Bulk metallic glass（BMG） rods Fe71Mo5-xNbxP12C10B2（x=1,2,3,4 and 5） with diameter of 1 or 2 mm were synthesized by copper mold casting.The effects of Nb substitution for Mo on the structure,thermal and mechanical ...Bulk metallic glass（BMG） rods Fe71Mo5-xNbxP12C10B2（x=1,2,3,4 and 5） with diameter of 1 or 2 mm were synthesized by copper mold casting.The effects of Nb substitution for Mo on the structure,thermal and mechanical properties of Fe71Mo5-xNbxP12C10B2 alloys were studied by X-ray diffraction,differential scanning calorimetry and compressive testing.The results show that the substitution of Nb for Mo leads to a decreased glass forming ability,but with plasticity of 1.0%,the fracture strength of Fe71Mo2Nb3P12C10B2 alloy increases up to 4.0 GPa.The improvement of the fracture strength is discussed in terms of the enhancement of atomic bonding nature and the favorite formation of a network-like structure due to the substitution of Nb for Mo.展开更多
In order to investigate the effect of the vacuum degree in vacuum induction melting （VIM） furnace on the mechanical properties of Ni-Fe-Cr based alloy, four samples were prepared under different conditions. The chem...In order to investigate the effect of the vacuum degree in vacuum induction melting （VIM） furnace on the mechanical properties of Ni-Fe-Cr based alloy, four samples were prepared under different conditions. The chemical analysis results show that under the argon atmosphere, there is more dissipation in Al and Ti, whereas it is reduced by establishing the vacuum atmosphere. The gas analysis results show that the oxygen and nitrogen contents of the samples decrease with increasing vacuum degree. However, there is no dissipation in the gas content of the samples in higher degree of vacuum. In addition, the thermodynamic calculations show that the probability of TiO2 and Al2O3 formation is high due to the small value of the equilibrium oxygen. Higher vacuum degree reduces the tensile and yield strength of the alloys, while it enhances the elongation and reduction of area values due to the lower amount of the inclusions and evaporation of Al and Ti under higher vacuum. On the other hand, increasing vacuum degree changes the fracture mode from brittle to ductile.展开更多
A FeCrSiBMn amorphous/nanocrystalline coating with 700 μm in thickness and 0.65% in porosity, was prepared by high velocity oxygen fuel(HVOF) spraying process. The long-term corrosion behavior of the FeCrSiBMn coatin...A FeCrSiBMn amorphous/nanocrystalline coating with 700 μm in thickness and 0.65% in porosity, was prepared by high velocity oxygen fuel(HVOF) spraying process. The long-term corrosion behavior of the FeCrSiBMn coating was evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy(EIS) tests in a 3.5% NaCl solution with a hard chromium coating as a reference. The FeCrSiBMn coating exhibited higher corrosion potential and lower corrosion current density than the hard chromium coating. The pore resistance(Rp) and charge transfer resistance(Rct) of FeCrSiBMn coating were higher than those of the hard chromium coating. In addition, after immersion in the Na Cl solution for 28 d, only small pores in the FeCrSiBMn coating were observed. All the results indicated that the FeCrSiBMn coating held superior corrosion resistance to the hard chromium coating. This could be attributed to the dense structure, low porosity and amorphous/nanocrystalline phases of the FeCrSiBMn coating.展开更多
Ti-Fe-x TiC(x=0, 3, 6, 9, wt.%) composites were fabricated through low temperature ball milling of Ti, Fe and TiC powders, followed by spark plasma sintering. The results show that β-Ti, β-Ti-Fe, η-Ti4 Fe2 O0.4 and...Ti-Fe-x TiC(x=0, 3, 6, 9, wt.%) composites were fabricated through low temperature ball milling of Ti, Fe and TiC powders, followed by spark plasma sintering. The results show that β-Ti, β-Ti-Fe, η-Ti4 Fe2 O0.4 and TiC particles can be found in the composites. The microstructure can be obviously refined with increasing the content of TiC particles. The coefficient of friction(COF) decreases and the hardness increases with increasing the content of TiC particles. The adhesive wear is the dominant wear mechanism of all the Ti-Fe-x TiC composites. The Ti-Fe-6 TiC composite shows the best wear resistance, owing to the small size and high content of TiC particle as well as relatively fine microstructure. The wear rate of the Ti-Fe-6 TiC composite is as low as 1.869× 10-5 mm3/(N·m) and the COF is only 0.64. Therefore, TiC particle reinforced Ti-Fe based composites may be utilized as potential wear resistant materials.展开更多
