In this work, we have modeled and simulated the electrical performance of CIGS thin-film solar cell using one-dimensional simulation software (SCAPS-1D). Starting from a baseline model that reproduced the experimental...In this work, we have modeled and simulated the electrical performance of CIGS thin-film solar cell using one-dimensional simulation software (SCAPS-1D). Starting from a baseline model that reproduced the experimental results, the properties of the absorber layer and the CIGS/Mo interface have been explored, and the requirements for high-efficiency CIGS solar cell were proposed. Simulation results show that the band-gap, acceptor density, defect density are crucial parameters that affect the performance of the solar cell. The best conversion efficiency is obtained when the absorber band-gap is around 1.2 eV, the acceptor density at 10<sup>16</sup> cm<sup><span style="white-space:nowrap;">−</span>3</sup> and the defect density less than 10<sup>14</sup> cm<sup><span style="white-space:nowrap;">−</span>3</sup>. In addition, CIGS/Mo interface has been investigated. It appears that a thin MoSe<sub>2</sub> layer reduces recombination at this interface. An improvement of 1.5 to 2.5 mA/cm<sup>2</sup> in the current density (<em>J<sub>sc</sub></em>) depending on the absorber thickness is obtained.展开更多
In order to achieve low cost high efficiency thin film solar cells,a novel Semiconductor Photovoltaic (PV) active material CuIn 1-x Ga x Se 2 (CIGS) and thin film Electro Deposition (ED) technology is explored.Firstly...In order to achieve low cost high efficiency thin film solar cells,a novel Semiconductor Photovoltaic (PV) active material CuIn 1-x Ga x Se 2 (CIGS) and thin film Electro Deposition (ED) technology is explored.Firstly,the PV materials and technologies is investigated,then the detailed experimental processes of CIGS/Mo/glass structure by using the novel ED technology and the results are reported.These results shows that high quality CIGS polycrystalline thin films can be obtained by the ED method,in which the polycrystalline CIGS is definitely identified by the (112),(204,220) characteristic peaks of the tetragonal structure,the continuous CIGS thin film layers with particle average size of about 2μm of length and around 1 6μm of thickness.The thickness and solar grade quality of CIGS thin films can be produced with good repeatability.Discussion and analysis on the ED technique,CIGS energy band and sodium (Na) impurity properties,were also performed.The alloy CIGS exhibits not only increasing band gap with increasing x ,but also a change in material properties that is relevant to the device operation.The beneficial impurity Na originating from the low cost soda lime glass substrate becomes one prerequisite for high quality CIGS films.These novel material and technology are very useful for low cost high efficiency thin film solar cells and other devices.展开更多
Thin films of copper indium gallium selenide Cu（In,Ga）Se2 （CIGS） were prepared by sequential elemental layer deposition in vacuum at room temperature. The as-deposited films were heated in vacuum for compound form...Thin films of copper indium gallium selenide Cu（In,Ga）Se2 （CIGS） were prepared by sequential elemental layer deposition in vacuum at room temperature. The as-deposited films were heated in vacuum for compound formation, and were studied at temperature as high as 1250℃ for the first time. These films were concurrently studied for their structural properties by X-ray diffraction （XRD） technique. The XRD analyses include phase transition studies, grain size variation and microstrain measurements with the reaction temperature and time.It has been observed that there are three distinct regions of variation in all these parameters. These regions belong to three temperature regimes： 〈450℃, 450-950℃, and 〉950℃. It is also seen that the compound formation starts at 250℃, with ternary phases appearing at 350℃ or above. Whereas, there is another phase shift at 950℃ without any preference to the quaternary compound.展开更多
