EFFECT OF Cr,Cu AND Co ON MAGNETOSTRICTION OF Fe-Si-B AMORPHOUS ALLOYS

The dependence of composition varied,especially C,Si,Cr,Cu and Co in four amorphous alloy systems Fe_(80-x)Cr_xSi_5B_(15).Fe_(80-x)Cr_xC_5B_(15).Fe_(80-x)Cu_xSi_5B_(15)and (Fe_(1-x)Co_x)_(82)Cu_(0.4)Si_(4.4)B_(13.2)upon their saturation magnetostriction at room temperature has been studied.It was observed that the saturation magnetostriction of the alloys may be re- markably improved by small addition of Cu and Co.the peak value being up to 70×10^(-6)as x=0.02 in alloys(Fe_(1-x)Co_x)_(82)Cu_(0.4)Si_(4.4)B_(13.2).

INFLECTION OF COERCIVITY DURING LOCAL CRYSTALLIZATION OF Fe-Si-B AMORPHOUS ALLOYS

An inflection hehaviour was revealed during isothermal annealing under the observation of transition of the coercivity of Fe-Si-B amorphous alloys during local crystallization.It may be interpreted by the transition of α-Fe grain precipitated from single to multiple domain, Thus,the theoretical expression of H_0-t_a may be derived.The plot of expression H_0-t_a calcu- lated well represents the feature of the experimental curve.

Progress and prospects of Mg-based amorphous alloys in azo dye wastewater treatment

Mg-based amorphous alloys exhibit efficient catalytic performance and excellent biocompatibility with a promising application probability,specifically in the field of azo dye wastewater degradation.However,the problems like difficulty in preparation and poor cycling stability need to be solved.At present,Mg-based amorphous alloys applied in wastewater degradation are available in powder and ribbon.The amorphous alloy powder fabricated by ball milling has a high specific surface area,and its reactivity is thousands of times better than that of gas atomized alloy powder.But the development is limited due to the high energy consumption,difficult and costly process of powder recycling.The single roller melt-spinning method is a new manufacturing process of amorphous alloy ribbon.Compared to amorphous powder,the specific surface area of amorphous ribbon is relatively lower,therefore,it is necessary to carry out surface modification to enhance it.Dealloying is a way that can form a pore structure on the surface of the amorphous alloys,increasing the specific surface area and providing more reactive sites,which all contribute to the catalytic performance.Exploring the optimal conditions for Mg-based amorphous alloys in wastewater degradation by adjusting amorphous alloy composition,choosing suitable method to preparation and surface modification,reducing cost,expanding the pH range will advance the steps to put Mg-based amorphous alloys in industrial environments into practice.

Research of caged dynamics of clusters center atoms in Pd_(82)Si_(18) amorphous alloy

To date,there is still a lack of a comprehensive explanation for caged dynamics which is regarded as one of the intricate dynamic behaviors in amorphous alloys.This study focuses on Pd_(82)Si_(18)as the research object to further elucidate the underlying mechanism of caged dynamics from multiple perspectives,including the cage's lifetime,atomic local environment,and atomic potential energy.The results reveal that Si atoms exhibit a pronounced cage effect due to the hindrance of Pd atoms,resulting in an anomalous peak in the non-Gaussian parameters.An in-depth investigation was conducted on the caged dynamics differences between fast and slow Si atoms.In comparison to fast Si atoms,slow Si atoms were surrounded by more Pd atoms and occupied lower potential energy states,resulting in smaller diffusion displacements for the slow Si atoms.Concurrently,slow Si atoms tend to be in the centers of smaller clusters with coordination numbers of 9 and 10.During the isothermal relaxation process,clusters with coordination numbers 9 and 10 have longer lifetimes,suggesting that the escape of slow Si atoms from their cages is more challenging.The findings mentioned above hold significant implications for understanding the caged dynamics.

