Repair of Second-Generation Recycled Fine Aggregate of Waste Concrete from Freeze-Thaw Environment by Carbonation Treatment

The reuse of waste recycled concrete from harsh environments has become a research hotspot in the field of construction.This study investigated the repair effect of carbonation treatment on second-generation recycled fine aggregate(SRFA)obtained from recycled fine aggregate concrete(RFAC)subjected to freeze-thaw(FT)cycles.Before and after carbonation,the properties of SRFA were evaluated.Carbonated second-generation recycled fine aggregate(CSRFA)at five substitution rates(0%,25%,50%,75%,100%)to replace SRFA was used to prepare carbonated second-generation recycled fine aggregate concrete(CSRFAC).The water absorption,porosity and mechanical properties of CSRFAC were tested,and its frost-resisting durability was evaluated.The results showed after carbonation treatment,the physical properties of SRFA was improved and met the requirements of II aggregate.The micro-hardness of the interfacial transition zone and attached mortar in CSRFA was 50.5%and 31.2%higher than that in SRFA,respectively.With the increase of CSRFA replacement rate,the water absorption and porosity of CSRFAC gradually decreased,and the mechanical properties and frost resistance of CSRFAC were gradually improved.Carbonation treatment effectively repairs the damage of SRFA caused by FT cycles and improves its application potential.

Coupling Effect of Cryogenic Freeze-Thaw Cycles and Chloride Ion Erosion Effect in Pre-Cracked Reinforced Concrete

Chloride (Cl−) ion erosion effects can seriously impact the safety and service life of marine liquefied natural gas(LNG) storage tanks and other polar offshore structures. This study investigates the impact of different low-temperaturecycles (20°C, –80°C, and −160°C) and concrete specimen crack widths (0, 0.3, and 0.6 mm) on the Cl−ion diffusion performance through rapid erosion tests conducted on pre-cracked concrete. The results show thatthe minimum temperature and crack width of freeze-thaw cycles enhance the erosive effect of chloride ions. TheCl− ion concentration and growth rate increased with the increasing crack width. Based on the experimental modeland in accordance with Fick’s second law of diffusion, the Cl− ion diffusion equation was modified by introducingcorrection factors in consideration of the freeze-thaw temperature, crack width, and their coupling effect.The experimental and fitting results obtained from this model can provide excellent reference for practical engineeringapplications.

NMR research on deterioration characteristics of microscopic structure of sandstones in freeze-thaw cycles

In order to study the deterioration characteristics of the microscopic structure of sandstones in freeze-thaw cycles, tests of180 freeze-thaw cycles were performed on sandstone specimens. The nuclear magnetic resonance （NMR） technique was applied tothe measurement of sandstone specimens and analysis of the magnetic resonance imaging. Then, the fractal theory was employed tocompute the fractal dimension values of pore development of rocks after different freeze-thaw cycles. The results show that the massand porosity of rocks grow with the increase of freeze-thaw cycles. According to the NMR T2 distribution of sandstones, the poresizes of rock specimens increase after 180 freeze-thaw cycles, especially that of the medium-sized and small-sized pores. The spatialdistribution of sandstone pores after freeze-thaw cycles has fractal features within certain range, and the fractal dimension ofsandstones tends to increase gradually.

Effects of freeze-thaw cycles on fracture behavior of epoxy asphalt concrete

According to the winter temperature of Peking,the freeze-thaw（FT） condition in laboratory was determined.Seven groups of epoxy asphalt concrete（EAC） specimen were exposed to different FT cycles.The flexural modulus and fracture energy（G_F） of EAC exposed to different FT cycles were obtained through the 3-point bending test.Meanwhile,the plane strain fracture toughness（K_（IC）） of EAC was obtained through numerical simulation.The results show that the flexural modulus of the FT conditioned EAC samples decreases with the increase of FT cycles.The FT damage of flexural modulus is 60%after 30 FT cycles.Nevertheless,with the increase of FT cycles,the G_F and K_（IC） of EAC decrease first and then increase after 15 FT cycles.

