A transient production prediction method for tight condensate gas wells with multiphase flow

Considering the phase behaviors in condensate gas reservoirs and the oil-gas two-phase linear flow and boundary-dominated flow in the reservoir,a method for predicting the relationship between oil saturation and pressure in the full-path of tight condensate gas well is proposed,and a model for predicting the transient production from tight condensate gas wells with multiphase flow is established.The research indicates that the relationship curve between condensate oil saturation and pressure is crucial for calculating the pseudo-pressure.In the early stage of production or in areas far from the wellbore with high reservoir pressure,the condensate oil saturation can be calculated using early-stage production dynamic data through material balance models.In the late stage of production or in areas close to the wellbore with low reservoir pressure,the condensate oil saturation can be calculated using the data of constant composition expansion test.In the middle stages of production or when reservoir pressure is at an intermediate level,the data obtained from the previous two stages can be interpolated to form a complete full-path relationship curve between oil saturation and pressure.Through simulation and field application,the new method is verified to be reliable and practical.It can be applied for prediction of middle-stage and late-stage production of tight condensate gas wells and assessment of single-well recoverable reserves.

Flux vector splitting solutions for coupling hydraulic transient of gas-liquid-solid three-phase flow in pipelines

The gas-liquid-solid three-phase mixed flow is the most general in multiphase mixed transportation. It is significant to exactly solve the coupling hydraulic transient problems of this type of multiphase mixed flow in pipelines. Presently, the method of characteristics is widely used to solve classical hydraulic transient problems. However, when it is used to solve coupling hydraulic transient problems, excessive interpolation errors may be introduced into the results due to unavoidable multiwave interpolated calculations. To deal with the problem, a finite difference scheme based on the Steger- Warming flux vector splitting is proposed. A flux vector splitting scheme is established for the coupling hydraulic transient model of gas-liquid-solid three-phase mixed flow in the pipelines. The flux subvectors are then discretized by the Lax-Wendroff central difference scheme and the Warming-Beam upwind difference scheme with second-order precision in both time and space. Under the Rankine-Hugoniot conditions and the corresponding boundary conditions, an effective solution to those points located at the boundaries is developed, which can avoid the problem beyond the calculation region directly induced by the second-order discrete technique. Numerical and experimental verifications indicate that the proposed scheme has several desirable advantages including high calculation precision, excellent shock wave capture capability without false numerical oscillation, low sensitivity to the Courant number, and good stability.

Heat Transfer Method for Solid Flow Rate Measurement in Gas-Solid Two Phase Flow

ＨｅａｔＴｒａｎｓｆｅｒＭｅｔｈｏｄｆｏｒＳｏｌｉｄＦｌｏｗＲａｔｅＭｅａｓｕｒｅｍｅｎｔｉｎＧａｓＳｏｌｉｄＴｗｏＰｈａｓｅＦｌｏｗＹｕａｎＺｈｕｌｉｎ（袁竹林）ＬｕＺｕｏｊｉ（卢作基）（ＴｈｅｒｍｏｅｎｅｒｇｙＥｎｇｉｎｅｅｒｉｎｇＲｅｓｅａｒ...

Numerical simulation of the gas-solid two-phase flow inside the multi-channel nozzle for the surface nanocrystallization induced by the ultrasonic particulate peening

Using a gas-solid two-phase model(a discrete phase model),the authors investigated the flow field inside the multi-channel nozzle for surface nanocrystallization(SNC)induced by the ultrasonic particulate peening(USPP).By computation,the velocity fields of both the gas and the solid phases were simulated and the track of the solid phase was analyzed in detail.It can be found that the velocities of the two phases are able to reach an ultrasonic level;meanwhile,the dispersion width of the solid phase at the nozzle exit is less than that of the gas phase.When particle diameters are less than 5 μm,there is a decreasing trend in the dispersion width of the solid phase with an increase in particle diameters.The trend becomes stable as the particle diameters are greater than 5 μm;in the meantime,the distribution of solid particles is near the axis of the jet flow.The optimal standoff distance between the nozzle and the substrate in the process of USPP is about 120 mm.Simulation results can help improve the design of mass-production-oriented multi-channel nozzles for SNC induced by USPP.

