Tuning energy output of PTFE/Al composite materials through gradient structure

As a typical energetic composite,polytetrafluoroethylene(PTFE)/aluminum(Al)has been widely applied in explosives,pyrotechnics,and propellants due to its ultra-high energy density and intense exothermic reaction.In this work,the radial gradient(RG)structure of PTFE/Al cylinders with three different PTFE morphologies(200 nm and 5μm particles and 5μm fiber)and content changes are prepared by 3D printing technology.The effect of radial gradient structure on the pressure output of PTFE/Al has been studied.Compared with the morphology change of PTFE,the change of component content in the gradient structure has an obvious effect on the pressure output of the PTFE/Al cylinder.Furthermore,the relationships of the morphology,content of PTFE and the combustion reaction of the PTFE/Al cylinder reveal that the cylinder shows a more complex flame propagation process than others.These results could provide a strategy to improve the combustion and pressure output of PTFE/Al.

Study of the axial density/impedance gradient composite long rod hypervelocity penetration into a four-layer Q345 target

Based on the dynamic shock response of the material and structure,the hypervelocity impact processes and mechanisms of long composite rods with axial density/impedance gradients penetration into fourlayer targets were studied through experiments and numerical simulation methods.The propagation law of the shock waves,together with the structural responses of the projectiles and targets,the formation and evolution of the fragment groups formed during the processes and their distributions were described.The damage of each target plate was quantitatively analysed by comparing the results of the experiment and numerical simulation.The results showed that the axial density/impedance gradient projectiles could decrease the impact pressure to a certain extent,and the degree of damage to the target plate decreased layer by layer when the head density/impedance of the projectile was high.When the head density/impedance of the projectile was low,the degree of target damage first increased layer by layer until the projectile was completely eroded and then it decreased.The results can provide a reference for the design and application of long rods with axial composite structure for velocities ranging from 6 to 10 Ma or greater.

Functionally graded structure of a nitride-strengthened Mg_(2)Si-based hybrid composite

The ex-situ incorporation of the secondary SiC reinforcement,along with the in-situ incorporation of the tertiary and quaternary Mg_(3)N_(2) and Si_(3)N_(4) phases,in the primary matrix of Mg_(2)Si is employed in order to provide ultimate wear resistance based on the laser-irradiation-induced inclusion of N_(2) gas during laser powder bed fusion.This is substantialized based on both the thermal diffusion-and chemical reactionbased metallurgy of the Mg_(2)Si–SiC/nitride hybrid composite.This study also proposes a functional platform for systematically modulating a functionally graded structure and modeling build-direction-dependent architectonics during additive manufacturing.This strategy enables the development of a compositional gradient from the center to the edge of each melt pool of the Mg_(2)Si–SiC/nitride hybrid composite.Consequently,the coefficient of friction of the hybrid composite exhibits a 309.3%decrease to–1.67 compared to–0.54 for the conventional nonreinforced Mg_(2)Si structure,while the tensile strength exhibits a 171.3%increase to 831.5 MPa compared to 485.3 MPa for the conventional structure.This outstanding mechanical behavior is due to the(1)the complementary and synergistic reinforcement effects of the SiC and nitride compounds,each of which possesses an intrinsically high hardness,and(2)the strong adhesion of these compounds to the Mg_(2)Si matrix despite their small sizes and low concentrations.

Almost Sure Convergence of Proximal Stochastic Accelerated Gradient Methods

Proximal gradient descent and its accelerated version are resultful methods for solving the sum of smooth and non-smooth problems. When the smooth function can be represented as a sum of multiple functions, the stochastic proximal gradient method performs well. However, research on its accelerated version remains unclear. This paper proposes a proximal stochastic accelerated gradient (PSAG) method to address problems involving a combination of smooth and non-smooth components, where the smooth part corresponds to the average of multiple block sums. Simultaneously, most of convergence analyses hold in expectation. To this end, under some mind conditions, we present an almost sure convergence of unbiased gradient estimation in the non-smooth setting. Moreover, we establish that the minimum of the squared gradient mapping norm arbitrarily converges to zero with probability one.

