From Maxwell's equations and Post's formalism, a generalized chiral nonlinear Schr6dinger equation (CNLSE) is obtained for the nonlinear chiral fiber. This equation governs light transmission through a dispersive ...From Maxwell's equations and Post's formalism, a generalized chiral nonlinear Schr6dinger equation (CNLSE) is obtained for the nonlinear chiral fiber. This equation governs light transmission through a dispersive nonlinear chiral fiber with joint action of chirality in linear and nonlinear ways. The generalized CNLSE shows a modu- lation of chirality to the effect of attenuation and nonlinearity compared with the case for a conventional fiber. Simulations based on the split-step beam propagation method reveal the role of nonlinearity with cooperation to chirality playing in the pulse evolution. By adjusting its strength the role of chirality in forming solitons is demonstrated for a given circularly polarized component. The application of nonlinear optical rotation is also discussed in an all-optical switch.展开更多
We numerically study the pulse compression approaches based on atomic or molecular gases in a hollow-core fiber.From the perspective of self-phase modulation(SPM), we give the extensive study of the SPM influence on...We numerically study the pulse compression approaches based on atomic or molecular gases in a hollow-core fiber.From the perspective of self-phase modulation(SPM), we give the extensive study of the SPM influence on a probe pulse with molecular phase modulation(MPM) effect. By comparing the two compression methods, we summarize their advantages and drawbacks to obtain the few-cycle pulses with micro- or millijoule energies. It is also shown that the double pump-probe approach can be used as a tunable dual-color source by adjusting the time delay between pump and probe pulses to proper values.展开更多
Currently,artificial-membrane lungs consist of thousands of hollow fiber membranes where blood flows around the fibers and gas flows inside the fibers,achieving diffusive gas exchange.At both ends of the fibers,the in...Currently,artificial-membrane lungs consist of thousands of hollow fiber membranes where blood flows around the fibers and gas flows inside the fibers,achieving diffusive gas exchange.At both ends of the fibers,the interspaces between the hollow fiber membranes and the plastic housing are filled with glue to separate the gas from the blood phase.During a uniaxial centrifugation process,the glue forms the“potting.”The shape of the cured potting is then determined by the centrifugation process,limiting design possibilities and leading to unfavorable stagnation zones associated with blood clotting.In this study,a new multiaxial centrifugation process was developed,expanding the possible shapes of the potting and allowing for completely new module designs with potentially superior blood flow guidance within the potting margins.Two-phase simulations of the process in conceptual artificial lungs were performed to explore the possibilities of a biaxial centrifugation process and determine suitable parameter sets.A corresponding biaxial centrifugation setup was built to prove feasibility and experimentally validate four conceptual designs,resulting in good agreement with the simulations.In summary,this study shows the feasibility of a multiaxial centrifugation process allowing greater variety in potting shapes,eliminating inefficient stagnation zones and more favorable blood flow conditions in artificial lungs.展开更多
We theoretically analyze and experimentally demonstrate a method of generating equal-amplitude optical comb exploiting multi-frequency phase modulation. The theoretical analysis shows that 4n-1 equalamplitude spectral...We theoretically analyze and experimentally demonstrate a method of generating equal-amplitude optical comb exploiting multi-frequency phase modulation. The theoretical analysis shows that 4n-1 equalamplitude spectral lines can be obtained when the modulation signal comprises n frequency components including the fundamental frequency and the odd harmonic frequencies, and 2n+1 equal-amplitude spectral lines can be obtained when the modulation signal comprises n frequency components including the fundamental frequency and the even harmonic frequencies. Then, we numerically simulate the spectra of 5, 7, 9, and 11 equal-amplitude spectral lines, respectively, which are also obtained in experiments with frequency separation of 30 MHz and flatness of better than 0.3 dB.展开更多
Based on the high-speed development of the fiber laser in recent years, the development of researching 915 nm semiconductor laser as main pumping sources of the fiber laser is at a high speed. Because the beam quality...Based on the high-speed development of the fiber laser in recent years, the development of researching 915 nm semiconductor laser as main pumping sources of the fiber laser is at a high speed. Because the beam quality of the laser diode is very poor, the 915 nm laser diode is generally based on optical fiber coupling module to output the laser. Using the beam-shaping and fiber-coupling technology to improve the quality of output beam light, we present a kind of high-power and high-brightness semiconductor laser module, which can output 13.22 W through the optical fiber. Based on 915 nm GaAs semiconductor laser diode which has output power of 13.91 W, we describe a thoroughly detailed procedure for reshaping the beam output from the semiconductor laser diode and coupling the beam into the optical fiber of which the core diameter is 105 μm and the numerical aperture is 0.18. We get 13.22 W from the output fiber of the module at 14.5 A, the coupling efficiency of the whole module is 95.03% and the brightness is 1.5 MW/cm2-str. The output power of the single chip semiconductor laser module achieves the advanced level in the domestic use.展开更多
