To meet the demand for high-performance LiCoO_(2) batteries,it is necessary to overcome challenges such as interface degradation and rapid capacity degradation caused by changes in bulk structure,especially under deep...To meet the demand for high-performance LiCoO_(2) batteries,it is necessary to overcome challenges such as interface degradation and rapid capacity degradation caused by changes in bulk structure,especially under deep delithiation and high temperature conditions.The ion conductive coating layer of Li_(3)PO_(4) has been directly modified on the surface of LiCoO_(2) particles using magnetron sputtering method,significantly improving the lithium storage performance of LiCoO_(2)@Li_(3)PO_(4) composites.Compared to pure LiCoO_(2),the modified LiCoO_(2) sample exhibits obviously better cycle life and high-temperature performance.Especially,under the conditions of 2 and 1 C,the LiCoO_(2)@Li_(3)PO_(4) electrode delivers excellent cycling performance at high voltage of 4.5 V,with capacity retention rates of 89.7%and 75.7%at room temperature and high temperature of 45℃,being far greater than those of 12.3%and 29.1%for bare LiCoO_(2) electrodes.It is discovered that the Li_(3)PO_(4) coating layer not only effectively enhances interface compatibility and suppresses the irreversible phase transition of LiCoO_(2),but also further improves the Li^(+)transport kinetics and significantly reduces battery polarization,ultimately enabling the modified LiCoO_(2) electrode to exhibit excellent lithium storage performance and thermal safety characteristics under high voltage conditions.Thus,such effective modified strategy can undoubtedly provide an important academic inspiration for LiCoO_(2) implication.展开更多
The effect of molybdenum oxide on the activity and durability of Ce O2-Ti O2 catalyst for NO reduction by NH3 was examined. It was found that the introduction of Mo could improve the low-temperature NH3-SCR activity a...The effect of molybdenum oxide on the activity and durability of Ce O2-Ti O2 catalyst for NO reduction by NH3 was examined. It was found that the introduction of Mo could improve the low-temperature NH3-SCR activity and SO2/H2 O durability of the Ce O2-Ti O2 catalyst and an optimal loading of Mo was 4?wt.%. The best Mo O3/Ce O2-Ti O2 catalyst displayed over 90% NO conversion from 200 °C to 400 °C and obtained 4-fold increase in NO conversion compared to Ce O2-Ti O2 at 150 °C. The characterization results revealed that the number of Br?nsted acid sites over Mo O3/Ce O2-Ti O2 was significantly increased, and the adsorption of nitrate species was dramatically weakened because of the coverage of Mo O3, which were favorable for the high NH3-SCR performance. It is believed that the Mo O3/Ce O2-Ti O2 catalyst is a suitable substitute for the NH3-SCR reaction.展开更多
Fe3O4 nanoparticles were prepared by chemistry co-precipitation and the mean crystal size was 17.9 nm measured by XRD. After it had been treated by silane-coupling agents KH570, magnetic micro-spheres dispersed in org...Fe3O4 nanoparticles were prepared by chemistry co-precipitation and the mean crystal size was 17.9 nm measured by XRD. After it had been treated by silane-coupling agents KH570, magnetic micro-spheres dispersed in organic medium glycol were gained and the mean size of Fe3O4 nanopowders was 33.7 nm. So it can be concluded that magnetic micro-sphere is made of a few Fe3O4 crystals. Many factors of modification were researched, such as the time of ball milling, the content of Fe3O4 and the content of KH570. The modification of Fe3O4 is relative to the time of ball milling, but the dominant function is affected by the content of Fe3O4 and KH570. When the content of Fe3O4 is known, there is a suitable content of KH570. Different content of Fe3O4 will make the different suitable content of KH570, but the range of latter is less than former, which is relative to the distribution of KH570 on Fe3O4 surface or in the solution.展开更多