Centrifugal casting processes of manufacturing in situ functionally gradient composite materials of Al-19Si-5Mg alloy

Cylindrical components of in situ functionally gradient composite materials of Al-19Si-5Mg alloy were manufactured by centrifugal casting. Microstructure characteristics of the manufactured components were observed and the effects of the used process factors on these characteristics were analyzed. The results of observations shows that, in thickness, the components possess microstructures accumulating lots of Mg2Si particles and a portion of primary silicon particles in the inner layer, a little MgzSi and primary silicon particles in the outer layer, and without any Mg2Si and primary silicon particle in the middle layer. The results of the analysis indicate that the rotation rate of centrifugal casting, mould temperature, and melt pouring temperature have evidently affected the accumulation of the second phase particles. Also, the higher the centrifugal rotation rate, mould temperature, and melt pouring temperature are, the more evident in the inner layer the degree of accumulation of Mg2Si and primary silicon particles is.

Anti-penetration performance of high entropy alloy–ceramic gradient composites

A high-entropy alloy–ceramic gradient composite of TiC–TiB_2/75vol% Al_(0.3) CoCrFe Ni was successfully prepared by combustion synthesis under an ultra-high gravity field, which is a low-cost method with high efficiency. The ceramic particles were gradient distributed in the Al_(0.3) CoCrFe Ni matrix, and the hardness of the composite material gradually decreased along the thickness direction. The anti-penetration performance of the gradient composites was simulated using the ANSYS/LS-DYNA explicit simulation program. The results demonstrate that the distribution of the ceramic particles strongly affected the mechanical properties and the anti-penetration performance of the composites. With the same total ceramic volume fraction, the gradient composites exhibit better anti-penetration performance than the corresponding ceramic–metal interlayer composites. The more uneven the ceramic distribution, the greater the elastic modulus and yield stress of the surface layer and, thus, the better the anti-penetration performance.

Structure and Mechanical Properties of Al-based Gradient Composites Reinforced with Primary Si and Mg_2Si Particles through Centrifugal Casting

The structure and mechanical properties of a new type of Al-based discontinuous gradient composites prepared by using the ternary AI-19Si-5Mg alloys as the raw material adopting the centrifugal casting method were investigated. Structurally, the composites are divided into two zones： a reinforced zone with the high volume fraction of primary Si and Mg2Si particles and an unreinforced zone with no or a few particles. In the reinforced zone, the primary particles are evenly distributed, with the sizes of the primary Si particles 80-120 μm, and that of primary Mg2Si particles 20-50 μm. The properties test results show the reinforced zone has higher Rockwell hardness and better wear resistance than the unreinforced zone, due to the complementary reinforcement relationship between the primary Si and Mg2Si particles and their high volume fraction.

A Novel Technique for Preparation of Electrically Conductive ABS/Cu Polymeric Gradient Composites

A novel technique for preparing functionally gradient electrically conductive polymeric composites was developed by using of solution casting technique on the principle of Stokes＇ law. Acrylonitrile- butadiene-styrene/Cu （ABS/Cu） gradient polymeric composites were prepared successfully using this technique. The gradient structures, electrically conductive performance and mechanical properties of the ABS/Cu composites were investigated. Optical microscope observation shows that the gradient distribution of Cu particles in ABS matrix was formed along their thickness-direction. The electrically conductive testing results indicate that the order of magnitude of surface resistivity was kept in 10^15 Ω at ABS rich side, while that declined to 10^5 Ω at Cu particles rich side, and the percolation threshold was in the range of 2.82 vo1%- 4.74 vol% Cu content at Cu particles rich side. Mechanical test shows that the tensile strength reduced insignificantly as the content of Cu increases owing to the gradient distribution.

AN IN SITU SURFACE COMPOSITE AND GRADIENT MATERIAL OF Al-Si ALLOY PRODUCED BY ELECTROMAGNETIC FORCE

Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.

IN SITU GRADIENT DOUBLE-LAYER COMPOSITES OF Al-Fe ALLOY BY CENTRIFUGAL CASTING

ＩＮＳＩＴＵＧＲＡＤＩＥＮＴＤＯＵＢＬＥＬＡＹＥＲＣＯＭＰＯＳＩＴＥＳＯＦＡｌＦｅＡＬＬＯＹＢＹＣＥＮＴＲＩＦＵＧＡＬＣＡＳＴＩＮＧ①ＷａｎｇＱｕｄｏｎｇ，ＪｉｎＪｕｎｚｅＲｅｓｅａｒｃｈＣｅｎｔｅｒｏｆＦｏｕｎｄｒｙＥｎｇｉｎｅｒｉｎｇ，Ｄａｌ...

