柑橘皮提取液绿色合成纳米Fe3O4及其吸附水中孔雀石绿的性能研究

以柑橘皮提取液为还原剂和稳定剂,绿色合成Fe3O4纳米材料,利用扫描电子显微镜(SEM)、X射线衍射图谱(XRD)、傅立叶变换红外光谱(FT-IR)等手段对材料进行表征,并考察了其对孔雀石绿(MG)的吸附性能。结果表明:绿色合成纳米Fe3O4呈不规则圆球体,分散性和结晶度较好。在投加量为1.0 g/L、初始pH为4、温度为25℃、初始浓度为20 mg/L时,对孔雀石绿的吸附率达到95.33%。纳米Fe3O4对MG的吸附过程分别符合准二级动力学方程和Langmuir等温方程。热力学研究表明,纳米Fe3O4吸附MG是自发吸热过程。绿色合成纳米Fe3O4重复利用4次吸附率仍在70%以上。

Fe3O4@Zr-MOF的制备及其去除废水中氨氮的性能和机理分析

为高效去除废水中的氨氮,采用水热法合成了四氧化三铁@锆基金属有机框架(Fe_(3)O_(4)@Zr-MOF)材料,采用SEM、XRD、BET等技术对其进行了表征,通过静态吸附试验探究了吸附材料投加量、氨氮初始浓度、pH值、反应时间对模拟废水中氨氮吸附效果的影响,并进行了吸附等温线及吸附动力学拟合,最后采用FTIR、XPS法对其吸附机理进行了分析。结果表明:在中性条件下Fe_(3)O_(4)@Zr-MOF投加量为1 g/L时,其对模拟废水中的氨氮具有较好的吸附效果,吸附过程在6 h基本达到平衡;当氨氮初始浓度为50 mg/L时,Fe_(3)O_(4)@Zr-MOF对氨氮的平衡吸附量为47.18 mg/g,去除率为94.41%;吸附等温线拟合结果表明Fe_(3)O_(4)@Zr-MOF吸附水体中氨氮符合Langmuir吸附模型(R^(2)=0.981),该吸附行为是发生在吸附剂表面的单分子层吸附;吸附动力学拟合结果表明伪二阶动力学曲线(R^(2)=0.993)对试验数据有更优的拟合效果,该吸附为典型的化学吸附;使用0.5 mol/L的HCl作为解吸剂进行解吸再生试验,5次循环后吸附量及解吸率分别仅下降了6.63%和4.85%,表明该复合材料有良好的重复使用性能;Fe_(3)O_(4)@Zr-MOF吸附氨氮的吸附机理为Fe—O—Fe、Zr—O—Zr通过配体交换作用形成了Fe—O—N、Zr—O—N,从而能够高效吸附水体中的氨氮。该研究可为吸附材料的开发与应用提供参考。

Heterogeneous catalytic activation of peroxymonosulfate for efficient degradation of organic pollutants by magnetic Cu^0/Fe_3O_4 submicron composites

