microstructure and mechanical properties of the coatings was examined.It is found that the HVOF-processed Mo-based alloy coatings are comprised of an amorphous splat matrix embedded with nano-sized crystalline particles.Annealing at temperatures over 950 ℃ results into crystallization of the amorphous matrix.The mechanical properties of the as-sprayed coatings are enhanced with annealing temperature up to 750 ℃ and from 950 to 1050 ℃,keeps constant between 750 and 950 ℃,and reduce over 1050 ℃.The change of the mechanical property with the microstructure was illustrated in the study.

FORMATION OF GRADIENT COATING OF Fe-BASED ALLOY WITH RARE EARTHS BY PLASMA SURFACING

A gradient coating of Fe-based alloy was manufactured with rare earths (RE) by plasma surfacing on Q235 steel substrate. The coatings were studied by using X-ray diffraction(XRD), scanning electron microscope(SEM), differential thermal analyzer(DTA), and electron probe micro-analyzer (EPMA). The results show that the phases of the two kinds of coatings(with and without RE) both include α-Fe, Fe7C3, Fe3C, Cr2B, Fe2B and FeB. The microstructure of F314 coating is mainly hypereutectic, the pro-phases Cr7C3 and Cr2B are loose, crassi, spiculate and contain microcracks. The brittleness of the coating is high, and the average hardness is 787 HV. When 0.8wt% RE was added into the F314 alloy, the microstructure varied from hypoeutectic to hypereutectic continuously, The hardness appears as gradient distribution with the highest value of 773 HV, meanwhile, the brittleness decreases significantly. The formation of gradient structure depends on the fallowing factors: (i) the conversion of RE. The addition of RE lowers the elements point and Fe-C eutectic temperature, thus the base metal melting acutely. (ii) the heating of plasma arc. Graded temperature results in directional solidification, thus the gradient structure forms easily. The main reasons for the hardness decrease with RE addition in the alloy are the ratio of hard phase lowering and the hardness of the hard phase decreasing.

Formation and mechanical properties of ductile Fe-based amorphous alloys using a cast iron with minor addition of B and Al

Fe-based amorphous alloys with ductility were synthesized using the commercial cast iron QT50 (denoted as QT) with the combining minor addition of B and Al by single roller melt-spinning. The melt-spun (QT1-xBx)99Al1 (x is from 0.006wt% to 0.01wt%) amorphous alloys exhibit onset crystallization temperatures and Curie temperatures of 759-780 and 629-642 K respectively, and whi- ch increase with B content. The amorphous ribbons are ductile and can be bent 180° without breaking. With the increase in B content from 0.006wt% to 0.01wt%, the Vickers microhardness of the amorphous alloys increases from Hv 830 to Hv 1110. The effects of the additional B and Al elements on the glass forming ability and mechanical properties were also discussed.

Effects of C/B4 C ratio on microstructure and property of Fe-based alloy coatings reinforced with in situ synthesized TiB2 -TiC

The Fe-based alloy coatings reinforced with in situ synthesized TiB2-TiC were prepared on Q235 steel by reactive plasma cladding using Fe901 alloy, Ti, B4C, and graphite （C） powders us raw materials. The effects of C/B4C weight percentage ratio （0 - 1. 38 ） on the microstructure , microhardness , and wet sand abrasion resistance of the coatings were investigated. The results show that the coatings consist of （ Fe, Cr ） solid solution, TiC, TiB2, Ti8C5 , and Fe3 C phases. The decrease of C/B4 C ratio is propitious to the formation of TiB2 and Tis C5. Increasing the C/B4 C ratio can help to refine the microstructure of the coatings. However, the microhardness of the middle-upper of the coatings and the wet sand abrasion resistance of the coatings degenerate with the increase of C/B4C ratio. The coating exhibits the best wet sand abrasion resistance at C/BaC =0 and its average mass loss rate per unit wear distance is 0. 001 2%/m. The change of the wet sand abrasion resistance of the coatings with the C/B4C ratio can be mainly attributed to the combined action of the changes of microhardness and the volume percentage of the ceramic reinforcements containing titanium in the coatings.

