Effect of slag composition on corrosion resistance of high chromia refractory bricks for industrial entrained-flow gasifier

The slag composition corresponding to different coals varies significantly,which directly affects the operation of industrial entrained-flow gasifier and the service life of refractory bricks.In this study,the corrosion resistance of several typical coal slags for gasification on high chromia refractory bricks was comparatively investigated by static laboratory crucible tests and thermodynamic simulations.The results demonstrated that the corrosion degree of high chromia refractory bricks by different coal slags was high-Ca/Na slag>high-Fe slag>high-Si/Al slag.The surface structure of the refractory was relatively flat after corrosion by high-Si/Al slag,and the primary corrosion reaction was the partial dissolution of the matrix by the slag.High-Fe slag was prone to the precipitation of iron phases as well as the formation of(Mg,Fe)(Al,Cr)_(2)O_(4)composite spinel layer at the slag/refractory interface.The high-Ca/Na slag was susceptible to react with the refractory to yield a low melting point phase,which led to the destruction of the matrix structure of the refractory and an isolated distribution of particles.In addition,the monoclinic ZrO_(2) in the refractory reacted with CaO in the slag to formed calcium zirconate,which loosened its phase toughening effect,was the primary factor that aggravated the refractory corrosion.

Comparison of Combustion Characteristics of Tars Produced with Tobacco Stem Biomass Gasification

In order to study the combustion characteristics of tar in biomass gasifier inner wall and gasification gas,“tobacco stem semi-tar inside furnace”,“tobacco stem tar inside furnace”and“tobacco stem tar out-of-furnace”were subjected to thermogravimetric experiments,and the combustion characteristics and kinetic characteristics were analyzed.The result shows that“tobacco stem semi-tar inside furnace”has the highest value and“tobacco stem tar out-of-furnace”is has the lowest value on ignition characteristics,combustion characteristics and combustible stability;“tobacco stem semi-tar inside furnace”has the lowest value and“tobacco stem tar outside furnace”has the highest value on burnout characteristics;“tobacco stem tar outside furnace”has the highest value and“tobacco stem tar inside furnace”has the lowest value on integrated combustion characteristics.

Suppressing secondary reactions of coal pyrolysis by reducing pressure and mounting internals in fixed-bed reactor

Pyrolysis of Shenmu coal was performed in fixed-bed reactors indirectly heated by reducing operating pressure and mounting internals in the reactor to explore their synergetic effects on coal pyrolysis. Mounting internals particularly designed greatly improved the heat transfer inside coal bed and raised the yield of tar production.Reducing pressure further facilitated the production of tar through its suppression of secondary reactions occurring in the reactor. The absolute increase in tar yield reached 3.33 wt% in comparison with the pyrolysis in the reactor without internals under atmospheric pressure. The obtained tar yield in the reactor with internals under reduced pressure was even higher than the yield of Gray–King assay. Through experiments in a laboratory fixed bed reactor, it was also clarified that the effect of reducing pressure is related to volatile release rate in pyrolysis. It did not obviously vary tar yield at pyrolysis temperatures below 600 °C, while the effect was evident at 650 and 700 °C but became limited again above 800 °C. Under reduced pressure the produced tar contained more aliphatics and phenols but less aromatics.

CFD simulation on the gasification of asphalt water slurry in an entrained flow gasifier

Gasification technology is suggested to utilize asphalt particles, which are produced in the heavy oil deep separation process of using coupled low temperature separation of solvent and post extraction residue. In this work, the asphalt particles were first slurried with water and then gasified to produce synthesis gas. The gasification process of asphalt water slurry in an entrained flow gasifier was simulated using a three-dimensional computational fluid dynamics （CFD） model based on an Eulerian- Lagrangian method. The trajectories and residence time of asphalt particles, and the reaction rates, gas species distribution, temperature field and carbon conversion in the entrained flow gasifier were obtained. The predicted results indicated that the asphalt water slurry was a good feedstock for gasification. Moreover, the effects of particle size, oxygen equivalence ratio, and mass content of asphalt particles on the gasification performance of asphalt water slurry were investigated. These results are helpful for industrial application of asphalt water slurry gasification technology.

Scale up and stability test for oxidative coupling of methane over Na_2WO_4-Mn/SiO_2 catalyst in a 200 ml fixed-bed reactor

The study of scale up for the oxidative coupling of methane （OCM） has been carried out in a 200 ml stainless steel fixed-bed reactor over a 5wt% Na2WO4-1.9wt% Mn/SiO2 （W-Mn/SiO2） catalyst. The effects of reaction conditions were investigated in detail. The results showed that, with increasing reaction temperature, the gas-phase reaction was enhanced and a significant amount of methane was converted into COx; with the CH4/O2 molar ratio of 5, the highest C2 （ethylene and ethane） yield of 25% was achieved; the presence of steam （as diluent） had a positive effect on the C2 selectivity and yield. Under lower methane gaseous hourly space velocity （GHSV）, higher selectivity and yield of C2 were obtained as the result of the decrease of released heat energy. In 100 h reaction time, the C2 selectivity of 66%-61% and C2 yield of 24.2%-25.4% were achieved by a single pass without any significant loss in catalytic performance.

