Evolution mechanism of optical fiber strain induced by multi-fracture growth during fracturing in horizontal wells

A forward model for optical fiber strain was established based on a planar 3D multi-fracture model. Then the forward method calculating distributed fiber strain induced by multi-fracture growth was proposed. Based on this method, fiber strain evolution during fracturing of the horizontal well was numerically simulated. Fiber strain evolution induced by fracture growth can be divided into three stages: strain increasing, shrinkage convergence, and straight-line convergence, whereas the evolution of fiber strain rate has four stages: strain rate increasing, shrinkage convergence, straight-line convergence, and strain rate reversal after pumping stops. Fiber strain does not flip after pumping stop, while the strain rate flips after pumping stop so that strain rate can reflect injection dynamics. The time when the fracture extends to the fiber and inter-well pressure channeling can be identified by the straight-line convergence band of distributed fiber strain or strain rate, and the non-uniform growth of multiple fractures can be evaluated by using the instants of fractures reaching the fiber monitoring well.When the horizontal section of the fiber monitoring well is within the height range of a hydraulic fracture, the instant of the fracture reaching the fiber can be identified;otherwise, the converging band is not apparent. In multi-stage fracturing, under the influence of stress shadow from previous fracturing stages, the tensile region of fiber strain may not appear, but the fiber strain rate can effectively show the fracture growth behavior in each stage. The evolution law of fiber strain rate in single-stage fracturing can be applied to multi-stage fracturing.

High sensitive fiber strain sensor using suspended-core fibers

A novel fiber strain sensor is proposed, based on the two-mode interference of a suspended-core fiber. A fullvectorial finite difference mode solver is employed as the numerical tool for characterizing the proposed strain sensor. The numerical results show that the proposed strain sensor has an estimated sensitivity of 0.05 rad/（m-με）, higher than that of the strain sensors using conventional multimode fibers, while the temperature sensitivity of the proposed sensor is relatively low.

DETERMINATION OF INTERNAL STRAIN IN 3-D BRAIDED COMPOSITES USING OPTIC FIBER STRAIN SENSORS

A reliable understanding of the properties of 3-D braided composites is of primary importance for proper utilization of these materials. A new method is introduced to study the mechanical performance of braided composite materials using embedded optic fiber sensors. Experimental research is performed to devise a method of incorporating optic fibers into a 3-D braided composite structure. The efficacy of this new testing method is evaluated on two counts. First, the optical performance of optic fibers is studied before and after incorporated into 3-D braided composites, as well as after completion of the manufacturing process for 3-D braided composites, to validate the ability of the optic fiber to survive the manufacturing process. On the other hand, the influence of incorporated optic fiber on the original braided composite is also researched by tension and compression experiments. Second, two kinds of optic fiber sensors are co-embedded into 3-D braided composites to evaluate their respective ability to measure the internal strain. Experimental results show that multiple optic fiber sensors can be co-braided into 3-D braided composites to determine their internal strain which is difficult to be fulfilled by other current existing methods.

Robust Fiber Strain Sensor by Designing Coaxial Coiling Structure with Mutual Inductance Effect

Fiber strain sensors with robust sensing performance are indispensable for human-machine interactions in the electronic textiles.However,current fiber strain sensors are confronted with the challenges of unavoidable deterioration of functional sensing components during wearable and extreme environments,resulting in unsatisfactory stability and durability.Here,we present a robust fiber strain sensor based on the mutual inductance effect.The sensor is assembled by designing coaxial helical coils around an elastic polyurethane fiber.When stretching the fiber sensor,the strain is detected by recording the voltage changes in the helical coils due to the variation in magnetic flux.The resultant fiber strain sensor shows high linearity(with a linear regression coefficient of 0.99)at a large strain of 100%,and can withstand various extreme environmental conditions,such as high/low temperatures(from-30℃to 160℃),and severe deformations,such as twisting and pressing(with a pressure of 500 N/cm).The long-term cyclic stability of our fiber strain sensor(100,000 cycles at a strain of 100%)is superior to that of most reported flexible resistive and capacitive strain sensors.Finally,the mass-produced fiber strain sensors are woven into a smart textile system to accurately capture gestures.