A tunable frequency-multiplying optoelectronic oscillator(OEO) based on a dual-parallel Mach-Zehnder modulator(DPMZM) is proposed and experimentally demonstrated. In the proposed system, the tunable fundamental microw...A tunable frequency-multiplying optoelectronic oscillator(OEO) based on a dual-parallel Mach-Zehnder modulator(DPMZM) is proposed and experimentally demonstrated. In the proposed system, the tunable fundamental microware signal is generated by a tunable optoelectronic oscillator incorporating a phase-shifted fiber Bragg grating(PS-FBG). By adjusting the DC bias of the DPMZM, the frequency-doubled microwave signal with a tunable frequency range from 11 GHz to 20 GHz and the frequency-quadrupled microwave signal with a tunable frequency range from 22.5 GHz to 26 GHz are generated. The phase noises of the fundamental, frequency-doubled and frequency-quadrupled signals at 10 k Hz offset frequency are-105.9 d Bc/Hz,-103.3 d Bc/Hz and-86.2 d Bc/Hz, respectively.展开更多
We report 20 Gb/s transmission of four-level pulse amplitude modulation (PAM) signal using a directly modulated tunable distributed Bragg reflector (DBR) laser. Transmission distance over 20 km was achieved withou...We report 20 Gb/s transmission of four-level pulse amplitude modulation (PAM) signal using a directly modulated tunable distributed Bragg reflector (DBR) laser. Transmission distance over 20 km was achieved without using optical amplifiers and optical dispersion compensation modules. A wavelength tuning range of 11.5 nm and a 3 dB bandwidth greater than 10 GHz over the entire wavelength tuning range were obtained.展开更多
Erbium fiber lasers of continuous mode outputs and of pulsed picosecond and sub-picosecond pulses train are reported. Compact all solid state passively modulated microchip lasers are also developed to the same degree.
Nonlinear pulse compression has been demonstrated by cross-phase modulation in a dispersion-shifted fiber. The output is obtained from filtering of the broadened optical spectrum and a pulse width reduction from 61 to...Nonlinear pulse compression has been demonstrated by cross-phase modulation in a dispersion-shifted fiber. The output is obtained from filtering of the broadened optical spectrum and a pulse width reduction from 61 to 28 ps is achieved.展开更多
A novel high-speed electro-optic (EO) polymer modulator based on long period gratings (LPG) is designed. Using the theory of multi-cladding optical waveguide, we achieved relationship between modulate voltage and LPG&...A novel high-speed electro-optic (EO) polymer modulator based on long period gratings (LPG) is designed. Using the theory of multi-cladding optical waveguide, we achieved relationship between modulate voltage and LPG's resonant wavelength.展开更多
Miniature optical fiber sensors with thin films as sensitive elements could open new fields for optical fiber sensor applications. Thin films work as sensitive elements and a transducer to get response and feedback fr...Miniature optical fiber sensors with thin films as sensitive elements could open new fields for optical fiber sensor applications. Thin films work as sensitive elements and a transducer to get response and feedback from environments, in which optical fibers act as a signal carrier. A novel Ag coated intensity modulated optical fiber sensor based on refractive index changes using IR and UV-Vis (UV-visible) light sources is proposed. The sensor with an IR light source has higher sensitivity compared to a UV-Vis source. When the refractive index is en- hanced to 1.38, the normalized intensity of IR and UV-Vis light diminishes to 0.2 and 0.8. respectively.展开更多
An all-fiber acousto-optic modulator(AOM), which features a compact structure and a low-driving voltage, is experimentally demonstrated for the active mode-locking of a fiber laser. The proposed AOM is based on the sh...An all-fiber acousto-optic modulator(AOM), which features a compact structure and a low-driving voltage, is experimentally demonstrated for the active mode-locking of a fiber laser. The proposed AOM is based on the short length of the cladding-etched fiber, the ends of which are fixed on a slide glass. On top of the cladding-etched fiber, a piezoelectric transducer was overlaid. A chemical wet-etching technique, which is based on a mixed solution of NH_4F and (NH_4)2SO_4, is used to reduce the fiber diameter down to ~25 μm, and the length of the etched section is only 0.5 cm. The fabricated device exhibited a modulation depth of 73.10% at an acoustic frequency of 918.9 kHz and a peak-to-peak electrical voltage of 10 V, while a laser beam was coupled at 1560 nm.By using the prepared AOM within an erbium-doped-fiber ring cavity, the mode-locked pulses with a temporalwidth of 2.66 ps were readily obtained at a repetition rate of 1.838 MHz.展开更多
