Lumped Parameter Mass Flow Rate and Pressure Control Characteristics Model for High-Speed Pneumatic PWM on/off Valve

Aiming at solving the problem of strong coupling characteristic of the key parameters of high-speed pneumatic pulse width modulation( PWM) on / off valve, a general lumped parameter mathematical model based on the valves time periods was well developed. With this model,the mass flow rate and dynamic pressure characteristics of constant volumes controlled by high-speed pneumatic PWM on /off valves was well described. A variable flow rate coefficient model was proposed to substitute for the constant one used in most of the prior works to investigate PWM on /off valves' dynamical pressure response, and a formula for disclosing the inherent relationship among the PWM command signal,static mass flow rate,and sonic conductance of the valve was newly derived.Finally,an extensive set of analytical experimental comparisons were implemented to verify the validity of the proposed mathematica model. With the proposed model, PWM on /off valves' characteristics,such as mass flow rate,step pressure response of the valve control system,mean pressure and ripple amplitude,not only in the linear range,but also in the nonlinear range can be wel predicted; Good agreement between measured and calculated results was obtained,which proved that the model is helpful for designing a control strategy in a closed loop control system.

袋型阻尼密封动力学特性双控制体Bulk Flow模型

为快速准确预测袋型阻尼密封泄漏特性和动力学特性,针对传统单控制体Bulk Flow模型预测精度低、无法预测交叉动力系数的问题,提出了袋型阻尼密封双控制体Bulk Flow模型和动力学特性数值预测方法,并开发了计算程序。首先,依据边界层理论,将袋型密封腔室划分为两个控制体,推导了控制体的连续性、周向动量和能量方程,引入Swamee-Jain和Takahashi方程,计算流体-壁面间和流体-流体间的周向黏性摩擦力;其次,采用牛顿-拉夫森算法和摄动分析法分别求解0阶和1阶控制方程,获得各刚度、阻尼动力特性系数;然后,通过与袋型阻尼密封泄漏量和动力特性系数的实验值、单控制体Bulk Flow模型和非定常计算流体动力学(CFD)数值结果进行比较,验证了模型和方法的准确性和可靠性;最后,研究了转子转速(10 000、15 000、20 000 r/min)和预旋比(0.067、0.724、0.997)对袋型阻尼密封动力学特性的影响。结果表明:所发展的模型和方法具有计算速度快、预测精度高(泄漏量预测误差小于6%,动力特性系数预测误差小于38%)的优点;转子转速和进口预旋的增大均会导致袋型阻尼密封有效阻尼显著减小,穿越频率显著增大,易诱发轴系失稳。

A New Device for Gas-Liquid Flow Measurements Relying on Forced Annular Flow

A new measurement device,consisting of swirling blades and capsule-shaped throttling elements,is proposed in this study to eliminate typical measurement errors caused by complex flow patterns in gas-liquid flow.The swirling blades are used to transform the complex flow pattern into a forced annular flow.Drawing on the research of existing blockage flow meters and also exploiting the single-phase flow measurement theory,a formula is introduced to measure the phase-separated flow of gas and liquid.The formula requires the pressure ratio,Lockhart-Martinelli number(L-M number),and the gas phase Froude number.The unknown parameters appearing in the formula are fitted through numerical simulation using computational fluid dynamics(CFD),which involves a comprehensive analysis of the flow field inside the device from multiple perspectives,and takes into account the influence of pressure fluctuations.Finally,the measurement model is validated through an experimental error analysis.The results demonstrate that the measurement error can be maintained within±8%for various flow patterns,including stratified flow,bubble flow,and wave flow.

