LDA Study of Particulate Flow in a Channel with Deformed Surface Locations and with Flow Conditioner

Hydroabrasion in particulate flows plays an important role in various industrial and natural processes. To predict the effects of particulate flow and the resulting phenomena such as erosion/abrasion in a pipeline, channel or a fitting, it is essential to characterize the effects in a simple standardized geometry. For this purpose, it is vital to initially understand the particulate flow behavior and motion in such geometries. In the present work, two series of experimental works by application of the LDA measurement technique were successfully conducted. First, the particulate flow behavior at downstream of a flow conditioner inside a channel with square cross-section was investigated. Shorter lengths for fully development of velocity profile by using the self-constructed flow conditioner were observed. Moreover, the flow at downstream of the conditioner was modeled with the CFD tool (ANSYS-CFX V. 14.57) and the simulation results were compared and validated by the LDA experimental data. Better agreement between the simulation results and experimental data was observed in the fully developed region. However, there are some deviations due to the actual pressure loss through the experimental loop and the calculated pressure loss value, which includes some assumptions for the loss coefficients. Furthermore, the particulate flow behavior and vortex generation inside the deformed locations of a channel surface were studied in detail. With the help of the Matlab program, it was possible to calculate and visualize the velocity vectors for each measured point inside the channel accurately.

CFD-Aided Investigation of Combined Flow Conditioners for Gas Ultrasonic Flow Meter

Stable and fully developed gas flow field is crucial for realizing accurate measurement of gas ultrasonicflow meter. To reduce the flow field distortion, a flow conditioner is usually used. However, the traditionalmonotype flow conditioner can only improve the flow field distribution partly. The measurement accuracy of thetransit time ultrasonic flow meter is still affected because of its serious flow field distortion in the complex pipelineconditions. In this paper, to further improve the flow field distribution, a combined conditioner is investigated.The combined flow conditioner is composed of fan-shaped section, turbulent mixing cavity, and honeycomb-shapedsection. The effects of fan blade angle and cavity length on the flow field of the DN50 flow meter are studied usingcomputational fluid dynamics (CFD) simulation. Simulation results indicate that compared with the monotypeconditioner, the combined conditioner has better performance on effectively reducing the swirl and turbulence andproviding more stable and repetitive velocity profiles. Experiments also validate the effectiveness of the combinedconditioner. The flow meter with the combined conditioner has better repeatability of less than 0.2%, which isbetter than those of the monotype conditioners under the same conditions. This work is very useful for accuratemeasurement of gas ultrasonic flow meter, especially for the complex pipeline conditions.

Case History of the Disastrous Debris Flows of Tianmo Watershed in Bomi County, Tibet, China: Some Mitigation Suggestions

Debris flows and landslides, extensively developing and frequently occurring along Parlung Zangbo, seriously damage the Highway from Sichuan to Tiebt(G318) at Bomi County. The disastrous debris flows of the Tianmo Watershed on Sept. 4, 2007, July 25, 2010 and Sept. 4, 2010, blocked Parlung Zangbo River and produced dammed lakes, whose outburst flow made 50 m high terrace collapse at the opposite bank due to intense scouring on the foot of the terrace. As a result, the traffic was interrupted for 16 days in 2010 because that 900 m highway base was destructed and 430 m ruined. These debris flows were initiated by the glacial melting which was induced by continuous higher temperature and the following intensive rainfall, and expanded by moraines along channels and then blocked Parlung Zangbo. At the outlet of watershed,the density, velocity and peak discharge of debris flow was 2.06 t/m3, 12.7 m/s and 3334 m3/s, respectively. When the discharge at the outlet and the deposition volume into river exceeds 2125 m3/s and 126×103 m3, respectively, debris flow will completely blocked Parlung Zangbo. Moreover,if the shear stress of river flow on the foot of terrace and the inclination angel of terrace overruns 0. 377 N/m2 and 26°, respectively, the unconsolidated terrace will be eroded by outburst flow and collapse. It was strongly recommended for mitigation that identify and evade disastrous debris flows, reduce the junction angel of channels between river and watershed, build protecting wall for highway base and keep appropriate distance between highway and the edge of unconsolidated terrace.

