The study of lithographic variation in resistive random access memory

Reducing the process variation is a significant concern for resistive random access memory(RRAM).Due to its ultrahigh integration density,RRAM arrays are prone to lithographic variation during the lithography process,introducing electrical variation among different RRAM devices.In this work,an optical physical verification methodology for the RRAM array is developed,and the effects of different layout parameters on important electrical characteristics are systematically investigated.The results indicate that the RRAM devices can be categorized into three clusters according to their locations and lithography environments.The read resistance is more sensitive to the locations in the array(~30%)than SET/RESET voltage(<10%).The increase in the RRAM device length and the application of the optical proximity correction technique can help to reduce the variation to less than 10%,whereas it reduces RRAM read resistance by 4×,resulting in a higher power and area consumption.As such,we provide design guidelines to minimize the electrical variation of RRAM arrays due to the lithography process.

Recovery of single event upset in advanced complementary metal-oxide semiconductor static random access memory cells

Using computer-aided design three-dimensional （3D） simulation technology, the recovery mechanism of single event upset and the effects of spacing and hit angle on the recovery are studied. It is found that the multi-node charge collection plays a key role in recovery and shielding the charge sharing by adding guard rings. It cannot exhibit the recovery effect. It is also indicated that the upset linear energy transfer （LET） threshold is kept constant while the recovery LET threshold increases as the spacing increases. Additionally, the effect of incident angle on recovery is analysed and it is shown that a larger angle can bring about a stronger charge sharing effect, thus strengthening the recovery ability.

Si1Sb2Te3 phase change material for chalcogenide random access memory

This paper investigated phase change Si1Sb2Te3 material for application of chalcogenide random access memory. Current-voltage performance was conducted to determine threshold current of phase change from amorphous phase to polycrystalline phase. The film holds a threshold current about 0.155 mA, which is smaller than the value 0.31 mA of Ge2Sb2Te5 film. Amorphous Si1Sb2Te3 changes to face-centred-cubic structure at ~ 180℃ and changes to hexagonal structure at ~ 270℃. Annealing temperature dependent electric resistivity of Si1Sb2Te3 film was studied by four-point probe method. Data retention of the films was characterized as well.

Three-Dimensional Simulations of RESET Operation in Phase-Change Random Access Memory with Blade-Type Like Phase Change Layer by Finite Element Modeling

An optimized device structure for reducing the RESET current of phase-change random access memory （PCRAM） with blade-type like （BTL） phase change layer is proposed. The electrical thermal analysis of the BTL cell and the blade heater contactor structure by three-dimensional finite element modeling are compared with each other during RESET operation. The simulation results show that the programming region of the phase change layer in the BTL cell is much smaller, and thermal electrical distributions of the BTL cell are more concentrated on the TiN/GST interface. The results indicate that the BTL cell has the superiorities of increasing the heating efficiency, decreasing the power consumption and reducing the RESET current from 0.67mA to 0.32mA. Therefore, the BTL cell will be appropriate for high performance PCRAM device with lower power consumption and lower RESET current.

Perpendicular magnetic tunnel junction and its application in magnetic random access memory

Recent progresses in magnetic tunnel junctions with perpendicular magnetic anisotropy （PMA） are reviewed and summarized. At first, the concept and source of perpendicular magnetic anisotropy （PMA） are introduced. Next, a historical overview of PMA materials as magnetic electrodes, such as the RE-TM alloys TbFeCo and GdFeCo, novel tetragonal manganese alloys Mn-Ga, L10-ordered （Co, Fe）/Pt alloy, multilayer film [Co, Fe, CoFe/Pt, Pd, Ni, AU]N, and ultra-thin magnetic metal/oxidized barrier is offered. The other part of the article focuses on the optimization and fabrication of CoFeB/MgO/CoFeB p-MTJs, which is thought to have high potential to meet the main demands for non-volatile magnetic random access memory.