Ultimate load bearing capacity evaluation of concrete beams subjected to freeze-thaw cycles

A theoretical prediction method based on the change of concrete material is proposed to evaluate the ultimate bending moment of concrete beams which have undergone freeze-thaw cycles （PTCs）. First, the freeze-thaw damage on concrete material is analyzed and the residual compressive strength is chosen to indicate the freeze-thaw damage. Then, the equivalent block method is employed to simplify the compressive stress-strain curve of the freeze-thaw damaged concrete and the mathematical expression for the ultimate bending moment is obtained. Comparisons of the predicted results with the test data indicate that the ultimate bending moment of concrete beams affected by FTC attack can be predicted by this proposed method. However, the bond-slip behavior and the randomness of freeze-thaw damage will affect the accuracy of the predicted results, especially when the residual compressive strength is less than 50%.

Determination of Optimum Conditions for Cell-wall Destruction of Auricularia auricula Mycelia under the Synergistic Effect of Ultrasonic Waves and Repeated Freeze-thaw Cycles

We aimed to investigate the synergistic effects of ultrasonic waves and repeated freeze-thaw cycles on cel-wal destruction of Auricularia auric-ula mycelia, and determine the best combination of conditions for cel-wal destruc-tion of Auricularia auricula mycelia. [Method] The effects of destruction time, added water, destruction times, freeze time and number of freeze-thaw cycles during ultra-sonic treatment on polysaccharide yield were investigated by single-factor test in our research. The optimum conditions for cel-wal destruction of Auricularia auricula mycelia by the synergistic effect of ultrasonic waves and repeated freeze-thaw cycles were ascertained by orthogonal test. [Result] The results of single test indicated the best combination of conditions was as fol ows： freeze time, 30 min; destruction time, 20 min; added water, 15 times; destruction times, 2 times; number of freeze-thaw cycles, 3 cycles. The results of orthogonal test indicated the influencing factors ranked as destruction time 〉 destruction times 〉 freeze time. The best combination of conditions was as fol ows： freeze time, 30 min; destruction time, 25 min; destruc-tion times, 2 times. Under above conditions, the polysaccharide yield reached 57.76 mg/g. [Conclusion] This research would provide a basis and reference for practical production.

Dynamic behaviors of water-saturated and frozen sandstone subjected to freeze-thaw cycles

In high-altitude cold areas,freeze-thaw(F-T)cycles induced by day-night and seasonal temperature changes cause numerous rock mass slope engineering disasters.To investigate the dynamic properties of rock in the natural environment of a high-altitude cold area,standard specimens were drilled from the slope of the Jiama copper mine in Tibet,and dynamic compression tests were performed on watersaturated and frozen sandstone with different numbers of F-T cycles(0,10,20,30,and 40)by the split Hopkinson pressure bar(SHPB)system with a cryogenic control system.The influence of water-saturated and frozen conditions on the dynamic performance of sandstone was investigated.The following conclusions are drawn:(1)With increasing strain rate,the attenuation factor(la)of water-saturated sandstone and the intensifying factor(li)of frozen sandstone linearly increase.As the number of F-T cycles increases,the dependence factor(ld)of water-saturated sandstone linearly decreases,whereas the ld of frozen sandstone linearly increases.(2)The prediction equation of the dynamic compressive strength of water-saturated and frozen sandstone is obtained,which can be used to predict the dynamic compressive strength of sandstone after various F-T cycles based on the strain rate.(3)The mesoscopic mechanism of water-saturated and frozen sandstone’s dynamic compressive strength evolution is investigated.The water softening effect causes the dynamic compressive strength of water-saturated sandstone to decrease,whereas the strengthening effect of pore ice causes it to increase.(4)The decrease in the relative dynamic compressive strength of water-saturated sandstone and the increase in the relative dynamic compressive strength of frozen sandstone can be attributed to the increased porosity.