Platelet adhesion to the surface of a sudden tubular expansion tube under swirling flow condition

The size mismatch in an end-to-end vascular anastomosis between the host vessel and the graft may cause flow disturbance and predispose to thrombosis [1].Although a number of techniques have been employed to reduce the risk of anastomotic thrombosis due to the size mismatch。

Numerical study of homogeneous–heterogeneous reactions on stagnation point flow of ferrofluid with non-linear slip condition

This study deals with the stagnation point flow of ferrofluid over a flat plate with non-linear slip boundary condition in the presence of homogeneous-heterogeneous reactions.Three kinds of ferroparticles,namely,magnetite(Fe_3O_4),cobalt ferrite(CoFe_2O_4) and manganese zinc ferrite(Mn-ZnFe_2O_4) are taken into account with water and kerosene as conventional base fluids.The developed model of homogeneous-heterogeneous reactions in boundary layer flow with equal and unequal diffusivities for reactant and autocatalysis is considered.The governing partial differential equations are converted into system of non-linear ordinary differential equations by mean of similarity transformations.These ordinary differential equations are integrated numerically using shooting method.The effects of pertinent parameters on velocity and concentration profiles are presented graphically and discussed.We found that in the presence of Fe_3O_4-kerosene and CoFe_2O_4-kerosene,velocity profiles increase for large values of α and β whereas there is a decrement in concentration profiles with increasing values of if and K_s.Furthermore,the comparison between non-magnetic(A1_2O_3) and magnetic Fe_3O_4 nanoparticles is given in tabular form.

Interaction between Topographic Conditions and Entrainment Rate in Numerical Simulations of Debris Flow

Debris flow simulations are useful for predicting the sediment supplied to watersheds from upstream areas. However, the topographic conditions upstream are more complicated than those downstream and the relationship between the topographic conditions and debris flow initiation is not well understood. This study compared the use of several entrainment rate equations in numerical simulations of debris flows to examine the effect of topographic conditions on the flow. One-dimensional numerical simulations were performed based on the shallow water equations and three entrainment rate equations were tested. These entrainment rate equations were based on the same idea that erosion and the deposition of debris flows occur via the difference between the equilibrium and current conditions of debris flows, while they differed in the expression of the concentration, channel angle, and sediment amount. The comparison was performed using a straight channel with various channel angles and a channel with a periodically undulating surface. The three entrainment rate equations gave different amounts of channel bed degradation and hydrographs for a straight channel with a channel angle greater than 21° when water was supplied from upstream at a steady rate. The difference was caused by the expression of the entrainment rate equations. For channels with little undulation, the numerical simulations gave results almost identical to those for straight channels with the same channel angle. However, for channels with large undulations, the hydrographs differed from those for straight channels with the same channel angle when the channel angle was less than 21°. Rapid erosion occurred and the hydrograph showed a significant peak, especially in cases using the entrainment equation expressed by channel angle. This was caused by the effects of the steep undulating sections, since the effect increased with the magnitude of the undulation, suggesting that a debris flow in an upstream area develops differently according to the topographic conditions. These results also inferred that numerical simulations of debris flow can differ depending on the spatial resolution of the simulation domain, as the resolution determines the reproducibility of the undulations.

Theoretical and experimental research on influence of rotor taper on performance of cone-shape helical pumps

The structure of a rotor has full impact on the performance of cone-shaped helical pumps. Numerical simulation and experimental tests are applied to get pressure, velocity and flow of a cone-shaped helical pump, and explores flow condition of blood in artificial blood pump. Rotors with four different tapers of artificial pump are designed. The flow condition of blood at the entrance, near the front diffuser, near the rotor, near the rear diffuser and at the exit, the pressure difference between entrance and exit and flow of artificial blood pump with different taper rotors are simulated, and then the influence rules of rotor taper on the performance of cone-shaped helical pump are revealed. In order to verify the correctness of theoretical analysis, rotors with three different tapers are manufactured, physical model of artificial blood pump are built, and then the actual lift and flow of blood pump with different rotors are measured respectively. The results show that taper of rotor increases, the circumfluence of blood near the front and rear diffuser decreases, the blood flows more smoothly, the energy consumption is less, and then the guide role of blade is greater. The blood at the exit of blood pump flows along the axial direction steadily. As taper of rotor increases, the pressure difference between the entrance and exit and the flow of blood pump increase subsequently. The flow condition of blood and performance of blood pump with No.3 rotor are the best. The proposed research analyzes the influence of rotor taper on performance of blood pump quantitatively, and provides the theoretical reference for the design and improving of cone-shaped helical pump.

