Improving creep strength of the fine-grained heat-affected zone of novel 9Cr martensitic heat-resistant steel via modified thermo-mechanical treatment

The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power plants.In this work,the traditional thermo-mechanical treatment was modified via the replacement of hot-rolling with cold rolling,i.e.,normalizing,cold rolling,and tempering (NCT),which was developed to improve the creep strength of the FGHAZ in G115 steel weldments.The NCT treatment effectively promoted the dissolution of preformed M_(23)C_(6)particles and relieved the boundary segregation of C and Cr during welding thermal cycling,which accelerated the dispersed reprecipitation of M_(23)C_(6) particles within the fresh reaustenitized grains during post-weld heat treatment.In addition,the precipitation of Cu-rich phases and MX particles was promoted evidently due to the deformation-induced dislocations.As a result,the interacting actions between precipitates,dislocations,and boundaries during creep were reinforced considerably.Following this strategy,the creep rupture life of the FGHAZ in G115 steel weldments can be prolonged by 18.6%,which can further push the application of G115 steel in USC power plants.

A new solution to estimate the time delay on the topographic site using time domain 3D boundary element method

This study focuses on investigating spatial variation of ground motion that has great influence on the dynamic behavior of the large structures located on the surface topography.One of the most effective parameters on the spatial variation of ground motion is the difference between the arrival time of seismic waves in different points located on the abutments.In this research,a three-dimensional model of the Pacoima Dam site is prepared.The time domain 3 D boundary element method is used to apply non-uniform excitation at the dam supports.This model is subjected to vertically propagating incident SH and P waves.The time delay can be characterized by calculating the value of the time delay for which the cross-correlation between two records is maximized.Finally,to obtain the time delay in a topographic site,a function considering effective parameters such as the height from the canyon base,wave velocity and predominant frequency,is presented.Furthermore,a code was developed for generating the spatially variation of seismic ground motions.The results show that the proposed functions have an acceptable accuracy in estimating the time delay to generate non-uniform ground motion.

Relationship between serum adhesion molecules, trace elements and delayed union of tibial and fibula fractures

Objective:To investigate the relationship between serum adhesion molecules, trace elements and delayed union of tibial and fibula fractures.Methods:A total of 46 patients with delayed union of tibial and fibula fractures in our hospital from May 2014 to June 2016 were selected as the observation group, 46 patients with normal healing of tibial and fibula fractures were selected as the control group, then the serum adhesion molecules and trace elements levels of two groups at forth, eighth and sixteenth week after the surgery were compared.Results:The serum dhesion molecules levels of observation group at forth, eighth and sixteenth week after the surgery were all higher than those of control group, the serum trace elements levels were all lower than those of control group, and the serum adhesion molecules levels of two groups at eighth week after the surgery were all higher than those at other time, the trace elements levels were all lower than those at other time (allP<0.05).Conclusions:The serum adhesion molecules and trace elements of patients with delayed union of tibial and fibula fractures show obviously abnormal state, so those indexes of those patients should be paid to more monitoring and improvement.

Fine-Grain Sleep Transistor Insertion for Leakage Reduction

A fine-grain sleep transistor insertion technique based on our simplified leakage current and delay models is proposed to reduce leakage current. The key idea is to model the leakage current reduction problem as a mixed-integer linear programming （MLP） problem in order to simultaneously place and size the sleep transistors optimally. Because of better circuit slack utilization, our experimental results show that the MLP model can save leakage by 79.75%, 93.56%, and 94.99% when the circuit slowdown is 0%, 3%, and 5%, respectively. The MLP model also achieves on average 74.79% less area penalty compared to the conventional fixed slowdown method when the circuit slowdown is 7%.

Introducing an effective coherence function to generate non-uniform ground motion on topographic site using time-domain boundary element method

In this study,a comprehensive parametric analysis was performed on non-uniform excitation of V-shaped topography using the boundary element method in time domain.For this purpose,wave scattering analysis was carried out on a topography subjected to the SV-wave for different predominant frequencies and shape ratios.Based on the numerical results,new coherence and time delay functions are proposed to generate non-uniform ground motion for topographic irregularities.The efficiency and accuracy of the proposed functions for real engineering problems are indicated by comparison with observations reported in previous literature.

Adsorption experiment of water-soluble rare earth elements in atmospheric depositions and implications for source tracing in South China

The distribution patterns of rare earth elements(REEs)in fine-grained materials in various depositions were often found to be similar to those of the aeolian sediments deposited in the Loess Plateau in North China and the fine-grained materials were suggested to be derived from wind-blown dust.However,increasing evidence indicated that the REEs in the water-soluble portion of atmospheric depositions also displayed similar patterns to those of aeolian sediments.In this study,water-soluble REEs in three atmospheric depositions collected from different climatic zones in China were adsorbed with two adsorbents with distinct adsorption capacity,glass powder,and co-precipitated iron hydroxide.The results showed that the REEs adsorbed by the two adsorbents displayed patterns similar to those of the original atmospheric depositions.The typical characteristics of the REE patterns of atmospheric deposition can be well reproduced in the adsorbed REEs.The higher the REE concentrations in the atmospheric depositions,or the higher adsorption efficiency of the adsorbents,the better reproducibility of the REEs patterns.The results suggest that the REEs of the fine-grained materials in various sediments,which have a high adsorption capacity,especially those deposited in South China,may come from the water-soluble REEs in atmospheric deposition,and may not be appropriate tracers of wind-blown dust from North China.

