Foam diversion can effectively solve the problem of uneven distribution of acid in layers of different permeabilities during matrix acidizing. Based on gas trapping theory and the mass conservation equation, mathemati...Foam diversion can effectively solve the problem of uneven distribution of acid in layers of different permeabilities during matrix acidizing. Based on gas trapping theory and the mass conservation equation, mathematical models were developed for foam-diverted acidizing, which can be achieved by a foam slug followed by acid injection or by continuous injection of foamed acid. The design method for foam-diverted acidizing was also given. The mathematical models were solved by a computer program. Computed results show that the total formation skin factor, wellhead pressure and bottomhole pressure increase with foam injection, but decrease with acid injection. Volume flow rate in a highpermeability layer decreases, while that in a low-permeability layer increases, thus diverting acid to the low-permeability layer from the high-permeability layer. Under the same formation conditions, for foamed acid treatment the operation was longer, and wellhead and bottomhole pressures are higher. Field application shows that foam slug can effectively block high permeability layers, and improve intake profile noticeably.展开更多
In order to increase the specific energy and specific power of a lead-acid battery, lead foam grid was prepared by electrodepositing Pb-Sn alloy on a copper foam substrate and used as negative current collector for a ...In order to increase the specific energy and specific power of a lead-acid battery, lead foam grid was prepared by electrodepositing Pb-Sn alloy on a copper foam substrate and used as negative current collector for a lead acid battery whose capacity was limited by the negative plate. Comparing the effect of the cast grid, under the same conditions, the mass of lead foam grid decreases by 35%, and the area of lead foam contacted with active material increases by about 20 times. Under 2 h rate discharge condition, with a high current （3 0 I2） e and low-temperature （-10 ℃, I2） discharge system, the lead foam grid markedly boosts the discharge performance of lead acid battery. It increases not only the negative electrode mass specific capacity by 27%,37% and 29%,but also the utilization efficiency of the negative active material by 5%. Compared with the negative electrode of cast grid, XRD and SEM results show that after 20 cycles at the state of charge, the sponge lead in the negative lead foam electrode has smaller crystals and less PbSO4 on its surface. Meanwhile, at the state of full discharge, the PbSO4 crystals are smaller and occur less on the surface of lead foam electrode. This indicates its active material reacts more uniformly.展开更多
文摘Foam diversion can effectively solve the problem of uneven distribution of acid in layers of different permeabilities during matrix acidizing. Based on gas trapping theory and the mass conservation equation, mathematical models were developed for foam-diverted acidizing, which can be achieved by a foam slug followed by acid injection or by continuous injection of foamed acid. The design method for foam-diverted acidizing was also given. The mathematical models were solved by a computer program. Computed results show that the total formation skin factor, wellhead pressure and bottomhole pressure increase with foam injection, but decrease with acid injection. Volume flow rate in a highpermeability layer decreases, while that in a low-permeability layer increases, thus diverting acid to the low-permeability layer from the high-permeability layer. Under the same formation conditions, for foamed acid treatment the operation was longer, and wellhead and bottomhole pressures are higher. Field application shows that foam slug can effectively block high permeability layers, and improve intake profile noticeably.
文摘In order to increase the specific energy and specific power of a lead-acid battery, lead foam grid was prepared by electrodepositing Pb-Sn alloy on a copper foam substrate and used as negative current collector for a lead acid battery whose capacity was limited by the negative plate. Comparing the effect of the cast grid, under the same conditions, the mass of lead foam grid decreases by 35%, and the area of lead foam contacted with active material increases by about 20 times. Under 2 h rate discharge condition, with a high current （3 0 I2） e and low-temperature （-10 ℃, I2） discharge system, the lead foam grid markedly boosts the discharge performance of lead acid battery. It increases not only the negative electrode mass specific capacity by 27%,37% and 29%,but also the utilization efficiency of the negative active material by 5%. Compared with the negative electrode of cast grid, XRD and SEM results show that after 20 cycles at the state of charge, the sponge lead in the negative lead foam electrode has smaller crystals and less PbSO4 on its surface. Meanwhile, at the state of full discharge, the PbSO4 crystals are smaller and occur less on the surface of lead foam electrode. This indicates its active material reacts more uniformly.
