Thermal expansion behaviors of FeNi alloys were investigated by means of X-ray diffraction technique within a Fe1 -xNix/Cu superiattice structure. It was found that with a Ni concentration of x = 0.35, FeNi alloy laye...Thermal expansion behaviors of FeNi alloys were investigated by means of X-ray diffraction technique within a Fe1 -xNix/Cu superiattice structure. It was found that with a Ni concentration of x = 0.35, FeNi alloy layers showed the well-known Invar behavior, but for alloy layers with either lower or higher Ni concentrations, thermal expansion coefficients were larger. Based on results of magnetic measurements it is concluded that FeNi alloy layers with Ni concentrations lower than the Invar composition are in a superparamagnetic state which leads not only to low spontaneous magnetizations but also to large thermal expansions of the alloy layers.展开更多
Measurements of magnetic susceptibility in mechanically alloyed Fe-Ni Invar alloys were taken under pressures up to 7.5GPa. The rate of decrease in the Curie temperature for 700℃ annealed specimen was larger than tha...Measurements of magnetic susceptibility in mechanically alloyed Fe-Ni Invar alloys were taken under pressures up to 7.5GPa. The rate of decrease in the Curie temperature for 700℃ annealed specimen was larger than that annealed at 1000℃. This result can be explained by considering the fact that the width of the concentration fluctuation becomes larger in the specimen annealed at lower temperature.展开更多
Gas atomized 4J36 alloy powder was milled for 72 h then mixed with ZrW2O8 powder and sintered at 600℃ for 4 h under argon atmosphere. 4J36/ZrW2O8 composites containing 10 vol.%, 20 vol.%, 30 vol.%, and 40 vol.% ZrW2O...Gas atomized 4J36 alloy powder was milled for 72 h then mixed with ZrW2O8 powder and sintered at 600℃ for 4 h under argon atmosphere. 4J36/ZrW2O8 composites containing 10 vol.%, 20 vol.%, 30 vol.%, and 40 vol.% ZrW2Os were fabricated, the relative density of which ranged from 70% to 80%. Thermal expansion coefficients of the composites decreased as the amount of ZrW2O8 increased, in agreement with the rule of the mixture. The coefficient of thermal expansion of the 4J36/40 vol.%ZrW2O8 composite in 25-100℃ is 0.55 × 10^＋6/℃.展开更多
Theoretical investigation of the phase equilibria of the Fe-Ni alloy has been performed by combining the FLAPW total energy calculations and the Cluster Variation Method through the Cluster Expansion Method. The calcu...Theoretical investigation of the phase equilibria of the Fe-Ni alloy has been performed by combining the FLAPW total energy calculations and the Cluster Variation Method through the Cluster Expansion Method. The calculations have proved the stabilization of the LIE phase at 1：3 stoichiometry, which is in agreement with the experimental result, and predicted the existence of L1 0 as a stable phase below 550 K; this L1 0 phase has been missing in the conventional phase diagram. The calculations are extended to the Fe-rich region that is characterized by a wide range phase separation and has drawn considerable attention because of the intriguing Invar property associated with a Fe concentration of 65%. To reveal the origin of the phase separation, a P-V curve in an entire concentration range is derived by the second derivative of free energy functional of the disordered phase with respect to the volume. The calculation confirmed that the phase separation is caused by the breakdown of the mechanical-stability criterion. The newly calculated phase separation line combined with the L1 0 and L12Eorder-disordered phase boundaries provides phase equilibria in the wider concentration range of the system. Furthermore, a coefficient of thermal expansion （CTE） is attempted by incorporating the thermal vibration effect through harmonic approximation of the Debye-Gruneisen model. The Invar behavior has been reproduced, and the origin of this anomalous volume change has been discussed.展开更多
In this work,the Invar 36 alloys were manufactured using cold spray(CS)additive manufacturing technique.The systematic investigations were made on the microstructural evolution,thermal expansion and mechanical propert...In this work,the Invar 36 alloys were manufactured using cold spray(CS)additive manufacturing technique.The systematic investigations were made on the microstructural evolution,thermal expansion and mechanical properties under as-sprayed(AS)and heat-treated(HT)conditions.XRD(X-ray diffraction)and ICP-AES(inductively coupled plasma atomic emission spectroscopy)analyses show that no phase transformation,oxidation,nor element content change have occurred.The X-ray computed tomography(XCT)exhibited a near fully dense structure with a porosity of 0.025%in the helium-produced sample under as-sprayed condition,whereas the nitrogen-produced samples produced at 5 MPa and 800℃show more irregular pore defects.He-AS sample shows a more prominent grain refinement than that of nitrogen samples due to the more extensive plastic deformation.The post heat-treatment exhibited a promoted grain growth,inter-particle diffusion,as well as the formation of annealing twins.Between25℃and 200℃,the nitrogen samples possessed lower CTE(coefficient of thermal expansion)values(1.53×10^(-6)/℃)compared with those produced by casting and laser additive manufacturing.The He-AS samples exhibited a noticeable negative CTE value between 25℃and 200℃,which may due to the significant compressive residual stress(-272 MPa)compensating its displacement with temperature increase during CTE test.The N2-HT and He-HT Invar 36 samples present a notable balance between strength and ductility.In conclusion,the CS technique can be considered as a potential method to produce the Invar36 component with high thermal and mechanical performance.展开更多
文摘Thermal expansion behaviors of FeNi alloys were investigated by means of X-ray diffraction technique within a Fe1 -xNix/Cu superiattice structure. It was found that with a Ni concentration of x = 0.35, FeNi alloy layers showed the well-known Invar behavior, but for alloy layers with either lower or higher Ni concentrations, thermal expansion coefficients were larger. Based on results of magnetic measurements it is concluded that FeNi alloy layers with Ni concentrations lower than the Invar composition are in a superparamagnetic state which leads not only to low spontaneous magnetizations but also to large thermal expansions of the alloy layers.