Dealloying of an amorphous TiCuRu alloy results in a nanostructured electrocatalyst for hydrogen evolution reaction

Development of an electrocatalyst that is cheap and has good properties to replace conventional noble metals is important for H_(2) applications.In this study,dealloying of an amorphous Ti_(37)Cu_(60)Ru_(3) alloy was performed to prepare a freestanding nanostructured hydrogen evolution reaction(HER)catalyst.The effect of dealloying and addition of Ru to TiCu alloys on the microstructure and HER properties under alkaline conditions was investigated.3 at.%Ru addition in Ti_(40)Cu_(60) decreases the overpotential to reach a current density of 10mA cm^(-2) and Tafel slope of the dealloyed samples to 35 and 34mV dec−1.The improvement of electrocatalytic properties was attributed to the formation of a nanostructure and the modification of the electronic structure of the catalyst.First-principles calculations based on density function theory indicate that Ru decreases the Gibbs free energy of water dissociation.This work presents a method to prepare an efficient electrocatalyst via dealloying of amorphous alloys.

Clean production of Fe-based amorphous soft magnetic alloys via smelting reduction of high-phosphorus iron ore and apatite

Separated preparation of prealloys and amorphous alloys results in severe solidification-remelting and beneficial element removal-readdition contradictions,which markedly increase energy consumption and emissions.This study offered a novel strategy for the direct production of FePC amorphous soft magnetic alloys via smelting reduction of high-phosphorus iron ore(HPIO)and apatite.First,the thermodynamic conditions and equilibrium states of the carbothermal reduction reactions in HPIO were calculated,and the element content in reduced alloys was theoretically determined.The phase and structural evolutions,as well as element migration and enrichment behaviors during the smelting reduction of HPIO and Ca_(3)(PO_(4))_(2),were then experimentally verified.The addition of Ca_(3)(PO_(4))_(2)in HPIO contributes to the enrichment of the P element in reduced alloys and the subsequent development of Fe_(3)P and Fe_(2)P phases.The content of P and C elements in the range of 1.52 wt% -14.63 wt% and 0.62 wt% -2.47 wt%,respectively,can be well tailored by adding 0-50 g Ca_(3)(PO_(4))_(2)and controlling the C/O mole ratio of 0.8-1.1,which is highly consistent with the calculated results.These FePC alloys were then successfully formed into amorphous ribbons and rods.The energy consumption of the proposed strategy was estimated to be 2.00×10^(8) kJ/t,which is reduced by 30% when compared with the conventional production process.These results are critical for the comprehensive utilization of mineral resources and pave the way for the clean production of Fe-based amorphous soft magnetic alloys.

Influence of Metalloid Elements on the Magnetic Properties and Anisotropy of FeNi-based Amorphous Alloys

The magnetic properties and anisotropy of amor- phous(Fe_(80)Ni_(20))_(78)Si_xB_(22-x).alloys have been investigated systematically.The maximum permeability,coercive force and remanence have been determined for as-prepared and annealed samples,The results on the technical magnetic properties of this alloy system have been discussed and compared with Masumoto's.

EFFECT OF COMPOSITION ON PHYSICAL PROPERTIES OF AMORPHOUS Fe-Si-B ALLOYS

ＥＦＦＥＣＴＯＦＣＯＭＰＯＳＩＴＩＯＮＯＮＰＨＹＳＩＣＡＬＰＲＯＰＥＲＴＩＥＳＯＦＡＭＯＲＰＨＯＵＳＦｅＳｉＢＡＬＬＯＹＳ①ＷａｎｇＬｉｎｇｌｉｎｇ，ＺｈａｏＬｉｈｕａ，ＨｕＷａｎｇｙｕ，ＷｕＬｉｊｕｎ，ＺｈａｎｇＢａｎｇｗｅｉＤｅｐａｒｔｍｅ...

Curie Temperature of Amorphous Fe-Si-B and Fe-W-Si-B Alloys

オhe effects of composition, annealing temperature and time, annealing heating rate on the Curie temperature of amorphous FeSiB and FeWSiB alloys were studied. The results indicate that the Curie temperature of these alloys increases with the increase of the metalloid content when it is <25 at%, then decreases with the further increase of the metalloid content. For amorphous FeSiB and FeWSiB alloys with the low metalloid content, the Curie temperature increases with the annealing temperature and the annealing time. However, for the amorphous FeWSiB alloys with the high metalloid content, the Curie temperature increases at low annealing temperature and with short annealing time, and decreases at high annealing temperature and with long annealing time. The heating rate in measuring Curie temperature also influences the Curie temperature of the alloys. The Curie temperature is higher at lower heating rates.