Universal memory based on phase-change materials:From phase-change random access memory to optoelectronic hybrid storage

The era of information explosion is coming and information need to be continuously stored and randomly accessed over long-term periods,which constitute an insurmountable challenge for existing data centers.At present,computing devices use the von Neumann architecture with separate computing and memory units,which exposes the shortcomings of“memory bottleneck”.Nonvolatile memristor can realize data storage and in-memory computing at the same time and promises to overcome this bottleneck.Phase-change random access memory(PCRAM)is called one of the best solutions for next generation non-volatile memory.Due to its high speed,good data retention,high density,low power consumption,PCRAM has the broad commercial prospects in the in-memory computing application.In this review,the research progress of phase-change materials and device structures for PCRAM,as well as the most critical performances for a universal memory,such as speed,capacity,and power consumption,are reviewed.By comparing the advantages and disadvantages of phase-change optical disk and PCRAM,a new concept of optoelectronic hybrid storage based on phase-change material is proposed.Furthermore,its feasibility to replace existing memory technologies as a universal memory is also discussed as well.

Total ionizing radiation-induced read bit-errors in toggle magnetoresistive random-access memory devices

The 1-Mb and 4-Mb commercial toggle magnetoresistive random-access memories（MRAMs） with 0.13 μm and 0.18-μm complementary metal–oxide–semiconductor（CMOS） process respectively and different magnetic tunneling junctions（MTJs） are irradiated with a Cobalt-60 gamma source. The electrical functions of devices during the irradiation and the room temperature annealing behavior are measured. Electrical failures are observed until the dose accumulates to 120-krad（Si） in 4-Mb MRAM while the 1-Mb MRAM keeps normal. Thus, the 0.13-μm process circuit exhibits better radiation tolerance than the 0.18-μm process circuit. However, a small quantity of read bit-errors randomly occurs only in 1-Mb MRAM during the irradiation while their electrical function is normal. It indicates that the store states of MTJ may be influenced by gamma radiation, although the electrical transport and magnetic properties are inherently immune to the radiation. We propose that the magnetic Compton scattering in the interaction of gamma ray with magnetic free layer may be the origin of the read bit-errors. Our results are useful for MRAM toward space application.

Resistive switching characteristic and uniformity of low-power HfO_x-based resistive random access memory with the BN insertion layer

In this letter,the Ta/HfO/BN/TiN resistive switching devices are fabricated and they exhibit low power consumption and high uniformity each.The reset current is reduced for the HfO/BN bilayer device compared with that for the Ta/HfO/TiN structure.Furthermore,the reset current decreases with increasing BN thickness.The HfOlayer is a dominating switching layer,while the low-permittivity and high-resistivity BN layer acts as a barrier of electrons injection into TiN electrode.The current conduction mechanism of low resistance state in the HfO/BN bilayer device is space-chargelimited current(SCLC),while it is Ohmic conduction in the HfOdevice.

Thermal stability and data retention of resistive random access memory with HfOx/ZnO double layers

As an industry accepted storage scheme, hafnium oxide（HfO_x） based resistive random access memory（RRAM）should further improve its thermal stability and data retention for practical applications. We therefore fabricated RRAMs with HfO_x/ZnO double-layer as the storage medium to study their thermal stability as well as data retention. The HfO_x/ZnO double-layer is capable of reversible bipolar switching under ultralow switching current（〈 3 μA） with a Schottky emission dominant conduction for the high resistance state and a Poole–Frenkel emission governed conduction for the low resistance state. Compared with a drastically increased switching current at 120℃ for the single HfO_x layer RRAM, the HfO_x/ZnO double-layer exhibits excellent thermal stability and maintains neglectful fluctuations in switching current at high temperatures（up to 180℃）, which might be attributed to the increased Schottky barrier height to suppress current at high temperatures. Additionally, the HfO_x/ZnO double-layer exhibits 10-year data retention @85℃ that is helpful for the practical applications in RRAMs.

Synergistic effects of total ionizing dose on single event upset sensitivity in static random access memory under proton irradiation

Synergistic effects of the total ionizing dose （TID） on the single event upset （SEU） sensitivity in static random access memories （SRAMs） were studied by using protons. The total dose was cumulated with high flux protons during the TID exposure, and the SEU cross section was tested with low flux protons at several cumulated dose steps. Because of the radiation-induced off-state leakage current increase of the CMOS transistors, the noise margin became asymmetric and the memory imprint effect was observed.

