Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of ...Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of as-received one,but moderate ductility between those of ultra-fine grained(UFG) and coarse-grained titanium.Tensile stress-strain curves of SMGT-treated titanium show double strain hardening regimes.The strain hardening rate(dσ/dε) decreases with increasing strain in tensile deformation.The high strain hardening rate at initial yielding is attributed to nano-to-micron-grained surface layer.The low strain hardening rate at large plastic strain regime primarily results from coarse-grained matrix.The SMGT-treated titanium shows a ductile fracture mode with a large number of dimples.The small size of dimples in the treated surface layer is due to the combination of the high strength and strain hardening exponent.The difference between dimple size in nano-to-micron-grained surface layer and coarse-grained matrix is discussed in terms of plastic zone size at the tip of crack in the SMGT-treated titanium.展开更多
The deformation behavior and formability of gradient nano-grained（GNG） AISI 304 stainless steel in uniaxial and biaxial states were investigated by means of tensile test and small punch test（SPT）. The GNG top laye...The deformation behavior and formability of gradient nano-grained（GNG） AISI 304 stainless steel in uniaxial and biaxial states were investigated by means of tensile test and small punch test（SPT）. The GNG top layer was fabricated on coarse grains（CG） AISI 304 by ultrasonic impact treatment. The results showed that the CG substrate could effectively suppress the strain localization of NC in GNG layer, and an approximate linear relationship existed between the thickness of substrate（h） and uniform true strain before necking（ε_（unif））. Grain growth of NC was observed at the stress state with high Stress triaxiality T, which led to better ductility of GNG/CG 304 in SPT, as well as similar true strain after the onset of necking（ε_（neck）） compared with coarse 304 in tensile test. Ei-values of GNG/CG 304 with different structures were nearly the same at different punch speeds, and good formability of GNG/CG 304 was demonstrated. However, punch speed and microstructure needed to be optimized to avoid much lost of membrane strain region in biaxial stress state.展开更多
Gradient ultra-fine grained surface layer in 6063 aluminum alloy was obtained by means of a novel surface self-nanocrystallization technique,namely rotational accelerated shot peening(RASP)treatment.The average grain ...Gradient ultra-fine grained surface layer in 6063 aluminum alloy was obtained by means of a novel surface self-nanocrystallization technique,namely rotational accelerated shot peening(RASP)treatment.The average grain sizes along the vertical section vary from hundreds of nanometers in the top surface to micrometers in the matrix.By using orthogonal experimental design to compare roughness values and hardness values,we synthesized the processing parameters to obtain sample of smaller roughness values and higher hardness.展开更多
The effects of applied normal stress, surface roughness, and initial grain size on the microstructure of pure Cu developed during platen friction sliding deformation （PFSD） processing were investigated. In each case...The effects of applied normal stress, surface roughness, and initial grain size on the microstructure of pure Cu developed during platen friction sliding deformation （PFSD） processing were investigated. In each case, the deformation microstructure was characterized and the hardness of the treated surface layer was measured to evaluate its strength. The results indicated that the thickness of the deformed layer and the hardness at any depth increased with increasing normal stress. A smaller steel platen surface roughness resulted in less microstruc- tural refinement, whereas the microstructural refinement was enhanced by decreasing the surface roughness of the Cu sample. In the case of a very large initial grain size （d 〉 10 mm）, a sharper transition from fine-grain microstructure to undeformed material was obtained in the treated surface layer after PFSD processing.展开更多
破坏水力比降是土体渗透稳定性分析和渗流控制的基础。以渗透变形试验为基础,分析了粗粒土临界水力比降与孔隙比、级配不均匀系数和曲率系数间的相关性。利用Copula理论适合建立多个非独立变量间联合分布函数的优点,构造了拟合粗粒土临...破坏水力比降是土体渗透稳定性分析和渗流控制的基础。以渗透变形试验为基础,分析了粗粒土临界水力比降与孔隙比、级配不均匀系数和曲率系数间的相关性。利用Copula理论适合建立多个非独立变量间联合分布函数的优点,构造了拟合粗粒土临界水力比降crJ、孔隙比e、级配不均匀系数uC和曲率系数cC间相关关系的最优Copula函数,并将其应用于粗粒土临界水力比降估值。结果表明:具有单参数的四维对称Archimedean Copula函数的Nelsen No 6为最优Copula函数。利用构造的最优Copula函数求条件概率,便可得到粗粒土临界水力比降估值的保证率,或者计算在一定保证率条件下临界水力比降估值。通过比较临界水力比降试验值与Copula理论方法、Terzaghi公式及刘杰公式估值,阐述了Copula理论的可靠性,为建立粗粒土临界水力比降与孔隙比及级配特征的多变量统计概率关系及临界水力比降估值提供了一种新途径。展开更多
基金Project(2014CB644003)supported by the National Basic Research Program of ChinaProject(51321003)supported by the National Natural Science Foundation of ChinaProject(B06025)supported by"111"Project of China
文摘Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of as-received one,but moderate ductility between those of ultra-fine grained(UFG) and coarse-grained titanium.Tensile stress-strain curves of SMGT-treated titanium show double strain hardening regimes.The strain hardening rate(dσ/dε) decreases with increasing strain in tensile deformation.The high strain hardening rate at initial yielding is attributed to nano-to-micron-grained surface layer.The low strain hardening rate at large plastic strain regime primarily results from coarse-grained matrix.The SMGT-treated titanium shows a ductile fracture mode with a large number of dimples.The small size of dimples in the treated surface layer is due to the combination of the high strength and strain hardening exponent.The difference between dimple size in nano-to-micron-grained surface layer and coarse-grained matrix is discussed in terms of plastic zone size at the tip of crack in the SMGT-treated titanium.
