Different fragments of a hot-rolled and homogenized Cu–Zn–Al shape memory alloy（SMA） were subjected to thermal cycling by means of a differential scanning calorimetric（DSC） device. During thermal cycling, heatin...Different fragments of a hot-rolled and homogenized Cu–Zn–Al shape memory alloy（SMA） were subjected to thermal cycling by means of a differential scanning calorimetric（DSC） device. During thermal cycling, heating was performed at the same constant rate of increasing temperature while cooling was carried out at different rates of decreasing temperature. For each cooling rate, the temperature decreased in the same thermal interval. During each cooling stage, an exothermic peak（maximum） was observed on the DSC thermogram. This peak was associated with forward martensitic transformation. The DSC thermograms were analyzed with PROTEUS software： the critical martensitic transformation start（Ms） and finish（Mf） temperatures were determined by means of integral and tangent methods, and the dissipated heat was evaluated by the area between the corresponding maximum plot and a sigmoid baseline. The effects of the increase in cooling rate, assessed from a calorimetric viewpoint, consisted in the augmentation of the exothermic peak and the delay of direct martensitic transformation. The latter had the tendency to move to lower critical transformation temperatures. The martensite plates changed in morphology by becoming more oriented and by an augmenting in surface relief, which corresponded with the increase in cooling rate as observed by scanning electron microscopy（SEM） and atomic force microscopy（AFM）.展开更多
A six-parameter mathematical model was introduced to simulate the stress-strain hysteresis and the sinner hysteresis of polycrystalline shape memory alloys (SMAs). By the comparison with experiments of Cu-Zn-Al SMA, i...A six-parameter mathematical model was introduced to simulate the stress-strain hysteresis and the sinner hysteresis of polycrystalline shape memory alloys (SMAs). By the comparison with experiments of Cu-Zn-Al SMA, it was shown that the model could be used to calculate the stress-strain relations with rather good accuracy. Moreover, it was found that the six parameters introduced in this paper represented the characteristics of the stress-strain hysteresis of polycrystalline SMAs and could be used to characterize the hysteresis quantitatively.展开更多
The influence of aging on the microstructure and mechanical properties of Cu-11.6wt%Al-3.9wt%Ni-2.5wt%Mn shape memory alloy（SMA） was studied by means of scanning electron microscopy（SEM）,transmission electron micr...The influence of aging on the microstructure and mechanical properties of Cu-11.6wt%Al-3.9wt%Ni-2.5wt%Mn shape memory alloy（SMA） was studied by means of scanning electron microscopy（SEM）,transmission electron microscopy（TEM）,X-ray diffractometer,and differential scanning calorimeter（DSC）.Experimental results show that bainite,γ2,and α phase precipitates occur with the aging effect in the alloy.After aging at 300°C,the bainitic precipitates appear at the early stages of aging,while the precipitates of γ2 phase are observed for a longer aging time.When the aging temperature increases,the bainite gradually evolves into γ2 phase and equilibrium α phase（bcc） precipitates from the remaining parent phase.Thus,the bainite,γ2,and α phases appear,while the martensite phase disappears progressively in the alloy.The bainitic precipitates decrease the reverse transformation temperature while the γ2 phase precipitates increase these temperatures with a decrease of solute content in the retained parent phase.On the other hand,these precipitations cause an increasing in hardness of the alloy.展开更多
The effect of aging treatment on the superelasticity and martensitic transformation critical stress in columnar-grained Cu_（71）Al_（18）Mn_（11） shape memory alloy（SMA） at the temperature ranging from 250°C ...The effect of aging treatment on the superelasticity and martensitic transformation critical stress in columnar-grained Cu_（71）Al_（18）Mn_（11） shape memory alloy（SMA） at the temperature ranging from 250°C to 400°C was investigated. The microstructure evolution during the aging treatment was characterized by optical microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The results show that the plate-like bainite precipitates distribute homogeneously within austenitic grains and at grain boundaries. The volume fraction of bainite increases with the increase in aging temperature and aging time, which substantially improves the martensitic transformation critical stress of the alloy, whereas the bainite only slightly affects the superelasticity. This behavior is attributed to a coherent relationship between the bainite and the austenite, as well as to the bainite and the martensite exhibiting the same crystal structure. The variations of the martensitic transformation critical stress and the superelasticity of columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with aging-temperature and aging time are described by the Austin-Rickett equation, where the activation energy of bainite precipitation is 77.2 kJ ·mol1. Finally, a columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with both excellent superelasticity（5%-9%） and high martensitic transformation critical stress（443-677 MPa） is obtained through the application of the appropriate aging treatments.展开更多
