Velocity compensation methods for LPRF modulated frequency stepped-frequency(MFSF) radar

In the high speed target environment,there exists serious Doppler effect in the low pulse repetition frequency（LPRF） modulated frequency stepped frequency（MFSF） radar signal.The velocity range of the target is large and the velocity is high ambiguous,so the single method is difficult to satisfy the velocity measurement requirement.For this problem,a novel method is presented,it is a combination of cross-correlation inner frame velocity measurement and range-Doppler coupling velocity measurement.The cross-correlation inner frame method,overcoming the low Doppler tolerance of the cross-correlation between frames,can obtain the coarse velocity of the high speed target,and then the precision velocity can be obtained with the range-Doppler coupling method.The simulation results confirm the method is effective,and also it is well real-time and easy to the project application.

Modified Omega-K algorithm for processing helicopter-borne frequency modulated continuous waveform rotating synthetic aperture radar data

With appropriate geometry configuration, helicopter- borne rotating synthetic aperture radar （ROSAR） can break through the limitations of monostatic synthetic aperture radar （SAR） on forward-looking imaging. With this capability, ROSAR has extensive potential applications, such as self-navigation and self-landing. Moreover, it has many advantages if combined with the frequency modulated continuous wave （FMCW） technology. A novel geometric configuration and an imaging algorithm for helicopter-borne FMCW-ROSAR are proposed. Firstly, by per- forming the equivalent phase center principle, the separated trans- mitting and receiving antenna system is equalized to the case of system configuration with antenna for both transmitting and receiving signals. Based on this, the accurate two-dimensional spectrum is obtained and the Doppler frequency shift effect in- duced by the continuous motion of the platform during the long pulse duration is compensated. Next, the impacts of the velocity approximation error on the imaging algorithm are analyzed in de- tail, and the system parameters selection and resolution analysis are presented. The well-focused SAR image is then obtained by using the improved Omega-K algorithm incorporating the accurate compensation method for the velocity approximation error. FJnally, correctness of the analysis and effectiveness of the proposed al- gorithm are demonstrated through simulation results.

Stochastic resonance in a single-mode laser driven by frequency modulated signal and coloured noises

By adding frequency modulated signals to the intensity equation of gain noise model of the single-mode laser driven by two coloured noises which are correlated, this paper uses the linear approximation method to calculate the power spectrum and signal-to-noise ratio （SNR） of the laser intensity. The results show that the SNR appears typical stochastic resonance with the variation of intensity of the pump noise and quantum noise. As the amplitude of a modulated signal has effects on the SNR, it shows suppression, monotone increasing, stochastic resonance, and multiple stochastic resonance with the variation of the frequency of a carrier signal and modulated signal.

Development of an injection-seeded single-frequency laser by using the phase modulated technique

An injection-seeded single-frequency Q-switched Nd：YAG laser is accomplished by using a phase modulated rampfire technique. A RbTiOPO4（RTP） electro-optic crystal is selected for effective optical path length modulation of the slave self-filtering unstable resonator. This single-frequency laser is capable of producing 50 m J pulse energy at 1 Hz repetition rate with a pulse width of 16 ns. The standard deviation of laser pulse intensity for consecutive 100 shots from the mean pulse intensity is less than 1.05%. A spectral linewidth of less than 0.5 pm with a frequency jitter of about 14 fm over30 min is obtained.

Frequency stabilization of a 399-nm laser by modulation transfer spectroscopy in an ytterbium hollow cathode lamp

The modulation transfer spectroscopy in an ytterbium hollow cathode lamp at 399 nm is measured. The error signal for frequency locking is optimized by measuring the dependences of its slope, linewidth and magnitude on various parameters. Under the optimum condition, the laser frequency at 399 nm can be stabilized. The long-term stability of laser frequency is measured by monitoring the fluorescence signal of the ytterbium atomic beam induced by the locked laser. The laser frequency is shown to be tightly locked, and the stabilized laser is successfully applied to the cooling of ytterbium atoms.