Effect of Freeze-Thaw Cycles on Mechanical Properties and Permeability of Red Sandstone under Triaxial Compression

Geological disasters will happen in cold regions because of the effects of freeze-thaw cycles on rocks or soils, so studying the effects of these cycles on the mechanical characteristics and permeability properties of rocks is very important. In this study, red sandstone samples were frozen and thawed with o, 4, 8 and 12 cycles, each cycle including 12 h of freezing and 12 h of thawing. The P-wave velocities of these samples were measured, and the mechanical properties and evolution of the steady-state permeabilities were investigated in a series of uniaxial and triaxial compression tests. Experimental results show that, with the increasing of cyclic freeze-thaw times, the P-wave velocity of the red sandstone decreases. The number of freeze-thaw cycles has a significant influence on the uniaxial compressive strength, elastic modulus, cohesion, and angle of internal friction. The evolution of permeability of the rock samples after cycles of freeze-thaw in a complete stress-strain process under triaxial compression is closely related to the variation of the microstructure in the rock. There is a highly corresponding relationship between volumetric strain and permeability with axial strain in all stages of the stress-strain behaviour.

Effects of freeze-thaw cycle on engineering properties of loess used as road fills in seasonally frozen ground regions,North China

Compacted loess is widely used as fills of road embankments in loess regions of northern China.Generally, densely-compacted loess can satisfy the requirements of embankment strength and postconstruction deformation. However, uneven subsidence, pavement cracks and other related damages can affect the integrity of loess subgrade after several years of operation,and even cause some hazards, especially in North China, where the strong freeze-thaw erosion occurs. In this study, cyclic freeze-thaw tests for both densely and loosely compacted loess samples were performed to determine the variation in engineering properties such as volume, void ratio, collapsible settlement,microstructure, and the related mechanisms were addressed. The experimental results showed that an obvious water migration and redistribution occurred within the samples during freeze-thaw cycles. Ice lenses and fissures could be identified in the upper frozen layers of the samples. After freeze-thaw cycles,the dry densities of the upper layers of samples changed significantly due to strong freeze-thaw erosion. The dry densities decreased for the dense sample and increased for the loose sample. It can be found that dense samples become loose, while loose samples became dense with the increasing number of freeze-thaw cycles. Their related void ratios changed reversely. Both void ratios tended to fall into a certain range, which verified the concept of a residual void ratio proposed by Viklander. The loosening process of densely compacted samples involves the formation of large pores, volume increase and density reduction as well as the related changes in mechanical properties because freeze-thaw cycles may be important contribution to problems of loess road embankments.Adverse effects of freeze-thaw cycles, therefore,should be taken into account in selecting loess parameters for the stability evaluation of road embankment in seasonally frozen ground regions.

Damage mechanism of soil-rock mixture after freeze-thaw cycles

As a widely distributed geological and engineering material,the soil-rock mixture always undergoes frequentative and short-term freeze-thaw cycles in some regions.Its internal structure is destroyed seriously,but the damage mechanism is not clear.Based on the damage factor,the damage research of properties of soil-rock mixture after different times of freeze-thaw cycles is investigated.Firstly,the size-distributed subgrade gravelly soil samples are prepared and undergo different times of freeze-thaw cycles periodically(0,3,6,10),and indoor large-scale triaxial tests are completed.Secondly,the degradation degree of elastic modulus is considered as a damage factor,and applied to macro damage analysis of soil-rock mixture.Finally,the mesoscopic simulation of the experiments is achieved by PFC3D,and the influence on strength between soil-rock particles caused by freeze-thaw cycles is analyzed.The results show that freeze-thaw cycles cause internal damage of samples by weakening the strength between mesoscopic soil-rock particles,and ultimately affect the macro properties.After freeze-thaw cycles,on the macro-scale,elastic modulus and shear strength of soil-rock mixture both decrease,and the decreasing degree is related to the times of cycles with the mathmatical quadratic form;on the meso-scale,freeze-thaw cycles mainly cause the degradation of the strength between soil-rock particles whose properties are different significantly.