Numerical Simulation of the Gas-solid Two-phase Flows in a Precalciner

The gas-solid two-phase flous of the precalciner were simulated by different multiphase models,such as mixture model,the Enderium model,including mixture and dispersed,and discrete phase model（DPM）,The results of the different multiphase models were analyzed and compared.showing the rationality of the diffusion and mixture of the cenment raic meals and coal poroder some extent Moreover,the results also shose the rationality of the given inlets parameters of actual process of the precalciner.

RESEARCH ON METHOD TO CALCULATE VELOCITIES OF SOLID PHASE AND LIQUID PHASE IN DEBRIS FLOW

Velocities of solid phase and liquid phase in debris flow are one key problem to research on impact and abrasion mechanism of banks and control structures under action of debris flow. Debris flow was simplified as two-phase liquid composed of solid phase with the same diameter particles and liquid phase with the same mechanical features. Assume debris flow was one-dimension two-phase liquid moving to one direction, then general equations of velocities of solid phase and liquid phase were founded in two-phase theory. Methods to calculate average pressures, volume forces and surface forces of debris flow control volume were established. Specially, surface forces were ascertained using Bingham＇s rheology equation of liquid phase and Bagnold＇s testing results about interaction between particles of solid phase. Proportional coefficient of velocities between liquid phase and solid phase was put forward, meanwhile, divergent coefficient between theoretical velocity and real velocity of solid phase was provided too. To state succinctly before, method to calculate velocities of solid phase and liquid phase was obtained through solution to general equations. The method is suitable for both viscous debris flow and thin debris flow. Additionally, velocities every phase can be identified through analyzing deposits in-situ after occurring of debris flow. It is obvious from engineering case the result in the method is consistent to that in real-time field observation.

Gas‐phase fluorination of conjugated microporous polymer microspheres for effective interfacial stabilization in lithium metal anodes

Lithium(Li)metal anodes have attracted extensive attention due to their ultrahigh theoretical capacity and low potential.However,the uneven deposition of Li near the unstable electrode/electrolyte interfaces leads to the growth of Li dendrites and the degradation of active electrodes.Herein,we directly fluorinate alkyne-containing conjugated microporous polymers(ACMPs)microspheres with fluorine gas(F_(2))to introduce a novel fluorinated interlayer as an interfacial stabilizer in lithium metal batteries.Using density functional theory methods,it is found that as-prepared fluorinated ACMP(FACMP)has abundant partially ionic C–F bonds.The C–F bonds with electrochemical lability yield remarkable lithiophilicity during cycling.The in situ reactions between the active C–F bonds and Li ions enable transfer of lithium fluoride microcrystals to the solid electrolyte interphase(SEI)layers,guaranteeing effective ionic distribution and smooth Li deposition.Consequently,Li metal electrodes with the fluorinated interlayers demonstrate excellent cycling performances in both half-batteries and full cells with a lithium bis(trifluoromethanesulfonyl)imide electrolyte as well as a nonfluorinated lithium bis(oxalate)borate electrolyte system.This strategy is highly significant in customizable SEI layers to stabilize electrode interfaces and ensure high utilization of Li metal anodes,especially in a nonfluorinated electrolyte.

Numerical simulation and analysis of solid-liquid two-phase threedimensional unsteady flow in centrifugal slurry pump

Based on RNG k-ε turbulence model and sliding grid technique, solid-liquid two-phase three-dimensional(3-D) unsteady turbulence of full passage in slurry pump was simulated by means of Fluent software. The effects of unsteady flow characteristics on solid-liquid two-phase flow and pump performance were researched under design condition. The results show that clocking effect has a significant influence on the flow in pump, and the fluctuation of flow velocity and pressure is obvious, particularly near the volute tongue, at the position of small sections of volute and within diffuser. Clocking effect has a more influence on liquid-phase than on solid-phase, and the wake-jet structure of relative velocity of solid-phase is less obvious than liquid-phase near the volute tongue and the impeller passage outlet. The fluctuation of relative velocity of solid-phase flow is 7.6% smaller than liquid-phase flow at the impeller outlet on circular path. Head and radial forces of the impeller are 8.1% and 85.7% of fluctuation, respectively. The results provide a theoretical basis for further research for turbulence, improving efficient, reducing the hydraulic losses and wear. Finally, field tests were carried out to verify the operation and wear of slurry pump.