Flexible control of semiconductor laser with frequency tunable modulation transfer spectroscopy

We introduce a new method of simultaneously implementing frequency stabilization and frequency shift for semiconductor lasers. We name this method the frequency tunable modulation transfer spectroscopy （FTMTS）. To realize a stable output of 780 nm semiconductor laser, an FTMTS optical heterodyne frequency stabilization system is constructed. Before entering into the frequency stabilization system, the probe laser passes through an acousto-optical modulator （AOM） twice in advance to achieve tunable frequency while keeping the light path stable. According to the experimental results, the frequency changes from 120 MHz to 190 MHz after the double-pass AOM, and the intensity of laser entering into the system is greatly changed, but there is almost no change in the error signal of the FTMTS spectrum. Using this signal to lock the laser frequency, we can ensure that the frequency of the laser changes with the amount of AOM shift. Therefore, the magneto-optical trap （MOT）-molasses process can be implemented smoothly.

IMAGING ANALYSIS OF FREQUENCY MODULATION CONTINUOUS WAVE SYNTHETIC APERTURE RADAR IN NEAR RANGE MODE

Frequency-Modulation Continuous-Wave Synthetic Aperture Radar(FMCW SAR)has shown great potential in the applications of civil and military fields because of its easy deployment and low cost.However,most of these work and analysis are concentrated on airborne FMCW SAR,where the characteristics of the imaging geometry and signal are much similar to that of traditional pulsed-SAR.As a result,a series of test campaigns of automobile-based FMCW SAR were sponsored by Institute of Electronics,Chinese Academy of Sciences(IECAS)in the autumn of 2012.In this paper,we analyze the imaging issues of FMCW SAR in automobile mode(named as near range mode),where a vehicle is used as moving platform and a large looking angle is configured.The imaging geometry and signal properties are analyzed in detail.We emphasize the difference of the near range mode from the traditional airborne SAR mode.Based on the analysis,a focusing approach is proposed in the paper to handle the data focusing in the case.Simulation experiment and real data of automobile FMCW SAR are used to validate the analysis.

A 532 nm molecular iodine optical frequency standard based on modulation transfer spectroscopy

We report construction of an iodine-stabilized laser frequency standard at 532 nm based on modulation transfer spectroscopy(MTS)technology with good reproducibility.A frequency stability of 2.5×10^(-14)at 1 s averaging time is achieved,and the frequency reproducibility has a relative uncertainty of 3.5×10^(-13),demonstrating the great stability of our setup.The systematic uncertainty of the iodine-stabilized laser frequency standard is evaluated,especially the contribution of the residual amplitude modulation(RAM).The contribution of the RAM in MTS cannot be evaluated directly.To solve this problem,we theoretically deduce the MTS signal with RAM under large modulation depth,and prove that the non-symmetric shape of the MTS signal is directly related to the MTS effect.The non-symmetric shape factor can be calibrated with a frequency comb,and in real experiments,this value can be obtained by least-squares fitting of the MTS signal,from which we can infer the RAMinduced frequency shift.The full frequency uncertainty is evaluated to be 5.3 kHz(corresponding to a relative frequency uncertainty of 9.4×10^(-12)).The corrected transition frequency has a difference from the BIPM-recommended value of 2 kHz,which is within 1σ uncertainty,proving the validity of our evaluation.

Quasi-LFM radar waveform recognition based on fractional Fourier transform and time-frequency analysis

Recent advances in electronics have increased the complexity of radar signal modulation.The quasi-linear frequency modulation(quasi-LFM)radar waveforms(LFM,Frank code,P1−P4 code)have similar time-frequency distributions,and it is difficult to identify such signals using traditional time-frequency analysis methods.To solve this problem,this paper proposes an algorithm for automatic recognition of quasi-LFM radar waveforms based on fractional Fourier transform and time-frequency analysis.First of all,fractional Fourier transform and the Wigner-Ville distribution(WVD)are used to determine the number of main ridgelines and the tilt angle of the target component in WVD.Next,the standard deviation of the target component's width in the signal's WVD is calculated.Finally,an assembled classifier using neural network is built to recognize different waveforms by automatically combining the three features.Simulation results show that the overall recognition rate of the proposed algorithm reaches 94.17%under 0 dB.When the training data set and the test data set are mixed with noise,the recognition rate reaches 89.93%.The best recognition accuracy is achieved when the size of the training set is taken as 400.The algorithm complexity can meet the requirements of real-time recognition.