Magnetic Cu^0/Fe3O4 submicron composites were prepared using a hydrothermal method and used as heterogeneous catalysts for the activation of peroxymonosulfate（PMS） and the degradation of organic pollutants.The as-prepared magnetic Cu^0/Fe3O4 submicron composites were composed of Cu^0 and Fe3O4 crystals and had an average size of approximately 220 nm.The Cu^0/Fe3O4 composites could efficiently catalyze the activation of PMS to generate singlet oxygen,and thus induced the rapid degradation of rhodamine B,methylene blue,orange Ⅱ,phenol and 4-chlorophenol.The use of0.1 g/L of the Cu^0/Fe3O4 composites induced the complete removal of rhodamine B（20 μmol/L） in15 min,methylene blue（20 μmol/L） in 5 min,orange Ⅱ（20 μmol/L） in 10 min,phenol（0.1mmol/L） in 30 min and 4-chlorophenol（0.1 mmol/L） in 15 min with an initial pH value of 7.0 and a PMS concentration of 0.5 mmol/L.The total organic carbon（TOC） removal higher than 85%for all of these five pollutants was obtained in 30 min when the PMS concentration was 2.5 mmol/L.The rate of degradation was considerably higher than that obtained with Cu^0 or Fe3O4 particles alone.The enhanced catalytic activity of the Cu^0/Fe3O4 composites in the activation of PMS was attributed to the synergistic effect of the Cu^0 and Fe3O4 crystals in the composites.Singlet oxygen was identified as the primary reactive oxygen species responsible for pollutant degradation by electron spin resonance and radical quenching experiments.A possible mechanism for the activation of PMS by Cu^0/Fe3O4 composites is proposed as electron transfer from the organic pollutants to PMS induces the activation of PMS to generate ^1O2,which induces the degradation of the organic pollutants.As a magnetic catalyst,the Cu^0/Fe3O4 composites were easily recovered by magnetic separation,and exhibited excellent stability over five successive degradation cycles.The present study provides a facile and green heterogeneous catalysis method for the oxidative removal of organic pollutants.

Na_(2)CO_(3)·10H_(2)O-Na_(2)HPO_(4)·12H_(2)O/SiO_(2)复合定形相变材料的制备及应用

以Na_(2)CO_(3)·10H_(2)O(SCD)、Na_(2)HPO_(4)·12H_(2)O(DHPD)为相变主体制备了共晶体系,通过绘制凝固点变化图与DSC测试共同确定在m(SCD)∶m(DHPD)=4∶6时形成共晶,FTIR和XRD结果显示,2种水合盐间没有发生化学反应,但其晶型结构发生改变。通过添加质量分数为2%的Na2SiO3·9H_(2)O作为成核剂降低体系的过冷度,且经历50次相变循环体系未出现相分离,相变焓值仅下降0.25%。进一步使用质量分数为25%的气相SiO_(2)作为支撑材料,采用浸渍法制备了相变前后形状稳定的共晶水合盐/SiO_(2)定形相变材料(SSPCM)。所得SSPCM的相变温度为24.08℃,相变焓值为146.6J/g,过冷度为0.55℃,热导率为0.4571W/(m·K)。同保温泡沫相比,其可将模拟房内部中心温度的升温时间延长了1.81倍,降温时间延长了0.39倍。

Preparation and properties of a nano TiO_2/Fe_3O_4 composite superparamagnetic photocatalyst

Nano TiO2/Fe3O4 composite particles with different molar ratios of TiO2 to Fe3O4 were prepared via sol-gel method. X-ray diffraction, transmission electron microscopy, and vibration sample magnetometry were used to characterize the TiO2/Fe3O4 particles. The photocatalytic activity of the particles was tested by degrading methyl blue solution under UV illumination （254 nm）. The results indicate that with the content of TiO2 increasing, the photocatalytic activity of the composite particles enhances, while the magnetism of the particles decreases. When the molar ratio of TiO2 to Fe3O4 is about 8, both the photocatalytic activity and magnetism of the TiO2/Fe3O4 particles are relatively high, and their photocatalytic activity remains well after repeated use.

RhB Adsorption Performance of Magnetic Adsorbent Fe_3O_4/RGO Composite and Its Regeneration through A Fenton-like Reaction