Conversion enhancement of tubular fixed-bed reactor for Fischer-Tropsch synthesis using static mixer

Recently, Fischer-Tropsch synthesis （FTS） has become an interesting technology because of its potential role in producing biofuels via Biomass- to-Liquids （BTL） processes. In Fischer-Tropsch （FT） section, biomass-derived syngas, mainly composed of a mixture of carbon monoxide （CO） and hydrogen （H2）, is converted into various forms of hydrocarbon products over a catalyst at specified temperature and pressure. Fixed-bed reactors are typically used for these processes as conventional FT reactors. The fixed-bed or packed-bed type reactor has its drawbacks, which are heat transfer limitation, i.e. a hot spot problem involved highly exothermic characteristics of FT reaction, and mass transfer limitation due to the condensation of liquid hydrocarbon products occurred on catalyst surface. This work is initiated to develop a new chemical reactor design in which a better distribution of gaseous reactants and hydrocarbon products could be achieved, and led to higher throughput and conversion. The main goal of the research is the enhancement of a fixed-bed reactor, focusing on the application of KenicsTM static mixer insertion in the tubular packed-bed reactor. Two FTS experiments were carried out using two reactors i.e., with and without static mixer insertion within catalytic beds. The modeled syngas used was a mixed gas composed of H2/CO in 2 ： 1 molar ratio that was fed at the rate of 30 mL（STP）·min^- 1 （GHSV ≈ 136 mL·gcat^-1 ·h^-1） into the fixed Ru supported aluminum catalyst bed of weight 13.3 g. The reaction was carried out at 180 ℃ and atmospheric pressure continuously for 36 h for both experiments. Both transient and steady-state conversions （in terms of time on stream） were reported. The results revealed that the steady-state CO conversion for the case using the static mixer was approximately 3.5 times higher than that of the case without static mixer. In both cases, the values of chain growth probability of hydrocarbon products （α） for Fischer-Tropsch synthesis were 0.92 and 0.89 for the case with and without static mixer, respectively.

Assessment of coal gasification in a pressurized fixed bed gasifier using an ASPEN plus and Euler–Euler model

With the help of Aspen Plus,a two-dimensional unsteady CFD model is developed to simulate the coal gasification process in a fixed bed gasifier.A developed and validated two dimensional CFD model for coal gasification has been used to predict and assess the viability of the syngas generation from coal gasification employing the updraft fixed bed gasifier.The process rate model and the sub-model of gas generation are determined.The particle size variation and char burning during gasification are also taken into account.In order to verify the model and increase the understanding of gasification characteristics,a set of experiments and numerical comparisons have been carried out.The simulated results in the bed are used to predict the composition of syngas and the conversion of carbon.The model proposed in this paper is a promising tool for simulating the coal gasification process in a fixed bed gasifier.

Damage Mechanism of High Chrome Bricks for Opposed Multi Nozzle Gasifier and Their Improvement

To reveal the damage mechanism of high chrome bricks for opposed multi nozzle gasifier with expanded diameter,the chemical composition and the morphology of a used high chrome brick were researched using XRF,SEM and EDS,and the properties of the high chrome bricks were improved by adding ultra fine alumina,alumina-chrome-iron oxide synthetic material with spinel structure,and chromium metal.The results show that(1)the high chrome brick is seriously damaged by the chemical dissolution of chrome as well as the chemical reactions at the slag/brick interface,the slag penetration and the structural spalling;(2)FeO in the slag reacts with Cr_(2)O_(3)in the brick to form a FeCr_(2)O_(4)layer on the particle surface thus leading to spalling;CaO reacts with SiO_(2)and Al2O3 in the brick forming a metamorphic layer of low melting point materials;due to the different thermal expansion coefficients of the metamorphic layer and the original brick,cracks appear and continue to expand and deepen under multiple temperature and pressure fluctuations thus leading to spalling of brick layer;(3)the improved brick has decreased apparent porosity,increased bulk density and compressive strength,and better thermal shock resistance compared with the original brick;after one cycle of on-site application,the furnace lining surface is smooth and flat with little damage,indicating that the improved high chrome bricks basically meet the working condition requirements of the opposed multi nozzle gasifier with expanded diameter,however,the final effects need to be evaluated in detail after the whole furnace service.