Unsteady Internal Flow Conditions of Mini-Centrifugal Pump with Splitter Blades

Mini centrifugal pumps having a diameter smaller than lOOmm are employed in many fields. But the design method for the mini centrifugal pump is not established because the internal flow condition for these small-sized fluid machines is not clarified and conventional theory is not suitable for small-sized pumps. Therefore, mini cen- trifugal pumps with simple structure were investigated by this research. Splitter blades were adopted in this re- search to improve the performance and the internal flow condition of mini centrifugal pump which had large blade outlet angle. The original impeller without the splitter blades and the impeller with the splitter blades were prepared for experiment. The performance tests are conducted with these rotors in order to investigate the effect of the splitter blades on performance and internal flow condition of mini centrifugal pump. On the other hand, a three dimensional unsteady numerical flow analysis was conducted to investigate the change of the internal flow according to the rotor rotation. It is clarified from the experimental results that the performance of the mini cen- trifugal pump is improved by the splitter blades. The blade-to-blade low velocity region was suppressed in the case with the splitter blades. In addition to that, the unsteady flows near the volute casing tongue were suppressed due to the splitter blades. In the present paper, the performance of the mini centrifugal pump is shown and the un- steady flow condition is clarified with the results of the numerical flow analysis. Furthermore, the effects of the splitter blades on the performance and the unsteady internal flow condition are investigated.

Unsteady Flow Condition of Contra-Rotating Small-Sized Axial Fan

Small-sized axial fans are used as air cooler for electric equipments.But there is a strong demand for higher power of fans according to the increase of quantity of heat from electric devices.Therefore,higher rotational speed design is conducted,although,it causes the deterioration of efficiency and the increase of noise.Then,the adoption of contra-rotating rotors for the small-sized axial fan is proposed for the improvement of performance.In the case of contra-rotating rotors,it is necessary to design the rotor considering the unsteady flow condition of each front and rear rotor.In the present paper,the fan performance of the contra-rotating small-sized axial fan with 100mm diameter at a designed and a partial flow rates is shown,and the unsteady flow conditions at the inlet and the outlet of each front and rear rotor are clarified with unsteady numerical results.Furthermore,the relation between the performance and the unsteady flow condition of the contra-rotating small-sized axial fan is discussed and the methods to improve the performance are considered.

Improvement of signal processing in Coriolis mass flowmeters for gas-liquid two-phase flow

As an increasingly popular flow metering technology,Coriolis mass flowmeter exhibits high measurement accuracy under single-phase flow condition and is widely used in the industry.However,under complex flow conditions,such as two-phase flow,the measurement accuracy is greatly decreased due to various factors including improper signal processing methods.In this study,three digital signal processing methods—the quadrature demodulation(QD)method,Hilbert method,and sliding discrete time Fourier transform method—are analyzed for their applications in processing sensor signals and providing measurement results under gas-liquid two-phase flow condition.Based on the analysis,specific improvements are applied to each method to deal with the signals under two-phase flow condition.For simulation,sensor signals under single-and two-phase flow conditions are established using a random walk model.The phase difference tracking performances of these three methods are evaluated in the simulation.Based on the digital signal processor,a converter program is implemented on its evaluation board.The converter program is tested under single-and two-phase flow conditions.The improved signal processing methods are evaluated in terms of the measurement accuracy and complexity.The QD algorithm has the best performance under the single-phase flow condition.Under the two-phase flow condition,the QD algorithm performs a little better in terms of the indication error and repeatability than the improved Hilbert algorithm at 160,250,and 420 kg/h flow points,whereas the Hilbert algorithm outperforms the QD algorithm at the 600 kg/h flow point.

Induced noise of impeller stuck and passive rotation state in multi-stage pump without power drive under natural flow conditions

The natural flow cooling strategy is commonly employed in modern high-speed vessels and nuclear-powered submarines. These vessels rely on the energy generated by their own speed to drive the cooling system and supply cooling water to the condenser. The circulating pump, which operates without a motor drive under natural flow conditions, is a large resistance component in the cooling system. However, it is also the primary noise source, significantly impacting the vessel’s safe operation and acoustic stealth performance. This study investigates the induced noise characteristics of a multi-stage pump under natural flow conditions by experiment, computational fluid dynamics (CFD), and acoustic finite element method. The analysis encompasses the distribution of the flow field, variations in acoustic power, spectral features of flow-induced noise, and directivity of external field radiation noise under different natural flow conditions. The results show that the acoustic power distribution is correlated with the flow field. When the impeller is stuck, the noise sources primarily concentrate in the flow separation area at the blade’s leading edge, the interface area between the impeller and the guide vane, and the flow shock area inside the guide vane. Conversely, when the impeller rotates passively, the blade wake area has a higher acoustic power. The flow noise spectrum under natural flow conditions mainly exhibits broadband and discrete characteristics. Additionally, the pump structure influences the external field radiation noise, and its directivity varies with different flow rates and characteristic frequencies. This study provides valuable insights into optimal design to reduce the noise of the circulating pump in the vessel’s natural flow cooling system. It is essential for ensuring the safe operation and acoustic stealth performance of high-speed vessels and nuclear-powered submarines.

