Analysis of Direct Torque Control for Marine Five-Phase Induction Motor

Based on the principle of direct torque control,a DTC(Direct Torque Control)system with five-phase induction motor has been studied.Providing direct control of stator flux and electromagnetic torque by optimized voltage vector,five-phase induction motor enhances flexibility of the invert states selection by increasing the number of voltage vectors,resulting in more precise control of stator flux and electromagnetic torque.The model of DTC for five-phase induction motor is constructed on equations and the method of approximate circle of torque track is used to conduct the simulation analysis of the system.The simulation results demonstrate that the DTC for five-phase induction motor control has merits of little calculation compared with vector control,simple structure,fast response and greater dynamic performance.

A Stable Fuzzy-Based Computational Model and Control for Inductions Motors

In this paper,a stable and adaptive sliding mode control(SMC)method for induction motors is introduced.Determining the parameters of this system has been one of the existing challenges.To solve this challenge,a new self-tuning type-2 fuzzy neural network calculates and updates the control system parameters with a fast mechanism.According to the dynamic changes of the system,in addition to the parameters of the SMC,the parameters of the type-2 fuzzy neural network are also updated online.The conditions for guaranteeing the convergence and stability of the control system are provided.In the simulation part,in order to test the proposed method,several uncertain models and load torque have been applied.Also,the results have been compared to the SMC based on the type-1 fuzzy system,the traditional SMC,and the PI controller.The average RMSE in different scenarios,for type-2 fuzzy SMC,is 0.0311,for type-1 fuzzy SMC is 0.0497,for traditional SMC is 0.0778,and finally for PI controller is 0.0997.

Harmonics in the Squirrel Cage Induction Motor Analytic Calculation Part III: Influence on the Torque-speed Characteristic

The harmonics that appear in the squirrel cage asynchronous machine have been discussed in great detail in the literature for a long time. However, the systematization of the phenomenon is still pending, so we made an attempt to fill this gap in the previous parts of our study by elaborating formulas for calculation of parasitic torques. It was a general demand among those who work in this field towards the author to verify his formulas with measurements. In the literature, it seems,only one detailed, purposeful series of measurements has been published so far, the purpose of which was to investigate the effect of the number of rotor slots on the torque-speed characteristic curve of the machine. The main goal of this study is to verify the correctness of the formulas by comparing them with the referred series of measurements. Relying on this, the expected synchronous parasitic torques were developed for the frequently used rotor slot numbers-as a design guide for the engineer.Thus, together with our complete table for radial magnetic pull published in our previous work, the designer has all the principles, data and formulas available for the right number of rotor slots for his given machine and for the drive system. This brings this series of papers to an end.

Enhanced Fuzzy Logic Control Model and Sliding Mode Based on Field Oriented Control of Induction Motor

In the context of induction motor control, there are various control strategies used to separately control torque and flux. One common approach is known as Field-Oriented Control (FOC). This technique involves transforming the three-phase currents and voltages into a rotating reference frame, commonly referred to as the “dq” frame. In this frame, the torque/speed and flux components are decoupled, allowing for independent control, by doing so, the motor’s speed can be regulated accurately and maintain a constant flux which is crucial to ensure optimal motor performance and efficiency. The research focused on studying and simulating a field-oriented control system using fuzzy control techniques for an induction motor. The aim was to address the issue of parameter variations, particularly the change in rotor resistance during motor operation, which causes the control system to deviate from the desired direction. This deviation implies to an increase in the magnetic flux value, specifically the flux component on the q-axis. By employing fuzzy logic techniques to regulate flux vector’s components in the dq frame, this problem was successfully resolved, ensuring that the magnetic flux value remains within the nominal limits. To enhance the control system’s performance, response speed, and efficiency of the motor, sliding mode controllers were implemented to regulate the current in the inner loop. The simulation results demonstrated the proficiency of the proposed methodology.

Indirect Vector Control of Linear Induction Motors Using Space Vector Pulse Width Modulation

Vector control schemes have recently been used to drive linear induction motors(LIM)in high-performance applications.This trend promotes the development of precise and efficient control schemes for individual motors.This research aims to present a novel framework for speed and thrust force control of LIM using space vector pulse width modulation(SVPWM)inverters.The framework under consideration is developed in four stages.To begin,MATLAB Simulink was used to develop a detailed mathematical and electromechanical dynamicmodel.The research presents a modified SVPWM inverter control scheme.By tuning the proportional-integral(PI)controller with a transfer function,optimized values for the PI controller are derived.All the subsystems mentioned above are integrated to create a robust simulation of the LIM’s precise speed and thrust force control scheme.The reference speed values were chosen to evaluate the performance of the respective system,and the developed system’s response was verified using various data sets.For the low-speed range,a reference value of 10m/s is used,while a reference value of 100 m/s is used for the high-speed range.The speed output response indicates that themotor reached reference speed in amatter of seconds,as the delay time is between 8 and 10 s.The maximum amplitude of thrust achieved is less than 400N,demonstrating the controller’s capability to control a high-speed LIM with minimal thrust ripple.Due to the controlled speed range,the developed system is highly recommended for low-speed and high-speed and heavy-duty traction applications.