Up to now the mechanism of Priedel-Crafts reactions catalyzed by ionic liquidhave not been fully understood, while carbocation mechanism was assumed. It was found that thesource of H^+ and the route of reaction initia...Up to now the mechanism of Priedel-Crafts reactions catalyzed by ionic liquidhave not been fully understood, while carbocation mechanism was assumed. It was found that thesource of H^+ and the route of reaction initiated the alkylation of benzene with ethylene catalyzedby [bmim]Cl/FeCl_3 ionic liquid. The fact that dewatered ionic liquids have catalytic activity forthe alkylation of benzene with ethylene suggests that there exists a new catalytic route. Thedistinctly Bronsted acid properties of 2-H in [bmim]Cl were found through FT-IR and HNMR analysis of[bmim]Cl after titration with water free KOH in alcohol solution. In addition, the chemical shiftsof proton on the [bmim]Cl ring, especially 2-H, are sensitive to the change of FeCl_3 content andshifted downfield when FeCl_3 was added into [bmim]Cl to form ionic liquid. Thus 2-H was easy to bedisengaged from imidazolium ring with formation of H^+ to initiate the reaction. Theisotope-substituted method was employed to prove this mechanism, through the GC-MS analysis ofalkylation products of deuterated benzene with ethylene. The route of alkylation catalyzed by FeCl_3ionic liquid was found to follow the carbocation mechanism, the resource of H^+ was presented andproved using HNMR analysis of ionic liquid to inspect the intensity change of 2-H. It was found thatthe intensity of 2-H reduced 23% after reaction showing that the H^+ arising from alkylationreaction was supplied by 2-H on the imidazole ring.展开更多
Membrane fouling is always the biggest problem in the practice of membrane separation technologies,which strongly impacts their applicability,separation efficiency,cost effectiveness,and service lifespan.Herein,a simp...Membrane fouling is always the biggest problem in the practice of membrane separation technologies,which strongly impacts their applicability,separation efficiency,cost effectiveness,and service lifespan.Herein,a simple but effective 3D modification approach was designed for permanently functionalizing polymeric membranes by directly cross-linking polyvinyl alcohol(PVA)under gamma-ray irradiation at room temperature without any additives.After the modification,a PVA layer was constructed on the membrane surface and the pore inner surface of polyvinylidene fluoride(PVDF)membranes.This endowed them with good hydrophilicity,low adsorption of protein model foulants,and easy recoverability properties.In addition,the pore size and distribution were customized by controlling the PVA concentration,which enhanced the rejection ability of the resultant membranes and converted them from microfiltration to ultrafiltration.The crosslinked PVA layer was equipped with the resultant membranes with good resistance to chemical cleaning by acidic,alkaline,and oxidative reagents,which could greatly prolong the membrane service lifetime.Furthermore,this approach was demonstrated as a universal method to modify PVDF membranes with other hydrophilic macromolecular modifiers,including polyethylene glycol,sodium alginate,and polyvinyl pyrrolidone.This modification of the membranes effectively endowed them with good hydrophilicity and antifouling properties,as expected.展开更多
In this work,we synthesized LaFeO_3–xwt%Ni(x=0,5,10,15)composites via a solid-state reaction method by adding Ni to the reactants,La_2O_3 and Fe_2O_3.Field-emission scanning electron microscopy(FE-SEM)and energy-disp...In this work,we synthesized LaFeO_3–xwt%Ni(x=0,5,10,15)composites via a solid-state reaction method by adding Ni to the reactants,La_2O_3 and Fe_2O_3.Field-emission scanning electron microscopy(FE-SEM)and energy-dispersive X-ray spectroscopy(EDS)results revealed that Ni powders evenly dispersed among the LaFeO_3 particles and apparently reduced their aggregation,which imparted the composites with a loose structure.Moreover,the Ni formed a conductive network,thus improving the conductivity of the composites.The maximum discharge capacity of the LaFeO_3 electrodes remarkably increased from 266.8 mAh·g^(–1)(x=0)to 339.7 mAh·g^(–1)(x=10).In particular,the high-rate dischargeability of the LaFeO_3–10wt%Ni electrode at a discharge current density of 1500 mA·g^(-1) reached 54.6%,which was approximately 1.5 times higher than that of the pure LaFeO_3.Such a Ni-modified loose structure not only increased the charge transfer rate on the surface of the LaFeO_3 particles but also enhanced the hydrogen diffusion rate in the bulk LaFeO_3.展开更多