温度特性是太阳电池的一个重要特征,本文研究了Cu(In,Ga)Se_2(CIGS)薄膜太阳电池的输出特性随温度变化(120~260 K))的规律。发现,随着温度升高,开路电压Voc明显降低,温度系数为-1.08m V/K,短路电流Isc小幅升高,温度系数为0.01401 m A/K...温度特性是太阳电池的一个重要特征,本文研究了Cu(In,Ga)Se_2(CIGS)薄膜太阳电池的输出特性随温度变化(120~260 K))的规律。发现,随着温度升高,开路电压Voc明显降低,温度系数为-1.08m V/K,短路电流Isc小幅升高,温度系数为0.01401 m A/K。这是因为:随着温度上升,禁带宽度下降,暗电流增加,造成开路电压的降低;更多的光生载流子被激发,串联电阻有所下降,使得短路电流增加。两者共同作用,电池效率有所下降。展开更多
文摘In this work, we have modeled and simulated the electrical performance of CIGS thin-film solar cell using one-dimensional simulation software (SCAPS-1D). Starting from a baseline model that reproduced the experimental results, the properties of the absorber layer and the CIGS/Mo interface have been explored, and the requirements for high-efficiency CIGS solar cell were proposed. Simulation results show that the band-gap, acceptor density, defect density are crucial parameters that affect the performance of the solar cell. The best conversion efficiency is obtained when the absorber band-gap is around 1.2 eV, the acceptor density at 10<sup>16</sup> cm<sup><span style="white-space:nowrap;">−</span>3</sup> and the defect density less than 10<sup>14</sup> cm<sup><span style="white-space:nowrap;">−</span>3</sup>. In addition, CIGS/Mo interface has been investigated. It appears that a thin MoSe<sub>2</sub> layer reduces recombination at this interface. An improvement of 1.5 to 2.5 mA/cm<sup>2</sup> in the current density (<em>J<sub>sc</sub></em>) depending on the absorber thickness is obtained.
基金Project Supported by the Innovation and Technology Fund ( ITF ) of The Government of The Hong Kong Special Administrative Region ( HK-SAR)China( Fund Grant Num ber:S/ P0 0 5 / 99)
文摘In order to achieve low cost high efficiency thin film solar cells,a novel Semiconductor Photovoltaic (PV) active material CuIn 1-x Ga x Se 2 (CIGS) and thin film Electro Deposition (ED) technology is explored.Firstly,the PV materials and technologies is investigated,then the detailed experimental processes of CIGS/Mo/glass structure by using the novel ED technology and the results are reported.These results shows that high quality CIGS polycrystalline thin films can be obtained by the ED method,in which the polycrystalline CIGS is definitely identified by the (112),(204,220) characteristic peaks of the tetragonal structure,the continuous CIGS thin film layers with particle average size of about 2μm of length and around 1 6μm of thickness.The thickness and solar grade quality of CIGS thin films can be produced with good repeatability.Discussion and analysis on the ED technique,CIGS energy band and sodium (Na) impurity properties,were also performed.The alloy CIGS exhibits not only increasing band gap with increasing x ,but also a change in material properties that is relevant to the device operation.The beneficial impurity Na originating from the low cost soda lime glass substrate becomes one prerequisite for high quality CIGS films.These novel material and technology are very useful for low cost high efficiency thin film solar cells and other devices.
文摘Thin films of copper indium gallium selenide Cu（In,Ga）Se2 （CIGS） were prepared by sequential elemental layer deposition in vacuum at room temperature. The as-deposited films were heated in vacuum for compound formation, and were studied at temperature as high as 1250℃ for the first time. These films were concurrently studied for their structural properties by X-ray diffraction （XRD） technique. The XRD analyses include phase transition studies, grain size variation and microstrain measurements with the reaction temperature and time.It has been observed that there are three distinct regions of variation in all these parameters. These regions belong to three temperature regimes： 〈450℃, 450-950℃, and 〉950℃. It is also seen that the compound formation starts at 250℃, with ternary phases appearing at 350℃ or above. Whereas, there is another phase shift at 950℃ without any preference to the quaternary compound.
文摘温度特性是太阳电池的一个重要特征,本文研究了Cu(In,Ga)Se_2(CIGS)薄膜太阳电池的输出特性随温度变化(120~260 K))的规律。发现,随着温度升高,开路电压Voc明显降低,温度系数为-1.08m V/K,短路电流Isc小幅升高,温度系数为0.01401 m A/K。这是因为:随着温度上升,禁带宽度下降,暗电流增加,造成开路电压的降低;更多的光生载流子被激发,串联电阻有所下降,使得短路电流增加。两者共同作用,电池效率有所下降。