Deformation and failure characteristics of sandstone under uniaxial compression using distributed fiber optic strain sensing

This paper investigates the deformation and fracture propagation of sandstone specimen under uniaxial compression using the distributed fiber optic strain sensing(DFOSS)technology.It shows that the DFOSS-based circumferential strains are in agreement with the data monitored with the traditional strain gage.The DFOSS successfully scans the full-field view of axial and circumferential strains on the specimen surface.The spatiotemporal strain measurement based on DFOSS manifests crack closure and elastoplastic deformation,detects initialization of microcrack nucleation,and identifies strain localization within the specimen.The DFOSS well observes the effects of rock heterogeneity on rock deformation.The advantage of DFOSS-based strain acquisition includes the high spatiotemporal resolution of signals and the ability of full-surface strain scanning.The introduction to the DFOSS technology yields a better understanding of the rock damage process under uniaxial compression.

Strain measurement of fiber optic sensor surface bonding on host material

Fiber optic sensor has been widely used as a structural health monitoring device by either embedding into or surface bonding onto the structures. The strain of optic fiber induced by the host material is strongly dependent on the bonding characteristics which include the protective coating, adhesive layer and the length of bonding. The strains between the fiber optics and host structure are not exact the same. The existence of the protective coating and adhesive layer would affect the strain measured by the surface bonding optic sensor. The analytical expression of the strain in the optic fiber induced by the host material was presented. The results were validated by the finite element method. The theoretical predictions reveal that the strain in the optical fiber is lower than the strain of host material. Parametric study shows that a long bonding length and high modulus of protective coating would increase the percentage of strain transferring into the optical fiber. Experiments were conducted by using Mach-Zehnder interferometer to measure the strain of the surface bonding optic fiber induced by the host structure. Good agreements were observed in comparison with the experimental results and theoretical predictions.

STRAIN REGULARITY IN REINFORCERS OF SHORT-FIBER/ WHISKER REINFORCED COMPOSITE AND ITS APPLICATION

Based on the study of strain distribution in short-fiber/whisker reinforced metal matrix composites, a deformation characteristic parameter λ is defined as the ratio of the root-mean-square strain of reinforcers to the macro-linear strain along the same direction. Quantitative relation between λ and microstructure parameters of the composite is obtained. As an example of applying and verifying λ, the stress-strain curve of ［AlBO］w/Al composite under tensile loading is predicted and favorably compared with experiments. By using λ, the stiffness modulus of the composite with arbitrary reinforcer orientation under any loading condition is predicted from the microstructure parameters of material.

Irradiation effect on strain sensitivity coefficient of strain sensing fiber Bragg gratings

The effect of irradiation on the strain sensitivity coefficient of strain sensing fiber Bragg gratings （FBGs） has been investigated through experiments. FBGs were fabricated in single mode fibers with 3 tool% Ge-concentration in the core and with a H2-1oading treatment. In experiments, the FBGs were subjected to y-radiation exposures using a Co6~ source at a dose-rate of 25 Gy/min up to a total dose of 10.5 kGy. The GeO defect in fiber absorbs photons to form a GeE＇ defect; the interaction with H2 is a probable reason for the y-radiation sensitivity of gratings written in hydrogen loaded fibres, The effect mechanism of radiation on the strain sensitivity coefficient is similar to that of radiation on the temperature sensitivity coefficient. Radiation affects the effective index neff, which results in the change of the thermo-optic coefficient and the strain-optic coefficient. Irradiation can change the strain sensitivity coefficient of FBGs by 1.48%-2.71%, as well as changing the Bragg wavelength shift （BWS） by 22 pm-25 pm under a total dose of 10.5 kGy. Our research demonstrates that the effect of irradiation on the strain sensitivity coefficient of FBG is small and that strain sensing FBGs can work well in the radiation environment.

