Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electr...Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electron microscopy analyses,it was found that the spot defects were caused by the residual oxide layer on the surface of the cold-rolled Fe-36%Ni alloy strip after hydrogen annealing.By properly increasing the grinding amount of the blank before cold rolling to remove the oxide layer,the spot defects on the surface of the cold-rolled strip were effectively eliminated,and the surface quality of the product was ensured.展开更多
The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-...The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-2.5 MPa. The experimental result reveals that the characteristic of two body abrasive wear and oxidation wear mechanisms are present for SiCn/2618 Al composite under higher load and sliding speed. SiC ceramic continuous network as the reinforcement can avoid composite from the third body wear that usually occurs in traditional particle reinforced composite. The mechanically mixed layer (MML) controls greatly the wear rate and friction coefficient of the composites. The composites tested at higher sliding speed exhibit higher value of friction coefficient and fluctuation, which is associated with the intermittent formation and removal of the MML. The wear and stress—strain behaviors of SiCn/Fe–40Cr against SiCn/Al 2168 at 30-105 m/s under 1.0-2.5 MPa were analyzed by finite element method with the software Solidwork2012 Simulation, respectively. The wear and stress–strain behavior of the composite predicted by the FEM correlated well with the experimental results.展开更多
The Hot deformation and martensitic transformation behaviors of Fe-32%Ni alloy was investigated by measurements of electrical resistance and X-ray diffraction. With the increase in strain, the austenite goes through f...The Hot deformation and martensitic transformation behaviors of Fe-32%Ni alloy was investigated by measurements of electrical resistance and X-ray diffraction. With the increase in strain, the austenite goes through from the work-hardened to the partial dynamcally re-crystallized and then to the completed dynamically re-crystallized. The martensitic transformation characteristics depend on the austenite states. The work-hardening in small strain is helpful to martensitic transformation due to the low dislocation density and little lattice distortion, while the high dislocation density and severe lattice distortion by the increase in strain will hinder the martensitic nucleation. Once dynamic re-crystallization （ DRX ） takes place, the martensitic transformation will be enhanced again, which is related to the heterogeneous dynamic substructures. The growing DRX grain can enhance the martensitic nucleation due to the low dislocation density near its grain boundary.展开更多
文摘Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electron microscopy analyses,it was found that the spot defects were caused by the residual oxide layer on the surface of the cold-rolled Fe-36%Ni alloy strip after hydrogen annealing.By properly increasing the grinding amount of the blank before cold rolling to remove the oxide layer,the spot defects on the surface of the cold-rolled strip were effectively eliminated,and the surface quality of the product was ensured.
基金Project (2012BAE06B01) supported by the Key Technology R&D Program During the 12th Five-Year Plan Period, ChinaProjects(21201030, 51272039, 51032007) supported by the National Natural Science Foundation of ChinaProject (1099043) supported by the Science and Technology in Guangxi Province, China
文摘The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-2.5 MPa. The experimental result reveals that the characteristic of two body abrasive wear and oxidation wear mechanisms are present for SiCn/2618 Al composite under higher load and sliding speed. SiC ceramic continuous network as the reinforcement can avoid composite from the third body wear that usually occurs in traditional particle reinforced composite. The mechanically mixed layer (MML) controls greatly the wear rate and friction coefficient of the composites. The composites tested at higher sliding speed exhibit higher value of friction coefficient and fluctuation, which is associated with the intermittent formation and removal of the MML. The wear and stress—strain behaviors of SiCn/Fe–40Cr against SiCn/Al 2168 at 30-105 m/s under 1.0-2.5 MPa were analyzed by finite element method with the software Solidwork2012 Simulation, respectively. The wear and stress–strain behavior of the composite predicted by the FEM correlated well with the experimental results.
基金the National Natural Science Foundation of China （No. 50471017）.
文摘The Hot deformation and martensitic transformation behaviors of Fe-32%Ni alloy was investigated by measurements of electrical resistance and X-ray diffraction. With the increase in strain, the austenite goes through from the work-hardened to the partial dynamcally re-crystallized and then to the completed dynamically re-crystallized. The martensitic transformation characteristics depend on the austenite states. The work-hardening in small strain is helpful to martensitic transformation due to the low dislocation density and little lattice distortion, while the high dislocation density and severe lattice distortion by the increase in strain will hinder the martensitic nucleation. Once dynamic re-crystallization （ DRX ） takes place, the martensitic transformation will be enhanced again, which is related to the heterogeneous dynamic substructures. The growing DRX grain can enhance the martensitic nucleation due to the low dislocation density near its grain boundary.