Theoretical Analysis and Numerical Simulation of the Static and Dynamic Characteristics of Hydrostatic Guides Based on Progressive Mengen Flow Controller

The oil film thickness of oil hydrostatic guide with constant pressure supply based on capillary restrictor is greatly affected by load, and this kind of hydrostatic guide is usually applied to the machine tools with moderate load. The static and dynamic characteristics of the guide have been studied by using some theoretical, numerical and experimental approaches, and some methods and measures have been proposed to improve its performances. The hydrostatic guide based on progressive mengen（PM） flow controller is especially suitable for the heavy numerical control（NC） machine tools. However, few literatures about the research on the static and dynamic characteristics of the hydrostatic guides based on PM flow controller are reported. In this paper, the formulae are derived for analyzing the static and dynamic characteristics of hydrostatic guides with rectangle pockets and PM flow controller according to the theory of hydrostatic bearing. On the basis of the analysis of hydrostatic bearing with circular pocket, some equations are derived for solving the static pressure, volume pressure and squeezing pressure which influence the dynamic characteristics of hydrostatic guides with rectangle pocket. The function and the influencing factors of three pressures are clarified. The formulae of amplitude-frequency characteristics and dynamic stiffness of the hydrostatic guide system are derived. With the help of software MATLAB, programs are coded with C＋＋ language to simulate numerically the static and dynamic characteristics of the hydrostatic guide based on PM flow controller. The simulation results indicate that the sensitive oil volume between the outlet of the PM flow controller and the guide pocket has the greatest influence on the characteristics of the guide, and it should be reduced as small as possible when the field working condition is met. Choosing the oil with a greater viscosity is also helpful in improving the dynamic performance of hydrostatic guides. The research work has instructing significance for analyzing and designing the guide with PM flow controller.

Experimental Study on Surface Dielectric Barrier Discharge Plasma Actuator with Different Encapsulated Electrode Widths for Airflow Control at Atmospheric Pressure

The surface dielectric barrier discharge （SDBD） plasma actuator has shown great promise as an aerodynamic flow control device. In this paper, the encapsulated electrode width of a SDBD actuator is changed to study the airflow acceleration behavior. The effects of encapsulated electrode width on the actuator performance are experimentally investigated by measuring the dielectric layer surface potential, time-averaged ionic wind velocity and thrust force. Experimental results show that the airflow velocity and thrust force increase with the encapsulated electrode width. The results can be attributed to the distinct plasma distribution at different encapsulated electrode widths.

Effects of retrospective quality control on pressure-flow data with computer-based urodynamic systems from men with benign prostatic hyperplasia

Aim： To evaluate the effects of retrospective quality control on pressure-flow data with computer-based urodynamic systems from men with benign prostatic hyperplasia （BPH）. Methods： A total of 582 traces of pressure-flow study from 181 men with BPH was included in the study. For each trace, maximum urinary flow rate （Qmax） and detrusor pressure at Qmax （pdet.Qmax） were, respectively, read from manually smoothed and corrected uroflow and detrusor pressure curves from the computer print-outs. Obstruction coefficient, International Continence Society （ICS） and Schaefer nomograms were used to detect urethral resistance and to diagnose obstruction. The results obtained by manual reading were compared with those from computer-based systems. Results： After manual correction, Qmax underwent a consistently significant decrease by 1.2 mL/s on average （P 〈 0.001）, and had a change range of 0.5-10.4 mL/s. However, pdet.Qmax underwent inconsistently intra-individual changes after correction. The obstruction coefficient increased significantly, by an average of 0.07 （P 〈 0.05）. Using the ICS nomogram, the percentage of obstruction increased from 69.8% to 73.9%, and of the non-obstruction decreased from 8.8% to 5.3% （P 〈 0.05）. There were 11% of traces that changed the classifications using the ICS nomogram, and 28.9% that changed the grades for the Schaefer nomogram. Conclusion： Systematically significant differences in parameters from pres- sure-flow study between manual readings and computer recordings were demonstrated. Manual correction resulted in a consistently lower Q a higher urethral resistance, and an aggravating obstruction. Manual readings can correct considerable false diagnoses for obstruction. Retrospective quality control of pressure-flow data with com- puter-based systems is necessary.