The widespread utilization of fossil fuels has caused an associated increase in CO_(2) emissions over the past few decades,which has resulted in global warming and ocean acidification.CO hydrogenation(Fischer‐Tropsch...The widespread utilization of fossil fuels has caused an associated increase in CO_(2) emissions over the past few decades,which has resulted in global warming and ocean acidification.CO hydrogenation(Fischer‐Tropsch synthesis,FTS)is considered a significant route for the production of liquid fuels and chemicals from nonpetroleum sources to meet worldwide demand.Conversion of CO_(2) with renewable H_(2) into valuable hydrocarbons is beneficial for reducing dependence on fossil fuels and mitigating the negative effects of high CO_(2) concentrations in the atmosphere.Iron‐based catalysts exhibit superior catalytic performance in both FTS and CO_(2) hydrogenation to value‐added hydrocarbons.The abundance and low cost of iron‐based catalysts also promote their wide application in CO_(x) hydrogenation.This paper provides a comprehensive overview of the significant developments in the application of iron‐based catalysts in these two fields.The active phases,promoter effect,and support of iron‐based catalysts are discussed in the present paper.Based on understanding of these three essential aspects,we also cover recent advances in the design and preparation of novel iron‐based catalysts for FTS and CO_(2) hydrogenation.Current challenges and future catalytic applications are also outlined.展开更多
The as-spun Ti_(1−x)La_(x)Fe_(0.8)Mn_(0.2)(x=0,0.01,0.03,0.06,0.09,molar fraction)alloys were prepared by melt spinning.The effects of La substitution for Ti on the microstructure,hydrogen storage kinetics and thermod...The as-spun Ti_(1−x)La_(x)Fe_(0.8)Mn_(0.2)(x=0,0.01,0.03,0.06,0.09,molar fraction)alloys were prepared by melt spinning.The effects of La substitution for Ti on the microstructure,hydrogen storage kinetics and thermodynamics of TiFe-type Ti−Fe−Mn-based alloy were investigated.The as-spun alloys hold the TiFe single phase,which transforms to TiFeH_(0.06),TiFeH,and TiFeH_(2) hydrides after hydrogenation.La substitution promotes the formation of micro-defects(such as dislocations and grain boundaries)in the alloys,thus facilitating hydrogen diffusion.In addition,the hydrogen storage kinetics properties are improved after introducing La element.With the rise of La content,the hydrogen storage capacity decreases firstly and then increases,but the absolute value of hydriding enthalpy change(|ΔH|)increases firstly and then reduces.When x=0.01,the maximum value of|ΔH|is obtained to be(25.23±0.50)kJ/mol for hydriding,and the alloy has the maximum hydrogen absorption capacity of(1.80±0.04)wt.%under the conditions of 323 K and 3 MPa.展开更多
Two isomers ofnitrochlorobenzene （o- andp-NCB） were treated by a Pd/Fe catalyst in aqueous solutions through catalytic amination and dechlorination. Nitrochlorobenzenes are rapidly converted to form chloroanilines ...Two isomers ofnitrochlorobenzene （o- andp-NCB） were treated by a Pd/Fe catalyst in aqueous solutions through catalytic amination and dechlorination. Nitrochlorobenzenes are rapidly converted to form chloroanilines （CAN） first through an amination process, and then rapidly dechlorinated to become aniline （AN） and CI^-, without the involvement of any other intermediate reaction products. The amination and dechlorination reaction are believed to take place predominantly on the surface site of the Pd/Fe catalysts. The dechlorination rate of the reductive degradation of the two isomers of nitrochlorobenzene （o-, and p-NCB） in the presence of Pd/Fe as a catalyst was measured experimentally. In all cases, the reaction rate constants were found to increase with the decrease in the Gibbs free energy （correlation with the activation energy） of NCBs formation; the activation energy of each dechlorination reaction was measured to be 95.83 and 77.05 kJ/mol, respectively for o- and p-NCB. The results demonstrated that p-NCBs were reduced more easily than o-NCBs.展开更多