Adsorption is one of the most effective technologies in the treatment of colored matter containing wastewater. Graphene related composites display potential to be an effective adsorbent. However, the adsorption mechanism and their regeneration approach are still demanding more efforts. An effective magnetically separable absorbent, Fe3O4 and reduced graphene oxide(RGO) composite has been prepared by an in situ coprecipitation and reduction method. According to the characterizations of TEM, XRD, XPS, Raman spectra and BET analyses, Fe3O4 nanoparticles in sizes of 10-20 nm are well dispersed over the RGO nanosheets, resulting in a highest specific area of 296.2 m2/g. The rhodamine B adsorption mechanism on the composites was investigated by the adsorption kinetics and isotherms. The isotherms are fitting better by Langmuir model, and the adsorption kinetic rates depend much on the chemical components of RGO. Compared to active carbon, the composite shows 3.7 times higher adsorption capacity and thirty times faster adsorption rates. Furthermore,with Fe3O4 nanoparticles as the in situ catalysts, the adsorption performance of composites can be restored by carrying out a Fenton-like reaction, which could be a promising regeneration way for the adsorbents in the organic pollutant removal of wastewater.

Magnetic Fe_3O_4-Reduced Graphene Oxide Nanocomposites-Based Electrochemical Biosensing

An electrochemical biosensing platform was developed based on glucose oxidase(GOx)/Fe3O4-reduced graphene oxide(Fe3O4-RGO) nanosheets loaded on the magnetic glassy carbon electrode(MGCE).With the advantages of the magnetism, conductivity and biocompatibility of the Fe3O4-RGO nanosheets, the nanocomposites could be facilely adhered to the electrode surface by magnetically controllable assembling and beneficial to achieve the direct redox reactions and electrocatalytic behaviors of GOx immobilized into the nanocomposites. The biosensor exhibited good electrocatalytic activity, high sensitivity and stability. The current response is linear over glucose concentration ranging from 0.05 to 1.5 m M with a low detection limit of0.15 μM. Meanwhile, validation of the applicability of the biosensor was carried out by determining glucose in serum samples. The proposed protocol is simple, inexpensive and convenient, which shows great potential in biosensing application.

Absorption performance of DMSA modified Fe_3O_4@SiO_2 core/shell magnetic nanocomposite for Pb^(2+) removal

The purpose of this study is to explore the adsorption performance of meso-2,3-dimercaptosuccinic acid(DMSA)modified Fe3O4@SiO2 magnetic nanocomposite(Fe3O4@SiO2@DMSA)for Pb2+ions removal from aqueous solutions.The effects of solution pH,initial concentration of Pb2+ions,contact time,and temperature on the amount of Pb2+adsorbed were investigated.Adsorption isotherms,adsorption kinetics,and thermodynamic analysis were also studied.The results showed that the maximum adsorption capacity of the Fe3O4@SiO2@DMSA composite is 50.5 mg/g at 298 K,which is higher than that of Fe3O4 and Fe3O4@SiO2 magnetic nanoparticles.The adsorption process agreed well with Langmuir adsorption isotherm models and pseudo second-order kinetics.The thermodynamic analysis revealed that the adsorption was spontaneous,endothermic and energetically driven in nature.

Removing Cd^(2+) by Composite Adsorbent Nano-Fe_3O_4/Bacterial Cellulose

A new composite adsorbent, nano-Fe3O4/bacterial cellulose（BC）, was prepared through blending method. The process of adsorbing Cd2＋ including its isotherm and kinetics measured was studied. The results show that the adsorption efficiency is improved because of huge surface area and surface coordination of nano-Fe3O4 particles. Its adsorption capacity is 27.97 mg/g and the maximum of Cd2＋ removal is 74%. The adsorption kinetics can be described by pseudo-second rate model and the adsorption equilibrium by Langmuir type. The superparamagnetism of nano-Fe3O4 particles can help to solve the difficult separation of single BC adsorbent and lead to the quick separation of composite adsorbent from the liquid if a magnetic field was applied. Cd2＋ can be desorbed effectively by EDTA and HCl from the composite adsorbent, which can make it be reused.