The pseudoelastic elongation (P.E.) of β-phase in Cu-Zn-Al SMA (shape memory alloy) was estimated by using the orientation dependence of transformation strain (Taylor model) and texture analysis. It was found that th...The pseudoelastic elongation (P.E.) of β-phase in Cu-Zn-Al SMA (shape memory alloy) was estimated by using the orientation dependence of transformation strain (Taylor model) and texture analysis. It was found that the pseudoelastic elongation is closely related to f(g) of the (001) ?110? texture component in the CuZnAl SMA sheet. The stronger the (001) ?110? texture, the higher value of pseudoelastic elongation is. For the wires, the estimated pseudoelastic elongation decreases with increasing reduction.展开更多
By adding copper to increase the performance,the Ni-Ti-Cu Shape Memory Alloy(SMA),has been widely used in the field of engineering in recent years.A thermodynamic constitutive model for Ni-Ti-Cu SMA considering differ...By adding copper to increase the performance,the Ni-Ti-Cu Shape Memory Alloy(SMA),has been widely used in the field of engineering in recent years.A thermodynamic constitutive model for Ni-Ti-Cu SMA considering different copper contents is established in this work.Numerical results for two different copper contents,as examples,are compared with the experimental results to verify the accuracy of the theoretical work.Based on the verified constitutive model,the effects of different copper content on the mechanical properties of Ni-Ti-Cu SMA and the tensile and compressive asymmetric properties of Ni-Ti-Cu SMA are finally discussed,respectively.展开更多
In the paper, a melt extraction method was used to fabricate Cu–4Ni–14Al（wt%） fiber materials with diameters between 50 and 200 μm. The fibers exhibited superelasticity and temperature-induced martensitic transfo...In the paper, a melt extraction method was used to fabricate Cu–4Ni–14Al（wt%） fiber materials with diameters between 50 and 200 μm. The fibers exhibited superelasticity and temperature-induced martensitic transformation. The microstructures and superelasticity behavior of the fibers were studied via scanning electron microscopy（SEM） and a dynamic mechanical analyzer（DMA）, respectively. Appropriate heat treatment further improves the plasticity of Cu-based alloys. The serration behavior observed during the loading process is due to the multiple martensite phase transformation.展开更多
基金supported by the project PN-II-ID-PCE-2012-4-0033,contract 13/2013
文摘Different fragments of a hot-rolled and homogenized Cu–Zn–Al shape memory alloy（SMA） were subjected to thermal cycling by means of a differential scanning calorimetric（DSC） device. During thermal cycling, heating was performed at the same constant rate of increasing temperature while cooling was carried out at different rates of decreasing temperature. For each cooling rate, the temperature decreased in the same thermal interval. During each cooling stage, an exothermic peak（maximum） was observed on the DSC thermogram. This peak was associated with forward martensitic transformation. The DSC thermograms were analyzed with PROTEUS software： the critical martensitic transformation start（Ms） and finish（Mf） temperatures were determined by means of integral and tangent methods, and the dissipated heat was evaluated by the area between the corresponding maximum plot and a sigmoid baseline. The effects of the increase in cooling rate, assessed from a calorimetric viewpoint, consisted in the augmentation of the exothermic peak and the delay of direct martensitic transformation. The latter had the tendency to move to lower critical transformation temperatures. The martensite plates changed in morphology by becoming more oriented and by an augmenting in surface relief, which corresponded with the increase in cooling rate as observed by scanning electron microscopy（SEM） and atomic force microscopy（AFM）.
文摘A six-parameter mathematical model was introduced to simulate the stress-strain hysteresis and the sinner hysteresis of polycrystalline shape memory alloys (SMAs). By the comparison with experiments of Cu-Zn-Al SMA, it was shown that the model could be used to calculate the stress-strain relations with rather good accuracy. Moreover, it was found that the six parameters introduced in this paper represented the characteristics of the stress-strain hysteresis of polycrystalline SMAs and could be used to characterize the hysteresis quantitatively.
