Change in Grain-Size Composition of Lignite under Cyclic Freezing-Thawing and Wetting-Drying

The paper presents the change in grain-size composition of lignite under cyclic freezing-thawing (FTC) and wetting-drying (WDC). The article shows that in the spring and autumn periods the lignites can be subjected to repeated freezing-thawing and wetting-drying, which determines the possibility of changing their grain-size composition and structure. Experimental studies in laboratory conditions on the influence of cyclic freezing-thawing (FTC) and wetting-drying (WDC) on the quality indicators of lignites have been carried out, their granulometric (fractional) composition has been studied. Freezing-thawing cycle conditions are as follows (FTC): minimum exposure temperature: -20°C;maximum: +5°C;relative humidity: 30%;number of processing cycles: 3. Wetting-drying cycles are as follows (WDC): drying temperatures are +20, +40, +60, +80°C, drying time 90 minutes, the coals are further subjected to rain (soaking) for a period of water saturation to humidity of 30% - 40% and dry again. The number of wetting-drying cycles is 3 times. The tests have revealed the destructive effects of FTC and WDC on the samples of lower metamorphic grade coal, and the cycles of wet-dry lead to the much higher yield of fine sizes (-6+0;-13+0 mm) than the cycles of freeze-thaw. Furthermore, it is found that the increase in the yield of fines depends on the heating temperature: coal disintegration proceeds more intensively at a higher temperature of drying.

Multiple grain-size fraction analysis of heavy minerals and the provenance identification of sediments from the abandoned Huanghe River,eastern China

The quantitative analysis of sediment sources in a sink is an important scientific topic and challenge in provenance research.The characteristics of heavy minerals,combined with the geochemical constituents of detrital grains,provide a reliable provenance-tracing approach.We developed a mineral identification method to analyze the multiple grain-size fraction of sediments,from which the elemental geochemistry of hornblende was used to compare the characteristics of sediments from the Huaihe River and Huanghe(Yellow)River in eastern China.Elements that were statistically identified as being able to discriminate sediment provenance were employed to perform a quantitative analysis of the sources of sediments of the abandoned Huanghe River.Results reveal that the Huaihe River is characterized by a high amphibole content of>60%and that the Huanghe and abandoned Huanghe rivers have greater abundances of limonite and carbonate minerals compared with those of the Huaihe River.The contents of trace elements and rare earth elements in hornblende show that the sediments of the abandoned Huanghe River are similar to those of the Huanghe River but different from those of the Huaihe River.Furthermore,chemical mass balance was used to calculate the relative contributions of different provenances of sediment from the abandoned Huanghe River,and nine trace elements of hornblende were identified as discriminators of provenance.Approximately 2%of the hornblende in the abandoned Huanghe River is derived from the Huaihe River and 98%from the Huanghe River.Considering the proportion of hornblende in the total sediment,it is inferred that the contribution of Huaihe River sediment to the abandoned Huanghe River is approximately 0.5%.This study shows that mineral analysis using multiple grain-size fractions(within the wide range of 1Φto 6Φ)with assessment in elemental geochemistry of hornblende can characterize the provenance of fluvial material in coastal zones.

Grain-size characteristics of linear dunes on the northern margin of Qarhan Salt Lake, northwestern China

In order to clarify the formation mechanism of linear dunes on the northern margin of Qarhan Salt Lake, northwestern China, we analyzed the grain-size and sorting parameters of the dune and interdune sands. The surface sands （0-30 ram） from the dune base to the crest of both flanks and interdune corridors were sampled along transects from upwind to downwind through the dune field. The results indicated that the grain-size distribution differed at different positions between and within the dunes. The frequency curve for dune sands mainly showed a bimodal distribution, while the interdune sediments showed a trimodal distribution. The grain size distribution of the linear dunes showed a finer crest pattern, i.e. the crests were composed of sands that were generally finer, better sorted than those of base sands. In addition, at the dune field scale, the dune crest sands were tending to become much finer but sorting became worse along the downwind transects. However, the grain-size parameters of sediments in the interdune corridors showed no clear pattern. The results demonstrated that the grain size and sorting parameters exhibited a systematic change not only at the individual scale but also at the dune field scale. Our results quantitatively estimate the limited role of cohesive sediments on the formation of linear dune under unidirectional wind regime. More attention should be paid to a long-term wind regime observation, internal sedimentary structures and their formation ages.