Enhanced Fenton,photo-Fenton and peroxidase-like activity and stability over Fe_3O_4/g-C_3N_4 nanocomposites

We prepared the Fe3O4/g‐C3N4nanoparticles(NPs)through a simple electrostatic self‐assembly method with a3:97weight ratio to investigate their Fenton,photo‐Fenton and oxidative functionalities besides photocatalytic functionality.We observed an improvement of the Fenton and photo‐Fenton activities of the Fe3O4/g‐C3N4nanocomposites.This improvement was attributed to efficient charge transfer between Fe3O4and g‐C3N4at the heterojunctions,inhibition of electron‐hole recombination,a high surface area,and stabilization of Fe3O4against leaching by the hydrophobic g‐C3N4.The obtained NPs showed a higher degradation potential for rhodamine B(RhB)dye than those of Fe3O4and g‐C3N4.As compared to photocatalysis,the efficiency of RhB degradation in the Fenton and photo‐Fenton reactions was increased by20%and90%,respectively.Additionally,the horseradish peroxidase(HRP)activity of the prepared nanomaterials was studied with3,3,5,5‐tetramethylbenzidinedihydrochloride(TMB)as a substrate.Dopamine oxidation was also examined.Results indicate that Fe3O4/g‐C3N4nanocomposites offers more efficient degradation of RhB dye in a photo‐Fenton system compared with regular photocatalytic degradation,which requires a long time.Our study also confirmed that Fe3O4/g‐C3N4nanocomposites can be used as a potential material for mimicking HRP owing to its high affinity for TMB.These findings suggest good potential for applications in biosensing and as a catalyst in oxidation reactions.

Effect of Al2O3np on the Properties and Microstructure of B4Cp/Al Composites

Aluminum-matrix boron carbide (B4Cp/Al) is a kind of neutron absorbing material widely used in nuclear spent fuel storage. In order to improve the tensile property of B4Cp/Al composites, a new type of nano-Al2O3 particle (Al2O3np) reinforced B4Cp/Al + Al2O3np composites were prepared by powder metallurgy method. The Monte Carlo particle transport program (MCNP) was used to determine the influence of Al2O3np on the thermal neutron absorptivity of composites. The universal material testing machine and scanning electron microscope (SEM) were used to study the mechanical properties, microstructure and fracture morphology of B4Cp/Al composites. The results indicated that the neutron absorption properties of B4Cp/Al composites were not affected by the addition of nano-Al2O3 particles in the range of 1 wt%-15 wt%. The addition of Al2O3np can obviously reduce the grain size of B4Cp/Al matrix metals thus improve the tensile strength of the composites. The addition threshold of Al2O3np is about 2.5 wt%. Both B4Cp and Al2O3np change the fracture characteristics of the composites from toughness to brittleness, and the latter is more important.

Synthesis and microwave absorption properties of graphene-oxide(GO)/polyaniline nanocomposite with Fe_3O_4 particles

In order to investigate the impedance matching properties of microwave absorbers,the ternary nanocomposites of GO/PANI/Fe3O4（GPF） are prepared via a two-step method,GO/PANI composites are synthesized by dilute polymerization in the presence of aniline monomer and GO,and GO/PANI/Fe3O4 is prepared via a co-precipitation method.The obtained nanocomposites are characterized by scanning electron microscopy（SEM）,X-ray diffraction（XRD）,and Fourier transform infrared spectroscopy（FTIR）,respectively.The microwave absorbability reveals enhanced microwave absorption properties compared with GO,PANI,and GO/PANI.The maximum reflection loss of GO/PANI/Fe3O4 is up to-27 dB at 14 GHz with its thickness being 2 mm,and its absorption bandwidths exceeding-10 dB are more than 11.2 GHz with its thickness values being in the range from 1.5 mm-4 mm.It provides that GO/PANI/Fe3O4 can be used as an attractive candidate for microwave absorbers.