Relationship of Purity Gradient and Accumulation with Feed Composition in Two-Component Countercurrent Extraction System

Ａｃｃｕｍｕｌａｔｉｏｎ，ａｂａｓｉｃｐａｒａｍｅｔｅｒｉｎｓｏｌｖｅｎｔｅｘｔｒａｃｔｉｏｎｐｒｏｃｅｓ，ｗａｓｉｎｔｒｏｄｕｃｅｄｉｎｔｈｅｄｙｎａｍｉｃｓｉｍｕｌａｔｉｏｎ．Ｐｕｒｉｔｙｏｆｐｒｏｄｕｃｔｓ，ａｃｕｍｕｌａｔｉｏｎｏｆｅａｃ...

Oxidation Behavior of C/C-SiC Gradient Matrix Composites

Oxidation behavior of C/C-SiC gradient matrix composites and C/C composites were compared in stationary air. The results show that oxidation threshold of C-SiC materials increases with the amount of SiC particles in the codeposition matrix. Oxidation rate of C/C-SiC gradient matrix composites is significantly lower than that of C/C material. The micro-oxidation process was observed by SEM.

Tropical tree community composition and diversity variation along a volcanic elevation gradient

Unraveling the factors that determine variation of diversity in tropical mountain systems is a topic for debate in plant ecology.This is especially true in areas where topography is complex due to volcano elevational gradients and where forests are vulnerable to human activity.In this study we used a set of climatic(temperature,rainfall,and radiation solar),topographic(elevation,slope aspect,and slope orientation)and human disturbance variables to determine their effect on diversity and composition patterns of a tree community,considering three slope aspects of a tropical volcano in southeastern Mexico.We sampled trees in seventy 0.1-ha plots distributed on three slope aspects of the Tacanávolcano along an elevational gradient of 1500 to 2500 m.We determined diversity patterns(general tree richness,exponential of Shannon index,and pioneer species richness)with linear regression models,and for beta diversity,we used a dissimilarity index(within and between elevational bands 100 m wide).The effect of a set of environmental and human disturbance variables on tree diversity and community composition was analyzed with general linear models and multivariate analyses,respectively.We registered 2,949 individual trees belonging to 176 species and 58families.The average species richness and alpha diversity per plot were 13(standard deviation±6)and 9(±5),respectively.General tree richness and alpha diversity increased in the middle part(unimodal patterns)of the elevational gradient,but pioneer species richness decreased linearly with elevation.The variance explained by general linear models was greater in richness(32%)than in alpha diversity(25.3%).The most important predictor variables were temperature(elevational gradient),which explained the unimodal pattern(richness and alpha diversity increase at intermediate levels of temperature),and slope orientation,which explained the increase in richness and alpha diversity toward the geographic north.Only temperature had a significant effect on pioneer species diversity(22%).For community composition,all the predictor variables evaluated had a significant effect,but the most important were slope aspect and temperature.Assemblages were almost completely different in plots that were farther apart along the elevation gradient and had different slope aspects.Finally,the forests at lower elevations(1500–1900 m)were those that had the most human disturbance.Our study reveals the importance of considering a set of environmental variables related to climate,topography(e.g.,slope aspect),and human disturbance to understand variation in diversity and composition of a tree community on a tropical volcano.With this information,we believe that it is important to implement conservation and restoration measures in the forests of the lower parts of the Tacanávolcano,complemented by studies that contribute to designing better conservation strategies.

Characteristics of two Al based functionally gradient composites reinforced by primary Si particles and Si/in situ Mg_2Si particles in centrifugal casting

Two kinds of Al based functionally gradient composite tubes reinforced by primary Si particles alone and primary Si/in situ Mg2Si particles jointly were successfully prepared by centrifugal casting,and their structural and mechanical characters were compared.It is found that the composite reinforced with primary Si particles takes a characteristic of particles distribution both in the inner and outer layers.However,composite reinforced with primary Si/Mg2Si particles jointly takes a characteristic of particles distribution only in the inner layer and shows a sudden change of particles distribution across the section of inner and outer layers.The hardness and wear resistance of Al-19Si-5Mg tube in the inner layer are greatly higher than that in the other layers of Al-19Si-5Mg tube and Al-19Si tube.Theoretical analysis reveals that the existence of Mg2Si particles is the key factor to form this sudden change of gradient distribution of two kinds of particles.Because Mg2Si particles with a lower density have a higher centripetal moving velocity than primary Si particles,in a field of centrifugal force,they would collide with primary Si particles and then impel the later to move together forward to the inner layer of the tube.