Pattern imprinting in deep sub-micron static random access memories induced by total dose irradiation

Pattem imprinting in deep sub-micron static random access memories （SRAMs） during total dose irradiation is inves- tigated in detail. As the dose accumulates, the data pattern of memory cells loading during irradiation is gradually imprinted on their background data pattern. We build a relationship between the memory cell＇s static noise margin （SNM） and the background data, and study the influence of irradiation on the probability density function of ASNM, which is the difference between two data sides＇ SNMs, to discuss the reason for pattern imprinting. Finally, we demonstrate that, for micron and deep sub-micron devices, the mechanism of pattern imprinting is the bias-dependent threshold shift of the transistor, but for a deep sub-micron device the shift results from charge trapping in the shallow trench isolation （STI） oxide rather than from the gate oxide of the micron-device.

Set Programming Method and Performance Improvement of Phase Change Random Access Memory Arrays

A novel slow-down set waveform is proposed to improve the set performance and a 1 kb phase change random access memory chip fabricated with a 13nm CMOS technology is implemented to investigate the set performance by different set programming strategies based on this new set pulse. The amplitude difference （I1 - I2） of the set pulse is proved to be a crucial parameter for set programming. We observe and analyze the cell characteristics with different I1 - I2 by means of thermal simulations and high-resolution transmission electron microscopy, which reveal that an incomplete set programming will occur when the proposed slow-down pulse is set with an improperly high I1 - I2. This will lead to an amorphous residue in the active region. We also discuss the programming method to avoid the set performance degradations.

Ionizing radiation effect on single event upset sensitivity of ferroelectric random access memory

The impact of ionizing radiation effect on single event upset（SEU） sensitivity of ferroelectric random access memory（FRAM） is studied in this work. The test specimens were firstly subjected to ^60Co γ-ray and then the SEU evaluation was conducted using ^209Bi ions. As a result of TID-induced fatigue-like and imprint-like phenomena of the ferroelectric material, the SEU cross sections of the post-irradiated devices shift substantially. Different trends of SEU cross section with elevated dose were also found, depending on whether the same or complementary test pattern was employed during the TID exposure and the SEU measurement.

Effect of Pulse and dc Formation on the Performance of One-Transistor and One-Resistor Resistance Random Access Memory Devices

We investigate the effect of the formation process under pulse and dc modes on the performance of one transistor and one resistor （1 T1R） resistance random access memory （RRAM） device. All the devices are operated under the same test conditions, except for the initial formation process with different modes. Based on the statistical results, the high resistance state （FIRS） under the dc forming mode shows a lower value with better distribution compared with that under the pulse mode. One of the possible reasons for such a phenomenon originates from different properties of conductive filament （CF） formed in the resistive switching layer under two different modes. For the dc forming mode, the formed filament is thought to be continuous, which is hard to be ruptured, resulting in a lower HRS. However, in the case of pulse forming, the filament is discontinuous where the transport mechanism is governed by hopping. The low resistance state （LRS） can be easily changed by removing a few trapping states from the conducting path. Hence, a higher FIRS is thus observed. However, the HRS resistance is highly dependent on the length of the gap opened. A slight variation of the gap length will cause wide dispersion of resistance.

Effects of Film Thickness and Ar/O2 Ratio on Resistive Switching Characteristics of HfOx-Based Resistive-Switching Random Access Memories

Cu/HfOx/n^＋Si devices are fabricated to investigate the influence of technological parameters including film thickness and Ar/02 ratio on the resistive switching （RS） characteristics of HfOx films, in terms of switch ratio, endurance properties, retention time and multilevel storage. It is revealed that the RS characteristics show strong dependence on technological parameters mainly by altering the defects （oxygen vacancies） in the film. The sample with thickness of 2Onto and Ar/O2 ratio of 12：3 exhibits the best RS behavior with the potential of multilevel storage. The conduction mechanism of all the films is interpreted based on the filamentary model.