Preparation and Characterization of Superparamagnetic Fe_3O_4/CNTs Nanocomposites Dual-drug Carrier

Fe3O4/carbon nanotubes（Fe3O4/CNTs） nanocomposites were prepared by polylol hightemperature decomposition of the precursor ferric chloride and CNTs in liquid triethylene glycol.After surface modification with hexanediamine,folate was covalently linked to the amine group of magnetic Fe3O4/CNTs nanocomposites.The products were characterized by Fourier-transform infrared spectroscopy,transmission electron microscopy,and vibrating sample magnetometry.Then Fe3O4/CNTs were used as a dual-drug carrier to co-delivery of the hydrophilic drug epirubicin hydrochloride and hydrophobic drug paclitaxel.The results indicated that the Fe3O4/CNTs had a favorable release property for epirubicin and paclitaxel,and thus had potential application in tumor-targeted combination chemotherapy.

Facile Fabrication of Fe2O3/Nitrogen Deficient g-C3N4-x Composite Catalysts with Enhanced Photocatalytic Performances

The modification of graphitic carbon nitride can significantly improve the photocatalytic performance of graphitic carbon nitride(g-C3N4).Fe2O3/nitrogen-deficient g-C3N4-x composite catalysts were prepared with dicyandiamide as the precursor and Fe3+doped in this study.The composite catalysts were characterized by XRD,SEM,FT-IR,XPS and photocurrent measurements.Close interaction occurred between Fe2O3 and nitrogen deficient g-C3N4-x,more photogenerated electrons were created and effectively separated from the holes,resulting in a decrease of photocarrier recombination,and thus enhancing the photocurrent.Photocatalytic performance experiments showed that Fe2O3/nitrogen deficient g-C3N4-x could utilize lowenergy visible light more efficiently than pure g-C3N4,and the removal rate was 92%in 60 minutes.

Synthesis of Fe_3O_4-coated silica aerogel nanocomposites

Fe3O4:SiO2 nanocomposite powders were synthesized by a two-step process,which included the precipitation of FeCl2 and FeCl3 and the gelation of silicic acid solution derived from water glass.At first,Fe3O4 nanoparticles having a crystallite size of 20 nm were obtained by controlling the ratio of Fe(II) and Fe(III) precursors.In the second step,Fe3O4 particles were embedded in SiO2 matrix by the hydrolysis and subsequent condensation of the silicic acid solution containing Fe3O4 particles.It was found that the Fe3O4 nanoparticles homogenously disperse in the SiO2 matrix.The Fe3O4:SiO2 nanocomposite exhibited an enhanced thermal stability against oxidation compared with pure Fe3O4.FT-IR analysis indicates the presence of the Si-O-Fe bond in the Fe3O4:SiO2 (1:10,mole fraction) nanocomposite.

A simple method for purification of genomic DNA from whole blood using Fe_3O_4/Au composite particles as a carrier

Objective： To establish a method of genomic DNA extraction from whole blood using Fe3O4/Au composite particles as a carrier. Methods： Two crucial conditions （sodium chloride concentration and amount of the magnetic particles） were optimized and 8 different human whole blood samples were used to purify genomic DNA under the optimal condition. Then agarose gel electrophoresis and polymerase cbain reaction （PCR） were performed. Results： The optimal binding condition was 1.5 mol/L NaC1/10% PEG, and the optimal amount of Fe3O4/Au composite particles was 600μg. The yields of the genomic DNA from 100μl of different whole blood samples were 2-5 μg, and the ratio of A260/A280 was in the range of 1.70-1.90. The size of genomic DNA was about 23 kb and the PCR was valid. Conclusion： The purification system using Fe3O4/Au composite microparticles has advantages in high yield, high purity, ease of operating, time saving and avoiding centrifugation. The purified sample was found to function satisfactorily in PCR amplification.