Experimental studies on the pore structure and mechanical properties of anhydrite rock under freeze-thaw cycles

To study the deterioration mechanisms of anhydrite rock under the freeze-thaw weathering process,the physico-mechanical characteristics and microstructure evolutions of anhydrite samples were determined by a series of laboratory tests.Then,a descriptive-behavioral model was used to measure the integrity loss in anhydrite samples caused by cyclic freeze-thaw.Finally,the freeze-thaw damage mechanisms of anhydrite rock were revealed from the macro and micro aspects.The results show that the pore size of the anhydrite rock is mainly concentrated in the range of 0.001-10μm.As the number of freeze-thaw cycles increases,there is a growth in the proportion of macropores and mesopores.However,the proportion of micropores shows a declining trend.The relations of the uniaxial compressive strength,triaxial compressive strength,cohesion,and elastic modulus versus freeze-thaw cycles can be fitted by a decreasing exponential function,while the internal friction angle is basically unchanged with freezethaw cycles.With the increase of confining pressure,the disintegration rates of the compressive strength and the elastic modulus decrease,and the corresponding half-life values increase,which reveals that the increase of confining pressures could inhibit freeze-thaw damage to rocks.Moreover,it has been proven that the water chemical softening mechanism plays an essential role in the freeze-thaw damage to anhydrite rock.Furtherly,it is concluded that the freeze-thaw weathering process significantly influences the macroscopic and microscopic damages of anhydrite rock.

Deterioration Mechanism of Sulfate Attack on Concrete under Freeze-thaw Cycles

The experiments of concrete attacked by sulfate solution under freeze-thaw cycles were investigated. The sulfate solution includes two types of 5% Na2SO4 and 5% MgSO4. Through the experiment, microstructural analyses such as SEM, XRD and TGA measurements were performed on the selected samples after freeze-thaw cycles. The corrosion products of the concrete were distinguished and quantitatively compared by the thermal analysis. Besides, the damage mechanism considering the dynamic modulus of elastically of concrete under the coupling effect was also investigated. The experimental results show that, under the action of freeze-thaw cycles and sulfate attack, the main attack products in concrete are ettringite and gypsum. The corrosion products exposed to MgSO4 solution are more than those to Na2SO4 solution. Furthermore, the content of gypsum in concrete is less than that of ettringite in test, and some of gypsum can be observed only after a certain corrosion extent. It is also shown that MgSO4 solution has a promoting effect to the damage of concrete under freeze-thaw cycles. Whereas for Na：SO4 solution, the damage of concrete has restrained before 300 freeze-thaw cycles, but the sulfate attack accelerates the deterioration process in its further test period.

Effect of Freeze-thaw Cycles on Bond Strength between Steel Bars and Concrete

The effect of freezing and thawing cycles on mechanical properties of concrete （compressive, splitting tensile strength） was experimentally investigated. According to the pullout test data of three kinds of deformed steel bars, the bond stress-slip curves after freezing and thawing were obtained. The empirical equations of peak bond strength were proposed that the damage accounted for effects of freezing and thawing cycle. Meanwhile, the mechanism of bond deterioration between steel bars and concrete after freezing and thawing cycles was discussed. All these conclusions will be useful to the durability design and reliability calculation of RC structures in cold region.