Strong optical feedback in birefringent dual frequency laser

Strong optical feedback in a birefringent dual frequency He-Ne laser with a high reflectivity feedback mirror has been investigated for the first time. The output characteristics of two orthogonally polarized modes are demonstrated in two different optical feedback cases： one is for both modes being fed back and the other is for only one of the modes being fed back. Strong mode competition can be observed between the two modes with strong optical feedback, And when one mode＇s intensity is near its maximum, the other mode is nearly extinguished. When both modes are fed back into the laser cavity, the mode competition is stronger than when only one mode is fed back, The difference in initial intensity between the two orthogonally polarized modes plays an important role in the mode competition, which has been experimentally and theoretically demonstrated.

A high frequency vibration compensation approach for ultrahigh resolution SAR imaging based on sinusoidal frequency modulation Fourier-Bessel transform

Ultrahigh resolution synthetic aperture radar(SAR)imaging for ship targets is significant in SAR imaging,but it suffers from high frequency vibration of the platform,which will induce defocus into SAR imaging results.In this paper,a novel compensation method based on the sinusoidal frequency modulation Fourier-Bessel transform(SFMFBT)is proposed,it can estimate the vibration errors,and the phase shift ambiguity can be avoided via extracting the time frequency ridge consequently.By constructing the corresponding compensation function and combined with the inverse SAR(ISAR)technique,well-focused imaging results can be obtained.The simulation imaging results of ship targets demonstrate the validity of the proposed approach.

Anti-interference method for HF radars by transmitting phase-modulated chirps

Radio frequency interference （RFI） is a major problem in high-frequency （HF） radars. Conventional filtering-involved RFI suppression methods may introduce distortions to the target signals of interest and often demand extra hardware costs. In this paper, a novel method for RFI suppression by using linearly or randomly phase-modulated （PM） chirps is proposed, which enables independent analyses of the target signal and the RFI. Furthermore, the directions of arrival （DOA） of the interference are used as constraints to ensure a better DOA estimation of the target. The effectiveness of the method is demonstrated by numerical simulation results. The method can greatly improve the anti-interference capabilities of HF radars and is extremely applicable in the portable and low-cost radar systems.

Strain measurement using frequency modulation fiber optic interferometer

The method for measuring the strain of an object using an optical fiber and a frequency modulation(FM) coupled cavity semiconductor laser is proposed.This method uses the coherent FM heterodyne principle of the Michelson interferometer and can avoid the π/2 nonreciprocal phase bias and phase shifting problem existing in general fiber optic interferential sensors, the maximum detection range is limited by the coherent length of the semiconductor laser and its relative factor.

Frequency Sweep Linearization for Semiconductor Laser Using a Feedback Loop Based on Amplitude-Frequency Response

A scheme of frequency sweep linearization of semiconductor lasers using a feed-back loop based on amplitude-frequency response is demonstrated in this paper. The beat frequency signal is obtained by self-heterodyne detection. The frequency changes are converted to the envelope of beat frequency signal after amplitude-frequency response. The active frequency sweep linearization is realized by feeding envelope deviations back to the drive currents of the lasers by a feedback loop. A simulation model is built to verify this scheme by Simulink. This scheme does not need high-performance, expensive lasers, complex linearization or tedious post-processing processes, which are of great significance for related applications.

DETECTION ON MICRO-DOPPLER EFFECT BASED ON LASER COHERENT RADAR

A laser coherent detection system of 1550 nm wavelength was presented, and experimen- tal research on detecting micro-Doppler effect in a dynamic target was developed. In the study, the return signal in the time domain is decomposed into a set of components in different wavelet scales by multi-resolution wavelet analysis, and the components are associated with the vibrational motions in a target. Then micro-Doppler signatures are extracted by applying the reconstruction. During the course of the final data processing frequency analysis and time-frequency analysis are applied to analyze the vibrationM signals and estimate the motion parameters successfully. The experimental results indicate that the system can effectively detect micro-Doppler information in a moving target, and the tiny vibrational signatures also can be acquired effectively by wavelet multi-resolution analy- sis and time-frequency analysis.