BEHAVIORS OF THE HYPERFINE. FIELD AND THE ATOMIC MAGNETIC MOMENT IN AMORPHOUS Fe_(80-x)T_xB_(20)(T=Co,Ni,Mn,V,Ti) ALLOYS

The mean hyper fine field at the Fe nuclei in amorphous alloys Fe80-xTxB20(T=Co,Ni,Mn,V,Ti) by fitting the Moessbauer spectra is displayed. The behaviors of both the hyperfine field and the atomic magnetic moment in these amorphous alloys and the relation between both the properties are discussed.

STUDY ON THE SHOCK WAVE CRYSTALLIZATION OF AMORPHOUS ALLOYS BY DSC

Shock wave and annealing crystallization of amorphous alloys FeSiB, FeMoSiB and FeCuNbSiB were studied by isothermal and non-isothermal DSC technique. It was found that the shock wave crystallization is very perfect, the fraction crystallized is very close to 100%, though the period of crystallization is very short, only about 10-4-10-6s. Their produced phases differ from the parent phase in structure and composition. The high velocity of the transformation is very difficult to explain by the diffusion theory of solid state phase transition.

Properties of electrodeposited amorphous Fe-Ni-W alloy deposits

A new technique of electroplating amorphous Fe-Ni-W alloy deposits was proposed.The structure and morphology o Fe-Ni-W alloy deposit were detected by XRD and SEM.The friction and wear behavior of Fe-Ni-W alloy deposit were studied and compared with that of chromium deposit.The corrosion properties against 5% sodium chloride,5% sulfuric acid and 5% sodium hydroxide were also discussed.The experimental results indicate that Fe-Ni-W alloy deposits have superior properties against wea than hard chromium deposits under dry sliding condition.Under oil sliding condition,except their better wear resistance,the deposits can protect their counterparts against wear.The deposits plated on brass and AISI 1045 steel show good behavior against corrosion o 5% sodium chloride,5% sulfuric acid and 5% sodium hydroxide.The bath of electroplating amorphous Fe-Ni-W alloy deposits is environmentally friendly and would find widely use in industry.

Effect of Lanthanum on Performance of RuB Amorphous Alloy Catalyst for Benzene Selective Hydrogenation

The effect of La on the performance of a supported RuB amorphous alloy catalyst for benzene selective hydrogenation was studied by means of activity and selectivity tests, such as HRTEM, SAED, XPS, and XRD. The results show that the addition of La to RuB amorphous alloy catalyst can evidently increase the activity and improve the thermal stability of RuB amorphous alloy to refrain its crystallization. The promoting effect of La on the activity of RuB amorphous alloy catalyst is because of the high dispersion of the active components.

Corrosion behavior of Mg-Zn-Ca amorphous alloys with Nd addition in simulated body fluids

The effects of Nd addition on corrosion behavior of Mg66Zn30Ca4 amorphous alloys in simulated body f luids(SBF) were studied in this paper. Electrochemical properties of the samples before and after corrosion were determined. Surface morphologies of samples after immersion in SBF at 37℃ for different times were observed under scanning electron microscope(SEM). Results show that the corrosion resistance of Mg-based alloys in SBF is improved with the addition of Nd element. The electrochemical properties indicate that microalloying Nd element to the alloys leads to an ennoblement in the open circuit potentials of the alloys and a decrease in the anodic current density in SBF, especially for the Mg66-xZn30Ca4 Ndx alloys with Nd content of 1.0at.%-1.5at.%. It was observed that the surface morphologies of the alloys immersed in SBF change with the Nd addition. A f lakelike structure parallel to the alloy substrate formed on the surface of 1.0at.% Nd-containing alloy immersed in SBF for 7 days improves the corrosion resistance of the amorphous alloys by blocking the corrosion liquid from attacking the alloys.