Shear behavior of ultrafine magnetite tailings subjected to freeze-thaw cycles

To study the shear behavior of the ultrafine magnetite tailings subjected to freeze-thaw cycles,unconsolidated-undrained shear tests were conducted on ultrafine-grained tailings that were subjected to 1-11 cycles of freeze-thaw and defined as a type of clayey silt under confining pressures of 100,200,and 300 kPa.Taking the number of freeze-thaw cycles,cooling temperature,initial dry density,and moisture content as the four main influencing factors of shear behavior of the tailings samples,the shear stress-strain curve,compression modulus,failure strength,cohesion,and internal friction angle were measured.The results show that the freeze-thaw cycle has an obvious weakening effect on the shear behavior of the tailings material,and the shear mechanical parameters are affected by a combination of confining pressure,freeze-thaw cycle condition,and initial physical-mechanical properties of the tailings samples.Through the microstructural analysis of the tailings samples subjected to freeze-thaw cycles,it shows that the freeze-thaw cycle mainly affects the porosity,bound water,and arrangement of the tailings particles.Subsequently,the macroscopic changes in shear strength indexes emerge,and then the stability of the tailings dam will decrease.

BEHAVIOR OF AIR-ENTRAINED CONCRETE AFTER FREEZE-THAW CYCLES

The experimental study of air-entrained concrete specimens subjected to different cycles of freeze-thaw was completed. The dynamic modulus of elasticity, weight loss, the cubic compressive strength, compressive strength, tensile strength and cleavage strength of air-entrained concrete were measured after 0, 100, 200, 300, 400 cycles of freeze-thaw. The experimental results showed that the dynamic modulus of elasticity and strength decreased as the freeze-thaw was repeated. The influences of freeze-thaw cycles on the mechanical properties, the dynamic modulus of elasticity and weight loss were analyzed according to the experimental results. It can serve as a reference for the maintenance, design and the life prediction of dams, hydraulic structures, offshore structures, concrete roads and bridges in northern cold regions.

The influence of freeze-thaw cycles on the granulometric composition of Moscow morainic clay

The freeze-thaw cycling process considerably changes the composition, structure, and properties of soils. Since the grain size is the most important factor in determining soil characteristics, our current research primarily aims to investigate dynamic changes of the soil fraction when exposed to freeze-thaw conditions. We observed two series of Moscow morainic clayey specimens （gQⅡm）： （Ⅰ） the original series, and （Ⅱ） the remolded series. We subjected each series of soil specimens to different frequencies of freeze-thaw cycles （3, 6, 20, and 40 cycles）, and we used granulometric tests to analyze both series before and after exposure to freeze-thaw conditions. As a result of our experiments, the granulometric compositions tended to be distributed evenly after 40 freeze-thaw processes （i.e., content of fraction for 0.1-0.05 mm was increased after 40 freeze-thaw cycles） because the division of coarse grains and the aggregation of fine grains were synchronized during the freeze-thaw process. The soil grains in both series changed bi-directionally. In the original series, changes of the sand grains were conjugated with the clay grains, and in the remolded series, changes of the sand grains were conjugated with the silt grains, because potential energy difference caused the division and aggregation processes to relate to the counteraction process. The even distribution of soil grain size indicated the state of equilibrium or balance. The granulometric compositions were altered the most during the sixth freeze-thaw cycle, because the coefficient of the intensity variation of the grain fineness （Kvar） had its maximum value at that time.

Review of the influence of freeze-thaw cycles on the physical and mechanical properties of soil

Seasonally frozen soil is a four-phase material and its physical-mechanical properties are more complex compared to the unfrozen soil. Its physical properties changes during the freeze-thaw process; repeated fieeze-thaw cycles change the characteristics of soil, which can render the soil from an unstable state to a new dynamic equilibrium state. The freezing process changes the structttre coupled between the soil particle arrangements, which will change the mechanical properties of the soil. The method of significance and interaction between different fac tors should be considered to measure the influence on the propties of soil under freeze-thaw cycles.

