On Switching of a Flip-Flop Jet Nozzle with Double Ports by Single-Port Control

This research deals with the oscillation mechanism of a flip-flop jet nozzle with a connecting tube, based on the measurements of pressures and velocities in the connecting tube and inside the nozzle. The measurements are carried out varying: 1) the inside diameter d of the connecting tube;2) the length L of the connecting tube and 3) the jet velocity VPN from a primary-nozzle exit. We assume that the jet switches when a time integral reaches a certain value. At first, as the time integral, we introduce the accumulated flow work of pressure, namely, the time integral of mass flux through a connecting tube into the jet-reattaching wall from the opposite jet-un-reattaching wall. Under the assumption, the trace of pressure difference between both the ends of the connecting tube is simply modeled on the basis of measurements, and the flow velocity in the connecting tube is computed as incompressible flow. Second, in order to discuss the physics of the accumulated flow work further, we conduct another experiment in single-port control where the inflow from the control port on the jet-reattaching wall is forcibly controlled and the other control port on the opposite jet-un-reattaching wall is sealed, instead of the experiment in regular jet’s oscillation using the ordinary nozzle with two control ports in connection. As a result, it is found that the accumulated flow work is adequate to determine the dominant jet- oscillation frequency. In the experiment in single-port control, the accumulated flow work of the inflow until the jet’s switching well agrees with that in regular jet’s oscillation using the ordinary nozzle.

The Optimization Design of the Nozzle Section for theWater Jet Propulsion System Applied in Jet Skis

The performance of a water jet propulsion system is related to the inlet duct,rotor,stator,and nozzle.Generally,the flow inlet design must fit the bottom line of the hull,and the design of the inlet duct is often limited by stern space.The entire section,from the rotor to the nozzle through the stator,must be designed based on system integration in that the individual performance of these three components will influence each other.Particularly,the section from the rotor to the nozzle significantly impacts the performance of a water jet propulsion system.This study focused on nozzle design and established referable analysis results to facilitate subsequent integrated studies on the design parameters regarding nozzle contour.Most existing studies concentrate on discussions on rotor design and the tip leakage flow of rotors or have replaced the existing complex computational domain with a simple flow field.However,research has yet to implement an integrated,optimal design of the section from the rotor to the nozzle.Given the above,our program conducted preliminary research on this system integration design issue,discussed the optimal nozzle for this section in-depth,and proposed design suggestions based on the findings.This program used an existing model as the design case.This study referred to the actual trial data as the design conditions for the proposed model.Unlike prior references’simple flow field form,this study added a jet ski geometry and free surface to the computational domain.After the linear hull shape was considered,the inflow in the inlet duct would be closer to the actual condition.Based on the numerical calculation result,this study recommends that the optimal nozzle outlet area should be 37%of the inlet area and that the nozzle contour should be linear.Furthermore,for the pump head,static pressure had a more significant impact than dynamic pressure.

Jet Characteristics and Optimization of a Cavitation Nozzle for Hydraulic Fracturing Applications

Hydraulic jetting is a form of fracturing that involves using a high-pressure jet of water to create fractures in the reservoir rock with a nozzle serving as the central component of the hydraulic sandblasting perforation tool.In this study,the flow behavior of the nozzle is simulated numerically in the framework of a SST k-ωturbulence model.The results show that the nozzle structure can significantly influence the jet performance and related cavitation effect.Through orthogonal experiments,the nozzle geometric parameters are optimized,and the following configuration is found accordingly:contraction angle 20°,contraction segment length 6 mm,cylindrical segment diameter 6 mm,cylindrical segment length 12 mm,spread segment length 10 mm,and spread angle 55°.

THEORY AND EXPERIMENTAL STUDY OF THE SELF-EXCITED OSCILLATION PULSED JET NOZZLE

Comparing with usual continuous jet nozzle, the self-excited oscillationpulsed jet nozzle SEOPJN) can make jet generate a higher peak of pressure and larger scouringvolume. And it can make jet increase the effective standoff distance, too. The basic theories of theSEOPJN are introduced. Some experimental results are shown. According to the results, using tricornbits assembled the SEOPJN to drill oil well, the ROP increases by 8 percent approx 77 percent, andthe rates of the footage for tricorn bit increases by 6.7 percent approx 44.0 percent.