Analysis and modeling of resistive switching mechanisms oriented to resistive random-access memory

With the progress of the semiconductor industry,the resistive random-access memory（RAM） has drawn increasing attention.The discovery of the memristor has brought much attention to this study.Research has focused on the resistive switching characteristics of different materials and the analysis of resistive switching mechanisms.We discuss the resistive switching mechanisms of different materials in this paper and analyze the differences of those mechanisms from the view point of circuitry to establish their respective circuit models.Finally,simulations are presented.We give the prospect of using different materials in resistive RAM on account of their resistive switching mechanisms,which are applied to explain their resistive switchings.

Graphene resistive random memory - the promising memory device in next generation

Graphene-based resistive random access memory （GRRAM） has grasped researchers＇ attention due to its merits com- pared with ordinary RRAM. In this paper, we briefly review different types of GRRAMs. These GRRAMs can be divided into two categories： graphene RRAM and graphene oxide （GO）/reduced graphene oxide （rGO） RRAM. Using graphene as the electrode, GRRAM can own many good characteristics, such as low power consumption, higher density, transparency, SET voltage modulation, high uniformity, and so on. Graphene flakes sandwiched between two dielectric layers can lower the SET voltage and achieve multilevel switching. Moreover, the GRRAM with rGO and GO as the dielectric or electrode can be simply fabricated. Flexible and high performance RRAM and GO film can be modified by adding other materials layer or making a composite with polymer, nanoparticle, and 2D materials to further improve the performance. Above all, GRRAM shows huge potential to become the next generation memory.

Advances of embedded resistive random access memory in industrial manufacturing and its potential applications

Embedded memory,which heavily relies on the manufacturing process,has been widely adopted in various industrial applications.As the field of embedded memory continues to evolve,innovative strategies are emerging to enhance performance.Among them,resistive random access memory(RRAM)has gained significant attention due to its numerousadvantages over traditional memory devices,including high speed(<1 ns),high density(4 F^(2)·n^(-1)),high scalability(~nm),and low power consumption(~pJ).This review focuses on the recent progress of embedded RRAM in industrial manufacturing and its potentialapplications.It provides a brief introduction to the concepts and advantages of RRAM,discusses the key factors that impact its industrial manufacturing,and presents the commercial progress driven by cutting-edge nanotechnology,which has been pursued by manysemiconductor giants.Additionally,it highlights the adoption of embedded RRAM in emerging applications within the realm of the Internet of Things and future intelligent computing,with a particular emphasis on its role in neuromorphic computing.Finally,the review discusses thecurrent challenges and provides insights into the prospects of embedded RRAM in the era of big data and artificial intelligence.

存储体编译和布局协同的片上缓存设计方法

为了提高片上缓存的速度、降低面积和功耗,提出了一种存储体编译和布局协同的片上缓存设计方法。该方法基于存储体在芯片上的不同空间位置预估该存储体的时序余量,分别采用拆分/合并、尺寸调整、阈值替换和长宽比变形等多种配置参数穷举组合进行存储体编译,根据时序余量选择最优的静态随机存取存储器存储体编译配置。将该方法与现有的物理设计步骤集成为一个完整的设计流程。实验结果表明,该方法能够降低约9.9%的功耗,同时缩短7.5%的关键路径延时。

NMOS晶体管电荷共享导致的SRAM单元单粒子翻转恢复效应研究

基于Synopsys公司的三维器件模拟软件TCAD,本文研究了NMOS晶体管电荷共享导致SRAM单元的单粒子翻转恢复(SEUR)效应。分析了NMOS晶体管电荷共享导致SEUR效应的物理机制,系统研究了NMOS晶体管偏置(如电源电压、P阱偏置电压)和工艺参数(如P+深阱掺杂浓度、P阱接触距离)对线性能量传输翻转恢复阈值(LETrec)以及单粒子翻转脉冲宽度(PWrec)的影响。研究发现:PWrec随着电源电压的增大而增大;PWrec和LETrec随着P阱偏置电压的增大而减小;LETrec随着P+深阱掺杂浓度的增大而增大;PWrec随着P阱接触与NMOS晶体管之间距离的增大而增大,而LETrec随着P阱接触与NMOS晶体管之间距离增大而减小。本文研究结论有助于优化SRAM单元抗单粒子效应设计,尤其是基于SEUR效应的SRAM单元的抗辐照加固设计提供了理论指导。