Sediment texture and grain-size implications: the Changjiang subaqueous delta

Sediment cores were collected from the subaqueous delta of the Changjiang Estuary. Sediment grain-size profiles and their fractal dimensions were analyzed, to elucidate responses to long-term sedimentary processes. In addition, the environmental sensitive populations of grain size have been extracted. The sediment cores can be divided into two parts, according to the sedimentary structures present. The upper part （0-12 cm） is interpreted as being the active layer, which is influenced frequently by changes in the short-term hydrodynamic environment. The lower part extends from a depth of 12 cm, to the bottom of the core. The pattern of fluctuation is linked to sediment grain size. Moreover, two grain-size sensitive populations can be identified. The fine sensitive population is 6.0-7.2 μm, which is a similar grain size to the suspended sediment from up-river. The coarse sensitive population varies from 40.7 to 57.5 μm, revealing complex changes. Thus, the riverine inputs from the Changjiang River may be an important source, which contributes to seasonal fluctuations of grain-size distribution, over the area. The sediments, with grain-sizes ranging from 0.9 to 20.3 μm, are characterised by self-similar in the fractal non-scale region. The fraetal dimension is eonsistant with the grain-size parameter varatioins, which could be used as a replacement index to reveal and reconstruct the sedimentary environmental evolution.

Grain-size Characteristics of Sediment in Daniugou Peatland in Changbai Mountains,Northeast China:Implications for Atmospheric Dust Deposition

The grain-size distribution characteristics and grain-size parameters of sediment in two vertical sections of Daniugou peatland in the Changbai Mountains were systematically investigated.A comparative analysis of the sediment granularity using a discriminative function with Hongyuan peat,red clay,loess-paleosol,fluvial deposit as well as lacustrine deposit was also conducted.It turns out that the vertical section of Daniugou peat ash is primarily constituted by clay and silt particles,and the content of sand is relatively small.Grain-size frequency curves generally show a single-peak modality while a bimodal pattern is detected in the upper layer.The grain-size component and peak pattern of grain-size frequency curves also illustrate that peat ash materials were transported to the peatland by long-range aeolian dust during the deposition process,while there existed short-distance dust influence in peat deposition of the upper layer.Comparisons of grain-size parameters and the discriminative Y-value of Daniugou peat ash with those of typical aeolian sediments show close similarities,suggesting the possibility that atmospheric dust transport processes were involved in the accumulation of peat again.Moreover,the variations of grain-size distribution suggest the local environmental deterioration which is just the driving force of local dust elevation.Grain-size analysis of peatland sediment is demonstrated to be one effective method to extract information about regional and global environmental evolution,and more attention should be paid to current local ecological environment and to seeking a balance between economic development and environmental protection in Northeast China.

Grain-size cycles in Salawusu River valley since 150 ka BP

The palaeo-mobile dune sands and fluvio-lacustrine facies with palaeosols in Milanggouwan stratigraphic section of the Salawusu River valley situated at the southeast of the Mu Us Desert experienced abundant remarkable alternative changes of coarse and fine rhythms in grain-size since 150 ka BP, and the grain-size parameters Mz,σ, Sk, Kg and SC/D also respond to the situation of multi-fluctuational alternations between peak and valley values. Simultaneity the grain-size eigenvalues F5, F16, F25, F50, F75, F84 and F95 are respondingly manifested as greatly cadent jumpiness. Hereby, the Milanggouwan section can be divided into 27 grain-size coarse and fine sedimentary cycles, which can be regarded as a real and integreted record of climate-geological process of desert vicissitude resulted from the alternative evolvement of the ancient winter and summer monsoons of East Asia since 150 ka BP.