Tensile Properties of Fiber Materials under Different Strain Rates

The quasi-static and dynamic tensile tests of aramid and high strength PVA fiber bundles are carried out under a wider range of strain rate by use of MTS (Materials Testing System) and bar-bar tensile impact apparatus. The influences of strain rate on mechanical properties of aramid and high strength polyvinyl alcohol fibers are studied. Micro failure mechanisms of fibers at different strain rates are examined by means of SEM.

A Dual-Mode Bow Tie Optical Fiber Sensor for Measurement of Axial Strain

An optical fiber strain sensor utilizing the mode-mode interference of LP01x, and LPJ11x modes in bow tie optical fibers is described. The heterodyne interference caused by frequency modulation of laser diode (LD) with ramp injection current is used to realize the detection of linear phase. Experimental results show a resolution of about 2% of one fringe corresponding to a strain of 2.9m.

Measurement of Temperature and Residual Strain during Fatigue of a CFRP Composite Using Fiber Bragg Grating Sensors

Fatigue behaviour has important implications for engineering composite structures in sectors ranging from automotive to aerospace. Optical sensing technology displays excellent performance in these fields for monitoring. In this paper, temperature and residual strain during fatigue of a carbon fiber reinforced polymer（CFRP） are investigated. Four autoclaved CFRP beam specimens, with fiber Bragg grating（FBG） sensors and thermocouples embedded at selected locations, are subjected to three-point bending cyclic loading on the BOSE testing machine for fatigue testing. Thennocouples are used to measure the temperature while FBGs can sense the temperature and strain as well. Seven tests in total are conducted at different frequencies, and each test lasts for several days. From the experimental results, transient steep peaks of temperature increases （up to 2.3℃） are discovered at the beginning of the load. The following constant temperature increments are around 1.0℃, which is not relevant to frequencies from 0.1 Hz to 20 Hz and suspected due to fatigue. Residual strains of 1×10^-5-2×10^-5 during fatigue, fading away rapidly when unloading, are also reported. Embedded FBGs here are validated to sense temperature and strains in composite structures, which demonstrates promising potentials in structure monitoring fields. CFRP are verified to have an excellent performance during fatigue with low temperature increase and residual strain.

Fiber Bragg Grating Strain Rosette

In this paper a Fiber Bragg Grating (FBG) Strain Rosette is designed, developed and tested. Traditional FBGs measure strain in only one direction. However, in-plane strain at a point consists of two normal strains and one shear strain. Hence a FBG strain rosette needs to be designed. The sensing principle of FBGs as a strain and temperature sensor and fundamental principles of strain transformation and strain gage rosettes are discussed.FBG strain rosettes are fabricated and embedded in two materials namely, Silicon Gel RTV 146-9 and Glass Fiber Composite Laminates. Experiments were conducted on the FBG strain rosette structures that were embedded in Silicon Gel (RTV 146-9). Initial findings from the experiments as well as preferred embedding material are presented.

Structure Damage Identification via Fiber Grating Strain Sensing Array Detecting and Wavelet Analysis

The measuring method of structure damage during vibrating has been developed by applying simple supported beam as object of study, fiber Bragg grating strain sensing array as the measuring method, and wavelet package analysis as signal extracting tools. The damage data of simple supported beam at vibrating state has been collected. The damage characteristic indexes have been extracted based on analyzing and handling the damage data with wavelet analysis. The experiment shows that fiber Bragg grating strain sensing array can sensitively measure the experimental data of simple supported beam at vibrating state. The fiber Bragg grating strain sensing array measuring is a new method in dynamic measurement.

Fiber Bragg Grating Strain Sensing Detecting Multi-Crack Damages under Vibrating Status

The multi-crack damages modal of simple supported beam has been build, at the vibrating status, the multi-damage detecting method of simple supported beam measured by fiber Bragg grating strain sensing array has been studied. From 0 hz to 200 hz, using exciter vibrating simple supported beam, with different damages, resonant frequency of simple supported beam has changed. So, when the damage appears in simple supported beam, the local rigidity will decrease, the resonant frequency of simple supported beam will be affected, the damage status of simple supported beam have been determined by this. The experimental result indicates that the resonant frequency of simple supported beam has changed when there is no damage, one damage, two damages, three damages on simple supported beam. According to this, the fiber Bragg grating strain sensing array can detect multi-crack damage of simple supported beam under vibrating status.

