The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-...The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-2.5 MPa. The experimental result reveals that the characteristic of two body abrasive wear and oxidation wear mechanisms are present for SiCn/2618 Al composite under higher load and sliding speed. SiC ceramic continuous network as the reinforcement can avoid composite from the third body wear that usually occurs in traditional particle reinforced composite. The mechanically mixed layer (MML) controls greatly the wear rate and friction coefficient of the composites. The composites tested at higher sliding speed exhibit higher value of friction coefficient and fluctuation, which is associated with the intermittent formation and removal of the MML. The wear and stress—strain behaviors of SiCn/Fe–40Cr against SiCn/Al 2168 at 30-105 m/s under 1.0-2.5 MPa were analyzed by finite element method with the software Solidwork2012 Simulation, respectively. The wear and stress–strain behavior of the composite predicted by the FEM correlated well with the experimental results.展开更多
The hot deformation behavior of Ti-3.0Al-3.7Cr-2.0Fe-0.1B (TACFB) titanium alloy was investigated using a Gleeble-1500D thermal simulator in the temperature range of 800-950 °C, at constant strain rate from 0.01 ...The hot deformation behavior of Ti-3.0Al-3.7Cr-2.0Fe-0.1B (TACFB) titanium alloy was investigated using a Gleeble-1500D thermal simulator in the temperature range of 800-950 °C, at constant strain rate from 0.01 s-1 to 10 s-1 and with height reduction of 70%. Flow stress and microstructure evolution during hot compression of TACFB alloy were investigated. The processing map of TACFB alloy was obtained. The results indicate that the hot deformation behavior of TACFB alloy is sensitive to the deformation temperature and strain rate. The peak flow stress decreases with increasing the test temperature and decreasing the strain rate. The constitutive relationship of TACFB alloy was obtained on the base of Arrhenius equations. When the strain rates are higher than 1.0 s-1, the dynamic recrystallization occurs, and the higher the strain rates are, the more the recrystallization is.展开更多
A novel process for manufacturing A1-0.70Fe-0.24Cu alloy conductor was proposed, which includes horizontal continuous casting and subsequent continuous extrusion forming （Conform）. The mechanical properties, electri...A novel process for manufacturing A1-0.70Fe-0.24Cu alloy conductor was proposed, which includes horizontal continuous casting and subsequent continuous extrusion forming （Conform）. The mechanical properties, electrical conductivity and the compressed creep behaviour of the alloy were studied. The results indicate that the Conform process induces obvious grain refinement, strain-induced precipitation of AI7CuzFe phase and the transformation of crystal orientation distribution. The processed alloy has good comprehensive mechanical properties and electrical conductivity. Moreover, a better creep resistance under the conditions of 90 ~C and 76 MPa is shown compared with pure A1 and annealed copper, and the relationship between primary creep strain and time may comply with the logarithmic law. The enhanced properties are attributed to the grain refinement as well as the fine and homogeneously distributed thermally stable A1Fe and A17Cu2Fe precipitation phases.展开更多
The micro-laminated （ZrO2-Y2O3）/（Al2O3-Y2O3） composite films were prepared on the surface of Fe-13Cr alloy by an electrochemical process and a sintering process alternately. High-resolution field emission scanning...The micro-laminated （ZrO2-Y2O3）/（Al2O3-Y2O3） composite films were prepared on the surface of Fe-13Cr alloy by an electrochemical process and a sintering process alternately. High-resolution field emission scanning electron microscopy （FE-SEM） was used to characterize the laminated films, indicating that the micro-laminated （ZrO2-Y2O3）] （Al2O3-Y2O3） films have nano-structures. SEM, EDS and mass gain measurement were adopted to study the oxidation resistance of films on Fe-13Cr alloy. It is proved that such micro-laminated films are more effective than ZrO2-Y2O3 or Al2O3-Y2O3 films to resist the oxidation of the alloy, and the oxidation resistance is increased with increasing layers in micro-laminated films. These beneficial effects can be contributed to the mechanism, by which such micro-laminated （ZrOE- YEO3）/（Al2O3-Y2O3） composite film combines all the beneficial effects and overcomes all the disadvantages of both ZrOE- Y2O3 film and Al2O3-Y2O3 film during oxidation of alloy.展开更多