Navigable flow condition simulation based on two-dimensional hydrodynamic parallel model

Navigable flow condition simulations can provide detailed information on water depth and velocity distribution, simulation speed is one of the key factors which influence real-time navigation. In this paper, a navigable flow condition simulation system is developed to provide useful information for waterway management and shipping safety. To improve the simulation speed of 2-D hydrodynamic model, an explicit finite volume method and Open MP are used to realize parallel computing. Two mesh schemes and two computing platforms are adopted to study the parallel model＇s performance in the Yangtze River, China. The results show that the parallel model achieves dramatic acceleration, with a maximum speedup ratio of 34.94？. The parallel model can determine the flow state of the navigable channel in about 4 min, efficiency is further improved by a flow simulation scheme database. The developed system can provide early warning information for shipping safety, allowing ships to choose better routes and navigation areas according to real-time navigable flow conditions.

Necessary and sufficient condition of C^0 flows on closed surfaces with isolated singular points having the pseudo-orbit tracing property

IN this letter we discuss the necessary and sufficient condition of C^0 flows on closed surfaces with isolated singular points having the pseudo-orbit tracing property. According to ref. [1], on a closed surface, every minimal set of a C^r(r≥2) flow is trivial, but it is possible for a C^0 flow to contain non-trivial minimal sets. Thus C^0 flows on closed surfaces are more complicated than C^r(r≥2) flows.

Local well-posedness of a multidimensional shock wave for the steady supersonic isothermal flow

In this paper, we prove the local existence, uniqueness and stability of a supersonic shock for the supersonic isothermal incoming flow past a curved cone. Major difficulties include constructing an appropriate solution and treatincg the Neumann boundary conditions and local stability condition.

Experimental hydrodynamic study of the Qiantang River tidal bore

To study the hydrodynamics of tidal bore, a physical modeling study is carried out in a rectangular flume with considera- tions of the tidal bore heights, the propagation speeds, the tidal current velocities, the front steepness, and the bore shapes. After the validation with the field observations, the experimental results are analyzed, and it is shown that： （1） the greater initial ebb velocity or the larger initial water depth impedes the tidal bore propagation, （2） the maximum bore height appears at an initial ebb velocity in the range of 0.5 m/s-l.5 m/s. （3） when the Froude number exceeds 1.2, an undular bore appears, atter it exceeds 1.3, a breaking bore occurs, and after it exceeds 1.7, the bore is broken.

Dual-targeting nanovesicles enhance specificity to dynamic tumor cells in vitro and in vivo via manipulation of αvβ3-ligand binding

The dynamic or flowing tumor cells just as leukemia cells and circulating tumor cells face a microenvironment difference from the solid tumors,and the related targeting nanomedicines are rarely reported.The existence of fluidic shear stress in blood circulation seems not favorable for the binding of ligand modified nanodrugs with their target receptor.Namely,the binding feature is very essential in this case.Herein,we utilized HSPC,PEG-DSPE,cholesterol and two avb3 ligands(RGDm7 and DT4)with different binding rates to build dual-targeting nanovesicles,in an effort to achieve a"fast-binding/slow-unbinding"function.It was demonstrated that the dual-targeting nanovesicles actualized effi-cient cellular uptake and antitumor effect in vitro both for static and dynamic tumor cells.Besides,the potency of the dual-targeting vesicles for flowing tumor cells was better than that for static tumor cells.Then,a tumor metastasis mice model and a leukemia mice model were established to detect the killing ability of the drug-loaded dual-targeting vesicles to dynamic tumor cells in vivo.The therapy efficacy of the dual-targeting system was higher than other controls including single-targeting ones.Generally,it seems possible to strengthen drug-targeting to dynamic tumor cells via the control of ligandereceptor interaction.

Landmarks in the application of electrical tomography in particle science and technology

Selected milestones in the development and use of electrical tomography in powder conveying, slurry processing and multi-phase flow are highlighted. The ability to map concentration in opaque mixtures under process-realistic conditions was a major innovation for the method and has had far reaching implications. Subsequent developments have enabled velocity information to be abstracted resulting in the ability to measure component flux and motion.

A note on a boundary condition for spouted beds

The boundary condition, zero solids pressure at the top of a particle bed of maximum spoutable height, Hm, is shown to eliminate any resort to empiricism in the derivation of the fluid velocity in the annulus of a spouted bed for which both viscous and inertial effects are taken into account. The same boundary condition fails when applied to a spouted bed for which the bed height H 〈 Hm, especially when H 〈 0.8Hm.