Wear Properties of Plasma Transferred Arc Fe-based Coatings Reinforced by Spherical WC Particles

Fe-based coatings reinforced by spherical WC particles were produced on the 304 stainless steel by plasma transferred arc(PTA) to enhance the surface wear properties. Three different Fe/WC composite powder mixtures containing 0 wt%, 30 wt%, and 60 wt% of WC were investigated. The microstructure and phase composition of the Fe/WC composite PTA coatings were evaluated systemically by using scanning electron microscope(SEM) and X-ray diffraction(XRD). The wear properties of the three fabricated PTA coatings were investigated on a BRUKER UMT TriboLab. The morphologies of the worn tracks and wear debris were characterized by using SEM and 3 D non-contract profiler. The experimental results reveal that the microhardness on the cross-section and the wear resistance of the fabricated coatings increase dramatically with the increasing adding WC contents. The coating containing 60 wt% of WC possesses excellent wear resistance validated by the lower coefficients of friction(COF), narrower and shallower wear tracks and smaller wear rate. In the pure Fe-based coating, the main wear mechanism is the combination of adhesion and oxidative wear. Adhesive and two-body abrasive wear are predominated in the coating containing 30 wt% of WC, whereas threebody abrasion wear mechanism is predominated in the coating containing 60 wt% of WC.

Hot-press sintering of MA Fe-based nanocrystalline/amorphous soft magnetic powder

Microstructures and magnetic properties of Fe84Nb7B9,Fe80Ti8B 12 and Fe32Ni36（Nb/V）7Si8B17 powders and their bulk alloys prepared by mechanical alloying（MA） method and hot-press sintering were studied. The results show that: 1) After MA for 20 h,nanocrystalline bcc singl e phase supersaturated solid solution forms in Fe84-Nb7B9 and Fe8 0Ti8B12 alloys,amorphous structure forms in Fe32Ni36Nb7 Si8B17 alloy,duplex microstructure composed of nanocrystalline γ- （FeNi） supersaturated solid solution and trace content of Fe2B phase forms in Fe32Ni36-V7Si8B17 alloy. 2) The decomposition process of supersaturated solid solution phases in Fe84Nb7B9 and Fe80Ti8B 12 alloys happens at 710780 ℃,crystallization reaction in Fe （32）Ni36Nb7Si8B17 alloy happens at 530 ℃（the temperature of peak value） and residual amorphous crystallized further happens at 760 ℃ （the temperature of peak value）,phase decomposition process of supersaturated solid solution at 780 ℃ （the temperature of peak value） and crystallization reaction at 431 ℃ （the temperature of peak value） happens in Fe32Ni36V7S i8B17 alloy. 3) under 900 ℃,30 MPa,（0.5 h） hot-press sintering conditions,bulk alloys with high relative density（94.7%95.8%） can be ob tained. Except that the grain size of Fe84Nb7B9 bulk alloy is large,s uperfine grains （grain size 50200 nm） are obtained in other alloys. Exc ept that single phase microstructure is obtained in Fe80Ti8B12 bul k alloy,multi-phase microstructures are obtained in other alloys. 4) The magne tic properties of Fe80Ti8B12bulk alloy（Bs=1.74 T,Hc= 4.35 kA/m） are significantly superior to those of other bulk alloys,which is r elated to the different phases of nanocrystalline or amorphous powder formed dur ing hot-press sintering process and grain size.

Fracture Behaviour of Laser Clad Fe-and Ni-base Alloy Coatings on a Cast Iron under SEMI Loading

Laser cladding technique has been applied to renovate some partially-damaged (or worn) components with Fe, Ni, Co-base alloys, hence to improve their hardness values and wear resistance successfully in previous reports. But for some punching or shearing cast iron dies damaged or worn in automobile manufacture, the renovated surfaces also bear some impact loading. Therefore, a small-energy and multi-impact (SEMI) test was designed to investigate the fracture behaviour of renovated cast iron dies achieved by laser cladding of Fe and Ni-base alloys under SEMI loading to meet above requirement. observations show that the fracture took place in the substrate near to the substrate/coating interface rather than at the interface. The tempering temperature has a great influence on the cycles to fracture of laser-clad samples under SEMl loading, i.e. the low tempering temperature of 300℃ gives a maximum cycle to fracture, while a higher tempering temperature of 400℃ has a minimum. Furthermore, the fracture mechanism has also been discussed in present study

Formation mechanism of amorphous Ni-Fe-P alloys by electrodeposition

The formation mechanism of the amorphous Ni-Fe-P coating was studied by analysis of the forming thermodynamics, dynamics, and crystallography of the amorphous alloy. The results show that, in the initial stage of deposition a thin 'crystal epitaxial growth' layer first forms, and then transforms to amorphous gradually. The cross section in Ni-Fe-P coatings by electrolytic etching exhibits a banded structure of alternate dark and light bands. It is proposed that the banded structure is caused by a change in the P content with thickness,which is due to alternated depletion and enrichment of [OH-] in the diffusion layer resulting from the generation and evolution of hydrogen gas. The amorphous Ni-Fe-P coating will be formed in proper composition, high nucleation rate and strongly hindered growth of the crystal nucleus. Amorphous Ni-Fe-P alloys form as islands, and grow up by layer.