Experimental Study on Reaction Thrust Characteristics of Water Jet for Conical Nozzle

Water jet thruster, which is a marine system that creates a jet of water for propulsion, has several advantages such as low noise, good anti-cavitation characteristics and maneuvering characteristics. The reaction thrust characteristics of water jet for conical nozzles directly determine the speed of autonomous underwater vehicles （AUV）. Theoretical, numerical and experimental studies have been, carried out to investigate the effects of the nozzle geometries as well as inlet conditions on the reaction thrust of water jet in this paper. The experimental results show that： 1） the reaction thrust is proportional to inlet pressure, the square of flow rate and 2/3 power exponent of input power; 2） the diameter of cylinder column for conical nozzle has great influence on the reaction thrust characteristics; 3） the best values of the half cone angle and the cylinder column length exist to make the reaction thrust coefficient to reach the maximum under the same inlet conditions. Those provide a basis for nozzles design and have significant value, especially for developing high performance and efficiency water jet propulsion unit.

Effect of Geometrical Parameters on Submerged Cavitation Jet Discharged from Profiled Central-body Nozzle

The flow characteristics of cavitation jets are essential issues among relevant studies. The physical properties of the jet are largely determined by the geometrical parameters of the nozzle. The structure and cavitation jets characteristics of the angular-nozzle and the self-resonating cavitation nozzle have been extensively studied, but little research is conducted in the central-body cavitation nozzle mainly because of its hard processing and the cavitation jet effect not satisfactory. In this paper, a novel central-body nozzle (a non-plunger central-body nozzle with square outlet) is studied to solve above problems. Submerged jets discharged from the novel central-body nozzle are simulated, employing the full cavitation model. The impact of nozzle configuration on jet properties is analyzed. The analysis results indicate that when central-body relative diameter keeps constant, there is an optimal contraction degree of nozzle’s outlet, which can induce intense cavitation in the jet. The central-body relative diameter also affects jet profiles. In the case of large central-body relative diameter, most of the bubbles settle in the jet core. On the contrary, a smaller relative diameter makes bubbles concentrate in the interface between the jet and its surrounding fluid. Moreover, the shorter outlet part allows the cavitation zone further extend in both the axial and racial directions. The research results further consummate the study on the central-body nozzles and the correlation between cavitation jet and the structure, and elementarily reveal the mechanism of cavitation jet produced in a non-plunger novel central-body nozzle and the effect of the structure parameters on the cavitation jet, moreover, provide the theoretical basis for the optimal design of the nozzle.

Numerical Investigation on the Influence of Nozzle Lip Thickness on the Flow Field and Performance of an Annular Jet Pump

The performance of an annular jet pump( AJP) is determined by its area ratio A( ratio of cross sectional area of throat and annular nozzle) and flow rate ratio q( ratio of primary and secondary flow rate,Qs/Qj),while the nozzle lip thickness is neglected in the present studies. This paper presents a study on the effect of the thickness on the flow field and performance of an AJP with A = 1. 75. With the increasing flow rate ratio and nozzle lip thickness,a small vortex forms at the nozzle lip and keeps on growing. However,as the flow rate ratio or nozzle lip thickness is extremely low,the vortex at the lip vanishes thoroughly. Moreover,the recirculation width varies conversely with the nozzle lip thickness when the flow rate ratio q ≤ 0. 13. While the deviation of the recirculation width with different nozzle lip thickness is negligible with q ≥ 0. 13. Additionally the existence of nozzle lip hinders the momentum exchange between the primary and secondary flow and leads to a mutation of velocity gradient near the nozzle exit,which shift the recirculation downstream. Finally,based on the numerical results of the streamwise and spanwise vortex distributions in the suction chamber, the characteristics of the mixing process and the main factors accounting for the AJP performance are clarified.