The glass formation was intensively studied for Fe-based alloys. Parameters defining kinetics and thermodynamic behavior of crystallization were calculated using calorimetric measurements and physical properties of co...The glass formation was intensively studied for Fe-based alloys. Parameters defining kinetics and thermodynamic behavior of crystallization were calculated using calorimetric measurements and physical properties of constituent elements. It is found that the critical cooling rate Rc estimated by combining kinetic and thermodynamic parameters highly correlates with measured Rc found in literatures with correlation coefficient R2=0.944, and alloy compositions with high melting enthalpy AHm can easily form glass even without high undercooling and high value of the ,β-parameter of Tumbull＇s theory, revealing that the glass formation in this group of alloys is mostly controlled by growth limitation. This combination of kinetic and thermodynamic parameters can be used to determine alloy composition with good glass forming ability in Fe-based alloys just using physical properties of alloying elements and calorimetric measurements.展开更多
Asphaltene-ceramic composite membranes were fabricated from ceramic supports and an asphaltene component, which was obtained from the separation of coal to give a kind of new carbonaceous precursor material. Using SEM...Asphaltene-ceramic composite membranes were fabricated from ceramic supports and an asphaltene component, which was obtained from the separation of coal to give a kind of new carbonaceous precursor material. Using SEM and thermogravimetric analysis to measure the microstructure and properties of the asphaltene component allowed the porosity, permeability, and retention ratios to be determined. The results show that the asphaltene component can be regarded as a good carbon membrane precursor material because of its high carbon content and strong bonding capacity. When ceramic supports are impregnated with asphaltene colloid the asphaltene easily combines with the support surface and forms a good carbonaceous film after carbonization. Little of the asphaltene component permeates into the internal pores of the ceramic support. Although the number of coats applied to the substrate had little affect on the porosity of the asphaltene-ceramic composite membranes the permeability varied depend- ing upon the number of times the substrate was treated. The way bubbles escape from the film, and the phenomenon of coalescence, as affected by different film thicknesses also seem closely related to the number of coats. A composite membrane carbonized at a final temperature of 600℃ is relatively dense and the permeability of Fe（OH）3 colloid through it is very low. A membrane fired at 800℃ is porous and its permeability and retention of Fe（OH）3 colloid are 88 L/（m2 h MPa） and 85.3%, respectively when the trans-membrane pressure is 0.22 MPa.展开更多
Three electrodeposited Fe-Ni,Fe-Co,and Fe-Ni-Co cores of thin film transformer are prepared on silicon(100) substrates,which are sputtered a 90 nm thick film of Cu acting as the seed layer.The core films consisting of...Three electrodeposited Fe-Ni,Fe-Co,and Fe-Ni-Co cores of thin film transformer are prepared on silicon(100) substrates,which are sputtered a 90 nm thick film of Cu acting as the seed layer.The core films consisting of Fe-Ni 20:80,Fe-Co 60:40 and Fe-Ni-Co 10:60:30,respectively,are deposited using direct current electrodeposition.The surface texture,electrical and magnetic properties are surveyed by scanning electron microscopy(SEM),superconducting quantum interference device(SQUID),etc.The wave transmission ability and efficiency of thin film transformer with these cores,inputting the sine wave,are compared.All the analyses indicate that FeNi alloy films display the optimal magnetic properties and excellent transformer performance.展开更多