A 330-W single-frequency retrievable multi-tone monolithic fiber amplifier

A single-frequency retrievable phase modulated multi-tone fiber amplifier is presented in theory and demonstrated in experiment. A multi-tone seed laser generated by a sine wave phase modulated single-frequency laser is employed for stimulated Brillouin scattering suppression in an all-fiber amplifier. A demodulation signal which is π phase shifted with respect to the modulation signal is used to retrieve the single-frequency laser from the multi-tone laser. In experiment, we first optimize the all-fiber master-oscillator power-amplifier. With this amplifier, we demonstrate a single-frequency retrievable multi-tone laser with 330-W output when driven by the multi-tone seed, while the ultimate output power is only 130 W when driven by the single-frequency laser. Then, we carry out an experiment for retrieving the single-frequency laser from the amplified multi-tone laser. Results indicate that the single-frequency laser can be retrieved with a sideband suppression of more than 20 dB. Retrieving an even higher power single-frequency laser is possible if a high power demodulator is available.

Application Research on Space Laser Communication in Bistatic Radar System

There exist three synchronizing problems in the bistatic radar system that some signals of the radar receiver must be synchronized with those of the radar transmitter. Several methods realizing data transmission, which are used to complete the synchronization existing in the bistatic radar system, are described. Then a new idea is brought forward that employs space laser communication in the bistatic radar system to realize its data transmission. The theoretic analysis of the idea's usability and its merits are discussed in details. Finally the latest development of space laser communication is introduced, and the utility of the idea is pointed out further.

Two-frequency amplification in a semiconductor tapered amplifier for cold atom experiments

Simultaneous two-frequency amplification is highly desirable in cold atom experiments. The nonlinear response would appear in the two-frequency amplification with a semiconductor tapered amplifier（TA） and has a direct influence on the experimental result. We investigated in detail the effects of frequency difference, total power, and power ratio of two seeding lasers on the output components based on a simplified theoretical model. The simulation results showed that the multiple sideband generation in the amplifier due to self-phase and amplitude modulation could be suppressed and the TA tended to linearly amplify the power ratio between two-frequency components, when the two seeding lasers had a large frequency difference. This was verified experimentally in the output power ratio measurement via a calibrated Fabry-Perot interferometer method with a good linearity and an uncertainty of 1%. We also discussed the consequences of power ratio responses in the amplification in light of cold atom experiments, especially in the ac Stark shift related phase error of Raman-type atom interferometers（AIs）. It was shown that the fluctuation of intensity ratio of Raman beams may induce significant systematic errors for an AI gyroscope.

Theoretical analysis of frequency modulation-to-amplitude modulation on the final optics and target of the SG Ⅱ-Up laser facility

Frequency modulation(FM)-to-amplitude modulation(AM) conversion is an important factor that affects the time±power curve of inertial confinement fusion(ICF) high-power laser facilities. This conversion can impact uniform compression and increase the risk of damage to optics. However, the dispersive grating used in the smoothing by spectral dispersion technology will introduce a temporal delay and can spatially smooth the target. The combined effect of the dispersive grating and the focusing lens is equivalent to a Gaussian low-pass filter, which is equivalent to 8 GHz bandwidth and can reduce the intensity modulation on the target to below 5% with 0.3 nm @ 3 GHz + 20 GHz spectrum phase modulation. The results play an important role in the testing and evaluating of the FM-to-AM on the final optics and the target, which is beneficial for comprehensively evaluating the load capacity of the facility and isentropic compression experiment for ICF.

Dual-mode stabilization for laser to radio-frequency locking by using a single-sideband modulation and a Fabry-Pérot cavity

The dual-mode stabilization scheme has been demonstrated as an efficient way to stabilize laser frequency.In this study,we propose a novel dual-mode stabilization scheme that employs a sizable Fabry-Pérot cavity instead of the microcavity used in previous studies and has enabled higher bandwidth for locking.The results demonstrate a 30-fold reduction in laser frequency drift,with frequency instability below 169 kHz for integration time exceeding 1 h and a minimum value of 33.8 kHz at 54 min.Further improvement could be achieved by optimizing the phase locking.This scheme has potential for use in precision spectroscopic measurement.