Computational Analysis of Centrifugal Pump Delivering Solid-liquid Two-phase Flow during Startup Period

The transient behavior of centrifugal pumps during transient operating periods, such as startup and stopping, has drawn more and more attention recently because of urgent needs in engineering. Up to now, almost all the existing studies on this behavior are limited to using water as working fluid. The study on the transient behavior related to solid-liquid two-phase flow has not been seen yet. In order to explore the transient characteristics of a high specific-speed centrifugal pump during startup period delivering the pure water and solid-liquid two-phase flow, the transient flows inside the pump are numerically simulated using the dynamic mesh method. The variable rotational speed and flow rate with time obtained from experiment are best fitted as the function of time, and are written into computational fluid dynamics （CFD） code-FLUENT by using a user defined function. The predicted heads are compared with experimental results when pumping pure water. The results show that the difference in the transient performance during startup period is very obvious between water and solid-liquid two-phase flow during the later stage of startup process. Moreover, the time for the solid-liquid two-phase flow to achieve a stable condition is longer than that for water. The solid-liquid two-phase flow results in a higher impeller shaft power, a larger dynamic reaction force, a more violent fluctuation in pressure and a reduced stable pressure rise comparing with water. The research may be useful to tmderstanding on the transient behavior of a centrifugal pump under a solid-liquid two-phase flow during startup period.

A Multiphase Wellbore Flow Model for Sour Gas “Kicks”

This study presents a new multiphase flow model with transient heat transfer and pressure coupling to simulate HTHP(high temperature and high pressure)sour gas“kicks”phenomena.The model is intended to support the estimation of wellbore temperature and pressure when sour gas kicks occur during drilling operation.The model considers sour gas solubility,phase transition and effects of temperature and pressure on the physical parameters of drilling fluid.Experimental data for a large-diameter pipe flow are used to validate the model.The results indicate that with fluid circulation,the annulus temperature with H2S kicks is the highest,followed by CO_(2),and CH_(4) is the lowest.The phase transition point of H2S is closer to wellhead compared with CO_(2),resulting in a faster expansion rate,which is more imperceptible and dangerous.With fluid circulation,the drilling fluid density and plastic viscosity both first decrease and then increase with the increase in the well depth.The bottom hole pressure when H2S kicks is greater than that for CO_(2) with the same amount of sour gas,and the pressure difference gradually increases with the increase of H2S/CO_(2) content.In addition,a parametric sensitivity analysis has been conducted to evaluate qualitatively and rank the influential factors affecting the bottom hole temperature and pressure.

Numerical Simulation of Erosion-Corrosion in the Liquid-Solid Two-Phase Flow

Erosion-corrosion of liquid-solid two-phase flow occurring in a pipe with sudden expansion in cross-section is numerically simulated in this paper. The global model for erosion-corrosion process includes three main components: the liquid-solid two-phase flow model, erosion model and corrosion model. The Eulerian-Lagrangian approach is used to simulate liquid-solid two-phase flow, while the stochastic trajectory model was adopted to obtain properties of particle phase. Two-way coupling effect between the fluid and the particle phase is considered in the model. The accuracy of the models is tested by the data in the reference. The comparison shows that the model is basically correct and feasible.

Numerical Simulation of Gas-Solid Flow in Square Cyclone Separators with Downward Exit

Cyclone separators are widely used in industrial applications. The separation efficiency and pressure drop are the most important parameters to evaluate the performance of processing system. In the simulations,the flow behavior of gas and particles within a square cyclone separator is simulated by means of computational fluid dynamics. The RNG k- ε model and the Reynolds stress model( RSM) are used to model gas turbulence. The flow behavior is examined in the term of tangential velocity components,static pressure and pressure drop contour plots for flow field and solid volume fraction. The effects of the turbulence model and solid volume fraction on the square cyclone are discussed. The results indicate that the pressure drop increases with the increase of solid volume fraction,and increase with the increase of inlet velocities for two turbulence models, moreover,the simulations results are compared with pressure field. For all runs,the RSM model gives a higher pressure drop compared to the RNG k- ε model. The RSM model provides well the forced vortex and free vortex,and captures better the phenomena occurring during intense vortex flow in the presence of walls within cyclone separators.