Experimental scratch tests and first-principles calculations were used to investigate the adhesion property of AlCrNbSiTi high-entropy alloy(HEA)coatings on zirconium substrates.AlCrNbSiTi HEA and Cr coatings were dep...Experimental scratch tests and first-principles calculations were used to investigate the adhesion property of AlCrNbSiTi high-entropy alloy(HEA)coatings on zirconium substrates.AlCrNbSiTi HEA and Cr coatings were deposited on Zr alloy substrates using multi-arc ion plating technology,and scratch tests were subsequently conducted to estimate the adhesion property of the coatings.The results indicated that Cr coatings had better adhesion strength than HEA coatings,and the HEA coatings showed brittleness.The special quasi-random structure approach was used to build HEA models,and Cr/Zr and HEA/Zr interface models were employed to investigate the cohesion between the coatings and Zr substrate using first-principles calculations.The calculated interface energies showed that the cohesion between the Cr coating and the Zr substrate was stronger than that of the HEA coating with Zr.In contrary to Al or Si in the HEA coating,Cr,Nb,and Ti atoms binded strongly with Zr substrate.Based on the calculated elastic constants,it was found that low Cr and high Al content decreased the mechanical performances of HEA coatings.Finally,this study demonstrated the utilization of a combined approach involving first-principles calculations and experimental studies for future HEA coating development.展开更多
The damage characteristics of different speed sections of Cu−Cr−Zr alloy rail after simulated launch were studied.The microstructure,morphologies and properties of samples were investigated by using XRD,XPS,EBSD,SEM,h...The damage characteristics of different speed sections of Cu−Cr−Zr alloy rail after simulated launch were studied.The microstructure,morphologies and properties of samples were investigated by using XRD,XPS,EBSD,SEM,hardness test,electrochemical test and DSC techniques.It was found that deposition layers were formed on the surfaces of the simulated launch samples.The thickness and surface roughness of these deposition layers increased with increasing the heat effect,suggesting a launch speed dependent damage degree of the arc ablation.The hardness variation of samples is attributed to the effects of the deposition layer and deformation hardening.The surface deposition layer affects corrosion resistance and crystalline characteristics,leading to changes in subsequent service performances.Additionally,the surface texture and plastic deformation ability of the samples are related to the recrystallization degree and deformation grain amount.展开更多
A novel process of electroplating amorphous Fe Cr Ni alloy in chloride aqueous solution with Fe(Ⅱ), Ni(Ⅱ) and Cr(Ⅲ) was reported. Couple plasma atomic emission spectrometry (ICP AES), X ray diffractometry(XRD), sca...A novel process of electroplating amorphous Fe Cr Ni alloy in chloride aqueous solution with Fe(Ⅱ), Ni(Ⅱ) and Cr(Ⅲ) was reported. Couple plasma atomic emission spectrometry (ICP AES), X ray diffractometry(XRD), scanning electronic microscopy(SEM), microhardness test and rapid heating cooling method were adopted to detect the properties of the amorphous Fe Ni Cr deposit, such as composition, crystalline structure, micrograph, hardness, and adherence between deposit and substrate. The effects of the operating parameters on the electrodeposit of the amorphous Fe Ni Cr alloy were discussed in detail. The results show that a 8.7?μm thick mirror like amorphous Fe Ni Cr alloy deposit, with Vicker’s hardness of 530 and composition of 45%～55% Fe, 33%～37% Ni, 9%～23% Cr was obtained by electroplating for 20?min at room temperature(10～30?℃), cathode current 10～16?A/dm 2, pH=1.0～3.0. The XRD patterns show that there only appears a broad hump around 2 θ of 41?°～47?°for the amorphous Fe Ni Cr alloy deposit, while the SEM micrographs show that the deposit contains only a few fine cracks but no pinholes.展开更多
Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electr...Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electron microscopy analyses,it was found that the spot defects were caused by the residual oxide layer on the surface of the cold-rolled Fe-36%Ni alloy strip after hydrogen annealing.By properly increasing the grinding amount of the blank before cold rolling to remove the oxide layer,the spot defects on the surface of the cold-rolled strip were effectively eliminated,and the surface quality of the product was ensured.展开更多
The effects of aging temperature on shape memory effect, mechanical properties and microstruc-ture of Fe-14Mn-5Si-8Cr-4Ni-0.2C shape memory alloy have been studied. The results showed that the second phase particles r...The effects of aging temperature on shape memory effect, mechanical properties and microstruc-ture of Fe-14Mn-5Si-8Cr-4Ni-0.2C shape memory alloy have been studied. The results showed that the second phase particles rich in chromium, manganese and silicon precipitate during aging, and thereby increase the hardness and strength of the alloy. The shape recovery ratio can be remarkably improved by aging and a maximum value can be obtained at 1223 K, which is 68% higher than that of the specimen in solid solution state. When the aging temperature is below 1223 K, the amount of second phase particles increases as the aging temperature increases. The size of austenite grain increases with increasing aging temperature. When the temperature is over 1223 K, the second phase particles can not precipitate. The lack of second phase particles and the increase of grain size make the hardness and shape recovery ratio drastically decrease, when the temperature is over 1223 K.展开更多
A high temperature embrittlement occures in Fe-15Cr-4AI and Fe-20Cr-4Al alloys treated over 1000 C.It is caused mainly by 475℃ brittleness during cooling.When a secondary treatment at 500℃ was conducted,the 475℃ br...A high temperature embrittlement occures in Fe-15Cr-4AI and Fe-20Cr-4Al alloys treated over 1000 C.It is caused mainly by 475℃ brittleness during cooling.When a secondary treatment at 500℃ was conducted,the 475℃ brittleness developed very rapidly.After only 15 rain of the treating,little plasticity was remained for all samples pretreuted at the temper- atures over 1000℃ and cooled in water.However,no 475℃ brittleness was generated when pretreating temperature was below 1000℃,Addition of Yttrium can inhibit not only grain growth,but also 475℃ brittleness.For the alloys with 0.2—0.4 wt-%Y,after treating at 800—1300℃,the plasticity did not decrease and the properties of furnace cooled samples were not lower than those of water cooled samples.展开更多
The effects of prestrain and annealing temperature on phase transformation temperatures in Fel4Mn5Si8Cr4Ni shape memory alloy have been studied. The results showed that when the annealing temperature was 673 K, both t...The effects of prestrain and annealing temperature on phase transformation temperatures in Fel4Mn5Si8Cr4Ni shape memory alloy have been studied. The results showed that when the annealing temperature was 673 K, both the At and the Ms temperatures increased appreciably as the prestrain increased, the As temperature increased slightly with increasing prestrain; the resistivity difference at 303 K between the heating and cooling curve also increased with increasing prestrain, which agreed with the recovery strain. The shape memory effect in Fe-Mn-Si-Cr-Ni shape memory alloy is caused by the stress-induced γ→ε martensite transformation and its reverse transformation. When the prestrain was 10%, the Ms temperature decreased remarkably as the annealing temperature increased.展开更多
The corrosion behaviors of Fe-Cr alloy under three different pH values solutions with C1- and SO42- were investigated by localized electrochemical impedance spectroscopy （LEIS） measurements and the corrosion product...The corrosion behaviors of Fe-Cr alloy under three different pH values solutions with C1- and SO42- were investigated by localized electrochemical impedance spectroscopy （LEIS） measurements and the corrosion products were analyzed by laser Raman spectrometry. The results show that the high corrosion resistance of Fe-Cr Alloy is attributed to a passive film which is formed more easily when the alloy contains a large quantity of Cr element. However, its corrosion resistance varies in the solutions with different pH values, especially in the initial corrosion. The average impedance values in neutral and alkaline solution are much higher than that in acidic solution because the passive film is more likely to dissolve in the acidic condition. Moreover, the destructive effect of C1- and SO42 ions on the passive film is also demonstrated in corrosion process through the change of the impedance value with the steeping time.展开更多
A rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr (mass fraction in percent) alloywas prepared by melt spinning. As-quenched and as-annealed microstructures were studied by X-raydiffractometry (XRD), transmission electron mic...A rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr (mass fraction in percent) alloywas prepared by melt spinning. As-quenched and as-annealed microstructures were studied by X-raydiffractometry (XRD), transmission electron microscopy (TEM), high-resolution transmission electronmicroscopy (HREM) and energy dispersive spectrum (EDS) analysis. The microhardness of the alloy atdifferent annealing temperatures was measured. The results obtained indicate that the microhardnessof the rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr alloy does not vary with different annealingtemperatures. The as-quenched microstructure of the alloy includes two kinds of dispersed primaryphases: Al_3Ti and Al_(13)(Cr, Fe)_2. After annealing at 400 deg C for 10 h, the stable phaseAl_(13)Fe_4 appears in the microstructure.展开更多
The 1100 degreesC isothermal oxidation behavior of Fe-23Cr-5Al alloy modified by yttrium addition was studied by means of thermogravimetric analysis, scanning electron microscopy and energy dispersive X-ray analysis. ...The 1100 degreesC isothermal oxidation behavior of Fe-23Cr-5Al alloy modified by yttrium addition was studied by means of thermogravimetric analysis, scanning electron microscopy and energy dispersive X-ray analysis. Yttrium was added to this alloy in the forms of metallic addition, yttrium oxide and ion implant. Cracking and spalling occurred on the convoluted scale formed on Y-free alloy and exposed the substrate. A flat dense scale without spallation was formed on the yttrium alloying addition or yttrium oxide dispersion alloy. The scale adhesion was also improved by 1x10(17)Y(+)/cm(2)-implantation. The results indicate the convoluted morphology of the scale on Fe-23Cr-5Al-0.21Ti alloy is related to the growth mechanism of the alumina scale, and the spallation of the scale is related to sulfur segregation at the scale/alloy interface. The main reason that the adhesion of alumina scale is improved by yttrium addition lies in the following. Yttrium is liable to form a stable yttrium sulfide with sulfur in the alloy and prevent sulfur interface from segregation. Another reason is that the growth mechanism of alumina scale is changed by yttrium addition.展开更多
基金Project (2012BAE06B01) supported by the Key Technology R&D Program During the 12th Five-Year Plan Period, ChinaProjects(21201030, 51272039, 51032007) supported by the National Natural Science Foundation of ChinaProject (1099043) supported by the Science and Technology in Guangxi Province, China
文摘The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-2.5 MPa. The experimental result reveals that the characteristic of two body abrasive wear and oxidation wear mechanisms are present for SiCn/2618 Al composite under higher load and sliding speed. SiC ceramic continuous network as the reinforcement can avoid composite from the third body wear that usually occurs in traditional particle reinforced composite. The mechanically mixed layer (MML) controls greatly the wear rate and friction coefficient of the composites. The composites tested at higher sliding speed exhibit higher value of friction coefficient and fluctuation, which is associated with the intermittent formation and removal of the MML. The wear and stress—strain behaviors of SiCn/Fe–40Cr against SiCn/Al 2168 at 30-105 m/s under 1.0-2.5 MPa were analyzed by finite element method with the software Solidwork2012 Simulation, respectively. The wear and stress–strain behavior of the composite predicted by the FEM correlated well with the experimental results.