Harmonics in the Squirrel Cage Induction Motor,Analytic Calculation Part Ⅱ:Synchronous Parasitic Torques,Radial Magnetic Forces

The magnetic field generated in the air gap of the cage asynchronous machine and the harmonics of the magnetomotive forces creating that magnetic field,as well as the synchronous parasitic torques,radial magnetic forces have been discussed in great detail in the literature,but always separately,for a long time.However,systematization of the phenomenon still awaits.Therefore,it is worth summarizing the completeness of the phenomena in a single study–with a new approach at the same time-in order to reveal the relationships between them.The role of rotor slot number is emphasized much more than before.New formulas derived for both synchronous torques and radial magnetic forces are used for further investigation.It will be shown that both phenomena in subject must be treated together.Formulas will be provided to take into account attenuation.Design guide will be provided to avoid dangerous rotor slot numbers.It will be shown that the generation of synchronous torques and radial magnetic forces do not depend–in this new approach-on the slot combination,but on the rotor slot number itself.

Harmonics in the Squirrel Cage Induction Motor Analytic Calculation-Part Ⅰ: Differential Leakage, Attenuation, Asynchronous Parasitic Torques

The magnetic field generated in the air gap of the cage asynchronous machine and the harmonics of the magnetomotive forces creating that magnetic field, as well as the related differential leakage, attenuation, asynchronous parasitic torques have been discussed in great detail in the literature, but always separately, for a long time. However, systematization of the phenomenon still awaits. Therefore, it is worth summarizing the completeness of the phenomena in a single study – with a new approach at the same time-in order to reveal the relationships between them. The role of rotor slot number is emphasized much more than before. An existing, commonly used, but still impractical basic figure has been modified to more clearly demonstrate the response of the rotor for the harmonics of the stator. The need to treat differential leakage, asynchronous parasitic torques and attenuation together will be demonstrated: new formula for asynchronous parasitic torque is derived;the long-used characteristic curves for differential leakage and attenuation used separately so far was merged into one, correct curve in order to provide a correct design guide for the engineers.

Speed Identification of Speed Sensorless Linear Induction Motor Based on MRAS

In the linear induction motor control system,the optical grating speed transducer is susceptible to strong magnetic field interference.What's more,it may reduce motor integration and raise device costs.Therefore a speed identification method to replace grating speed transducer is studied in this article.This speed identification method for linear induction motor mainly adopts Model Reference Adaptive Method(Abbreviated as MRAS)and Popov Hyperstability Theory.The research content of this paper can be divided into four parts.First,the mathematical model of the motor based on the model reference adaptive system structure is deduced.Second,the adaptive law of the estimated speed is solved by Popov hyper-stability theory,which ensures the stability of the system.Third,the simulation model of the linear induction motor speed identification control system based on model reference adaptation is built in the MATLAB environment.Finally,the simulation test and analysis are carried out.The simulation results show that the speed identification control system can track the actual speed of the linear induction motor well in the no-load operation and the load operation,and the stability of the system is guaranteed in the full speed range.

Performance Analysis of Optimization Based FOC and DTC Methods for Three Phase Induction Motor

Three-phase induction motors are becoming increasingly utilized in industrialfield due to their better efficiency and simple manufacture.The speed control of an induction motor is essential in a variety of applications,but it is dif-ficult to control.This research analyses the three-phase induction motor’s perfor-mance usingfield-oriented control(FOC)and direct torque control(DTC)techniques.The major aim of this work is to provide a critical evaluation of devel-oping a simple speed controller for induction motors with improving the perfor-mance of Induction Motor(IM).For controlling a motor,different optimization approaches are accessible;in this research,a Fuzzy Logic Controller(FLC)with Fractional Order Darwinian Particle Swarm Optimization(FODPSO)algorithm is presented to control the induction motor.The FOC and DTC are controlled using FODPSO,and their performance is compared to the traditional FOC and DTC technique.Each scheme had its own simulation model,and the results were com-pared using hardware experimental and MATLAB-Simulink.In terms of time domain specifications and torque improvement,the proposed technique surpasses the existing method.