Flow-rate Characteristics Measurement of Regulators Based on the Pressure Response in an Isothermal Tank

Regulators are important components in pneumatic system, and their flow-rate characteristics are the key parameters for designers. According to the correlatively international standard and national standard of China, which describe the flow-rate characteristics measurement method of pneumatic regulators, the pressure and the flow are measured point by point, and then the flow-rate characteristics curve is plotted point to point. This method has some disadvantages, such as equipment complexity, much air consumption, and low efficiency. To settle the problems presented above, this paper puts forward a new high efficient and energy saving flow-rate characteristics measurement method of regulators, which is based on the pressure response when charging and discharging to an isothermal tank without any flow meters. The measurement principle, the system and the steps are introduced. And the tracking differentiator is used for the data processing of the pressure difference. Two typical kinds of regulators were experimentally investigated, and their flow-rate characteristics curves were obtained with the new and the conventional method, respectively. Comparatively, it＇s proved that this new method is feasible because it is not only able to meet the demand of the measurement precision, but also to save energy and improve efficiency. Compared to the conventional method, the new method takes only about 1/10 amount of time and consumes about only 1/30 amount of air. Hopefully it will be able to serve as an international standard of flow-rate characteristics measurement method of regulators.

Study on Transient Flow Characteristics of Attitude Control Engine During Starting Process

Liquid bipropellant attitude control rocket engines are widely used in satellites,manned spaceships,deep space probes and other spacecraft.The performance of an attitude control engine is directly related to the lifetime,control precision and safety of a spacecraft.The study of flow characteristics of an engine transient process is important to improve its performance.In this paper,the transient flow test of a transparent test piece was carried out during the starting process of the attitude control engine.Then the transient process of the test piece was simulated and compared with the test results to verify the rationality of the simulation model.Transient flow simulation was carried out for the starting process of the real engine injector.The results show that the filling of the outer ring of the oxidant circuit is slower than that of the central collecting cavity,and the filling of the second layer of the outer ring is slower than that of the first layer.The filling process in the fuel path starts from the cooling hole near the inlet side and the fuel flows out in the circumferential direction.Installation direction has little influence on engine starting flow process in the ground state.The filling time of the engine in its vacuum state is longer than that in the ground state,the filling time of oxidizer is 31%longer than that in ground state,and the filling time of fuel is 57%longer than that in ground state.

DYNAMIC CHARACTERISTICS OF ELECTRO-HYDRAULIC PROPORTIONAL PRESSURE-FLOW HYBRID VALVE

The structure principles under the flow and pressure working conditions are studied, in order to investigate the dynamic characteristics of the electro-hydraulic proportional pressure-flow hybrid valve. According to the structure principles under the two different working conditions, the transfer functions under such conditions are derived. With the transfer functions, some structure elements that may affect its performance, are investigated, afterwards some principles of optimality and effective methods for improving the dynamic performance of the valve are proposed. The conclusions can be used to instruct engineering applications and products designing. The test results conform to the results of the theoretical analysis and simulation, which proves the correctness of the study and simulation works.

High-precision nonisothermal transient wellbore drift flow model suitable for the full flow pattern domain and full dip range

A reliable multiphase flow simulator is an important tool to improve wellbore integrity and production decision-making.To develop a multiphase flow model with high adaptability and high accuracy,we first build a multiphase flow database with 3561 groups of data and developed a drift closure relationship with stable continuity and high adaptability.Second,a high-order numerical scheme with strong fault capture ability is constructed by effectively combining MUSCL technology,van Albada slope limiter and AUSMV numerical scheme.Finally,the energy equation is coupled into the AUSMV numerical scheme of the drift flow model in the form of finite difference.A transient non-isothermal wellbore multiphase flow model with wide applicability is formed by integrating the three technologies,and the effects of various factors on the calculation accuracy are studied.The accuracy of the simulator is verified by comparing the measurement results with the blowout experiment of a full-scale experimental well.

RESEARCH ON THE PERFORMANCE OF NEW TYPE OF PROPORTIONAL PESSURE AND FLOW CONTROL VALVE

A new closed loop flow controlling principle through correcting the valve'sopening area while load pressure is changing is carried out. Further more a principle using only oneproportional valve to compound control pressure and flow is suggested. By using very simpleproportional throttle valve in structure, the functions that five kinds of proportional valves orany two of them combined possess can be complimented. After analyzing, comparing, and testing thedynamic and static characteristics of valve with different controlling principles and main valvestructure styles, the optimized structure styles and control methods are achieved.