Temperature has great influence on the stacking fault energy (SFE). Both SFE and dγ 0/dT for Fe-based alloys containing substitutional or interstitial atoms increase with increasing temperature. Based on the thermody...Temperature has great influence on the stacking fault energy (SFE). Both SFE and dγ 0/dT for Fe-based alloys containing substitutional or interstitial atoms increase with increasing temperature. Based on the thermodynamic model of SFE, the equation $\frac{{d\gamma _0 }}{{dT}} = \frac{{d\gamma ^{ch} }}{{dT}} + \frac{{d\gamma ^{se\user1{g}} }}{{dT}} + \frac{{d\gamma ^{MG} }}{{dT}}$ and those expressions for three items involved are established. The calculatedγ 0/dT is generally consistent with the experimental. The influence of chemical free energy on the temperature dependence of SFE is almost constant, and is obviously stronger than that of magnetic and segregation contributions. The magnetic transition and the segregation of alloying elements at stacking faults cause a decrease in SFE of the alloys when temperature increases; that is, dγ MG/dT<0 and dγ seg/dT<0. Meanwhile, such an influence decreases with increasing temperature, except for the dγ seg/dT} of Fe?Mn?Si alloys. With these results, the experimental phenomena that the SFE of Fe-based alloys is not zero at the thermo-dynamically equilibrated temperature (T 0) of the λ and ε phases and they are positive both atT>T 0 andT<T 0 can be reasonably explained.展开更多
It was well known that it was very difficult to prepare high performance Fe-based bulk amorphous alloys with both high Fe content and good glass-forming ability, especially for the Fe content （or total magnetic eleme...It was well known that it was very difficult to prepare high performance Fe-based bulk amorphous alloys with both high Fe content and good glass-forming ability, especially for the Fe content （or total magnetic elements content） higher than 80 at%. In this paper, a series of Fe81-xCoxMO1P7.5C5.5B2Si3 （x = 0, 5, 10, 15, 20） bulk amorphous alloys （BAAs） with high saturation magnetization have been developed by copper mold casting method with fluxed ingot. It has been found that using Co replacing Fe in the Fe-Mo-P-C-B-Si alloy could significantly enhance the glass-forming ability and magnetic property. For the BAA with Co content of 0 at%, 5 at%, 10 at%, 15 at% and 20 at%, its saturation magnetization Js（Js=μoMs） was 1.55, 1.60, 1.62, 1.65 and 1.59 T, respectively. Among these alloys, the Fe66Co15- Mo1P7.5C5.5B2Si3 BAA exhibited a critical size of 2 mm in diameter and a high Js of 1.65 T. It suggested that these alloys with high magnetic element content possessed great potential in application due to their high glass-forming ability and high magnetic property.展开更多
基金Project (SWU110046) supported by the Doctorate Foundation of Southwest University,China
文摘Bulk metallic glass（BMG） rods Fe71Mo5-xNbxP12C10B2（x=1,2,3,4 and 5） with diameter of 1 or 2 mm were synthesized by copper mold casting.The effects of Nb substitution for Mo on the structure,thermal and mechanical properties of Fe71Mo5-xNbxP12C10B2 alloys were studied by X-ray diffraction,differential scanning calorimetry and compressive testing.The results show that the substitution of Nb for Mo leads to a decreased glass forming ability,but with plasticity of 1.0%,the fracture strength of Fe71Mo2Nb3P12C10B2 alloy increases up to 4.0 GPa.The improvement of the fracture strength is discussed in terms of the enhancement of atomic bonding nature and the favorite formation of a network-like structure due to the substitution of Nb for Mo.