Stability of electrodeposited amorphous Ni-Fe-P alloys

The stability of the electrodeposited amorphous Ni-Fe-P alloys was studied by DTA,DSC,XRD and improved four-ball wear tester in order to clear its applied scope.The results show that the element content has influence on the stability of amorphous Ni-Fe-P alloy,in which the crystallization temperature increases with Fe content,and the increase of P content delays the appearance of stable crystallization phases and recrystallization.There exist 6 exothermal reactions during heating the amorphous Ni69Fe8P23 alloy continuously.The activation energies of exothermal reactions at 248,303,322,350,376 and 442 ℃ are 131.5,111.6,237.8,253.6 and 238.5 kJ/mol,respectively.The amorphous Ni60Fe22P18 alloy crystallizes when the heating temperature is beyond 250 ℃.The stable crystallization phases consist of Ni(Fe)and Ni3P-type compounds Ni3P,Fe3P,(Fe,Ni)3P.The pressure and fraction have influence on the stability of amorphous alloy.Rubbing above the critical pressure crystallization will take place on the fractional surface.The crystallization phases due to pressure and fraction are different from those due to heating.It is the crystallization that increases the wear resistance of Ni-Fe-P coating under higher pressure.

Wear mechanism of electrodeposited amorphous Ni-Fe-P alloys

The wear mechanism of amorphous Ni-Fe-P coating was discussed. The wear resistance of the amorphous Ni-Fe-P coatings was tested on a Timken wear apparatus, and the wear track of the amorphous Ni-Fe-P coatings as-deposited and heated at various temperatures was observed by SEM. The results show that the wear resistance reaches a maximum value at NaHPO2·H2O concentration of 5 g/L, and heating at 400 ℃. The wear mode of the coating will change with the heating temperature increasing from pitting+plowing at 200 ℃ to pitting at 400 ℃, and to plowing at 600 ℃. The pits on the worn surface of the amorphous Ni-Fe-P coating result from the tribo-fatigue fracture. The cracks of spalling initiate at pits and propagate at certain angle with the sliding direction on surface, and then extend into sub-surface along the poor P layers or the interface between layers. Finally under repeated action of the stress in the rubbing process the cracks meet and the debris forms. The generation of the pits and spalling is related with the internal stress, brittleness and layer structure of the amorphous Ni-Fe-P coating.

Preparation of Plate Fe_(60)Co_8Zr_(10)Mo_5W_2B_(15) Bulk Amorphous Alloy and Its Fracture Toughness

With processes of arc melting, inductive melting and copper mold suction casting, a plate Fe-based bulk amorphous alloy Fe_(60)Co_8Zr_(10)Mo_5W_2B_(15) with a thickness of 1mm was prepared. The surfaces and fractures of the cast bulk amorphous alloy were agleam and with typical metallic luster. The glass transition temperature(T_g), supercooled liquid region(△T_x)and reduced glass transition temperature(T_(rg))of the prepared Fe-based amorphous alloy are 884 K,63 K, and 0.611 respectively. The fracture toughness of the cast bulk amorphous alloy is at the level of 1.6 MPa·m^(1/2).

INFLECTION OF COERCIVITY DURING LOCAL CRYSTALLIZATION OF Fe-Si-B AMORPHOUS ALLOYS

An inflection hehaviour was revealed during isothermal annealing under the observation of transition of the coercivity of Fe-Si-B amorphous alloys during local crystallization.It may be interpreted by the transition of α-Fe grain precipitated from single to multiple domain, Thus,the theoretical expression of H_0-t_a may be derived.The plot of expression H_0-t_a calcu- lated well represents the feature of the experimental curve.

High-pressure sintering and magnetic properties of Fe_(86)Zr_(11-x)Nb_xB_3(x=5.5, 6) amorphous alloys

The thermal stability of milling Fe86Zr11-xNbxB3（x=5.5, 6） melt-spun strip powders and the influence of high-pressure sintering conditions on phase component and grain size of bulk alloys were investigated by X-ray diffractometry（XRD）, differential scanning calorimetry（DSC） and scanning electron microscopy（SEM）. The results show that milling melt-spun powder remains in the amorphous state, and the crystallization temperature of which is 480530℃, the apparent activation energy Ep of crystallization process is 294.1219.5kJ/mol. The increasing Nb content can increase crystallization temperature and decrease Ep. Under the sintering conditions of 5.5GPa/3min, when Pw is 1150W, single phase α-Fe nanocrystalline （20.626.7nm） bulk alloy with relative density higher than 99.0% can be obtained. Under the sintering conditions of 5.5GPa/1150W/3min, the magnetic properties of these nanocrystalline bulk alloys are Fe86Zr5.5Nb5.5B3 alloy, Bs=1.15T, Hc=5.08kA·m-1; Fe86Zr5Nb6B3 alloy, Bs=1.26T, Hc=4.27kA·m-1.