Variation of toxic pollutants emission during a feeding cycle from an updraft fixed bed gasifier for disposing rural solid waste

The variation of toxic pollutants emission during a feeding cycle was examined by field monitoring from a batch feeding updraft fixed bed gasifier for disposing rural domestic solid waste. Results showed that the content of oxygen in flue gas gradually increased, while SO_2 and HCl in flue gas decreased with time after feeding in a whole feeding cycle. Although large amount of CO was produced during the gasifying, low CO content in flue gas could be obtained after the heat treatment with an electric heating device. The distribution characteristics of dioxin congeners in flue gas indicted the re-synthesis of dioxins after flue gas heating, and the increase of oxygen promoted the synthesis of dioxins. The emission content of dioxins could meet the standard(0.1 ng I-TEQ·m^(-3),GB18458-2014) of China when the oxygen content was controlled below 8.3%. Hence, for a batch feeding gasifier,low oxygen condition should be offered by reducing air intake at the later stage of feeding cycle in order to decrease the re-synthesis of dioxins after the flue gas heating.

Syngas cleaning with nano-structured micro-porous ion exchange polymers in biomass gasification using a novel downdraft gasifier

Sulphonated nano-structured micro-porous ion exchange polymers, known as sulphonated PolyHIPE Polymers （s-PHPs） were used in syngas cleaning to investigate their impact on tar composition, concentration and dew point depression during the gasification of fuel cane bagasse as a model biomass. The results showed that the s-PHPs used as a secondary syngas treatment system, was highly effective at adsorbing and reducing the concentration of all class of tars in syngas by 95%-80% which resulted in tar dew point depression from 90 ~C to 73 ~C. It was shown that tars underwent chemical reactions within s-PHPs, indicating that tar diffusion from syngas was driven by chemical potential. It was also observed that s-PHPs also captured ash forming elements from syngas. The use of s-PHPs in gasification as well as in an integrated thermochemical biorefinery technology is discussed since the tar loaded s-PHPs can be used as natural herbicides in the form of soil additives to enhance the biomass growth and crop yield.

Refractories Utilizability for Slagging Gasifiers

Slagging coal gasification process became a highlight of coal chemical industry in China during the last decade. Refractory lining＇ s life of slagging gasifiers is one of the most critical factors for a cost - effective operation. The paper introduces current status of coal gasification in China, lining structure of slagging gasifiers and performance of refractory lining. It also summarizes the major factors impacting on refractory wear in slagging coal gasifiers in four Chinese chemical plants, based on ten years of industrial experience. The utilizability is discussed in terms of cost -effectiveness of high chromia refractories and possibility of the alternatives.

Study on Microstructure and Slag Corrosion Mechanism of High Chrome Bricks for Gasifier

Research was focused on slag corrosion mechanism of high chrome bricks used for different types of gasifier by comparing the structure of high chrome bricks for petroleum coke gasifier and water-coal slurry gasifier with slag corroded testing brick and water coal slurry gasifier through Scanning Electron Microscope （SEM） examination and X-ray diffi＇action. Results show that for high chrome brick used for petroleum coke gasifier, corrosion is mainly caused by Cr2O3 in the brick and V2O5 in molten slag and liquid phase generation at low temperature; for high chrome brick used for water-coal slurry gasifier, corrosion is caused by dissolution of Cr2O3 in molten slag and corrosion of ZrO2. For LIRR-HK95 brick, it performs better petroleum coke corrosion resistance than the others due to the optimal composition and structure.

STUDY ON THE VARIATION MECHANISM OF CARBON CONTENT OF LIQUID IRON IN MELTING GASIFIER

This paper studied the changing principles of carbon content in direct reduction iron (DRI) and liquid iron in the COREX melting gasifier. Under the normal working conditions of experimental equipment, liquid nitrogen was poured into the melting gasifier from its tuyere to cool down quickly. And then seven cross sections were made to study the carburization reaction and its characteristics of the solid iron and the liquid iron, and also the reaction of carbon between the slag and the metal. According to the results, the influences of the thickness of the semi-coke layer and the temperature on the carbon content of liquid iron in the COREX melting gasifier were confirmed.

Discussion on Wear Mechanism of High Chrome Brick Used in Coal Slurry Gasifier

The microstructure and phase composition of high chrome brick used in coal slurry gasifier has been analyzed by means of SEM and Energy Spectrum. The results indicate that the used brick can be divided into different zones as slag-adhered zone, reaction zone, penetration zone and unaltered zone. The phase composition and microstructure are different and cracks occurred in different degree at these zones. A dense ring belt was formed with complex spinel (Mg,Fe)(Cr,Al,Fe 2O 4) in the reaction zone near the hot face. The wear mechanism of the brick during its employment has been discussed. It is considered that the reaction and penetration of coal slag and strong reductant bring about the composition change of the brick and destroys its original network inlayed structure and consequently result in its structure spalling and weakening strength, which is the main wear mechanism of the brick and followed by temperature fluctuation and high mechanical impact of flowing fluid with high-speed.