A Numerical Sirnulation of Gas-Particle Two-Phase Flow in a Suspension Bed Using DifFusion Flux Model

A mathematical model of two-dimensional turbulent gas-particle two-phase flow based on the modified diffusion flux model (DFM) and a numerical simulation method to analyze the gas-particle flow structures are developed. The modified diffusion flux model, in which the acceleration due to various forces is taken into account for the calculation of the diffusion velocity of particles, is applicable to the analysis of multi-dimensional gas-particle two-phase turbulent flow. In order to verify its accuracy and efficiency, the numerical simulation by DFM is compared with experimental studies and the prediction by κ-ε-κp two-fluid model, which shows a reasonable agreement. It is confirmed that the modified diffusion flux model is suitable for simulating the multi-dimensional gas-particle two-phase flow.

Numerical simulation of predicting and reducing solid particle erosion of solid-liquid two-phase flow in a choke

Chokes are one of the most important components of downhole flow-control equipment. The particle erosion mathematical model, which considers particle-particle interaction, was established and used to simulate solid particle movement as well as particle erosion characteristics of the solid-liquid two-phase flow in a choke. The corresponding erosion reduction approach by setting ribs on the inner wall of the choke was advanced. This mathematical model includes three parts： the flow field simulation of the continuous carrier fluid by an Eulerian approach, the particle interaction simulation using the discrete particle hard sphere model by a Lagrangian approach and calculation of erosion rate using semiempirical correlations. The results show that particles accumulated in a narrow region from inlet to outlet of the choke and the dominating factor affecting particle motion is the fluid drag force. As a result, the optimization of rib geometrical parameters indicates that good anti-erosion performance can be achieved by four ribs, each of them with a height （H） of 3 mm and a width （B） of 5 mm equaling the interval between ribs （L）.

Critical Stokes Number for Gas-Solid Flow Erosion of Wind Turbine Airfoil

Wind turbine blades are inevitable to be eroded in wind-sand environment,so it is crucial to identify the flow conditions under which the erosion happens.Here,the effect of the sand diameter on wind turbine airfoil is first investigated.When the sand diameter is less than 3μm,the sands will bypass the airfoil and no erosion occurs.When the sand diameter is larger than 4μm,the sand grains collide with the airfoil and the erosion happens.Thus,there must be a critical sand diameter between 3μm and 4μm,at which the erosion is initiated on the airfoil surface.To find out this critical value,aparticle Stokes number is introduced here.According to the range of the critical sand diameter mentioned above,the critical value of particle Stokes number is reasonably assumed to be between 0.007 8and 0.014.The assumption is subsequently validated by other four factors influecing the erosion,i.e.,the angle of attack,relative thickness of the airfoil,different series airfoil,and inflow velocity.Therefore,the critical range of Stokes number has been confirmed.

Rate transient analysis methods for water-producing gas wells in tight reservoirs with mobile water

Tight gas reservoirs with mobile water exhibit multi-phase flow and high stress sensitivity.Accurately analyzing the reservoir and well parameters using conventional single-phase rate transient analysis methods proves challenging.This study introduces novel rate transient analysis methods incorporating evaluation processes based on the conventional flowing material balance method and the Blasingame type-curve method to examine fractured gas wells producing water.By positing a gas-water two-phase equivalent homogenous phase that considers characteristics of mobile water,gas,and high stress sensitivity,the conventional single-phase rate transient analysis methods can be applied by integrating the phase's characteristics and defining the phase's normalized parameters and material balance pseudotime.The rate transient analysis methods based on the equivalent homogenous phase can be used to quantitatively assess the parameters of wells and gas reservoirs,such as original gas-in-place,fracture half-length,reservoir permeability,and well drainage radius.This facilitates the analysis of production dynamics of fractured wells and well-controlled areas,subsequently aiding in locating residual gas and guiding the configuration of well patterns.The specific evaluation processes are detailed.Additionally,a numerical simulation mechanism model was constructed to verify the reliability of the developed methods.The methods introduced have been successfully implemented in field water-producing gas wells within tight gas reservoirs containing mobile water.