文摘Measurements of magnetic susceptibility in mechanically alloyed Fe-Ni Invar alloys were taken under pressures up to 7.5GPa. The rate of decrease in the Curie temperature for 700℃ annealed specimen was larger than that annealed at 1000℃. This result can be explained by considering the fact that the width of the concentration fluctuation becomes larger in the specimen annealed at lower temperature.
基金supported by the Research Academies and Institutes Funds of the Ministry of Science and Technology of China (Ke-05021050)
文摘Gas atomized 4J36 alloy powder was milled for 72 h then mixed with ZrW2O8 powder and sintered at 600℃ for 4 h under argon atmosphere. 4J36/ZrW2O8 composites containing 10 vol.%, 20 vol.%, 30 vol.%, and 40 vol.% ZrW2Os were fabricated, the relative density of which ranged from 70% to 80%. Thermal expansion coefficients of the composites decreased as the amount of ZrW2O8 increased, in agreement with the rule of the mixture. The coefficient of thermal expansion of the 4J36/40 vol.%ZrW2O8 composite in 25-100℃ is 0.55 × 10^＋6/℃.
文摘Theoretical investigation of the phase equilibria of the Fe-Ni alloy has been performed by combining the FLAPW total energy calculations and the Cluster Variation Method through the Cluster Expansion Method. The calculations have proved the stabilization of the LIE phase at 1：3 stoichiometry, which is in agreement with the experimental result, and predicted the existence of L1 0 as a stable phase below 550 K; this L1 0 phase has been missing in the conventional phase diagram. The calculations are extended to the Fe-rich region that is characterized by a wide range phase separation and has drawn considerable attention because of the intriguing Invar property associated with a Fe concentration of 65%. To reveal the origin of the phase separation, a P-V curve in an entire concentration range is derived by the second derivative of free energy functional of the disordered phase with respect to the volume. The calculation confirmed that the phase separation is caused by the breakdown of the mechanical-stability criterion. The newly calculated phase separation line combined with the L1 0 and L12Eorder-disordered phase boundaries provides phase equilibria in the wider concentration range of the system. Furthermore, a coefficient of thermal expansion （CTE） is attempted by incorporating the thermal vibration effect through harmonic approximation of the Debye-Gruneisen model. The Invar behavior has been reproduced, and the origin of this anomalous volume change has been discussed.
基金supported financially by the National Key Research and Development Program of China(No.2019YFA0705300)the Guangdong Special Support Program(No.2019BT02C629)+6 种基金the National Natural Science Foundation of China(No.51690160)the Shanghai Science and Technology Committee(No.19DZ1100704)the Shanghai Sailing Program(No.19YF1415900)Golden Apple Project of Baosteel Co.,Ltd(No.A19EC13500)the Guangdong Basic and Applied Basic Research Foundation(No.2019B1515120016)the Guangzhou Science and Technology Program(Nos.202002030290 and 202007020008)the GDAS’Project of Science and Technology Development(Nos.2019GDASYL-0503006 and 2020GDASYL-20200302011)。
文摘In this work,the Invar 36 alloys were manufactured using cold spray(CS)additive manufacturing technique.The systematic investigations were made on the microstructural evolution,thermal expansion and mechanical properties under as-sprayed(AS)and heat-treated(HT)conditions.XRD(X-ray diffraction)and ICP-AES(inductively coupled plasma atomic emission spectroscopy)analyses show that no phase transformation,oxidation,nor element content change have occurred.The X-ray computed tomography(XCT)exhibited a near fully dense structure with a porosity of 0.025%in the helium-produced sample under as-sprayed condition,whereas the nitrogen-produced samples produced at 5 MPa and 800℃show more irregular pore defects.He-AS sample shows a more prominent grain refinement than that of nitrogen samples due to the more extensive plastic deformation.The post heat-treatment exhibited a promoted grain growth,inter-particle diffusion,as well as the formation of annealing twins.Between25℃and 200℃,the nitrogen samples possessed lower CTE(coefficient of thermal expansion)values(1.53×10^(-6)/℃)compared with those produced by casting and laser additive manufacturing.The He-AS samples exhibited a noticeable negative CTE value between 25℃and 200℃,which may due to the significant compressive residual stress(-272 MPa)compensating its displacement with temperature increase during CTE test.The N2-HT and He-HT Invar 36 samples present a notable balance between strength and ductility.In conclusion,the CS technique can be considered as a potential method to produce the Invar36 component with high thermal and mechanical performance.