文摘In order to investigate the effect of the vacuum degree in vacuum induction melting （VIM） furnace on the mechanical properties of Ni-Fe-Cr based alloy, four samples were prepared under different conditions. The chemical analysis results show that under the argon atmosphere, there is more dissipation in Al and Ti, whereas it is reduced by establishing the vacuum atmosphere. The gas analysis results show that the oxygen and nitrogen contents of the samples decrease with increasing vacuum degree. However, there is no dissipation in the gas content of the samples in higher degree of vacuum. In addition, the thermodynamic calculations show that the probability of TiO2 and Al2O3 formation is high due to the small value of the equilibrium oxygen. Higher vacuum degree reduces the tensile and yield strength of the alloys, while it enhances the elongation and reduction of area values due to the lower amount of the inclusions and evaporation of Al and Ti under higher vacuum. On the other hand, increasing vacuum degree changes the fracture mode from brittle to ductile.
文摘A FeCrSiBMn amorphous/nanocrystalline coating with 700 μm in thickness and 0.65% in porosity, was prepared by high velocity oxygen fuel(HVOF) spraying process. The long-term corrosion behavior of the FeCrSiBMn coating was evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy(EIS) tests in a 3.5% NaCl solution with a hard chromium coating as a reference. The FeCrSiBMn coating exhibited higher corrosion potential and lower corrosion current density than the hard chromium coating. The pore resistance(Rp) and charge transfer resistance(Rct) of FeCrSiBMn coating were higher than those of the hard chromium coating. In addition, after immersion in the Na Cl solution for 28 d, only small pores in the FeCrSiBMn coating were observed. All the results indicated that the FeCrSiBMn coating held superior corrosion resistance to the hard chromium coating. This could be attributed to the dense structure, low porosity and amorphous/nanocrystalline phases of the FeCrSiBMn coating.
基金financial support from the National Key Fundamental Research and Development Project of China (2014CB644002)。
文摘Ti-Fe-x TiC(x=0, 3, 6, 9, wt.%) composites were fabricated through low temperature ball milling of Ti, Fe and TiC powders, followed by spark plasma sintering. The results show that β-Ti, β-Ti-Fe, η-Ti4 Fe2 O0.4 and TiC particles can be found in the composites. The microstructure can be obviously refined with increasing the content of TiC particles. The coefficient of friction(COF) decreases and the hardness increases with increasing the content of TiC particles. The adhesive wear is the dominant wear mechanism of all the Ti-Fe-x TiC composites. The Ti-Fe-6 TiC composite shows the best wear resistance, owing to the small size and high content of TiC particle as well as relatively fine microstructure. The wear rate of the Ti-Fe-6 TiC composite is as low as 1.869× 10-5 mm3/(N·m) and the COF is only 0.64. Therefore, TiC particle reinforced Ti-Fe based composites may be utilized as potential wear resistant materials.
文摘The widespread utilization of fossil fuels has caused an associated increase in CO_(2) emissions over the past few decades,which has resulted in global warming and ocean acidification.CO hydrogenation(Fischer‐Tropsch synthesis,FTS)is considered a significant route for the production of liquid fuels and chemicals from nonpetroleum sources to meet worldwide demand.Conversion of CO_(2) with renewable H_(2) into valuable hydrocarbons is beneficial for reducing dependence on fossil fuels and mitigating the negative effects of high CO_(2) concentrations in the atmosphere.Iron‐based catalysts exhibit superior catalytic performance in both FTS and CO_(2) hydrogenation to value‐added hydrocarbons.The abundance and low cost of iron‐based catalysts also promote their wide application in CO_(x) hydrogenation.This paper provides a comprehensive overview of the significant developments in the application of iron‐based catalysts in these two fields.The active phases,promoter effect,and support of iron‐based catalysts are discussed in the present paper.Based on understanding of these three essential aspects,we also cover recent advances in the design and preparation of novel iron‐based catalysts for FTS and CO_(2) hydrogenation.Current challenges and future catalytic applications are also outlined.
基金financial supports from the Inner Mongolia Natural Science Foundation,China (No.2019BS05005)the Inner Mongolia University of Science and Technology Innovation Fund,China (No.2019QDL-B11)the National Natural Science Foundation of China (Nos.51901105, 51871125, 51761032).