基金Supported by the National Natural Science Foundation of China under Grant No 60977032the Program for Innovation Research of Science of Harbin Institute of Technology(PIRS-HIT)under Grant No T201407
文摘From Maxwell's equations and Post's formalism, a generalized chiral nonlinear Schr6dinger equation (CNLSE) is obtained for the nonlinear chiral fiber. This equation governs light transmission through a dispersive nonlinear chiral fiber with joint action of chirality in linear and nonlinear ways. The generalized CNLSE shows a modu- lation of chirality to the effect of attenuation and nonlinearity compared with the case for a conventional fiber. Simulations based on the split-step beam propagation method reveal the role of nonlinearity with cooperation to chirality playing in the pulse evolution. By adjusting its strength the role of chirality in forming solitons is demonstrated for a given circularly polarized component. The application of nonlinear optical rotation is also discussed in an all-optical switch.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11204328,61221064,61078037,11127901,11134010,and 61205208)the National Basic Research Program of China(Grant No.2011CB808101)the Natural Science Foundation of Shanghai,China(Grant No.13ZR1414800)
文摘We numerically study the pulse compression approaches based on atomic or molecular gases in a hollow-core fiber.From the perspective of self-phase modulation(SPM), we give the extensive study of the SPM influence on a probe pulse with molecular phase modulation(MPM) effect. By comparing the two compression methods, we summarize their advantages and drawbacks to obtain the few-cycle pulses with micro- or millijoule energies. It is also shown that the double pump-probe approach can be used as a tunable dual-color source by adjusting the time delay between pump and probe pulses to proper values.
文摘Currently,artificial-membrane lungs consist of thousands of hollow fiber membranes where blood flows around the fibers and gas flows inside the fibers,achieving diffusive gas exchange.At both ends of the fibers,the interspaces between the hollow fiber membranes and the plastic housing are filled with glue to separate the gas from the blood phase.During a uniaxial centrifugation process,the glue forms the“potting.”The shape of the cured potting is then determined by the centrifugation process,limiting design possibilities and leading to unfavorable stagnation zones associated with blood clotting.In this study,a new multiaxial centrifugation process was developed,expanding the possible shapes of the potting and allowing for completely new module designs with potentially superior blood flow guidance within the potting margins.Two-phase simulations of the process in conceptual artificial lungs were performed to explore the possibilities of a biaxial centrifugation process and determine suitable parameter sets.A corresponding biaxial centrifugation setup was built to prove feasibility and experimentally validate four conceptual designs,resulting in good agreement with the simulations.In summary,this study shows the feasibility of a multiaxial centrifugation process allowing greater variety in potting shapes,eliminating inefficient stagnation zones and more favorable blood flow conditions in artificial lungs.
基金supported by the China Postdoctoral Science Foundation(No.20060400230)the Foundation for Innovation Talents by the Technology Ministry of Harbin(No.2006RFQXG025)
文摘We theoretically analyze and experimentally demonstrate a method of generating equal-amplitude optical comb exploiting multi-frequency phase modulation. The theoretical analysis shows that 4n-1 equalamplitude spectral lines can be obtained when the modulation signal comprises n frequency components including the fundamental frequency and the odd harmonic frequencies, and 2n+1 equal-amplitude spectral lines can be obtained when the modulation signal comprises n frequency components including the fundamental frequency and the even harmonic frequencies. Then, we numerically simulate the spectra of 5, 7, 9, and 11 equal-amplitude spectral lines, respectively, which are also obtained in experiments with frequency separation of 30 MHz and flatness of better than 0.3 dB.
文摘Based on the high-speed development of the fiber laser in recent years, the development of researching 915 nm semiconductor laser as main pumping sources of the fiber laser is at a high speed. Because the beam quality of the laser diode is very poor, the 915 nm laser diode is generally based on optical fiber coupling module to output the laser. Using the beam-shaping and fiber-coupling technology to improve the quality of output beam light, we present a kind of high-power and high-brightness semiconductor laser module, which can output 13.22 W through the optical fiber. Based on 915 nm GaAs semiconductor laser diode which has output power of 13.91 W, we describe a thoroughly detailed procedure for reshaping the beam output from the semiconductor laser diode and coupling the beam into the optical fiber of which the core diameter is 105 μm and the numerical aperture is 0.18. We get 13.22 W from the output fiber of the module at 14.5 A, the coupling efficiency of the whole module is 95.03% and the brightness is 1.5 MW/cm2-str. The output power of the single chip semiconductor laser module achieves the advanced level in the domestic use.