On the homogenization of metal matrix composites using strain gradient plasticity

The homogenized response of metal matrix composites（MMC） is studied using strain gradient plasticity.The material model employed is a rate independent formulation of energetic strain gradient plasticity at the micro scale and conventional rate independent plasticity at the macro scale. Free energy inside the micro structure is included due to the elastic strains and plastic strain gradients. A unit cell containing a circular elastic fiber is analyzed under macroscopic simple shear in addition to transverse and longitudinal loading. The analyses are carried out under generalized plane strain condition. Micro-macro homogenization is performed observing the Hill-Mandel energy condition,and overall loading is considered such that the homogenized higher order terms vanish. The results highlight the intrinsic size-effects as well as the effect of fiber volume fraction on the overall response curves, plastic strain distributions and homogenized yield surfaces under different loading conditions. It is concluded that composites with smaller reinforcement size have larger initial yield surfaces and furthermore,they exhibit more kinematic hardening.

Preparation and dielectric properties of compositionally graded (Ba,Sr)TiO_3 thin film by sol-gel technique

Compositional graded BaxSr1-xTiO3 (x=0.6, 0.7, 0.8, 0.9, 1.0) (BST) thin films (less than 400 nm) were fabricated on Si and Pt/Ti/SiO2/Si substrates by sol-gel technique. A special heating treatment was employed to form the uniform composition gradients at 700 ℃. The microstructures of the films were studied by means of X-ray diffraction, atomic force microscope and field emission scanning electron microscopy. The results show that the films have uniform and crack-free surface morphology with perovskite structure phase. The small signal dielectric constant (εr) and dielectric loss (tan δ) are found to be 335 and 0.045 at room temperature and 200 kHz. The dielectric properties change significantly with applied dc bias, and the graded thin film show high tunability of 42.3% at an applied field of 250 kV/cm. All the results indicate that the graded BST thin films prepared by sol-gel technique have a promising candidate for microelectronic device.

Effect of pH Value on Nano-Al_2O_3/Ni+Co Gradient Bionic Composite Coating by Electrodeposition

The metal and nano-ceramic composite coatings were formed on gray cast iron surface by electrodepositon method.The Ni-Co was used as metal matrix,and the nano-Al2O3 was chosen as second-phase particulates.The gradient structure of biology material was the model to avoid bad interface bonding and stress distribution,therefore the gradient composite coating was prepared.The morphology of composite coatings was flatter and the microstructure was more com-pact than the pure Ni-Co coatings.Effect of pH value on surface morphology was analyzed,which some microcracks appeared when pH value was greater than 5.The content of codeposition na-no-Al2O3 reached a maximum value at pH value of 3-4,at the same time the properties including mi-crohardness and wear-resistance were analyzed.The result indicated that the mirohardness reached a maximum value and the wear loss volume was less at pH value 3-4.

Effect of plastic deformation on microstructure and hardness of AlSi/Al gradient composites

The effects of plastic deformation on the evolution of microstructure and micro-hardness were studied on plates made from a cylindrical ingot of AlSi/Al aluminum composite. This ingot was produced by double-stream-pouring continuous casting(DSPCC). The results show that the three layers, i.e. the external pure aluminum, internal Al-Si alloy and the transition gradient layer, are maintained after compression as well as rolling processing. With the decrease in thickness of the gradient composite plate, the fluctuation of micro-hardness in transition layer in the direction normal to the applied force is significantly reduced. A simplified lamination model was used to evaluate qualitatively the micro-hardness distribution in the direction parallel to the applied force. However, the model is invalid in the explanation of the fluctuation of the micro-hardness in the direction normal to the applied force. The micro-hardness distribution variation in this direction is mainly attributed to the deformation of α(Al) matrix incorporated the dissolution and spheroidization of eutectic silicon phase.

The Study for the Reinforced Composites of Textile Gradient Structure

Based on references, this paper further develops the composites of textile gradient structure, tests and analyses the mechanical properties of composites of gradient struture, moreover, makes a comparison between composites of gradient structure and common laminated composites.

THEORETICAL ANALYSIS OF PARTICLE DISTRIBUTION IN GRADIENT COMPOSITE BY CENTRIFUGAL CASTING

A theoretical analysis was presented to produce gradient composite by centrifugal casting. Particle movement in liquid metal is described and gradient distribution of particles in composite is calculated in a centrifugal field. The factors affected the gradient distribution are discussed in detail. There exist composite zone and blank zone in gradient composite, which was proved by experiments. Finally, a theoretical analysis is given to explain the above mentioned particle distribution.