文摘The as-spun Ti_(1−x)La_(x)Fe_(0.8)Mn_(0.2)(x=0,0.01,0.03,0.06,0.09,molar fraction)alloys were prepared by melt spinning.The effects of La substitution for Ti on the microstructure,hydrogen storage kinetics and thermodynamics of TiFe-type Ti−Fe−Mn-based alloy were investigated.The as-spun alloys hold the TiFe single phase,which transforms to TiFeH_(0.06),TiFeH,and TiFeH_(2) hydrides after hydrogenation.La substitution promotes the formation of micro-defects(such as dislocations and grain boundaries)in the alloys,thus facilitating hydrogen diffusion.In addition,the hydrogen storage kinetics properties are improved after introducing La element.With the rise of La content,the hydrogen storage capacity decreases firstly and then increases,but the absolute value of hydriding enthalpy change(|ΔH|)increases firstly and then reduces.When x=0.01,the maximum value of|ΔH|is obtained to be(25.23±0.50)kJ/mol for hydriding,and the alloy has the maximum hydrogen absorption capacity of(1.80±0.04)wt.%under the conditions of 323 K and 3 MPa.
基金Project (No. 20407015) supported by the National Natural ScienceFoundation of China
文摘Two isomers ofnitrochlorobenzene （o- andp-NCB） were treated by a Pd/Fe catalyst in aqueous solutions through catalytic amination and dechlorination. Nitrochlorobenzenes are rapidly converted to form chloroanilines （CAN） first through an amination process, and then rapidly dechlorinated to become aniline （AN） and CI^-, without the involvement of any other intermediate reaction products. The amination and dechlorination reaction are believed to take place predominantly on the surface site of the Pd/Fe catalysts. The dechlorination rate of the reductive degradation of the two isomers of nitrochlorobenzene （o-, and p-NCB） in the presence of Pd/Fe as a catalyst was measured experimentally. In all cases, the reaction rate constants were found to increase with the decrease in the Gibbs free energy （correlation with the activation energy） of NCBs formation; the activation energy of each dechlorination reaction was measured to be 95.83 and 77.05 kJ/mol, respectively for o- and p-NCB. The results demonstrated that p-NCBs were reduced more easily than o-NCBs.
基金Projects(51174094, 51101059) supported by the National Natural Science Foundation of China
文摘The glass formation was intensively studied for Fe-based alloys. Parameters defining kinetics and thermodynamic behavior of crystallization were calculated using calorimetric measurements and physical properties of constituent elements. It is found that the critical cooling rate Rc estimated by combining kinetic and thermodynamic parameters highly correlates with measured Rc found in literatures with correlation coefficient R2=0.944, and alloy compositions with high melting enthalpy AHm can easily form glass even without high undercooling and high value of the ,β-parameter of Tumbull＇s theory, revealing that the glass formation in this group of alloys is mostly controlled by growth limitation. This combination of kinetic and thermodynamic parameters can be used to determine alloy composition with good glass forming ability in Fe-based alloys just using physical properties of alloying elements and calorimetric measurements.
基金the National Natural Science Foundation of China (Nos.50874108 and 50921002)the Natural Science Foundation of Jiangsu Province (No.BK2007038)+2 种基金the Fundamental Research Funds for the Central Universities (No.2010LKHX01)the Open Fund of Key Laboratory of Coal ProcessClean Utilization of Ministry of Education (No.CPEUKF08-06)
文摘Asphaltene-ceramic composite membranes were fabricated from ceramic supports and an asphaltene component, which was obtained from the separation of coal to give a kind of new carbonaceous precursor material. Using SEM and thermogravimetric analysis to measure the microstructure and properties of the asphaltene component allowed the porosity, permeability, and retention ratios to be determined. The results show that the asphaltene component can be regarded as a good carbon membrane precursor material because of its high carbon content and strong bonding capacity. When ceramic supports are impregnated with asphaltene colloid the asphaltene easily combines with the support surface and forms a good carbonaceous film after carbonization. Little of the asphaltene component permeates into the internal pores of the ceramic support. Although the number of coats applied to the substrate had little affect on the porosity of the asphaltene-ceramic composite membranes the permeability varied depend- ing upon the number of times the substrate was treated. The way bubbles escape from the film, and the phenomenon of coalescence, as affected by different film thicknesses also seem closely related to the number of coats. A composite membrane carbonized at a final temperature of 600℃ is relatively dense and the permeability of Fe（OH）3 colloid through it is very low. A membrane fired at 800℃ is porous and its permeability and retention of Fe（OH）3 colloid are 88 L/（m2 h MPa） and 85.3%, respectively when the trans-membrane pressure is 0.22 MPa.