Analysis of Pulverized Coal by Laser-Induced Breakdown Spectroscopy

Laser-induced breakdown spectroscopy （LIBS） has been used to detect atomic species in various enviromnents. The quantitative analysis （C, H, O, N and S） of representative coal samples are being carried out with LIBS, and the effects of particle size are analyzed. A powerful pulse Nd：YAG laser is focused on the coal sample at atmosphere pressure, and the emission spectra from laser-induced plasmas are measured by time-resolved spectroscopy, and the intensity of analyzed spectral lines is obtained through observing the laser plasma with a delay time of 0.4 #s. The experimental results show that the slope of calibration curve is nearly 1 when the concentration of the analyzed element is relatively low, and the slope of curve is nearly 0.5 when the concentration of C is higher than other elements. In addition, using the calibration-free model without self-absorption effect, the results show that the decreasing of particle size leads to an increase of the plasma temperature.

Ultrasonic beam steering using Neumann boundary condition in multiplysics

The traditional one-dimensional ultrasonic beam steering has time delay and is thus a complicated problem. A numerical model of ultrasonic beam steering using Neumann boundary condition in multiplysics is presented in the present paper. This model is based on the discrete wave number method that has been proved theoretically to satisfy the continuous conditions. The propagating angle of novel model is a function of the distance instead of the time domain. The propagating wave fronts at desired angles are simulated with the single line sources for plane wave. The result indicates that any beam angle can be steered by discrete line elements resources without any time delay.

Clock generator and OOK modulator for RFID application

The clock generator and OOK modulator for RFID (Radio Frequency Identification) presented in this paper consist of a current source and delay elements. The simple constant-gm structure is adopted in the current source design and the current consumption of the current source is only about 2 μA. The delay elements, the clock generator and OOK modulator are introduced in detail in the paper. The designed circuits are fabricated by 0.6 μm CMOS process. The area of the core circuit is only about 400 μm×80 μm. The delay time of all three samples is in the range of 9 μs to 21 μs when the supply voltage varies from 2 V to 4 V. As the measured results satisfy the system requirements, these circuit structures are suitable for RFID application.

An experimental and numerical approach-characterisation of power cartridge for water-jet application

Power Cartridges are pyrotechnic devices where hot combustion gases utilized to do mechanical work for disruption of suspected Improvised Explosive Devices(IEDs). It plays a vital role either in destroying the suspicious object or making them non-functional by generating the gas pressure on burning of propellant against the water column inside the barrel, Present work is focused on characterisation,numerical solution such as deformation; strain; stress using FEM(Finite Element Method), design qualification, performance and evaluation of power cartridge for disruptor application. Experimental trials for pressure-time(P-t) measurement in closed vessel(CV), various electrical parameters like all fire current(AFC), no fire current(NFC) and ignition delay have been measured. Further, mechanical properties for brass material have been determined. An attempt has been made to characterise the power cartridge by FEM and carrying out the experiments for water-jet application.

A novel power-on-reset circuit for passive UHF RFID tag chip

A novel power-on-reset(POR) circuit with simple architecture, small values of capacitances, ultralower power consumption, and self-adjustable delay time of reset pulse for passive UHF RFID tags is presented in this paper. A proposed delay element was adopted for the features of small capacitances and wide power supply rise time range. An inverter was used as a two-inputs logic device to simplify the architecture of the circuit. The technology used for design and simulation is SMIC 0.18 μm RF. Simulation results show that the circuit functions well under different process corners with different power supply rise time, and is able to generate a POR signal after the power supply is briefly powered off. The static power consumption is less than 30 pA. Moreover, the circuit operates properly along with other modules of analog front-end.

On Approximation and Computation of Navier-Stokes Flow

We present an approximation method for the non-stationary nonlinear in- compressible Navier-Stokes equations in a cylindrical domain （0, T） x G, where G C ]R3 is a smoothly bounded domain. Our method is applicable to general three-dimensional flow without any symmetry restrictions and relies on existence, uniqueness and rep- resentation results from mathematical fluid dynamics. After a suitable time delay in the nonlinear convective term v. ~7v we obtain globally （in time） uniquely solvable equations, which - by using semi-implicit time differences - can be transformed into a finite number of Stokes-type boundary value problems. For the latter a boundary element method based on a corresponding hydrodynamical potential theory is carried out. The method is reported in short outlines ranging from approximation theory up to numerical test calculations.