The paper presents a method of calculating the full load engine characteristics based on the Leiderman–Khlystov relation. Because the values of the coefficients of the discussed function available in literature were ...The paper presents a method of calculating the full load engine characteristics based on the Leiderman–Khlystov relation. Because the values of the coefficients of the discussed function available in literature were determined for obsolete engine designs, an attempt was made to update them. To this end, a chassis dynamometer was used where a database of results had been built for a variety of vehicles. Following the data collection, the coefficients for variety of fueling system(six groups: fuel injected gasoline and turbocharged gasoline, spark ignition LPG Ⅰ–Ⅱ and Ⅳ generation, naturally aspirated diesel and turbocharged diesel) were determined. The identification of the coefficients was carried out in Matlab-Simulink indicating the applicability of the said function for most of the engines, yet the recent popularity of turbocharged gasoline engines requires an additional analysis of the possibility of use of a different functional description. The full load engine characteristics is a basis for the vehicle performance characteristics and, further, for modeling of traffic in a variety of aspects of the vehicle operation.展开更多
Loads on a gearbox casing of a certain type of tracked vehicle were calculated according to the engine＇s full load characteristic curve and the worst load condition where the gearbox operated while the tracked vehicl...Loads on a gearbox casing of a certain type of tracked vehicle were calculated according to the engine＇s full load characteristic curve and the worst load condition where the gearbox operated while the tracked vehicle was running, and then stiffness and strength of the casing were analyzed by means of Patran/Nastran software. After a- nalysis, it was found that the casing satisfied the Mises ＇ yield condition; however, the stress distribution was hetero- geneous, and stresses near the bearing saddle bores of the casing were higher while those in other regions were much less than the allowable stress. For this reason, thicknesses of the casing wall on bearing assembling holes needed in- creasing, while those in other places can decrease. After much structural improving and re-analysis, the optimal casing design was found, and its weight decreased by 5% ; the casing still satisfied the Mises yield criterion and the stress distribution was more homogeneous.展开更多
基金carried out within work no.S/WM/1/2018 realized at Bialystok University of Technologyfinanced from the funding allocated fo science by the Ministry of Science and Higher Education—Poland
文摘The paper presents a method of calculating the full load engine characteristics based on the Leiderman–Khlystov relation. Because the values of the coefficients of the discussed function available in literature were determined for obsolete engine designs, an attempt was made to update them. To this end, a chassis dynamometer was used where a database of results had been built for a variety of vehicles. Following the data collection, the coefficients for variety of fueling system(six groups: fuel injected gasoline and turbocharged gasoline, spark ignition LPG Ⅰ–Ⅱ and Ⅳ generation, naturally aspirated diesel and turbocharged diesel) were determined. The identification of the coefficients was carried out in Matlab-Simulink indicating the applicability of the said function for most of the engines, yet the recent popularity of turbocharged gasoline engines requires an additional analysis of the possibility of use of a different functional description. The full load engine characteristics is a basis for the vehicle performance characteristics and, further, for modeling of traffic in a variety of aspects of the vehicle operation.
文摘Loads on a gearbox casing of a certain type of tracked vehicle were calculated according to the engine＇s full load characteristic curve and the worst load condition where the gearbox operated while the tracked vehicle was running, and then stiffness and strength of the casing were analyzed by means of Patran/Nastran software. After a- nalysis, it was found that the casing satisfied the Mises ＇ yield condition; however, the stress distribution was hetero- geneous, and stresses near the bearing saddle bores of the casing were higher while those in other regions were much less than the allowable stress. For this reason, thicknesses of the casing wall on bearing assembling holes needed in- creasing, while those in other places can decrease. After much structural improving and re-analysis, the optimal casing design was found, and its weight decreased by 5% ; the casing still satisfied the Mises yield criterion and the stress distribution was more homogeneous.
