The component, hardness, density and microstructure of typical glass mould materials made in developed countries are analyzed. It is shown that glass mould material made by Jiangsu Changshu Orient Mold and Die Co Ltd ...The component, hardness, density and microstructure of typical glass mould materials made in developed countries are analyzed. It is shown that glass mould material made by Jiangsu Changshu Orient Mold and Die Co Ltd differs from that from the developed countries. The way to improve Orient Glass Mold materials was introduced. KDT-1 type mold material with Dtype graphite was produced.展开更多
The bulk Fe<sup>60 CoxZr<sup>10 Mo5W2B<sup>23-x （x=1, 3, 5, 7, 9） amorphous rods with diameters of 1.5 mm were successfully prepared by copper mold casting method with the low purity raw materials....The bulk Fe<sup>60 CoxZr<sup>10 Mo5W2B<sup>23-x （x=1, 3, 5, 7, 9） amorphous rods with diameters of 1.5 mm were successfully prepared by copper mold casting method with the low purity raw materials. The amorphous and crystalline states, and thermal parameters, such as the glass transition temperature （Tg）, the initial crystallization temperature （Tx）, the supercooled liquid region （ΔTx=Tx-Tg）, the reduced glass transition temperature T<sup>rg （Tg/Tm, Tm: the onset temperature of melting of the alloy, and Tg/Tl, Tl: the finished temperature of melting of the alloy） were investigated by X-ray diffractometry （XRD） and differential scanning calorimetry （DSC） analysis. Glass forming ability of Fe<sup>60 CoxZr<sup>10 Mo5W2B<sup>23-x （x=1,3,5,7,9） bulk metallic glasses has been studied. According to the results, the alloy （x=7） with the highest T<sup>rg （Tg/Tl=0.607, Tg/Tl=0.590） value, has the strongest glass forming ability among these alloys because its composition is near eutectic composition. The wide supercooled liquid region over 72 K indicates the high thermal stability for this alloy system. This bulk metallic glass exhibits quite high strength （Hv 1020）. The success of production of the Fe-based bulk metallic glass with industrial materials is of great significance for the future progress of basic research and practical application.展开更多
We investigated the deformation behaviors of Zr_65Cu_17.5Ni_10Al_7.5 in superplastic forming in silicon mould via numerical modeling and experiments. The data needed for the constitutive formulation were obtained from...We investigated the deformation behaviors of Zr_65Cu_17.5Ni_10Al_7.5 in superplastic forming in silicon mould via numerical modeling and experiments. The data needed for the constitutive formulation were obtained from compressive tests to establish a material library for finite-element simulation using a DEFORM 3D software. A constant speed forming process of a micro gear was modeled where the loading force, feature size and amount of deformation in the micro gear in silicon mould were analyzed in detail for the optimal requirements of micro gear forming and the protection of silicon mould. Guided by the modeling parameters, an amorphous metal micro gear was successfully obtained by our home-made superplastic forming system with the optimized parameters （temperature of 683 K, top speed of 0.003 mm/s until the load force reaching limiting value at 1960 N, and a gradually decelerating process for holding the force to the end）. Our work gives a good example for optimization of superplastic forming and fabrication of BMGs in microparts.展开更多
文摘The component, hardness, density and microstructure of typical glass mould materials made in developed countries are analyzed. It is shown that glass mould material made by Jiangsu Changshu Orient Mold and Die Co Ltd differs from that from the developed countries. The way to improve Orient Glass Mold materials was introduced. KDT-1 type mold material with Dtype graphite was produced.
文摘The bulk Fe<sup>60 CoxZr<sup>10 Mo5W2B<sup>23-x （x=1, 3, 5, 7, 9） amorphous rods with diameters of 1.5 mm were successfully prepared by copper mold casting method with the low purity raw materials. The amorphous and crystalline states, and thermal parameters, such as the glass transition temperature （Tg）, the initial crystallization temperature （Tx）, the supercooled liquid region （ΔTx=Tx-Tg）, the reduced glass transition temperature T<sup>rg （Tg/Tm, Tm: the onset temperature of melting of the alloy, and Tg/Tl, Tl: the finished temperature of melting of the alloy） were investigated by X-ray diffractometry （XRD） and differential scanning calorimetry （DSC） analysis. Glass forming ability of Fe<sup>60 CoxZr<sup>10 Mo5W2B<sup>23-x （x=1,3,5,7,9） bulk metallic glasses has been studied. According to the results, the alloy （x=7） with the highest T<sup>rg （Tg/Tl=0.607, Tg/Tl=0.590） value, has the strongest glass forming ability among these alloys because its composition is near eutectic composition. The wide supercooled liquid region over 72 K indicates the high thermal stability for this alloy system. This bulk metallic glass exhibits quite high strength （Hv 1020）. The success of production of the Fe-based bulk metallic glass with industrial materials is of great significance for the future progress of basic research and practical application.
基金Funded by the National Natural Science Foundation of China(Nos.51222508,51175211)
文摘We investigated the deformation behaviors of Zr_65Cu_17.5Ni_10Al_7.5 in superplastic forming in silicon mould via numerical modeling and experiments. The data needed for the constitutive formulation were obtained from compressive tests to establish a material library for finite-element simulation using a DEFORM 3D software. A constant speed forming process of a micro gear was modeled where the loading force, feature size and amount of deformation in the micro gear in silicon mould were analyzed in detail for the optimal requirements of micro gear forming and the protection of silicon mould. Guided by the modeling parameters, an amorphous metal micro gear was successfully obtained by our home-made superplastic forming system with the optimized parameters （temperature of 683 K, top speed of 0.003 mm/s until the load force reaching limiting value at 1960 N, and a gradually decelerating process for holding the force to the end）. Our work gives a good example for optimization of superplastic forming and fabrication of BMGs in microparts.