Pressure Drop of Liquid–Solid Two-Phase Flow in the Vertical Tube Bundle of a Cold-Model Circulating Fluidized Bed Evaporator

A cold-model vertical multi-tube circulating fluidized bed evaporator was designed and built to conduct a visualization study on the pressure drop of a liquid–solid two-phase flow and the corresponding particle distribution.Water and polyformaldehyde particle(POM)were used as the liquid and solid phases,respectively.The effects of operating parameters such as the amount of added particles,circulating flow rate,and particle size were systematically investigated.The results showed that the addition of the particles increased the pressure drop in the vertical tube bundle.The maximum pressure drop ratios were 18.65%,21.15%,18.00%,and 21.15%within the experimental range of the amount of added particles for POM1,POM2,POM3,and POM4,respectively.The pressure drop ratio basically decreased with the increase in the circulating flow rate but fluctuated with the increase in the amount of added particles and particle size.The difference in pressure drop ratio decreased with the increase in the circulating flow rate.As the amount of added particles increased,the difference in pressure drop ratio fluctuated at low circulating flow rate but basically decreased at high circulating flow rate.The pressure drop in the vertical tube bundle accounted for about 70%of the overall pressure drop in the up-flow heating chamber and was the main component of the overall pressure within the experimental range.Three-dimensional phase diagrams were established to display the variation ranges of the pressure drop and pressure drop ratio in the vertical tube bundle corresponding to the operating parameters.The research results can provide some reference for the application of the fluidized bed heat transfer technology in the industry.

A study on periodic boundary condition in direct numerical simulation for gas–solid flow

Direct numerical simulation(DNS) of gas–solid flow at high resolution has been carried out by coupling the lattice Boltzmann method(LBM) for gas flow and the discrete element method(DEM) for solid particles. However,the body force periodic boundary condition(FPBC) commonly used to cut down the huge computational cost of such simulation has faced accuracy concerns. In this study, a novel two-region periodic boundary condition(TPBC) is presented to remedy this problem, with the flow driven in the region with body force and freely evolving in the other region. With simulation cases for simple circulating fluidized bed risers, the validity and advantages of TPBC are demonstrated with more reasonable heterogeneity of the particle distribution as compared to the corresponding case with FPBC.

Determination of an Organophosphorus Pesticide Chlorpyrifos in Seawater by Solid Phase Extraction-Gas Chromatography

Solid phase extraction(SPE) and gas chromatography(GC) were combined to establish a method for detecting traces of chlorpyrifos in seawater,and the effects of extraction column type,water sample pH and salinity,and eluant type on the recovery rate of chlorpyrifos were analyzed. The results show that the linear range of the method was 0.02-2.0 μg/ml,and the correlation coefficient was 0.9993; the recovery rate of chlorpyrifos in the seawater samples to which the standard sample of chlorpyrifos averaged 101%-114%; MDL was 0.00851μg/L,and the lower limit of determination for chlorpyrifos was 0.034μg/L; the relative standard deviation ranged from 1.52% to 6.21%(n = 6). The method is simple,sensitive and accurate and has good repeatability. It is suitable for the determination of traces of chlorpyrifos in seawater.

Determination of Tebuconazole Residue in Apples and Vegetables by Matrix Solid Phase Dispersion-Gas Chromatography

[ Objective] The study aimed to determine tebuconazole residue in apples and vegetables using matrix solid phase dispersion-gas chro- matography （MSPD-GC）. [ Method] The effects of extraction and determination conditions on the detection of tebuconazole left in apples and veg- etables were analyzed, and the optimum extraction conditions were determined. [ Result] The recovery rate of tebucenazole was the highest when the ratio of a sample to florisil dispersant was 1 ： 4, and the mixture of hexane and acetone （ 1 ： 1 ） with total volume of 8 ml was as the eluant. Under the optimum conditions, the relative standard deviation （RSD） of the method was 4.9% -7.6%, and the detection limit was 0.1 tJg/g, while the re- covery rate of tebuconazole changed from 86.7% to 95. 2% . [ Conclusion] The method was simple, accurate, sensitive and applicable to the de- termination of tebuconazole in aaricultural Droducts.