Analysis and Design Innovation on Underground Gasifier for Medium-Deep Coal Seam

Over the past 80 years,dozens of underground coal gasification(UCG)mine field tests have been carried out around the world.However,in the early days,only a small number of shallow UCG projects in the former Soviet Union achieved commercialised production.In this century,a few pilot projects in Australia also achieved short-term small-scale commercialised production using modern UCG technology.However,the commercialisation of UCG,especially medium-deep UCG projects with good development prospects but difficult underground engineering conditions,has not progressed smoothly around the world.Considering investment economy,a single gasifier must realise a high daily output and accumulated output,as well as hold a long gasification tunnel to control a large number of coal resources.However,a long gasification tunnel can easily be affected by blockages and failure,for which the remedial solutions are difficult and expensive,which greatly restricts the investment economy.The design of the underground gasifier determines the success or failure of UCG projects,and it also requires the related petroleum engineering technology.Combining the advantages of the linear horizontal well(L-CRIP)and parallel horizontal well(P-CRIP),this paper proposes a new design scheme for an“inclined ladder”underground gasifier.That is to say,the combination of the main shaft of paired P-CRIP and multiple branch horizontal well gasification tunnels is adopted to realise the control of a large number of coal resources in a single gasifier.The completion of the main shaft by well cementation is beneficial for maintaining the integrity of the main shaft and the stability of the main structure.The branch horizontal well is used as the gasification tunnel,but the length and number of retracting injection points are limited,effectively reducing the probability of blockage or failure.The branch horizontal well spacing can be adjusted flexibly to avoid minor faults and large cracks,which is conducive to increasing the resource utilisation rate.In addition,for multi-layer thin coal seams or ultra-thick coal seams,a multi-layer gasifier sharing vertical well sections can be deployed,thereby saving investment on the vertical well sections.Through preliminary analysis,this gasifier design scheme can be realised in engineering,making it suitable for largescale deployment where it can increase the resource utilisation rate and ensure stable and controllable operations.The new gasifier has outstanding advantages in investment economy,and good prospects for application in the commercial UCG projects of medium-deep coal seams.

Numerical Simulation of Thermal Stress Field of Water-cooled-wall Pulverized-coal Gasifiers

the stress field in the gasifier operation to research the damage of refractories and slag layer caused by the thermal stress.The results reveal that:(1)the maximum stress of water-cooled-wall gasifier appears at the interface between anchor nails and refractories as well as the interface between refractories and the slag layer,and the maximum stress of slag layer appears on the surface of the slag layer;(2)the increase of slag layer thickness can significantly reduce the thermal stress at the interface between anchor nails and refractories,but increase the thermal stress between slag layer and refractories;(3)when the thermal conductivity is 2-6 W•m^-1•K^-1,the thermal stress increases rapidly with the increase of the thermal conductivity,but when the thermal conductivity is 6-10 W•m^-1•K^-1,the thermal stress is basically stable;(4)the higher the cooling rate,the faster the decreasing speed of the temperature and thermal stress.

Analysis of Spent High Chrome Brick in Slagging Gasifier

Wear of the spent high chrome brick in slagging gasifier was studied. The result shows that erosion and spalling are the m, ain wear mechanism of high chrome brick and the CaO content of coal slag is crucial to wear of high chrome brick.

Main Influencing Factors on Service Life of High Chrome Refractories for Coal Water Slurry Gasifiers

The main characteristics of high chrome refractories for coal water slurry gasifiers were introduced. The damage mechanism of the refractories was analyzed by observing the microstructure of the used high chrome refractories with the aid of SEM. The main influencing factors on the service life of the refractories were summarized.

Investigation into characteristics of the char bed in the melter gasifier through tuyere probing

Tuyere coke probing was conducted at the Baosteel Corex Plant in order to gain a better understanding of the structure of the char bed in the melter gasifier （ MG ）. After screening, the specimens were observed by an optical microscope to determine the mechanism of the char bed formation. X-ray diffraction （XRD） was used to clarify the degree of graphitization and infer thermal history of coke. The results show that the amount of powder coming from lump coal in the burden is much more than that from coke. Based on this, measures for improving the char bed＇ s permeability are proposed.

DETERMINATION OF PARAMETERS IN A TWO-DIMENSIONAL MODEL FOR FIXED-BED ADSORBERS

A new method is proposed for the determination of the parameters in a two-dimensionalmodel which characterizes the properties of axial and radial mixing and mass transport in afixed-bed adsorber.Parameter estimation for the model is carried out with methane-air-5A molecularsieve in a bed under the condition of step injection of tracer from a point on the main axis of thebed by the curve fitting method in the time domain.