基金supported by the National Key R&D Program of China (No.2018YFB1801003)the National Natural Science Foundation of China (Nos.61525501 and 61827817)+1 种基金the Beijing Natural Science Foundation (No.4192022)the Project of Shandong Province Higher Educational Science and Technology Program (No.J17KA089)。
文摘A tunable frequency-multiplying optoelectronic oscillator(OEO) based on a dual-parallel Mach-Zehnder modulator(DPMZM) is proposed and experimentally demonstrated. In the proposed system, the tunable fundamental microware signal is generated by a tunable optoelectronic oscillator incorporating a phase-shifted fiber Bragg grating(PS-FBG). By adjusting the DC bias of the DPMZM, the frequency-doubled microwave signal with a tunable frequency range from 11 GHz to 20 GHz and the frequency-quadrupled microwave signal with a tunable frequency range from 22.5 GHz to 26 GHz are generated. The phase noises of the fundamental, frequency-doubled and frequency-quadrupled signals at 10 k Hz offset frequency are-105.9 d Bc/Hz,-103.3 d Bc/Hz and-86.2 d Bc/Hz, respectively.
基金supported by the National Key Research and Development Program of China(Nos.2016YFB0402301 and 2017YFF0206103)the National Natural Science Foundation of China(Nos.61320106013,61635010,61474112,61574137,and 61504170)
文摘We report 20 Gb/s transmission of four-level pulse amplitude modulation (PAM) signal using a directly modulated tunable distributed Bragg reflector (DBR) laser. Transmission distance over 20 km was achieved without using optical amplifiers and optical dispersion compensation modules. A wavelength tuning range of 11.5 nm and a 3 dB bandwidth greater than 10 GHz over the entire wavelength tuning range were obtained.
文摘Erbium fiber lasers of continuous mode outputs and of pulsed picosecond and sub-picosecond pulses train are reported. Compact all solid state passively modulated microchip lasers are also developed to the same degree.
文摘Nonlinear pulse compression has been demonstrated by cross-phase modulation in a dispersion-shifted fiber. The output is obtained from filtering of the broadened optical spectrum and a pulse width reduction from 61 to 28 ps is achieved.
文摘A novel high-speed electro-optic (EO) polymer modulator based on long period gratings (LPG) is designed. Using the theory of multi-cladding optical waveguide, we achieved relationship between modulate voltage and LPG's resonant wavelength.
基金supported by the Universiti Teknologi Malaysia,AMTEC(No.R.J130000.7609.4C112)the Frontier Material Research Alliance
文摘Miniature optical fiber sensors with thin films as sensitive elements could open new fields for optical fiber sensor applications. Thin films work as sensitive elements and a transducer to get response and feedback from environments, in which optical fibers act as a signal carrier. A novel Ag coated intensity modulated optical fiber sensor based on refractive index changes using IR and UV-Vis (UV-visible) light sources is proposed. The sensor with an IR light source has higher sensitivity compared to a UV-Vis source. When the refractive index is en- hanced to 1.38, the normalized intensity of IR and UV-Vis light diminishes to 0.2 and 0.8. respectively.
基金National Research Foundation of Korea(NRF)(2015R1A2A2A04006979,2015R1A2A2A11000907)Institute for Information and Communications Technology Promotion(IITP-2017-2015-0-00385)
文摘An all-fiber acousto-optic modulator(AOM), which features a compact structure and a low-driving voltage, is experimentally demonstrated for the active mode-locking of a fiber laser. The proposed AOM is based on the short length of the cladding-etched fiber, the ends of which are fixed on a slide glass. On top of the cladding-etched fiber, a piezoelectric transducer was overlaid. A chemical wet-etching technique, which is based on a mixed solution of NH_4F and (NH_4)2SO_4, is used to reduce the fiber diameter down to ~25 μm, and the length of the etched section is only 0.5 cm. The fabricated device exhibited a modulation depth of 73.10% at an acoustic frequency of 918.9 kHz and a peak-to-peak electrical voltage of 10 V, while a laser beam was coupled at 1560 nm.By using the prepared AOM within an erbium-doped-fiber ring cavity, the mode-locked pulses with a temporalwidth of 2.66 ps were readily obtained at a repetition rate of 1.838 MHz.