Grain-size distribution patterns of suspended sediment in response to hydrodynamics on the Dafeng intertidal flat, Jiangsu, China

Patterns of grain-size distributions of suspended sediment in relation to resuspension, settling, and tidal processes are investigated, based on in situ measurements over the Dafeng intertidal flat, on the Jiangsu coast, in the summer of 2002 and 2003. The suspended sediment here is dominated by fine and very fine silt, with a mean grain-size of 7 - 13 μm. The patterns of the grainsize distributions of suspended sediment during a tidal cycle are characterized by two types： one stable type representing insignificant spatial and temperal variations; and the other bimedal type with significant variations. The main factors influencing the grainsize distributions include resnspension, settling, suspended sediment imported into intertidal flats during the flood phase, and the grain-size distribution of seabed sediment. Resuspension increases the coarse particle content, enhances the mean grain-size of suspended sediment, and results in grain-size distributions for the suspended sediment similar to those of seabed sediment; the settling process has opposite effects on the suspended sediment. When resuspension occurs, the gain-size distributions of suspended sediment in the lower part of water column respond significantly to the current velocity. Where the influence of resuspension and settling processes is weak, the grain-size distributions of suspended sediment appear to be stable and almost identical for the various parts of intertidal flats during different measurement periods. Such distributions are referred to the background grain-size distribution, for which the mean grain-size over the Dafeng intertidal flat is around 7 μm.

Grain-size Characteristics and Climate Variability in TMS5e Sequence of Tumen Section in Southern Tengger Desert,Northwestern China

The TMS5e sequence from the Tumen section, at the southern edge of Tengger Desert in the northwestern China, is synchronous with Marine Isotope Stage 5e （MIS5e）. It consists of 16 layers of aeolian dune sands, 11 layers of lacustrine loess-like facies, and 5 layers of lacustrine facies. The results of grain-size analysis shows that the pa- laeo-mobile dune sands, palaeo-fixed to semi-fixed dune sands and loess-like sandy loams are mainly composed of sands, ranging from 70% to 96%; their silt contents ranged from 4% to 20%, and their clay contents ranged from 1% to 5%; the climate under which the aeolian dune sands were deposited is similar to that under which modern mobile dune sands form, which is caused by the dominance of the cold, dry East Asian winter monsoon. In contrast, the lacustrine loess-like facies and lacustrine facies had a lower sand contents than those of the three aeolian dune sands, but have higher silt and clay contents, most of their sand content ranged from 30% to 60%, their silt contents ranged from 35% to 55%, and their clay contents ranged from 6% to 20%. The lacustrine loess-like facies and lacustrine facies formed under the influence of the warm, humid East Asian summer monsoon based on their similarity with modern sediments. The grain-size indicator Mz （mean grain diameter） and the SC/D value in the TMS5e sequence indicate climatic insta- bility at the southern edge of the Tengger Desert during MIS5e, with at least 14 fluctuations between a warm, humid climate and a cold, dry climate, divided into five stages： TMS5e5 （139 kyr to 129.3 kyr B.P.）, TMS5e4 （129.3 kyr to 124 kyr B.P.）, TMS5e3 （124 kyr to 119.5 kyr B.P.）, TMS5e2 （119.5 kyr to 116.5 kyr B.P.）, and TMS5el （116.5 kyr to 113.7 kyr B.P.）. These correspond roughly to MIS5e5, MIS5e4, MIS5e3, MIS5e2, and MIS5el, respectively, in the GRIP ice core data.

Spatial variation in grain-size population of surface sediments from northern Bering Sea and western Arctic Ocean: Implications for provenance and depositional mechanisms

In general,sediments in nature comprise populations of various diameters.Accurate information regarding the sources and depositional mechanisms of the populations can be obtained through their temporal and spatial comparisons.In this study,the grain size distribution of surface sediments from the Bering Sea and western Arctic Ocean were fitted and partitioned into populations using a log-normal distribution function.The spatial variations in the populations indicate differences in their sources and deposition mechanisms.The sediments on most of the Bering Sea Shelf originated from the Yukon River,and were transported westward by waves and currents.However,the presence of a coarser population outside Anadyr Bay was the result of Anadyr River transport.Additionally,a northward transport trend of fine suspended particles was observed on the west side of the Bering Sea Shelf.The sediments in Hope Valley in the south Chukchi Sea also originated from the Yukon River.The coarser population on the central Chukchi Sea Shelf originated from coast of Alaska to the east,not the Yukon River,and was transported by sea ice and bottom brine water.The populations of sediments from the Chukchi Basin and the base of the Chukchi Sea Slope are the result of sea ice and eddy action.Surface sediments from the western high Arctic Ocean predominantly comprised five populations,and two unique populations with mode diameters of 50–90μm and 200–400μm,respectively,were ubiquitous in the glacial and interglacial sediments.It was difficult to distinguish whether these two populations originated from sea ice or icebergs.Therefore,caution should be exercised when using either the>63μm or>250μm fractions in sediments as a proxy index for iceberg and ice sheet variation in the high Arctic Ocean.