Numerical Investigation of Electrohydrodynamic (EHD) Flow Control in an S-Shaped Duct

An electrohydrodynamic （EHD） method, which is based on glow discharge plasma, is presented for flow control in an S-shaped duct. The research subject is an expanding channel with a constant width and a rectangular cross section. An equivalent divergence angle and basic function are introduced to build the three-dimensional model. Subsequently, the plasma physical models are simplified as the effects of electrical body force and work （done by the force） on the fluid near the wall. With the aid of FLUENT software, the source terms of momentum and energy are added to the Navier-Stokes equation. Finally, the original performance of three models （A, B and C） is studied, in which model A demonstrates better performance. Then EHD control based on model A is discussed. The results show that the EHD method is an effective way of reducing flow loss and improving uniformity at the duct exit. The innovation in this study is the assessment of the EHD control effect on the flow in an S-shaped duct. Both the parametric modeling of the S-shaped duct and the simplified models of plasma provide valuable information for future research on aircraft inlet ducts.

Flow Characteristics of Grains in a Conical Silo with a Central Decompression Tube Based on Experiments and DEM Simulations

Grains are widely present in industrial productions and processing,and are stored in silos.In the silo,auxiliary structures are added to achieve efficient production.However,little effort has been devoted to the influence of the internal structure of the silo on the granular flow.In this work,a silo with a central decompression tube is studied through experimental measurements and discrete element methods.Then,the influences of the central decompression tube on the flow behavior of grains and wall pressure are analyzed.Results show that the grains are in mass flow in the silo without a central decompression tube,while the grains are in funnel flow in the silo with a central decompression tube.Moreover,regardless of whether there is a central decompression tube in the silo,the maximum pressure appears at the top of the conical silo.In the lower part of the silo,the wall pressure of the silo with a central decompression tube is lower than that of the silo without a central decompression tube.Therefore,a silo with a central decompression tube is more conducive to grain storage and discharge than a silo without a central decompression tube.

Numerical Simulation and Experimental Analysis of the Influence of Asymmetric Pressure Conditions on the Splitting of a Gas-Liquid Two-Phase Flow at a T-Junction

Dedicated experiments and numerical simulations have been conducted to investigate the splitting characteristics of a gas-liquid two phase flow at a T junction.The experiments were carried out for different gas-liquid velocities.The flow rates in the two branches were measured accurately to determine how the two considered phases distribute in the two outlets.The experimental results have shown that when the two outlet pressures are asymmetric,the two-phase flow always tends to flow into the outlet which has a lower pressure.As the inlet liquid velocity increases,however,the two-phase flow gradually tends to split evenly.Compared with the experiment results,the pressure difference between the two outlets can be determined more accurately by means of numerical simulation.The trends of experimental results and simulations are in very good agreement.

Formation and evolution of gas flow channels in the abutment pressure area

The permeability of coal ahead of the working face obviously changes dues to changes in abutment pressure.The formation and evolution of gas flow channels within the abutment pressure area was studied by analyzing the fracture extension mechanism and fracture development in different zones of the abutment pressure area.Fracture and damage mechanics theory is used to understand the observations.The following two techniques were used to understand the evolution of gas flow channels:field observation of the characteristic fractures at different positions relative to the working face and fluorescence micrographs of prepared coal samples.Bending tensile fractures develop along an approximately vertical direction that forms a microscopic network of channels in areas of stress concentration.The abutment pressure affects the local stress and,hence,the local gas conduction.The fractures induced by large deformation and plastic flow form macroscopically networked channels in the reduced stress area.Closer to the working face the gas flow channels evolve from microscopic to macroscopic and from isolated to network.Gas permeability continuously increases during this time.This is corroborated by field observations of the displacement of top coal and the gas flow from gas extraction drillings.

Experimental Study on the Flow Characteristics of a Plate with a Mechanically Choked Orifice

The mechanically choked orifice plate (MCOP) is a new type of device for flow control by which choking conditionsfor incompressible fluids can be obtained with relatively small pressure losses. Given the lack of relevant results anddata in the literature, in the present study, we concentrate on the experimental determination of the flow coefficientfor the annular orifice, the pressure distribution in the MCOP, and the characteristics of the choked flow itself. Asconfirmed by the experimental results, the Reynolds number, the orifice plate thickness, the plug taper, and theeccentricity have an obvious influence on the aforementioned flow coefficient. The pressure drop in the MCOPis mainly generated near the orifice plate, and the pressure upstream of the orifice plate is slightly reduced in theflow direction, while the pressure downstream of the orifice plate displays a recovery trend. The choked flow rateof the MCOP can be adjusted by replacing the spring with a maximum flow control deviation of 4.91%.