Improved Clamped Diode Based Z-Source Network for Three Phase Induction Motor

The 3Φinduction motor is a broadly used electric machine in industrial applications,which plays a vital role in industries because of having plenty of beneficial impacts like low cost and easiness but the problems like decrease in motor speed due to load,high consumption of current and high ripple occurrence of ripples have reduced its preferences.The ultimate objective of this study is to control change in motor speed due to load variations.An improved Trans Z Source Inverter(ΓZSI)with a clamping diode is employed to maintain constant input voltage,reduce ripples and voltage overshoot.To operate induction motor at rated speed,different controllers are used.The conventional Proportional-Inte-gral(PI)controller suffers from high settling time and maximum peak overshoot.To overcome these limitations,Fractional Order Proportional Integral Derivative(FOPID)controller optimized by Gray Wolf Optimization(GWO)technique is employed to provide better performance by eliminating maximum peak overshoot pro-blems.The proposed speed controller provides good dynamic response and controls the induction motor more effectively.The complete setup is implemented in MATLAB Simulation to verify the simulation results.The proposed approach provides optimal performance with high torque and speed along with less steady state error.

Controller Design for Induction and Brushless Motors Using Matlab with Digital Signal Processor (DSP)

The automation process is a very important pillar for Industry 4.0.One of the first steps is the control of motors to improve production efficiency and generate energy savings.In mass production industries,techniques such as digital signal processing(DSP)systems are implemented to control motors.These systems are efficient but very expensive for certain applications.From this arises the need for a controller capable of handling AC and DC motors that improves efficiency and maintains low energy consumption.This project presents the design of an adaptive control system for brushless AC induction and DC motors,which is functional to any type of plant in the industry.The design was possible by implementing Matlab software and tools such as digital signal processor(DSP)and Simulink.Through an extensive investigation of the state of the art,three models needed to represent the control system have been specified.The first model for the AC motor,the second for the DC motor and the third for the DSP control;this is done in this way so that the probability of failure is lower.Subsequently,these models have been programmed in Simulink,integrating the three main models into one.In this way,the design of a controller for use in AC induction motors,specifically squirrel cage and brushless DC motors,has been achieved.The final model represents a response time of 0.25 seconds,which is optimal for this type of application,where response times of 2e-3 to 3 seconds are expected.

An Intelligent Harmonic Synthesis Technique for Air-Gap Eccentricity Fault Diagnosis in Induction Motors

Induction motors （IMs） are commonly used in various industrial applications. To improve energy con- sumption efficiency, a reliable IM health condition moni- toring system is very useful to detect IM fault at its earliest stage to prevent operation degradation, and malfunction of IMs. An intelligent harmonic synthesis technique is pro- posed in this work to conduct incipient air-gap eccentricity fault detection in IMs. The fault harmonic series are syn- thesized to enhance fault features. Fault related local spectra are processed to derive fault indicators for IM air- gap eccentricity diagnosis. The effectiveness of the pro- posed harmonic synthesis technique is examined experi- mentally by IMs with static air-gap eccentricity and dynamic air-gap eccentricity states under different load conditions. Test results show that the developed harmonic synthesis technique can extract fault features effectively for initial IM air-gap eccentricity fault detection.

A novel induction motor control scheme using IDA-PBC

A new control scheme for induction motors is proposed in the present paper, applying the interconnection and damping assignment-passivity based control （IDA-PBC） method. The scheme is based exclusively on passivity based control, without restricting the input frequency as it is done in field oriented control （FOC）. A port-controlled Hamiltonian （PCH） model of the induction motor is deduced to make the interconnection and damping of energy explicit on the scheme. The proposed controller is validated under computational simulations and experimental tests using an inverter prototype.

Online Detection of Broken Rotor Bar Fault in Induction Motors by Combining Estimation of Signal Parameters via Min-norm Algorithm and Least Square Method

Current research in broken rotor bar （BRB） fault detection in induction motors is primarily focused on a high-frequency resolution analysis of the stator current. Compared with a discrete Fourier transformation, the parametric spectrum estimation technique has a higher frequency accuracy and resolution. However, the existing detection methods based on parametric spectrum estima- tion cannot realize online detection, owing to the large computational cost. To improve the efficiency of BRB fault detection, a new detection method based on the min-norm algorithm and least square estimation is proposed in this paper. First, the stator current is filtered using a band-pass filter and divided into short overlapped data windows. The min-norm algorithm is then applied to determine the fre- quencies of the fundamental and fault characteristic com- ponents with each overlapped data window. Next, based on the frequency values obtained, a model of the fault current signal is constructed. Subsequently, a linear least squares problem solved through singular value decomposition is designed to estimate the amplitudes and phases of the related components. Finally, the proposed method is applied to a simulated current and an actual motor, the results of which indicate that, not only parametric spectrum estimation technique.