The grain-size distribution of the suspended particulate matter in the Huanghe Estuary and its adjacent sea area in winter

The grain-size of suspended particulate matter （SPM） in the Huanghe Estuary and its adjacent sea area was investigated with an in situ laser particle size analyzer （LISST-100） in November 2006.The spatial distribution of the grain-size parameters was very complicated.The results show that （1） the mean particle size of SPM ranged from 3.00Φ to 6.41Φ,with an average value of 4.66Φ;（2） the frequency distribution patterns of the SPM grain-size showed three different types,which were mono-mode,dual-mode and tri-mode,respectively;（3） C-M chart suggested that the transportation-processes of the SPM not only included suspended mode,but also the bed load transportation mode.The bed load transportation mode mainly occurred at the bottom layer.The characteristics and space distribution of SPM grain-size might be mainly controlled by sediment discharge of the Huanghe River,hydrodynamics condition,surface sediment types,and biological process within the study area.

Transgressive Events since the Late Pleistocene in the Yellow River Delta: Grain-size Distribution and Palynological Results

This study deals with the relationship between sea-level changes and paleoclimatic fluctuations based on the analysis of stratigraphy, grain sizes, palynology, and radiometric dating of the Yellow River delta since the Late Pleistocene. Evidence from the sedimentary record, grain sizes, and pollen provides a paleoenvironmental history of the Late Pleistocene from the boreholes of the delta. Based on a combination of grain-size analysis with lithological studies, marine deposit units contain the intervals of 13.85–16.9, 18.5–19.69, 27.9–34.8, 36.4–37.2, 48.4–51.6, and 54.1–55.9 m, and transitional facies units contain the intervals of 10.25–13.85, 16.9–18.5, 19.69–27.9, 34.8–36.4, 37.2–48.4, 51.6–54.1, and 55.9–60 m, compared with fluvial(terrestrial facies) deposit units(3.36–10.25 m). Based on pollen analysis and pollen assemblages, there were three warm-wet periods from 9.1–0.16 ka BP, 16.1–60 ka BP, and 90.1–94.6 ka BP From the top to the bottom of the borehole, the paleoclimate has an evident fluctuation: warm and moist(Holocene Optimum) —cool and dry(Younger Dryas Event)—mild semi cool—cool and dry—warm and moist. There were three warm-wet periods from 9.1–0.16 ka BP, 16.1–60 ka BP, and 90.1–94.6 ka BP, corresponding to the Holocene Optimum stage, MIS 3, and MIS 5, respectively. The warm period allowed monsoonal evergreen and broadleaved deciduous forests that corresponded to Holocene hypsithermal climatic conditions and the Late Pleistocene climatic Optimum. Three warm-wet periods occurred in marine deposit units from 9.1–0.16 ka BP, 60.1–16.1 ka BP, and 94.6–90.1 ka BP. These periods correspond to the Cangzhou transgression, Xianxian transgression, and Huanghua transgression, respectively. From 90.1–60.1 ka BP, 17.5–9.1 ka BP, and 0. 16 ka BP–1855 AD, three dry and cold phases are recognized. The phases indicate the fluvial(flood plain) sedimentary environment, corresponding to cooler and mild dry periods based on palynological results and grain-size distribution.