基金Funded by the National National Natural Science Foundation of China(No.51505189)Open Project of Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment&Technology(No.FM-2015-5)
文摘The deformation behavior and formability of gradient nano-grained（GNG） AISI 304 stainless steel in uniaxial and biaxial states were investigated by means of tensile test and small punch test（SPT）. The GNG top layer was fabricated on coarse grains（CG） AISI 304 by ultrasonic impact treatment. The results showed that the CG substrate could effectively suppress the strain localization of NC in GNG layer, and an approximate linear relationship existed between the thickness of substrate（h） and uniform true strain before necking（ε_（unif））. Grain growth of NC was observed at the stress state with high Stress triaxiality T, which led to better ductility of GNG/CG 304 in SPT, as well as similar true strain after the onset of necking（ε_（neck）） compared with coarse 304 in tensile test. Ei-values of GNG/CG 304 with different structures were nearly the same at different punch speeds, and good formability of GNG/CG 304 was demonstrated. However, punch speed and microstructure needed to be optimized to avoid much lost of membrane strain region in biaxial stress state.
基金funded by NSFC(Grant No.51301092)the National Key R&D Program of China(Grant No.2017YFA0204403)Open Research Fund of Science and Technology on High Strength Structural Materials Laboratory(No.O2016006).
文摘Gradient ultra-fine grained surface layer in 6063 aluminum alloy was obtained by means of a novel surface self-nanocrystallization technique,namely rotational accelerated shot peening(RASP)treatment.The average grain sizes along the vertical section vary from hundreds of nanometers in the top surface to micrometers in the matrix.By using orthogonal experimental design to compare roughness values and hardness values,we synthesized the processing parameters to obtain sample of smaller roughness values and higher hardness.
基金the Danish National Research Foundation (Grant No. DNRF86-5)the National Natural Science Foundation of China (Grant Nos. 51261130091 and 51171085) to the Danish–Chinese Center for Nanometals
文摘The effects of applied normal stress, surface roughness, and initial grain size on the microstructure of pure Cu developed during platen friction sliding deformation （PFSD） processing were investigated. In each case, the deformation microstructure was characterized and the hardness of the treated surface layer was measured to evaluate its strength. The results indicated that the thickness of the deformed layer and the hardness at any depth increased with increasing normal stress. A smaller steel platen surface roughness resulted in less microstruc- tural refinement, whereas the microstructural refinement was enhanced by decreasing the surface roughness of the Cu sample. In the case of a very large initial grain size （d 〉 10 mm）, a sharper transition from fine-grain microstructure to undeformed material was obtained in the treated surface layer after PFSD processing.
文摘破坏水力比降是土体渗透稳定性分析和渗流控制的基础。以渗透变形试验为基础,分析了粗粒土临界水力比降与孔隙比、级配不均匀系数和曲率系数间的相关性。利用Copula理论适合建立多个非独立变量间联合分布函数的优点,构造了拟合粗粒土临界水力比降crJ、孔隙比e、级配不均匀系数uC和曲率系数cC间相关关系的最优Copula函数,并将其应用于粗粒土临界水力比降估值。结果表明:具有单参数的四维对称Archimedean Copula函数的Nelsen No 6为最优Copula函数。利用构造的最优Copula函数求条件概率,便可得到粗粒土临界水力比降估值的保证率,或者计算在一定保证率条件下临界水力比降估值。通过比较临界水力比降试验值与Copula理论方法、Terzaghi公式及刘杰公式估值,阐述了Copula理论的可靠性,为建立粗粒土临界水力比降与孔隙比及级配特征的多变量统计概率关系及临界水力比降估值提供了一种新途径。