Charactersitics of Stress-strain Curve of High Strength Steel Fiber Reinforced Concrete under Uniaxial Tension

A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete （SFRC） under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.

Analysis of Dynamic Tensile Process of Fiber Reinforced Concrete by Acoustic Emission Technique

The fiber reinforced concrete has good dynamic mechanical properties. But corresponding research lacks the dynamic damage characteristics of the polypropylene fiber（fiber of low elastic modulus） and steel fiber（fiber of high elastic modulus） reinforced concrete under medium strain rate（10-6 s-1-10-4 s-1）. In order to study the effect of strain rate on the damage characteristics of fiber reinforced concrete during the full curve damage process, the real time dynamic acoustic emission（AE） technique was applied to monitor the damage process of fiber reinforced concrete at three strain rates. The AE wavelet energy spectrum in ca8 frequency band and average AE peak frequency at three strain rates were analyzed. With the accumulation of damage, the AE wavelet energy spectrum in ca8 frequency band increased first and then decreased, and the average AE peak frequency increased gradually. With the increase of strain rate, the AE wavelet energy spectrum in ca8 frequency band and average AE peak frequency decreased gradually. The polypropylene fiber content has more obvious effect on the Dynamic increase factor（DIF） of the peak stress than the steel fiber content. The theoretical basis was provided for the monitoring of dynamic damage of fiber reinforced concrete based on the AE technique.

Application of Tube-Packaged FBG Strain Sensor in Vibration Experi ment of Submarine Pipeline Model

Optical fiber sensors have received increasing attention in the fields of aeronautic and civil engineering for their superior ability to stand explosion, immunity to electromagnetic interference and high accuracy, especially fit for measureroent applications in harsh environment. In this study, a novel FBG （fiber Bragg grating） strain sensor, which is packaged in a 1.2 mm stainless steel tube with epoxy resin, is developed. Experiments are conducted on the universal material testing machine to calibrate its strain transferring characteristics. The sensor has the advantages of small size, high precision and flexible use, and exhibits promising potentials. Five tube-packaged strain FBG sensors have been applied to the vibration experiment of a submarine pipeline model. The strain measttred with the FBG sensor agrees well with that measttred with the electric resistance strain sensor.

Continuous Deformation Monitoring by Polymermatrix Carbon Fiber Sensitive Layer

Composite made of short-cut carbon fiber mat and vinyl ester resin was observed to be an effective sensor for tensile strain up to 6 000με. Based on its strain sensitivity, a skin-like sensitive layer which can continuously cover the structural surface to sense strain in large area was developed. The sensitive layer was applied to continuously monitor the deformation of a simply supported beam. The result indicates that the fractional change in electrical resistance of the sensitive layer reversibly reflects the beam deformation in each section and describes the distribution of the average strain of the beam. The effect of temperature change on the monitoring was studied by monitoring tests conducted at different temperatures ranging from 20 to 80 ℃, which reveals temperature sensitivity in the sensitive layer and the temperature dependence of the piezoresistive behavior when the temperature exceeds 50 ℃. By the application of differential conaection principle, a method for temperature compensation was established and the gauge factor for the monitoring was dramatically increased. This method was verified experimentally.

High-cycle Fatigue Life Extension of Glass Fiber/Polymer Composites with Carbon Nanotubes

The present work shows that the addition of small volume fractions of multi-walled carbon nanotubes （CNTs） to the matrix results in a significant increase in the high-cycle fatigue life. It is proposed that carbon nanotubes tend to inhibit the formation of large cracks by nucleating nano-scale damage zones. In addition, the contribution to energy absorption from the fracture of nanotubes bridging across nano-scale cracks and from nanotube pull-out from the matrix are mechanisms that can improve the fatigue life. An energy-based model was proposed to estimate the additional strain energy absorbed in fatigue. The distributed nanotubes in the matrix appear to both distribute damage as well as inhibit damage propagation resulting in an overall improvement in the fatigue strength of glass fiber composites.