Efficiency characterization of ceramic filtering materials used for drinking water treatment

For ceramic filtering materials, their adsorption capacities, purification efficiencies to remove organic compounds from drinking water, and correlation between adsorption capacities and pore structures were tested and analyzed. The results show that correlation coefficient between the specific surface area and the adsorptive amount of iodine molecule is 0.99; correlation coefficient between the pore volume and the adsorptive value of tannin molecule is 0.92, and correlation coefficient between the most probable diameter and the adsorption parameter is 1.0. A new method of morphology characterization for ceramic filtering materials was developed, which offered a sort of standard for the evaluation on water purification efficiencies and selection of ceramic filtering materials.

Clean Steel Technologies Based on Interactions of Refractory Filtering Materials with Steel Melt

New carbon bonded filters with “active and reactive coatings ” for higher filtration efficiency of alumina based inclusions as well as nano-engineered filters with nano-scaled additives are explored with the aid of impingement tests and are evaluated according to their cold crushing strengths at room temperature. The combination of carbon nanotubes and alumina nanosheets additives leads to in situ formation of Al3 CON. Both the nanoscaled additives as well as the extra alumina “active”coating lead to improved mechanical performance of the carbon bonded filters and open the horizon for filter macrostructures with higher filtration capacities in means of bigger dimensions. In a further step MWCNT（ multi walled carbon nanotubes） in combination with a synthetic pitch have been used as a functional coating on the surface of alumina carbon bonded filters. These filters have then been evaluated also with uncoated filters in a special casting simulator and the interactions between steel and filtering material have been investigated.

An Influencing Factor - Water-Filter Ratio on Heat Resistance of Condensate Polishing Filter Material in Water

In air-cooled condenser, high temperature condensing water m summer which approaching and exceed 60＊ C, which may result in filter materials degradation and release impurities. This paper discusses an influencing factor, water-filter ratio （soaking solution and filter quality ratio）, on leachable dissolution rate and filter material degradation rate m high temperature water. The UV absorption at 254nm （A254） and the exchange capacity ware measured after heat test as composite indicators. In addition, the Wends of A254 variation with heating time were measured in different water-filter ratio. The stability is probably due to the effect of water-filter ratio. This has been further borne out that, water-filter ratio increases, leachable concentration decreases exponentially and tends to a fLxed value.

Preparation and Physical Properties of Ceramsite Filter Media for Water Treatment Obtained from Municipal Solid Wastes

Sludge,solid waste of sewage treatment plants,poses a threat as a secondary pollution if it is not handled properly.In this study,artifical ceramsite filter material(ACFM)for water treatment,was obtained from sludge by high-temperature sintering process,and then it’s physical properties,leaching toxicity and sintering mechanisms were investigated.The results showed that the preferred conditions for the preparation of ACFM were that the mass ratio of sludge,river sediment and fly ash was 5∶4∶1,preheated at 400℃for 20 min and sintered at 1 150℃for 5 min.After the optimal sintering conditions treatment,the physical properties of the rate of breaking and wear,solubility in hydrochloric acid,silt carrying capacity,void fraction and Brunauer-Emmett-Teller(BET)specific surface area of ACFM were 0.2%,0.01%,0.2%,71.1%and 0.75×104cm2/g,respectively.The results confirmed that the ACFM’s physical properties were totally aligned to the requirements of China’s industry standard(CJ/T 299—2008).The leaching toxicity results indicated that the leaching contents of heavy metals,such as Cr,Zn and Cu,were much lower than the thresholds of China’s national standards(GB 5085.3—2007 and GB 8978—1996).

Improving oxidation resistance of porous FeAl-based intermetallics with high boron/yttrium alloying

The coalloying with high contents of chromium(Cr),boron(B)and yttrium(Y)for porous B2-structured FeAl intermetallics fabricated through reactive synthesis was conducted.The oxidation behaviors of porous FeAl-based materials were investigated by evaluating the pore-structure evolution,oxidation kinetics and oxide-scale configuration.The results show that with the coalloying of high contents of Cr,B and Y,the oxidation mass gains of porous FeAl materials at 600−800℃ are significantly reduced.The combination of B enriched on the surface of oxide scales and Y located at the scale−metal interface promotes the formation of thin protective nodularα-Al_(2)O_(3) oxide scales.It is indicated that introducing relatively high contents of reactive elements such as B and Y can benefit the selective growth ofα-Al_(2)O_(3) scales at relatively low temperatures without pre-treatment.

Tunable wavelength filters using polymer long-period waveguide gratings based on metal-cladding directly defined technique

In this work, long-period waveguide grating-based tunable wavelength filters using organic–inorganic grafting poly（methyl methacrylate）（PMMA） materials are designed and fabricated by metal-cladding directly defined technique.The thermal stabilities and optical properties of the organic–inorganic grafting PMMA core materials are analyzed. Structures and performance parameters of the waveguide gratings and self-electrode heaters are designed and simulated. The contrast of the filter is about 15 d B and the resonant wavelength can be tuned by different electric powers applied to the metal-cladding self-electrode heaters. The temperature sensitivity is 3.5 nm/℃ and the switching time is about 1 ms. The technique is very suitable for realizing the optoelectronic integrated wavelength-division-multiplexing systems.

Monte Carlo simulations for 20 MV X-ray spectrum reconstruction of a linear induction accelerator

To study the spectrum reconstruction of the 20 MV X-ray generated by the Dragon-I linear induction accelerator, the Monte Carlo method is applied to simulate the attenuations of the X-ray in the attenuators of different thicknesses and thus provide the transmission data. As is known, the spectrum estimation from transmission data is an ill-conditioned problem. The method based on iterative perturbations is employed to derive the X-ray spectra, where initial guesses are used to start the process. This algorithm takes into account not only the minimization of the differences between the measured and the calculated transmissions but also the smoothness feature of the spectrum function. In this work, various filter materials are put to use as the attenuator, and the condition for an accurate and robust solution of the X-ray spectrum calculation is demonstrated. The influences of the scattering photons within different intervals of emergence angle on the X-ray spectrum reconstruction are also analyzed.