Numerical Simulation Research of Liquid-Solid Two-Phase Flow in Abrasive Water Jet Nozzle

According to the Lagrange discrete phase model of multiphase flow, mathematical model of the abrasive water-jet （AWJ） nozzle based on the multi-phase movement was introduced, then the boundary conditions was determined and the liquid-solid turbulence which is isothermal, can not be compressed and steadystate in the cone-cylinder nozzles of the export of the pre-mixed AWJ was simulated applying the software FLUENT. The results showed that： the axial velocity and dynamic pressure of the continuous phase in the nozzle were axial symmetry notable, and at the axis had a extreme point; abrasive accelerated at two points, in front contractive segment, the rate increased rapidly, and in the back straight one, the speed accelerated slowly. The length of the cylinder is 100 mm, the diameter of the nozzle is 8 mm, and the angle of the cone is 15°. There is a extreme point of the rate at the point 10 mm in the established model. The results of simulation laid the foundation for optimizing the nozzle structure, improving efficiency and developing the nozzle.

Experiment and Numerical Simulation of Free Water Jet by a Central-body Nozzle

The recent research about cavitation jet mainly focuses on the organ-pipe nozzle and triangular nozzle. The research content mainly includes the optimized design about the structure of nozzles, the observation and flow analysis about the cavitation jet in the water, and the theory of rock attacked by the cavitation jet, while the energy characteristic of the free jet is not studied yet. In China, the research about the central-body nozzle is almost empty. For the purpose of studying the energy characteristic and the structure of free water jet discharged from central-body nozzle, an experiment with phase Doppler particle anemometry（PDPA） technology is carried out to measure the free water jet flow, which is produced by a central-body nozzle under the jet pressure of 15 MPa. While five sections with different axial distances from the nozzle outlet are selected for data process and analysis, the axial and radial velocity and the droplets of the particle size are studied. Meanwhile, numerical calculation of corresponding flow field is conducted by using volume of fluid（VOF） multiphase model, and the jet flow feature is discussed. The experimental and calculating results show that the axial velocity of high speed jet flow dissipates slowly in the air, and the core area and diffused area are discovered. The diameter of droplet in the core area is small, and jet energy is concentrated, while in the diffusion area, water is mingled with ambient air and radial velocity is relatively large. Obvious low-pressure area exists behind the central body and potential cavitation may occur in that area. The proposed research reveals the energy characteristic of free jet discharged from central-body nozzle, provides the theoretical basis for preestimating erosion feature of the central-body nozzle and also the theoretical foundation for revealing the mechanism of erosion.

Flow-visualization and numerical investigation on the optimum design of cavitating jet nozzle

Cavitating jet is widely used in drilling,rock cutting and ocean re source exploitation because of its stro ng erosion ability.The analysis of the relationship between the flow characteristics and the structure of cavitating jet nozzle is critical.Here,we utilized 3 D printed technology and high-speed photography to design visualization experime nts to analyse the impact of the variation of resonator and throat size of the organ-pipe self-resonating cavitating nozzles on the cavitation characteristics through image processing.The velocity field,pressure field and vapor volume fraction injected by the nozzle were taken as the objective functions to study the influence of different structural parameters on the cavitation effect based on FLUENT 19.0 software,and the results were compared with the experimental results.The results show that increasing the length and diameter of the resonator contributes to the occurrence of cavitation and the structure stability of the flow field.However,excessive size affects self-resonant of the nozzle and makes it difficult to form resonance effect.In this study,the optimal values of nozzle throat length and divergent angle are twice the throat diameter and 40°,respectively.This research provides an integrated research method to study the optimization of self-resonating nozzle and cavitating jet characteristics.