The surface organic modification of Fe3O4 nanoparticles with silane coupling reagent KH570 was studied. The modified and unmodified nanoparticles were characterized by FT-IR, XPS and TEM. The spectra of FT-IR and XPS ...The surface organic modification of Fe3O4 nanoparticles with silane coupling reagent KH570 was studied. The modified and unmodified nanoparticles were characterized by FT-IR, XPS and TEM. The spectra of FT-IR and XPS revealed that KH570 was coated onto the surface of Fe3O4 nanoparticles to get Fe-O- Si bond and an organic coating layer also was formed. Fe3O4 nanoparticles were spheres partly with mean size of 18,8 nm studied by TEM, which was consistent with the result 17.9 nm calculated by Scherrer＇s equation. KH570 was adsorbed on surface and formed chemistry bond to be steric hindrance repulsion which prevented nanoparticles from reuniting. Then glycol-based Fe3O4 magnetic liquids dispersed stably was gained.展开更多
The modification effects of ytterbium(Yb), Na_3PO_4 and Yb + Na_3PO_4 on primary Mg_2Si phase in Mg-4Si alloys were investigated by means of X-ray diffraction(XRD), optical microscopy(OM), scanning electron microscopy...The modification effects of ytterbium(Yb), Na_3PO_4 and Yb + Na_3PO_4 on primary Mg_2Si phase in Mg-4Si alloys were investigated by means of X-ray diffraction(XRD), optical microscopy(OM), scanning electron microscopy(SEM) and energy dispersive spectroscopy(EDS) analysis in this work. The results indicate that the morphology of the primary Mg_2Si phase apparently changes from coarse dendrites to fine dispersive polygonal particles and the mean size decreases from 276.6 μm to 7.1 μm, with combined modification of 0.8wt.% Yb and 2.64 wt.% Na_3PO_4. Such a morphological evolution results in improvement in the ultimate tensile strength and elongation of the alloys as compared to the base alloy. This may be attributed to the formation of the YbP particles that acted as the heterogeneous nucleation substrates for the primary Mg_2Si particles, resulting in a refined distribution of these precipitates. The results of XRD examination show that there was no reaction between Si and Yb or Na_3PO_4. Solo addition of Yb or Na_3PO_4 into the melt has no real modification effect on the microstructure, but the primary Mg_2Si particles and α-Mg phases become coarser than that in the unmodified alloy.展开更多
基金jointly supported by the Natural Science Foundations of China(No.22179020,12174057)Fujian Province’s“Young Eagle Program”Youth Top Talents Program。
文摘To meet the demand for high-performance LiCoO_(2) batteries,it is necessary to overcome challenges such as interface degradation and rapid capacity degradation caused by changes in bulk structure,especially under deep delithiation and high temperature conditions.The ion conductive coating layer of Li_(3)PO_(4) has been directly modified on the surface of LiCoO_(2) particles using magnetron sputtering method,significantly improving the lithium storage performance of LiCoO_(2)@Li_(3)PO_(4) composites.Compared to pure LiCoO_(2),the modified LiCoO_(2) sample exhibits obviously better cycle life and high-temperature performance.Especially,under the conditions of 2 and 1 C,the LiCoO_(2)@Li_(3)PO_(4) electrode delivers excellent cycling performance at high voltage of 4.5 V,with capacity retention rates of 89.7%and 75.7%at room temperature and high temperature of 45℃,being far greater than those of 12.3%and 29.1%for bare LiCoO_(2) electrodes.It is discovered that the Li_(3)PO_(4) coating layer not only effectively enhances interface compatibility and suppresses the irreversible phase transition of LiCoO_(2),but also further improves the Li^(+)transport kinetics and significantly reduces battery polarization,ultimately enabling the modified LiCoO_(2) electrode to exhibit excellent lithium storage performance and thermal safety characteristics under high voltage conditions.Thus,such effective modified strategy can undoubtedly provide an important academic inspiration for LiCoO_(2) implication.