基金Project (2010DFA52280) supported by International Science and Technology CooperationProject (20100470260) supported by China Postdoctoral Science Foundation
文摘The hot deformation behavior of Ti-3.0Al-3.7Cr-2.0Fe-0.1B (TACFB) titanium alloy was investigated using a Gleeble-1500D thermal simulator in the temperature range of 800-950 °C, at constant strain rate from 0.01 s-1 to 10 s-1 and with height reduction of 70%. Flow stress and microstructure evolution during hot compression of TACFB alloy were investigated. The processing map of TACFB alloy was obtained. The results indicate that the hot deformation behavior of TACFB alloy is sensitive to the deformation temperature and strain rate. The peak flow stress decreases with increasing the test temperature and decreasing the strain rate. The constitutive relationship of TACFB alloy was obtained on the base of Arrhenius equations. When the strain rates are higher than 1.0 s-1, the dynamic recrystallization occurs, and the higher the strain rates are, the more the recrystallization is.
基金Project(20130161110007) supported by the Doctoral Program of Higher Education of China
文摘A novel process for manufacturing A1-0.70Fe-0.24Cu alloy conductor was proposed, which includes horizontal continuous casting and subsequent continuous extrusion forming （Conform）. The mechanical properties, electrical conductivity and the compressed creep behaviour of the alloy were studied. The results indicate that the Conform process induces obvious grain refinement, strain-induced precipitation of AI7CuzFe phase and the transformation of crystal orientation distribution. The processed alloy has good comprehensive mechanical properties and electrical conductivity. Moreover, a better creep resistance under the conditions of 90 ~C and 76 MPa is shown compared with pure A1 and annealed copper, and the relationship between primary creep strain and time may comply with the logarithmic law. The enhanced properties are attributed to the grain refinement as well as the fine and homogeneously distributed thermally stable A1Fe and A17Cu2Fe precipitation phases.
文摘The micro-laminated （ZrO2-Y2O3）/（Al2O3-Y2O3） composite films were prepared on the surface of Fe-13Cr alloy by an electrochemical process and a sintering process alternately. High-resolution field emission scanning electron microscopy （FE-SEM） was used to characterize the laminated films, indicating that the micro-laminated （ZrO2-Y2O3）] （Al2O3-Y2O3） films have nano-structures. SEM, EDS and mass gain measurement were adopted to study the oxidation resistance of films on Fe-13Cr alloy. It is proved that such micro-laminated films are more effective than ZrO2-Y2O3 or Al2O3-Y2O3 films to resist the oxidation of the alloy, and the oxidation resistance is increased with increasing layers in micro-laminated films. These beneficial effects can be contributed to the mechanism, by which such micro-laminated （ZrOE- YEO3）/（Al2O3-Y2O3） composite film combines all the beneficial effects and overcomes all the disadvantages of both ZrOE- Y2O3 film and Al2O3-Y2O3 film during oxidation of alloy.
基金supported by Stability Supports Research Project of Treasury Department(No.197801)Talent Fund of CIAE(No.219213)。
文摘Experimental scratch tests and first-principles calculations were used to investigate the adhesion property of AlCrNbSiTi high-entropy alloy(HEA)coatings on zirconium substrates.AlCrNbSiTi HEA and Cr coatings were deposited on Zr alloy substrates using multi-arc ion plating technology,and scratch tests were subsequently conducted to estimate the adhesion property of the coatings.The results indicated that Cr coatings had better adhesion strength than HEA coatings,and the HEA coatings showed brittleness.The special quasi-random structure approach was used to build HEA models,and Cr/Zr and HEA/Zr interface models were employed to investigate the cohesion between the coatings and Zr substrate using first-principles calculations.The calculated interface energies showed that the cohesion between the Cr coating and the Zr substrate was stronger than that of the HEA coating with Zr.In contrary to Al or Si in the HEA coating,Cr,Nb,and Ti atoms binded strongly with Zr substrate.Based on the calculated elastic constants,it was found that low Cr and high Al content decreased the mechanical performances of HEA coatings.Finally,this study demonstrated the utilization of a combined approach involving first-principles calculations and experimental studies for future HEA coating development.