Grain-size features of aeolian sand on the east coast of Hainan Island and the revealed evolutionary processes of the sedimentary environment

The Mudui stratigraphic section represents the typical records of sedimentation processes of sand dunes and interdune depressions on the east coast of Hainan Island.Based on high-density sampling and optically stimulated luminescence(OSL) dating of the strata of the section,the grain-size composition,grain-size parameters,cumulative distribution probability curve,and grain-size-sensitivity indexes(SC/D) were analyzed.The analyzed results show that the grain-size features of aeolian sand,weakly developed sandy paleosol,two-facies(aeolian and aqueous) deposits,and lagoon deposits are all different.This indicates four evolutionary phases of the sedimentary environment of the east coast of Hainan Island since 38 ka B.P.Phase I:38-22 ka B.P.;phase II:22-17 ka B.P.;phase III:17-10 ka B.P.;phase IV:10 ka B.P.-present.The climate experienced the hot-wet/hot-dry,hot-wet/hot-dry,and warm-wet/hot-wet fluctuations,and the sedimentary environment also underwent lagoon deposition,dune and interdune depression deposition,dune stabilization and soil development,shifting sand deposition,and evolutionary processes.

Grain-size distribution characteristics of red sandy sediments in Dongjiang River valley,southern Nanling Mountains,during the MIS2 stage

Layer LJ3 of Linjiang stratigraphic section in Dongjiang River valley in the south of the Nanling Mountains is a set of red sandy sediments.Measured by thermoluminescence(TL) dating,it was found to be formed in MIS2-9,500 ± 800 yr to 19,600 ± 1,800 yr B.P.After analy-sis of the grain sizes of the 16 samples(LJ3-100 to LJ3-85) in this layer,it was discovered that(1) The contents of each grain group in dif-ferent samples are similar.(2) The values of Md,Mz,,Sk,and Kg vary from LJ3-100 to LJ3-85 in a narrow range.(3) The segments of each sample in the accumulative curves extend parallel with similar slopes.All the three aspects reveal the Aeolian characteristics of Layer LJ3.Therefore,it is thought that Layer LJ3 consists of red sandy sediments formed in MIS2 in the south of Nanling Mountain,which reflects the arid climate at that time.

Grain-size Age Model in Reconstructing Orbital-and Suborbital-scale Climate Changes on the Northeastern Tibetan Plateau Since the Late Glacial

Reconstructions of past climatic changes on the northeastern Tibetan Plateau(NETP) can provide insights into the Asian summer monsoon(ASM) variability. However, the regional climate changes on both orbital and suborbital time scales since the late Glacial remain controversial. Here we present the results of high-resolution geochemical and grain-size analyses of a sediment core from Genggahai Lake, a small, shallow lake in this area. Changes of the accumulation rate of the core sediments show a similar trend with variations of the coarse fraction. Accordingly, the chronological framework is constructed using a grain-size age model. In addition, the histories of chemical weathering and aeolian activity since the late Glacial are reconstructed based on the Al/Ti ratios and coarse fractions, respectively. The results suggest that an enhanced chemical weathering and a weakened aeolian activity occurred on the NETP under a warmer, wetter climate during the early to mid-Holocene(11.3–6.3 ka cal BP), compared with the late Glacial(17.1–11.3 ka cal BP) and the late Holocene(6.3 ka cal BP to present), which responded mainly to the strengthened ASM on orbital time scale. In addition, the synchronous occurrences of weakened chemical weathering, low lake level and intense aeolian activity on suborbital time scale reflect several episodes of weakened ASM. Furthermore, these episodes largely coincide with the centennial-to millennial-scale cold events in the North Atlantic, which demonstrates the close connection between the ASM and the cooling at high latitudes.

Vertical grain-size trend of mouth bar in lacustrine fan delta:Flume experiments

Field observational previously indicated a mouth bar of a fan delta could exhibit a fining-or coarseningupward trend,which bring a new challenge to the identification of mouth bar in subsurface studies due to the lack of morphological descriptions.Previous studies have indicated that effluent behavior in rivermouth system can affect the vertical grain-size trend of mouth bar,but the drivers and magnitude of this phenomenon are not understood.We conducted flume experiments to investigate the mechanism and controlling factors of vertical grain-size trend of mouth bar.Experiment with a steeper slope of the substrate layer,greater discharge,higher sediment/water ratio,and coarser sediment induced a finingupward trend of mouth bar,because the effluent was dominated by strong inertia.Mouth bar in the experiment with a gentler slope of the substrate layer,smaller discharge,lower sediment/water ratio,and finer sediment exhibited a coarsening-upward trend dominated by the friction-dominated effluent.The relationship between the vertical grain-size trend of mouth bar and the gradients of foreset bedding in small-scale flume models and the cut-off of 15°-18°are applicable in natural systems.Identifying depositional setting to infer depositional process in river-mouth system and analyzing the plane geometry of sandbodies are two steps in the interpretation of ancient fan deltaic rock record.