Amorphous phase formation rules in high-entropy alloys

There have been many interesting studies on high-entropy alloys（HEAs）, also known as multi-component（MC） alloys（MCAs）, in recent years. MC metallic-glasses（MGs） have shown the potential to express the advantages of MCAs and MGs in tandem. Amorphous phase formation rules are a crucial issue in the HEA and MCA field. For equal or near-equal atomic ratio alloys, mixed-entropy among the elements has a significant effect on the phase formation. This paper focuses on HEA amorphous phase formation rules. In the first two sections, the recent progress in amorphous phase formation in HEAs and MCAs is reviewed, including the effective factors and correlative parameters related to amorphous phase formation. In the third section, novel MCMGs including high-entropy（HE） bulk-metallic-glass（HE-BMG） and MCMG films developed in recent decades are summarized, and the giant-magnetic-impedance（GMI） effect of MC amorphous fibers is discussed.

Soft magnetic properties of amorphous Fe_(52)Co_(34)Hf_7B_6Cu_1 alloy treated by pulsed magnetic field and annealing

The crystallization, microstructure, and soft magnetic properties of Fe52Co34Hf7B6Cul alloy are studied. Amorphous Fe52Co34Hf7B6Cul alloys are first treated by a pulsed magnetic field with a medium frequency, and then annealed at 100 ℃-400 ℃ for 30 min in a vacuum. The rise in temperature during the treatment by a pulsed magnetic field is measured by a non-contact infrared thermometer. The soft magnetic properties of specimens are measured by a vibrating sample magnetometer （VSM）. The microstructure changes of specimens are observed by a MSssbauer spectroscopy and transmission electron microscope （TEM）. The results show the medium-frequency pulsating magnetic field will pro- mote nanocrystallization of the amorphous alloy with a lower temperature rise. The nanocrystalline phase is （α-Fe（Co） with bcc crystal structure, and the grain size is about 10 nm. After vacuum annealing at 100 ℃ for 30 min, scattering nanocrystalline phases become more uniform, the coercive force and the saturation magnetization of the specimens are 41.98 A/m and 185.15 emu/g.

Microstructure of Cu-based Amorphous Composite Coatings on AZ91D Magnesium Alloy by Laser Cladding

To improve the sliding wear resistance of AZ91D magnesium alloy, Cu-based amorphous composite coatings made of CuaTTi34Zr11Nis and Cu47Ti34Zr11Ni8＋20 wt pct SiC powders were fabricated on AZ91D magnesium alloy by laser cladding, respectively. SEM （scanning electron microscopy）, EDS （energy dispersive X-ray spectroscopy）, XRD （X-ray diffraction） and TEM （transmission electron microscopy） techniques were employed to study the phases of the coatings. The results show that the coatings mainly consist of amorphous phase and different intermetallic compounds. The reason of formation of amorphous phase and the function of SiC particles were explained in details.

Effect of Cerium on Chemical Short Range Order of Al-Fe-Ce Amorphous Alloy

The chemical short-range order of Al-Fe-Ce amorphous alloy was studied by means of X-ray diffraction (XRD) and differential scanning calorimetry (DSC). It is found that the prepeak position in X-ray diffraction intensity curve shifts to higher angles as the content of Fe increases, but it shifts to smaller angles as the content of Ce increases. The crystallization character of the amorphous alloy changes with the variation of the content of Fe and Ce. Ce can improve the interaction between atoms and the capacity of compound formation, so it is favorable to Al-based glass formability.

Effect of yttrium on thermal stability and crystallization behavior of Nd_(60)Fe_(20)Al_(10)Ni_(10) amorphous alloys

The effect of yttrium on the thermal stability and crystallization behavior of Nd-Fe-Al-Ni amorphous alloys was investigated using X-ray diffraction （XRD）, differential scanning calorimeter （DSC）, and transmission electron microscopy （TEM）.The results indicated that the as-cast Nd60Fe20Al10Ni10-xYx（X=-0, 2） amorphous alloys were fabricated with some quenched-in crystals, which could be restrained by Y. With the effect of yttrium, both the crystallization temperature and exothermic peak shifted to higher temperatures, illustrating that the thermal stability could be improved. The addition of Y changed the crystallization process and final crystallization results. Moreover, the crystallites in the amorphous matrix became more homogeneous and smaller. Meanwhile, Y was useful for the passivation of oxygen in chemistry and restrained the negative effect of oxygen. The activation energies of the start of crystallization and peaking were 1.21 and 1.16 eV, respectively, according to the Kissinger equation.