Transient heat transfer characteristics of air-array-jet impingement with different nozzle arrangements on high-tempera-ture flat plate in small jet-to-plate distance

Numerical studies on transient heat transfer characteristics of air-array-jet impingement with a small jet-to-plate distance and a large temperature difference between nozzles and plate were presented.The dimensionless jet-to-plate distance(H/D)was 0.2,and non-dimensional nozzle-to-nozzle spacing(S/D)was 3,4,5 and 6,respectively.It is found that the quenching time is shortened at a constant total mass flow at air jet inlet m·(m·=218.21 kg/h),and the heat transfer uniformity is deterio-rated as S/D increases.However,the adding reversed-flow nozzles can shorten the quenching time of the glass plate considerably with a modest change in the heat transfer uniformity.The results at variable m·are the same as those at a fixed m·.Furthermore,the parity and arrangement of nozzles are also discussed,It is found that an odd number of nozzles is more beneficial for transient heat transfer.Based on these results,an appropriate proposal for ultra-thin glass tempering process is presented.

Passive Control of Turbulent Jet Flow with Wedged Nozzle

Turbulent flow field of the free jet with circular nozzle and wedged nozzles is measured using hot wire anemometry with resolution higher than the smallest turbulence time scale. Wavelet analysis is employed to perform multi-scale decomposition of instantaneous turbulence fluctuating velocity signals, and the energy distribution of the turbulent multi-scale eddy structures over scales is studied using wavelet coefficients. Investigation of the multi-scale eddy structures of circular jet and various wedged jets reveals the transport of the energy of these wedged jets in the space from the axis to the side of the jet, as compared with the circular jet. Furthermore, not only the eddy structures at the wedge tines in the near field are crashed, but also the interactions such as eddy structure union and entrainment take place at different longitudinal and normal locations along with the development of the jets because of the existence of wedges.

A swirling jet from a nozzle with tangential inlets and its characteristics in breaking-up rocks

In order to apply a swirling jet to a PDC drill bit, the nozzle performance influenced by nozzle inlet geometric parameters and rock breaking tests under submerged conditions were studied. Numerical simulation was used to study the influence of the nozzle structure on the swirling intensity and nozzle discharge coefficient. Simulation results indicate that spreading angle of the swirling jet is greater than that of＂ the non-swirling jet, and the swirling intensity of the jet is strongly influenced by the length of the nozzle body but weakly by the number of tangential inlets. Rock breaking tests were conducted to evaluate the performance of the swirling jet. It is found that the swirling jet shows a lower threshold pressure to break the rock samples and could break rock more efficiently compared with the non-swirling jet.

Reaction thrust of water jet for conical nozzles

Clear knowledge on the reaction thrust of water jet is valuable for better design of water jet propulsion system. In this paper, theoretical, numerical and experimental studies were carried out to investigate the effects of the nozzle geometry as-well as the inlet conditions on the reaction thrust of water jet. Comparison analyses reveal that the reaction thrust has a direct proportional relationship with the product of the inlet pressure, the square of flow rate and two-thirds power exponent of the input power. The results also indicate that the diameter of the cylinder column for the conical nozzle has great influence on the reaction thrust characteristics. In addition, the best values of the half cone angle and the cylinder column length exist to make the reaction thrust reach its maximum under the same inlet conditions.

The Theory and Experimental Study of the Self-Excited Oscillation Pulsed Jet Nozzle (Pipeline Pulsed Flow Generator)

In this paper, the basic theories of the Self-excited Oscillation Pulsed Jet Nozzle (SEOPJN) invented by the authors are introduced. Then, some experimental results are shown. According to the results, using tricorn bits assembled the SEOPJN to drill oil well, the rate of penetration (ROP) increases by 8% - 77%, and the rate of the footage for tricorn bit increases by 6.7% - 44%. Although the test was conducted in the water, good result was got in nature gas transportation. The volume of gas transportation could be increased by the Self-excited Oscillation Pulsed generator while the gas pressure drop could be decreased, since it significantly reduced the pressure loss during gas transportation.

Reaction thrust characteristics of high-pressure submerged water jet of cylinder nozzles

The shapes and geometrical parameters of nozzles are key factors for fluidics. The relationship among the reaction thrust, flow rate pressure, diameter do and length L of a cylinder nozzle is analyzed theoretically. The simulation of the flow field characteristics was conducted via the FLUENT computational fluid dynamics package. Effects of the inlet conditions and the nozzle dimensions on the reaction thrust of a water jet were addressed particularly. The reaction thrust experiments were performed on a custom-designed test apparatus. The experimental results reveal that a） the nozzle diameter and the inlet conditions exert great influence on the water jet reaction thrust; and b） for L≤4d0, where the nozzle is treated as a thin plate-orifice, the reaction thrust is independent of nozzle length; for L〉4d0, where the nozzle is treated as a long orifice, the reaction thrust can reach maximum under the condition of a certain flow rate. These findings lay a theoretical foundation for the design of nozzles and have significant value, especially for the future development of high-oressure water-let orooulsion technology.