Application of Polymerizable Surfactant in the Preparation of Polystyrene/Nano-Fe_3O_4 Composite

Monooctadecyl maleate, as a polymerizable surfactant, was synthesized by the mono-esterification of maleic anhydride and octadecanol, and was utilized to surface-modify nano-Fe3O4 particles. A polymerizable magnetic fluid was obtained by directly dispersing modified nano-Fe3O4 particles into styrene monomer, and the polystyrene/nano-Fe3O4 composite was prepared through free radical polymerization of polymerizable magnetic fluid. The structure and dispersion status in different dispersion phases of modified nano-Fe3O4 particles were studied by Fourier transform infrared （FTIR） spectrometry, X-ray diffraction （XRD） and transmission electron microscopy （TEM）, respectively. The experimental results show that the nano-Fe3O4 particles modified by monooctadecyl maleate with the size of about 7-10 nm can be uniformly dispersed into styrene and fixed in the composite during the procedure of polymerization. Thermogravimetric analysis （TGA） and vibrating sample magnetometry （VSM） indicate that the thermal stability of polystyrene/nano-Fe3O4 composite is improved compared to that of pure polystyrene, and the composite is a sort of superparamagnetic materials.

Synthesis of Y_2O_3 particle enhanced Ni/TiC composite on TC4 Ti alloy by laser cladding

A Y2O3 particle enhanced Ni/TiC composite coating was fabricated in-situ on a TC4 Ti alloy by laser surface cladding. The phase component, microstructure, composition distribution and properties of the composite layer were investigated. The composite layer has graded microstructures and compositions, due to the fast melting followed by rapid solidification and cooling during laser cladding. The TiC powders are completely dissolved into the melted layer during melting and segregated as fine dendrites when solidified. The size of TiC dendrites decreases with increasing depth. Y2O3 fine particles distribute in the whole clad layer. The Y2O3 particle enhanced Ni/TiC composite layer has a quite uniform hardness along depth with a maximum value of HV1380, which is 4 times higher than the initial hardness. The wear resistance of the Ti alloy is significantly improved after laser cladding due to the high hardness of the composite coating.

Synthesis and Characterization of Superparamagnetic Fe₃O₄@SiO₂Core-Shell Composite Nanoparticles

The Fe3O4@SiO2 composite nanoparticles were obtained from as-synthesized magnetite (Fe3O4) nanoparticles through the modified St?ber method. Then, the Fe3O4 nanoparticles and Fe3O4@SiO2 composite nanoparticles were characterized by means of X-ray diffraction (XRD), Raman spectra, scanning electron microscope (SEM) and vibrating sample magnetometer (VSM). Recently, the studies focus on how to improve the dispersion of composite particle and achieve good magnetic performance. Hence effects of the volume ratio of tetraethyl orthosilicate (TEOS) and magnetite colloid on the structural, morphological and magnetic properties of the composite nanoparticles were systematically investi-gated. The results revealed that the Fe3O4@SiO2 had better thermal stability and dispersion than the magnetite nanoparticles. Furthermore, the particle size and magnetic property of the Fe3O4@SiO2 composite nanoparticles can be adjusted by changing the volume ratio of TEOS and magnetite colloid.

Ag_(3)PO_(4)/Cu_(2)O复合材料的制备及其性能研究

对磷酸银复合材料制备及光催化性能进行了研究。讨论了水热温度、反应溶液的酸碱度等对Cu_(2)O制备的影响。同时,比较了不同摩尔百分比Ag_(3)PO_(4)含量的Ag_(3)PO_(4)/Cu_(2)O复合材料的光催化降解活性。结果显示,球状Cu_(2)O颗粒制备条件为:温度100℃,pH值为10。采用直接沉淀法Ag_(3)PO_(4)纳米颗粒能够均匀附着Cu_(2)O表面,达到最佳复合效果。Ag_(3)PO_(4)/Cu_(2)O复合材料光催化活性高于纯Cu_(2)O,随着Ag_(3)PO_(4)的摩尔百分量的增加,复合光催化剂的催化性能先是增强后逐渐减弱。60%Ag_(3)PO_(4)/Cu_(2)O时,催化活性最强,90 min内罗丹明B几乎完全降解。