In this study, production of ct-linoleic acid concentrated from crude perilla oil by gradient cooling urea inclusion was optimized. The fatty acid composition was determined after ethyl esterification by gas chromatog...In this study, production of ct-linoleic acid concentrated from crude perilla oil by gradient cooling urea inclusion was optimized. The fatty acid composition was determined after ethyl esterification by gas chromatography (GC). In this process, orthogonal experiment was carried out. Under optimum conditions, the maximum amount of α-linoleic acid (91.5%) was obtained at a urea to fatty acid ratio of 3, a solvent to fatty acids ratio of 7, a reaction temperature of 348 K and a crystallization time of 690 min. A simple method of gradient cooling urea inclusion was used to purify α-linolenic acid by using urea to form inclusion complexes with the saturated and the less unsaturated fatty acids, which enhanced the purity of α-linoleic acid ethyl ester by above 90%.展开更多
We systematically investigate the polarization gradient cooling (PGC) process in an optical molasses of ultracold cesium atoms. The SR mode for changing the cooling laser, which means that the cooling laser frequenc...We systematically investigate the polarization gradient cooling (PGC) process in an optical molasses of ultracold cesium atoms. The SR mode for changing the cooling laser, which means that the cooling laser frequency is stepped to the setting value while its intensity is ramped, is found to be the best for the PGC, compared with other modes studied. We verify that the heating effect of the cold atoms, which appears when the cooling laser intensity is lower than the saturation intensity, arises from insufficient polarization gradient cooling. Finally, an exponential decay function with a statistical explanation is introduced to explain the dependence of the cold atom temperature on the PGC interaction time.展开更多
In the present work, a unique gradient cooling heat treatment process(GCHT) for a Mn-Si-Cr-B bainitic cast steel was developed, and microstructure and mechanical properties were examined by OM, SEM, EBSD and a uniaxia...In the present work, a unique gradient cooling heat treatment process(GCHT) for a Mn-Si-Cr-B bainitic cast steel was developed, and microstructure and mechanical properties were examined by OM, SEM, EBSD and a uniaxial tensile test. The results showed that the structural-gradient-material(SGM) with a gradient microstructure from granular bainite to martensite was successfully produced, and it exhibited a good ductility(~13.8%) at one end and an excellent ultimate strength(~1,720 MPa) at the other end. In between the bainite and martensite, a transition region with a superior combination of tensile strength and ductility(1,700 MPa and 11.1%) was obtained, which is different from the normal knowledge of a brittle transition region. Moreover, through changing the gradient of cooling rate, the optimized SGM with a new gradient microstructure from pearlite to martensite showed a more stable structural gradient and an improved ductility(22.8%) at one end. The microstructure variation in the sample was mainly related to the carbon diffusion rate during heat treatment, and the diffusion rate could be controlled by regulating the cooling velocity. Therefore, the SGMs with different gradient microstructures could be designed to meet the needs of different properties. As a result, this work provides a new approach for preparation of the gradient structured steel, which has potential for practical application for dual-property automobile parts.展开更多
基金the National Natural Science Foundation of China (20871061)the National 973 Program of China (2008CB617512) for the financial support
文摘In this study, production of ct-linoleic acid concentrated from crude perilla oil by gradient cooling urea inclusion was optimized. The fatty acid composition was determined after ethyl esterification by gas chromatography (GC). In this process, orthogonal experiment was carried out. Under optimum conditions, the maximum amount of α-linoleic acid (91.5%) was obtained at a urea to fatty acid ratio of 3, a solvent to fatty acids ratio of 7, a reaction temperature of 348 K and a crystallization time of 690 min. A simple method of gradient cooling urea inclusion was used to purify α-linolenic acid by using urea to form inclusion complexes with the saturated and the less unsaturated fatty acids, which enhanced the purity of α-linoleic acid ethyl ester by above 90%.
基金supported by the National Basic Research Program of China(Grant Nos.2012CB921603 and 2010CB923103)the International Science &Technology Cooperation Program of China(Grant No.2011DFA12490)+2 种基金the National Natural Science Foundation of China(Grant Nos.11304189,61378015,and 61275209)the Project for Excellent Research Team of the National Natural Science Foundation of China(Grant No.61121064)the Program for Changjiang Scholars,China,and the Innovative Research Team in University,China(Grant No.IRT13076)
文摘We systematically investigate the polarization gradient cooling (PGC) process in an optical molasses of ultracold cesium atoms. The SR mode for changing the cooling laser, which means that the cooling laser frequency is stepped to the setting value while its intensity is ramped, is found to be the best for the PGC, compared with other modes studied. We verify that the heating effect of the cold atoms, which appears when the cooling laser intensity is lower than the saturation intensity, arises from insufficient polarization gradient cooling. Finally, an exponential decay function with a statistical explanation is introduced to explain the dependence of the cold atom temperature on the PGC interaction time.
基金financially supported by the National key research and development program(No.2017YFA0403700)the Natural Science Foundation of China(No.51701080)
文摘In the present work, a unique gradient cooling heat treatment process(GCHT) for a Mn-Si-Cr-B bainitic cast steel was developed, and microstructure and mechanical properties were examined by OM, SEM, EBSD and a uniaxial tensile test. The results showed that the structural-gradient-material(SGM) with a gradient microstructure from granular bainite to martensite was successfully produced, and it exhibited a good ductility(~13.8%) at one end and an excellent ultimate strength(~1,720 MPa) at the other end. In between the bainite and martensite, a transition region with a superior combination of tensile strength and ductility(1,700 MPa and 11.1%) was obtained, which is different from the normal knowledge of a brittle transition region. Moreover, through changing the gradient of cooling rate, the optimized SGM with a new gradient microstructure from pearlite to martensite showed a more stable structural gradient and an improved ductility(22.8%) at one end. The microstructure variation in the sample was mainly related to the carbon diffusion rate during heat treatment, and the diffusion rate could be controlled by regulating the cooling velocity. Therefore, the SGMs with different gradient microstructures could be designed to meet the needs of different properties. As a result, this work provides a new approach for preparation of the gradient structured steel, which has potential for practical application for dual-property automobile parts.