Experimental research on characteristic of start-up pressure wave propagation in gelled crude oil by large-scale flow loop

In order to research start-up pressure wave propagation mechanism and determine pressure wave speed in gelled crude oil pipelines accurately,experiment of Large-scale flow loop was carried out.In the experiment,start-up pressure wave speeds under various operation conditions were measured,and effects of correlative factors on pressure wave were analyzed.The experimental and theoretical analysis shows that thermal shrinkage and structural properties of gelled crude oils are key factors influencing on start-up pressure wave propagation.The quantitative analysis for these effects can be done by using volume expansion coefficient and structural property parameter of gelled crude oil.A new calculation model of pressure wave speed was developed on the basis of Large-scale flow loop experiment and theoretical analysis.

Numerical Analysis of a Microjet-Based Method for Active Flow Control in Convergent-Divergent Nozzles with a Sudden Expansion

A method based on microjets is implemented to control the flow properties in a convergent-divergent nozzle undergoing a sudden expansion.Three different variants of this active control technique are explored numerically by means of a finite-volume method for compressible fluid flow:with the first one,the control is implemented at the base,with the second at the wall,while the third one may be regarded as a combination of these.When jets are over-expanded,the control is not very effective.However,when a favourable pressure gradient is established in the nozzle,the control becomes effective,leading to an increase in the base pressure.

CFD Analysis of Flow Characteristics of Corrugated Louvered Fins at Low Reynolds

A 2-D laminar flow model was established for CFD analysis of air-flow between louvered fins. Two louvered fins are studied based on commercial software FLUENT. Air-flow pressure drop characteristics are derived on the calculation of Reynolds number from 75.3 to 600. The numerical results are in good agreement with the experimental data when Reynolds is lower.

Evolution and controlling factors of the gravity flow deposits in the Miocene sequence stratigraphic framework,the Lower Congo-Congo Fan Basin,West Africa

To understand the evolution of the Miocene gravity flow deposits in the Lower Congo-Congo Fan Basin,this paper documents the Miocene sequence stratigraphic framework,the depositional characteristics and the controlling factors of the gravity flow system.Based on the establishment of high-resolution sequence stratigraphic framework,lithofacies characteristics and sedimentary units of the gravity flow deposits in the region are identified by using seismic,well logging and core data comprehensively,and the sedimentary evolution process is revealed and the controlling factors are discussed.The Miocene can be divided into four 3 rd-order sequences(SQ1-SQ4).The gravity flow deposits mainly include siliciclastic rock and pelite.The main sedimentary units include slumping deposits,mass transport deposits(MTD),channel fills,levee-overbank deposits,and frontal lobes.In the Early Miocene(SQ1),mainly gull-wing,weakly restricted to unrestricted depositional channel-overbank complexes and lobes were formed.In the early Middle Miocene(SQ2),W-shaped and weakly restricted erosional-depositional channels(multi-phase superposition)were subsequently developed.In the late Middle Miocene(SQ3),primarily U-shaped and restricted erosional channels were developed.In the Late Miocene(SQ4),largely V-shaped and deeply erosional isolated channels were formed in the study area.Climate cooling and continuous fall of the sea level made the study area change from toe of slope-submarine plain to lower continental slope,middle continental slope and finally to upper continental slope,which in turn affected the strength of the gravity flow.The three times of tectonic uplifting and climate cooling in the West African coast provided abundant sediment supply for the development of gravity flow deposits.Multistage activities of salt structures played important roles in redirecting,restricting,blocking and destroying the gravity flow deposits.Clarifying the characteristics,evolution and controlling factors of the Miocene gravity flow deposits in the Lower Congo-Congo Fan Basin can provide reference for deep-water petroleum exploration in this basin.