Development and Oxidation Behavior of Al-Cu-Fe Quasicrystalline Coating on Ti Alloy

An oxidation resistant Al-Cu-Fe quasicrystalline coating was fabricated on substrate of Ti alloy by low pressure plasma spraying (LPPS) method. As-sprayed Al-Cu-Fe coating has a rapidly solidified lamellar microstructure consisting of quasicrystalline phase and crystalline phase. The formation of quasicrystalline coating is related to the annealing. The results from the ox!dat!on experiments showed that Al-Cu-Fe quasicrystalline coating improved the oxidation resistance of Ti-base alloys. During the oxidation period there is no evident spallation of the coating from the substrate. Oxide formed on the surface of Al-Cu-Fe quasicrystalline coating after oxidation consisted of Al2O3. Oxidation occurs Ieading to a change of concentration and phase transformation in the coating surface. Selective oxidation of AI transforms the quasicrystalline phase into the phase.

A PASSIVATION STUDY OF Ti-MODIFIED Fe—BASE ALLOY SYNTHESIZED BY MAGNETRON SPUTTERING TECHNIQUE

A set of fracture device was designed on the basis of traditional scratching-electrode technology and used to study the passivation process of two magnetron-sputtered stainless sleel coatings (amorphous and crystalline struture). The results of fracture tests in 3.5 % NaCl aqueous solution show that the amorphous alloy has a high bare surface reactivity and a high passive rate in comparison with the crystalline alloy. The effect of structure on corrosion resistance is also discussed. The excellent corrosion resistance of amorphous alloy is considered to be partly attributed to its great passivation ability.

Microstructure and Frictional Behavior of Fe-based Amorphous Metallic Coatings Prepared by Atmospheric Plasma Spraying

Amorphous metallic coatings with a composition of Fe48Cr15Mo14C15B6Y2 were prepared by means of atmospheric plasma spraying (APS) process under different conditions. The microstructure and frictional behavior were characterized simultaneously in this article. The results show that the as-deposited coatings consist of amorphous matrix and some precipitated nanocrystals, while the amorphous fraction and particle deformation as well as crystallization mechanism are significantly sensitive to the spraying parameters. The amorphous coatings express high microhardness and excellent wear resistance under dry frictional wear condition, which attributes to the inherent characteristic of amorphous phase and the dispersion strengthening of precipitated nanocrystals. The dominant wear mechanism of the amorphous coatings is fatigue wear accompanying with oxidative wear. In addition, the microhardness and wear resistance of the amorphous coatings were improved by optimizing spraying parameters, owing to the effect of both structural character and proper proportional of amorphous and nanocrystals fraction.

Microstructure and Mechanical Properties of Fe-based Amorphous Composite Coatings Reinforced by Stainless Steel Powders

In this study,a few Fe-based amorphous matrix composite coatings reinforced with various portions(4,8 and16 vol.%) of 31 6L stainless steel powders have been successfully produced through high velocity oxy-fuel(HVOF) spraying.The microstructure of the composite coatings was systematically characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The main structure of composite coatings remained amorphous while 31 6L stainless steel splats were distributed homogeneously in the amorphous matrix and well connected with surrounding amorphous phase.Bonding strength of coatings to the substrate was determined by 'pull-off' tensile tests.The results revealed that the31 6L stainless steel phase effectively improved the bonding strength of amorphous coatings,which is mainly contributed by the strong metallurgical bonding between stainless steel and amorphous splats.The addition of31 6L stainless steel also enhanced the ductility and fracture resistance of the coatings due to the ductile stainless steel phases,which can arrest crack propagation and increase energy dissipation.

Microstructure and Wear Properties of Fe-based Amorphous Coatings Deposited by High-velocity Oxygen Fuel Spraying

Fe-based powder with a composition of Fe_（42.87）Cr_（15.98）Mo_（16.33）C_（15.94）B_（8.88）（at.%）was used to fabricate coatings by high-velocity oxygen fuel spraying.The effects of the spraying parameters on the microstructure and the wear properties of the Fe-based alloy coatings were systematically studied.The results showed that the obtained Fe-based coatings with a thickness of about 400μm consisted of a large-volume amorphous phase and some nanocrystals.With increasing the fuel and oxygen flow rates,the porosity of the obtained coatings decreased.The coating deposited under optimized parameters exhibited the lowest porosity of 2.8%.The excellent wear resistance of this coating was attributed to the properties of the amorphous matrix and the presence of nanocrystals homogeneously distributed within the matrix.The wear mechanism of the coatings was discussed on the basis of observations of the worn surfaces.