文摘The influence of aging on the microstructure and mechanical properties of Cu-11.6wt%Al-3.9wt%Ni-2.5wt%Mn shape memory alloy（SMA） was studied by means of scanning electron microscopy（SEM）,transmission electron microscopy（TEM）,X-ray diffractometer,and differential scanning calorimeter（DSC）.Experimental results show that bainite,γ2,and α phase precipitates occur with the aging effect in the alloy.After aging at 300°C,the bainitic precipitates appear at the early stages of aging,while the precipitates of γ2 phase are observed for a longer aging time.When the aging temperature increases,the bainite gradually evolves into γ2 phase and equilibrium α phase（bcc） precipitates from the remaining parent phase.Thus,the bainite,γ2,and α phases appear,while the martensite phase disappears progressively in the alloy.The bainitic precipitates decrease the reverse transformation temperature while the γ2 phase precipitates increase these temperatures with a decrease of solute content in the retained parent phase.On the other hand,these precipitations cause an increasing in hardness of the alloy.
基金financially supported by the National Natural Science Foundation of China (Nos. 51574027 and 51604206)the Financial Support from the State Key Laboratory for Advanced Metals and Materials (No. 2016Z-22)
文摘The effect of aging treatment on the superelasticity and martensitic transformation critical stress in columnar-grained Cu_（71）Al_（18）Mn_（11） shape memory alloy（SMA） at the temperature ranging from 250°C to 400°C was investigated. The microstructure evolution during the aging treatment was characterized by optical microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The results show that the plate-like bainite precipitates distribute homogeneously within austenitic grains and at grain boundaries. The volume fraction of bainite increases with the increase in aging temperature and aging time, which substantially improves the martensitic transformation critical stress of the alloy, whereas the bainite only slightly affects the superelasticity. This behavior is attributed to a coherent relationship between the bainite and the austenite, as well as to the bainite and the martensite exhibiting the same crystal structure. The variations of the martensitic transformation critical stress and the superelasticity of columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with aging-temperature and aging time are described by the Austin-Rickett equation, where the activation energy of bainite precipitation is 77.2 kJ ·mol1. Finally, a columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with both excellent superelasticity（5%-9%） and high martensitic transformation critical stress（443-677 MPa） is obtained through the application of the appropriate aging treatments.
文摘The pseudoelastic elongation (P.E.) of β-phase in Cu-Zn-Al SMA (shape memory alloy) was estimated by using the orientation dependence of transformation strain (Taylor model) and texture analysis. It was found that the pseudoelastic elongation is closely related to f(g) of the (001) ?110? texture component in the CuZnAl SMA sheet. The stronger the (001) ?110? texture, the higher value of pseudoelastic elongation is. For the wires, the estimated pseudoelastic elongation decreases with increasing reduction.
基金support by National Natural Science Foundation of China(No.11502284)Key Deployment Projects of the Chinese Academy of Sciences(KFZD-SW-435)the Fundamental Research Funds for the Central Universities of China(3122020077).
文摘By adding copper to increase the performance,the Ni-Ti-Cu Shape Memory Alloy(SMA),has been widely used in the field of engineering in recent years.A thermodynamic constitutive model for Ni-Ti-Cu SMA considering different copper contents is established in this work.Numerical results for two different copper contents,as examples,are compared with the experimental results to verify the accuracy of the theoretical work.Based on the verified constitutive model,the effects of different copper content on the mechanical properties of Ni-Ti-Cu SMA and the tensile and compressive asymmetric properties of Ni-Ti-Cu SMA are finally discussed,respectively.
基金financial support of the National High Technology Research and Development Program of China (No. 2009AA03Z113)the National Science Foundation of China (No. 51471025)
文摘In the paper, a melt extraction method was used to fabricate Cu–4Ni–14Al（wt%） fiber materials with diameters between 50 and 200 μm. The fibers exhibited superelasticity and temperature-induced martensitic transformation. The microstructures and superelasticity behavior of the fibers were studied via scanning electron microscopy（SEM） and a dynamic mechanical analyzer（DMA）, respectively. Appropriate heat treatment further improves the plasticity of Cu-based alloys. The serration behavior observed during the loading process is due to the multiple martensite phase transformation.