Sensorless torque control scheme of induction motor for hybrid electric vehicle

In this paper, the sensorless torque robust tracking problem of the induction motor for hybrid electric vehicle （HEV） applications is addressed, Because motor parameter variations in HEV applications are larger than in industrial drive system, the conventional field-oriented control （FOC） provides poor performance. Therefore, a new robust PI-based extension of the FOC controller and a speed-flux observer based on sliding mode and Lyapunov theory are developed in order to improve the overall performance. Simulation results show that the proposed sensorless torque control scheme is robust with respect to motor parameter variations and loading disturbances. In addition, the operating flux of the motor is chosen optimally to minimize the consumption of electric energy, which results in a significant reduction in energy losses shown by simulations.

Linearizing Control of Induction Motor Based on Networked Control Systems

A new approach to speed control of induction motors is developed by introducing networked control systems （NCSs） into the induction motor driving system. The control strategy is to stabilize and track the rotor speed of the induction motor when the network time delay occurs in the transport medium of network data. First, a feedback linearization method is used to achieve input-output linearization and decoupling control of the induction motor driving system based on rotor flux model, and then the characteristic of network data is analyzed in terms of the inherent network time delay. A networked control model of an induction motor is established. The sufficient condition of asymptotic stability for the networked induction motor driving system is given, and the state feedback controller is obtained by solving the linear matrix inequalities （LMIs）. Simulation results verify the efficiency of the proposed scheme.

Broken Rotor Bar Fault Detection of Induction Motors Using a Joint Algorithm of Trust Region and Modified Bare-bones Particle Swarm Optimization

A precise detection of the fault feature parameter of motor current is a new research hotspot in the broken rotor bar(BRB) fault diagnosis of induction motors. Discrete Fourier transform(DFT) is the most popular technique in this field, owing to low computation and easy realization. However, its accuracy is often limited by the data window length, spectral leakage, fence e ect, etc. Therefore, a new detection method based on a global optimization algorithm is proposed. First, a BRB fault current model and a residual error function are designed to transform the fault parameter detection problem into a nonlinear least-square problem. Because this optimization problem has a great number of local optima and needs to be resolved rapidly and accurately, a joint algorithm(called TR-MBPSO) based on a modified bare-bones particle swarm optimization(BPSO) and trust region(TR) is subsequently proposed. In the TR-MBPSO, a reinitialization strategy of inactive particle is introduced to the BPSO to enhance the swarm diversity and global search ability. Meanwhile, the TR is combined with the modified BPSO to improve convergence speed and accuracy. It also includes a global convergence analysis, whose result proves that the TR-MBPSO can converge to the global optimum with the probability of 1. Both simulations and experiments are conducted, and the results indicate that the proposed detection method not only has high accuracy of parameter estimation with short-time data window, e.g., the magnitude and frequency precision of the fault-related components reaches 10^(-4), but also overcomes the impacts of spectral leakage and non-integer-period sampling. The proposed research provides a new BRB detection method, which has enough precision to extract the parameters of the fault feature components.

Mathematical Multibody Model of a Soft Mounted Induction Motor Regarding Forced Vibrations Due to Dynamic Rotor Eccentricities Considering Electromagnetic Field Damping

The paper presents a mathematical multibody model of a soft mounted induction motor with sleeve bearings regarding forced vibrations caused by dynamic rotor eccentricities considering electromagnetic field damping. The multibody model contains the mass of the stator, rotor, shaft journals and bearing housings, the electromagnetic forces with respect of electromagnetic field damping, stiffness and internal (rotating) damping of the rotor, different kinds of dynamic rotor eccentricity, stiffness and damping of the bearing housings and end shields, stiffness and damping of the oil film of the sleeve bearings and stiffness and damping of the foundation. With this multibody model, the bearing housing vibrations and the relative shaft vibrations in the sleeve bearings can be derived.

Design and simulation of electrical dynamometer using improved DTC induction motor driver

AC motors, especially the squirrel cage induction motors have the advantages of simple structure, good reliability and low cost. They are more suitable to be used as electrical dynamometers to provide dynamic load for bench test systems. But, the speed and torque of induction motors are not easy to be controlled accurately. In this work, an electrical dynamometer based on the induction motor is proposed. In order to get better control performance of torque and speed of induction motor, an improved direct torque control method(DTC) is also developed based on the space vector modulation(SVM) technique. The performance of the proposed dynamometer system is validated in the Matlab/Simulink platform. The simulation results show that the new dynamometer has good torque and stator flux response. And the torque and stator current ripples of it are reduced significantly compared with using the conventional DTC method.