Dynamic fracture properties and criterion of cyclic freeze-thaw treated granite subjected to mixed-mode loading

Rock masses in high-elevation or cold regions are vulnerable to the combined effects of freeze-thaw(F-T)weathering and dynamic mixed-mode loading,posing a serious threaten to the safety and stability of geotechnical engineering.In this study,a series of dynamic fracture tests were conducted on notched semi-circular bend(NSCB)granite specimens subjected to different mixed-mode loading and F-T cycles using a split Hopkinson pressure bar(SHPB)test system.The effects of F-T treatment and dynamic mixed-mode loading on the fracture properties of granite,including effective fracture toughness,progressive fracture process,and macroscopic morphology of fracture surface,were comprehensively revealed.The experimental results suggest that the dynamic effective fracture toughness of NSCB specimens is dependent on the loading rate,particularly when the mode I loading is dominant.Additionally,the fracture toughness decreases as the number of F-T cycles increases,with an inflection point at 30 F-T cycles.All granite specimens subjected to mixed-mode loading exhibit a curved fracture path,with faster crack propagation speed and more fine cracks in specimens exposed to higher F-T cycles.Macroscopic morphology of fracture surface obtained using three-dimensional(3D)scanning indicates that the fractal dimension of the fracture surface increases with increasing F-T cycles,and the increment is more pronounced for specimens subjected to a higher mode II loading component.Moreover,this study compared the fracture resistance of F-T treated granite subjected to dynamic mixed loading using the maximum tangential stress(MTS)criterion and the generalized maximum tangential stress-based semi-analytical(SA-GMTS)criterion.Compared with the MTS criterion,the SA-GMTS criterion shows a more reasonable consistency with the experimental results,with a root mean square error within±7%.

Acoustic experimental study of two types of rock from the Tibetan Plateau under the condition of freeze-thaw cycles

Under the condition of freeze-thaw cycles, two types of rocks （granite and andesite）, used as slope protection for the Qinghai-Tibet Railway, were tested according to the special climatic conditions in the Tibetan Plateau, and their various damage processes in ap- pearance were carefully observed. Observation results show that damage of andesite was more serious than that of granite. Using an acoustic instrument, ultrasonic velocity was tested. The changing trends of velocity with the number of freeze-thaw cycles were analyzed, and the freeze-thaw cycle damaging the physical and mechanical properties of rocks can be seen. According to the changing trends of ultrasonic velocity with the number of freeze-thaw cycles, mechanical parameters of rocks, such as dynamic elasticity modulus, Poisson＇s ratio, and dynamic bulk modulus were analyzed. It is found that they all have declining trends as the number of fi＇eeze-thaw cycles increases, and in particular, when the cycle number reaches a certain extent, the Poisson＇s ratio of rocks begins to become negative.

Effect of freeze-thaw cycles on soil engineering properties of reservoir bank slopes at the northern foot of Tianshan Mountain

The instability of soil bank slopes induced by freeze-thaw cycles at the northern foot of Tianshan Mountain is very common.The failure not only caused a large amount of soil erosion,but also led to serious reservoir sedimentation and water quality degradation,which exerted a lot of adverse effects on agricultural production in the local irrigation areas.Based on field investigations on dozens of irrigation reservoirs there,laboratory tests were carried out to quantitatively analyze the freeze-thaw effect on the soil engineering characteristics to reveal the facilitation on the bank slope instability.The results show that the softening characteristics of the stressstrain curves gradually weaken,the effective cohesions decline exponentially,the seepage coefficients enlarge,and the thermal conductivities decrease after 7 freeze-thaw cycles.The freeze-thaw effect on the specimens with low confining pressures,low dry densities and high water contents is more significant.The water migration and the phase transition between water and ice result in the variations of the soil internal microstructures,which is the main factor affecting the soil engineering characteristics.Sufficient water supply and the alternation of positive and negative temperatures at the reservoir bank slopes in cold regions make the water migration and phase transition in the soil very intensely.It is easy to form a large number of pores and micro cracks in the soil freezing and thawing areas.The volume changes of the soil and the water migration are difficult to reach a dynamic balance in the open system.Long-term freeze-thaw cycles will bring out the fragmentation of the soil particles,resulting in that the micro cracks on the soil surfaces are developing continuously.The soil of the bank slopes will fall or collapse when these cracks penetrate,which often happens in winter there.