基金supported by the National Natural Science Foundation of China (Grant No. 60874101)
文摘Three electrodeposited Fe-Ni,Fe-Co,and Fe-Ni-Co cores of thin film transformer are prepared on silicon(100) substrates,which are sputtered a 90 nm thick film of Cu acting as the seed layer.The core films consisting of Fe-Ni 20:80,Fe-Co 60:40 and Fe-Ni-Co 10:60:30,respectively,are deposited using direct current electrodeposition.The surface texture,electrical and magnetic properties are surveyed by scanning electron microscopy(SEM),superconducting quantum interference device(SQUID),etc.The wave transmission ability and efficiency of thin film transformer with these cores,inputting the sine wave,are compared.All the analyses indicate that FeNi alloy films display the optimal magnetic properties and excellent transformer performance.
基金This work was supported by the National Natural Science Foundation of China (Grant No.59671023) the Fund for Ph. D. Program, the Ministry of Education (No. 97024835) of China and the Emerson Electric Co. USA.
文摘Temperature has great influence on the stacking fault energy (SFE). Both SFE and dγ 0/dT for Fe-based alloys containing substitutional or interstitial atoms increase with increasing temperature. Based on the thermodynamic model of SFE, the equation $\frac{{d\gamma _0 }}{{dT}} = \frac{{d\gamma ^{ch} }}{{dT}} + \frac{{d\gamma ^{se\user1{g}} }}{{dT}} + \frac{{d\gamma ^{MG} }}{{dT}}$ and those expressions for three items involved are established. The calculatedγ 0/dT is generally consistent with the experimental. The influence of chemical free energy on the temperature dependence of SFE is almost constant, and is obviously stronger than that of magnetic and segregation contributions. The magnetic transition and the segregation of alloying elements at stacking faults cause a decrease in SFE of the alloys when temperature increases; that is, dγ MG/dT<0 and dγ seg/dT<0. Meanwhile, such an influence decreases with increasing temperature, except for the dγ seg/dT} of Fe?Mn?Si alloys. With these results, the experimental phenomena that the SFE of Fe-based alloys is not zero at the thermo-dynamically equilibrated temperature (T 0) of the λ and ε phases and they are positive both atT>T 0 andT<T 0 can be reasonably explained.
基金supported by the National Natural Science Foundation of China (51271097)
文摘It was well known that it was very difficult to prepare high performance Fe-based bulk amorphous alloys with both high Fe content and good glass-forming ability, especially for the Fe content （or total magnetic elements content） higher than 80 at%. In this paper, a series of Fe81-xCoxMO1P7.5C5.5B2Si3 （x = 0, 5, 10, 15, 20） bulk amorphous alloys （BAAs） with high saturation magnetization have been developed by copper mold casting method with fluxed ingot. It has been found that using Co replacing Fe in the Fe-Mo-P-C-B-Si alloy could significantly enhance the glass-forming ability and magnetic property. For the BAA with Co content of 0 at%, 5 at%, 10 at%, 15 at% and 20 at%, its saturation magnetization Js（Js=μoMs） was 1.55, 1.60, 1.62, 1.65 and 1.59 T, respectively. Among these alloys, the Fe66Co15- Mo1P7.5C5.5B2Si3 BAA exhibited a critical size of 2 mm in diameter and a high Js of 1.65 T. It suggested that these alloys with high magnetic element content possessed great potential in application due to their high glass-forming ability and high magnetic property.