基金supported by the National Natural Science Foundation of China(21773106,21707066,21677069,and 21806077)the China Postdoctoral Science Foundation(2018M642206)~~
文摘The effect of molybdenum oxide on the activity and durability of Ce O2-Ti O2 catalyst for NO reduction by NH3 was examined. It was found that the introduction of Mo could improve the low-temperature NH3-SCR activity and SO2/H2 O durability of the Ce O2-Ti O2 catalyst and an optimal loading of Mo was 4?wt.%. The best Mo O3/Ce O2-Ti O2 catalyst displayed over 90% NO conversion from 200 °C to 400 °C and obtained 4-fold increase in NO conversion compared to Ce O2-Ti O2 at 150 °C. The characterization results revealed that the number of Br?nsted acid sites over Mo O3/Ce O2-Ti O2 was significantly increased, and the adsorption of nitrate species was dramatically weakened because of the coverage of Mo O3, which were favorable for the high NH3-SCR performance. It is believed that the Mo O3/Ce O2-Ti O2 catalyst is a suitable substitute for the NH3-SCR reaction.
基金This work was financially supported by the Graduate Innovation Plan Projects of Jiangsu Province in 2005.
文摘Fe3O4 nanoparticles were prepared by chemistry co-precipitation and the mean crystal size was 17.9 nm measured by XRD. After it had been treated by silane-coupling agents KH570, magnetic micro-spheres dispersed in organic medium glycol were gained and the mean size of Fe3O4 nanopowders was 33.7 nm. So it can be concluded that magnetic micro-sphere is made of a few Fe3O4 crystals. Many factors of modification were researched, such as the time of ball milling, the content of Fe3O4 and the content of KH570. The modification of Fe3O4 is relative to the time of ball milling, but the dominant function is affected by the content of Fe3O4 and KH570. When the content of Fe3O4 is known, there is a suitable content of KH570. Different content of Fe3O4 will make the different suitable content of KH570, but the range of latter is less than former, which is relative to the distribution of KH570 on Fe3O4 surface or in the solution.
文摘Up to now the mechanism of Priedel-Crafts reactions catalyzed by ionic liquidhave not been fully understood, while carbocation mechanism was assumed. It was found that thesource of H^+ and the route of reaction initiated the alkylation of benzene with ethylene catalyzedby [bmim]Cl/FeCl_3 ionic liquid. The fact that dewatered ionic liquids have catalytic activity forthe alkylation of benzene with ethylene suggests that there exists a new catalytic route. Thedistinctly Bronsted acid properties of 2-H in [bmim]Cl were found through FT-IR and HNMR analysis of[bmim]Cl after titration with water free KOH in alcohol solution. In addition, the chemical shiftsof proton on the [bmim]Cl ring, especially 2-H, are sensitive to the change of FeCl_3 content andshifted downfield when FeCl_3 was added into [bmim]Cl to form ionic liquid. Thus 2-H was easy to bedisengaged from imidazolium ring with formation of H^+ to initiate the reaction. Theisotope-substituted method was employed to prove this mechanism, through the GC-MS analysis ofalkylation products of deuterated benzene with ethylene. The route of alkylation catalyzed by FeCl_3ionic liquid was found to follow the carbocation mechanism, the resource of H^+ was presented andproved using HNMR analysis of ionic liquid to inspect the intensity change of 2-H. It was found thatthe intensity of 2-H reduced 23% after reaction showing that the H^+ arising from alkylationreaction was supplied by 2-H on the imidazole ring.
基金This work was supported by the National Natural Science Foundation of China(Nos.11875313,12075153,and 11575277).
文摘Membrane fouling is always the biggest problem in the practice of membrane separation technologies,which strongly impacts their applicability,separation efficiency,cost effectiveness,and service lifespan.Herein,a simple but effective 3D modification approach was designed for permanently functionalizing polymeric membranes by directly cross-linking polyvinyl alcohol(PVA)under gamma-ray irradiation at room temperature without any additives.After the modification,a PVA layer was constructed on the membrane surface and the pore inner surface of polyvinylidene fluoride(PVDF)membranes.This endowed them with good hydrophilicity,low adsorption of protein model foulants,and easy recoverability properties.In addition,the pore size and distribution were customized by controlling the PVA concentration,which enhanced the rejection ability of the resultant membranes and converted them from microfiltration to ultrafiltration.The crosslinked PVA layer was equipped with the resultant membranes with good resistance to chemical cleaning by acidic,alkaline,and oxidative reagents,which could greatly prolong the membrane service lifetime.Furthermore,this approach was demonstrated as a universal method to modify PVDF membranes with other hydrophilic macromolecular modifiers,including polyethylene glycol,sodium alginate,and polyvinyl pyrrolidone.This modification of the membranes effectively endowed them with good hydrophilicity and antifouling properties,as expected.