基金the Key Research and Development Program of China(No.2022YFB2404102)the National Natural Science Foundation of China(Nos.51971093,52171158,52101196)+5 种基金the Key Research and Development Program of Shandong Province,China(Nos.2020ZLYS11,2021ZLGX01,2022CXGC020308,2023CXGC010308)the Major Innovation Projects of Shandong Province,China(Nos.2020CXGC010701,2020CXGC010702)the Young Taishan Scholars,China(No.tsqn202211184)the Shandong Provincial Natural Science Foundation,China(No.ZR2022ME137)the Yantai Science and Technology Planning Project,China(No.2021ZDCX001)the Open Project Program of Shandong Marine Aerospace Equipment Technological Innovation Center(Ludong University),China(No.MAETIC2021-11).
文摘The damage characteristics of different speed sections of Cu−Cr−Zr alloy rail after simulated launch were studied.The microstructure,morphologies and properties of samples were investigated by using XRD,XPS,EBSD,SEM,hardness test,electrochemical test and DSC techniques.It was found that deposition layers were formed on the surfaces of the simulated launch samples.The thickness and surface roughness of these deposition layers increased with increasing the heat effect,suggesting a launch speed dependent damage degree of the arc ablation.The hardness variation of samples is attributed to the effects of the deposition layer and deformation hardening.The surface deposition layer affects corrosion resistance and crystalline characteristics,leading to changes in subsequent service performances.Additionally,the surface texture and plastic deformation ability of the samples are related to the recrystallization degree and deformation grain amount.
文摘A novel process of electroplating amorphous Fe Cr Ni alloy in chloride aqueous solution with Fe(Ⅱ), Ni(Ⅱ) and Cr(Ⅲ) was reported. Couple plasma atomic emission spectrometry (ICP AES), X ray diffractometry(XRD), scanning electronic microscopy(SEM), microhardness test and rapid heating cooling method were adopted to detect the properties of the amorphous Fe Ni Cr deposit, such as composition, crystalline structure, micrograph, hardness, and adherence between deposit and substrate. The effects of the operating parameters on the electrodeposit of the amorphous Fe Ni Cr alloy were discussed in detail. The results show that a 8.7?μm thick mirror like amorphous Fe Ni Cr alloy deposit, with Vicker’s hardness of 530 and composition of 45%～55% Fe, 33%～37% Ni, 9%～23% Cr was obtained by electroplating for 20?min at room temperature(10～30?℃), cathode current 10～16?A/dm 2, pH=1.0～3.0. The XRD patterns show that there only appears a broad hump around 2 θ of 41?°～47?°for the amorphous Fe Ni Cr alloy deposit, while the SEM micrographs show that the deposit contains only a few fine cracks but no pinholes.
文摘Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electron microscopy analyses,it was found that the spot defects were caused by the residual oxide layer on the surface of the cold-rolled Fe-36%Ni alloy strip after hydrogen annealing.By properly increasing the grinding amount of the blank before cold rolling to remove the oxide layer,the spot defects on the surface of the cold-rolled strip were effectively eliminated,and the surface quality of the product was ensured.
文摘The effects of aging temperature on shape memory effect, mechanical properties and microstruc-ture of Fe-14Mn-5Si-8Cr-4Ni-0.2C shape memory alloy have been studied. The results showed that the second phase particles rich in chromium, manganese and silicon precipitate during aging, and thereby increase the hardness and strength of the alloy. The shape recovery ratio can be remarkably improved by aging and a maximum value can be obtained at 1223 K, which is 68% higher than that of the specimen in solid solution state. When the aging temperature is below 1223 K, the amount of second phase particles increases as the aging temperature increases. The size of austenite grain increases with increasing aging temperature. When the temperature is over 1223 K, the second phase particles can not precipitate. The lack of second phase particles and the increase of grain size make the hardness and shape recovery ratio drastically decrease, when the temperature is over 1223 K.