Experimental investigation of crossflow characteristics in multi-jets system at small nozzle-to-plate spacing

To further extend knowledge about the detailed knowledge on the crossflow characteristics in a multi-jets system under a confined space,particle image velocimetry (PIV) was employed to investigate the flow structures together with the distributions of the mean velocity components for Reynolds numbers (Re) ranging from 6 213 to 13 418,nozzle-to-plate spacing (H/D) varying from 0. 20 to1. 25,respectively. Results show that the crossflow configuration is significantly different from those of large nozzle-to-plate spacing. In addition,a turning point H/D=0.50 is revealed in the profile of the normalized maximum radial velocity which is associated with the heat transfer distribution on the impingement plate.

Experimental and Numerical Evaluation of the Cavitation Performances of Self-Excited Oscillating Jets

Self-excited oscillating jets(SOJ)are used in several practical applications.Their performances are significantly affected by structural parameters and the target distance.In this study,a geometric model of the SOJ nozzle accounting for multiple structural parameters is introduced,then the related cavitation performances and the optimal target distance are investigated using a Large-Eddy Simulation(LES)approach.Results are also provided about an experiment,which was conducted to validate the simulation results.By analyzing the evolution of the vapor volume fraction at the nozzle outlet,a discussion is presented about the effect of the aforementioned structural parameters on the cavitation performances and the target distance.It is shown that the distribution of cavitation clouds at the outlet of the SOJ nozzle displays a non-monotonic trend(first increasing,then decreasing).Under working conditions with an inlet pressure of 4 MPa,a SOJ nozzle outlet/inlet diameter ratio(D_(1)/D_(2))of 1.2,and a chamber diameter ratio(D/L)close to 1.8,the nozzle outlet cavitation performance attains a maximum.The optimal structural parameters correspond to the optimal target distance,which is near 50 mm.The experiments have revealed that the SOJ nozzle with the above parameters displays a good cavitation erosion effect at the target distance of 50 mm,in satisfactory agreement with the numerical simulation results.

Time Characterization of High Density Gas Jet from a Pulsed Supersonic Nozzle via Laser Produced Plasma

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10μs with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 10^19 cm^-3, compared with theoretical simulations from the nozzle parameters.

The Acoustic Performance of 3D Printed Multiple Jet Nozzles with DifferentConfigurations

This work investigated multiple jet nozzles with various geometrical shape,number of exits,and material on reducing noise radiated from jet flows.Nozzles are categorized in two groups with few and many exit numbers,each with various exit shapes,slot and circular,and geometry.Firstly,nozzles are designed and then fabricated by a 3D printer,Form Labs,Form2USA,with polymeric resin.Also,the nozzle with the most noise reduction made of stainless steel.Noise and air thrust were measured at three air pressure gauges,3,5,7 BAR and directions from nozzle apex,30°,90°,135°.Nozzles with slot exit shape made of both plastic and stainless steel revealed the most noise reduction among all nozzles with few exit numbers,nearly 11–14 dB(A)and 11.5–15 dB(A),respectively.On average,slotted nozzle noise reduction was nearly 5–6 dB(A)more than finned nozzle.However,nozzles with more exit numbers,finned and finned-central exit,illustrated much more noise reduction than nozzles with few exit numbers,by almost 16–18 dB(A),they represented similar sound.All tested nozzles and open pipe demonstrated equal air thrust at each pressure gauges.The nozzles with slotted exit shape,either plastic or stainless steel,can provide reasonable noise reduction in comparison to other configuration with few exit numbers.In contrast,nozzles with more exit numbers demonstrated the most noise reduction.