基金financially supported by the National Natural Science Foundation of China(Nos.51771164,51571173,and 51701175)the National Postdoctoral Program for Innovative Talents of China(No.BX201700204)the Innovation Fund for the Graduate Students of Hebei Province(No.CXZZBS2017057)
文摘In this work,we synthesized LaFeO_3–xwt%Ni(x=0,5,10,15)composites via a solid-state reaction method by adding Ni to the reactants,La_2O_3 and Fe_2O_3.Field-emission scanning electron microscopy(FE-SEM)and energy-dispersive X-ray spectroscopy(EDS)results revealed that Ni powders evenly dispersed among the LaFeO_3 particles and apparently reduced their aggregation,which imparted the composites with a loose structure.Moreover,the Ni formed a conductive network,thus improving the conductivity of the composites.The maximum discharge capacity of the LaFeO_3 electrodes remarkably increased from 266.8 mAh·g^(–1)(x=0)to 339.7 mAh·g^(–1)(x=10).In particular,the high-rate dischargeability of the LaFeO_3–10wt%Ni electrode at a discharge current density of 1500 mA·g^(-1) reached 54.6%,which was approximately 1.5 times higher than that of the pure LaFeO_3.Such a Ni-modified loose structure not only increased the charge transfer rate on the surface of the LaFeO_3 particles but also enhanced the hydrogen diffusion rate in the bulk LaFeO_3.
基金the Natural Science Fund of Jiangsu province (No.BK2007586)Jiangsu Planned Projects(No.0701012B)for Postdoctoral Research Funds
文摘The surface organic modification of Fe3O4 nanoparticles with silane coupling reagent KH570 was studied. The modified and unmodified nanoparticles were characterized by FT-IR, XPS and TEM. The spectra of FT-IR and XPS revealed that KH570 was coated onto the surface of Fe3O4 nanoparticles to get Fe-O- Si bond and an organic coating layer also was formed. Fe3O4 nanoparticles were spheres partly with mean size of 18,8 nm studied by TEM, which was consistent with the result 17.9 nm calculated by Scherrer＇s equation. KH570 was adsorbed on surface and formed chemistry bond to be steric hindrance repulsion which prevented nanoparticles from reuniting. Then glycol-based Fe3O4 magnetic liquids dispersed stably was gained.
基金financially supported by the Fundamental Research Funds for Central Universities(Grant No.:XDJK2015B001)
文摘The modification effects of ytterbium(Yb), Na_3PO_4 and Yb + Na_3PO_4 on primary Mg_2Si phase in Mg-4Si alloys were investigated by means of X-ray diffraction(XRD), optical microscopy(OM), scanning electron microscopy(SEM) and energy dispersive spectroscopy(EDS) analysis in this work. The results indicate that the morphology of the primary Mg_2Si phase apparently changes from coarse dendrites to fine dispersive polygonal particles and the mean size decreases from 276.6 μm to 7.1 μm, with combined modification of 0.8wt.% Yb and 2.64 wt.% Na_3PO_4. Such a morphological evolution results in improvement in the ultimate tensile strength and elongation of the alloys as compared to the base alloy. This may be attributed to the formation of the YbP particles that acted as the heterogeneous nucleation substrates for the primary Mg_2Si particles, resulting in a refined distribution of these precipitates. The results of XRD examination show that there was no reaction between Si and Yb or Na_3PO_4. Solo addition of Yb or Na_3PO_4 into the melt has no real modification effect on the microstructure, but the primary Mg_2Si particles and α-Mg phases become coarser than that in the unmodified alloy.