文摘A high temperature embrittlement occures in Fe-15Cr-4AI and Fe-20Cr-4Al alloys treated over 1000 C.It is caused mainly by 475℃ brittleness during cooling.When a secondary treatment at 500℃ was conducted,the 475℃ brittleness developed very rapidly.After only 15 rain of the treating,little plasticity was remained for all samples pretreuted at the temper- atures over 1000℃ and cooled in water.However,no 475℃ brittleness was generated when pretreating temperature was below 1000℃,Addition of Yttrium can inhibit not only grain growth,but also 475℃ brittleness.For the alloys with 0.2—0.4 wt-%Y,after treating at 800—1300℃,the plasticity did not decrease and the properties of furnace cooled samples were not lower than those of water cooled samples.
文摘The effects of prestrain and annealing temperature on phase transformation temperatures in Fel4Mn5Si8Cr4Ni shape memory alloy have been studied. The results showed that when the annealing temperature was 673 K, both the At and the Ms temperatures increased appreciably as the prestrain increased, the As temperature increased slightly with increasing prestrain; the resistivity difference at 303 K between the heating and cooling curve also increased with increasing prestrain, which agreed with the recovery strain. The shape memory effect in Fe-Mn-Si-Cr-Ni shape memory alloy is caused by the stress-induced γ→ε martensite transformation and its reverse transformation. When the prestrain was 10%, the Ms temperature decreased remarkably as the annealing temperature increased.
基金National Natural Science Foundation of China (No. 50871021)
文摘The corrosion behaviors of Fe-Cr alloy under three different pH values solutions with C1- and SO42- were investigated by localized electrochemical impedance spectroscopy （LEIS） measurements and the corrosion products were analyzed by laser Raman spectrometry. The results show that the high corrosion resistance of Fe-Cr Alloy is attributed to a passive film which is formed more easily when the alloy contains a large quantity of Cr element. However, its corrosion resistance varies in the solutions with different pH values, especially in the initial corrosion. The average impedance values in neutral and alkaline solution are much higher than that in acidic solution because the passive film is more likely to dissolve in the acidic condition. Moreover, the destructive effect of C1- and SO42 ions on the passive film is also demonstrated in corrosion process through the change of the impedance value with the steeping time.
文摘A rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr (mass fraction in percent) alloywas prepared by melt spinning. As-quenched and as-annealed microstructures were studied by X-raydiffractometry (XRD), transmission electron microscopy (TEM), high-resolution transmission electronmicroscopy (HREM) and energy dispersive spectrum (EDS) analysis. The microhardness of the alloy atdifferent annealing temperatures was measured. The results obtained indicate that the microhardnessof the rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr alloy does not vary with different annealingtemperatures. The as-quenched microstructure of the alloy includes two kinds of dispersed primaryphases: Al_3Ti and Al_(13)(Cr, Fe)_2. After annealing at 400 deg C for 10 h, the stable phaseAl_(13)Fe_4 appears in the microstructure.
文摘The 1100 degreesC isothermal oxidation behavior of Fe-23Cr-5Al alloy modified by yttrium addition was studied by means of thermogravimetric analysis, scanning electron microscopy and energy dispersive X-ray analysis. Yttrium was added to this alloy in the forms of metallic addition, yttrium oxide and ion implant. Cracking and spalling occurred on the convoluted scale formed on Y-free alloy and exposed the substrate. A flat dense scale without spallation was formed on the yttrium alloying addition or yttrium oxide dispersion alloy. The scale adhesion was also improved by 1x10(17)Y(+)/cm(2)-implantation. The results indicate the convoluted morphology of the scale on Fe-23Cr-5Al-0.21Ti alloy is related to the growth mechanism of the alumina scale, and the spallation of the scale is related to sulfur segregation at the scale/alloy interface. The main reason that the adhesion of alumina scale is improved by yttrium addition lies in the following. Yttrium is liable to form a stable yttrium sulfide with sulfur in the alloy and prevent sulfur interface from segregation. Another reason is that the growth mechanism of alumina scale is changed by yttrium addition.