Laboratory Application of Laser Grain-Size Analyzer in Determining Suspended Sediment Concentration

Suspended sediment concentration(SSC) is an important parameter in marine sedimentology. With the development of technology, many acoustic and optical devices, such as the Laser In-Situ Scattering and Transmissometry, have been designed to measure in situ SSC and grain size distribution. But due to fund or other restrictions, many experiments were only conducted in laboratory, using an indoor laser grain-size analyzer and gravimetric method to measure grain size distribution and concentration, respectively. In this study the laboratory experiment is simplified by omitting the tiring step of gravimetric method. The connections between SSC and other parameters(obscuration, D50 and sorting index) were investigated based on 124 surface sediment samples collected from different offshore areas. A new method is developed for determining SSC in laboratory using a laser grain-size analyzer.

The grain-size characteristics of Quaternary deposits at Xingshan near Siping in Jilin province, China

This research paper analyses the grain-size characteristics of the Quaternary deposits at Xingshan near Siping, Jilin province in China by employing graphic measures to study the grain size distribution and its mode of transport and deposition. The Quaternary deposits at Xingshan lie unconformable on Cretaceous rocks made of siltstone, mudstone and sandstone. The average grain size is between 8.06 to 8.55Φ (0.002 6 ～0.003 7 mm). The Quaternary deposits at Xingshan mainly compose of very fine silt to clay. The compositions of the grade are clay 63% and silt 37%. The clay size components are weathered debris transported and deposited by flowing water from the SE highlands or hills to the low lying NW Xingshan plains whereas the silty components accumulated by aoelian process. The Quaternary deposits at Xingshan accumulated in the middle and late Pleistocene interglacial periods from (459.12～39.03) ka to (88.92～7.56) ka. The standard deviation ranged from 0.96 to 1.36Φ, indicating that the sediments are moderately to poorly sorted, Coefficient of skewness ranged from 0.16～0.31 with an average skewness of 0.218, (Positively skewed towards fine). Kurtosis values (0.84～1.05) from the grain size distribution and visual inspection of the frequency curves indicate platykurtic to mesokurtic curves and unimodal to bimodal grain-size distribution. The type of deposit formation is sand dune and the source is at a distal from its provenance.

Turbidite Events Recorded in Deep-sea Core IR-GC1 off Western Sumatra： Evidence from Grain-size Distribution

Sediment core IR-GC1, from the abyssal basin of the Indian Ocean off Sumatra, may provide important information on depositional events related to earthquakes and tsunamis. In this study, based on a combination of grain-size analysis with lithological studies and oxygen isotope stratigraphy, seven deep-sea turbidite layers were identified, corresponding to seven turbidity events that occurred at 128- 130, 105-107, 98-100, 86-87, 50-53, 37-41 and 20-29 ka. The sediments of the turbidite deposits are characterized by coarse grain sizes, poor sorting, wide kurtosis, bimodal frequency distributions and clear depositional variations. Particle size grading is also an important signature of deep-sea turbidite deposits and can be used as an indicator to identify turbidite layers. Possible triggering mechanisms for the turbidite events include tsunamis, earthquakes, volcanic eruptions and sea-level changes.

Grain-size and compositional variability of Yarlung Tsangpo sand(Xigaze transect,south Tibet):Implications for sediment mixing by fluvial and aeolian processes

Studying the grain-size dependent compositional variability in modern river sediments provides a key to decipher the information stored in the sedimentary archive and reconstruct the evolution of the Earth’s surface in the past. Bedload sand along the Xigaze cross section of the Yarlung Tsangpo(upper Brahmaputra River) ranges in mean grain size from 0.72 Φ to 3.21 Φ, is moderately to poorly sorted and slightly platykurtic to moderately leptokurtic with sub-angular to sub-spherical grains. Litho-feldspatho-quartzose to feldspatholitho-quartzose sand(Q 43%-65%;F 13%-44%;L 11%-28%) contains 3.4%-14.4% heavy minerals including amphibole(64%-89%), epidote(4%-11%), chloritoid(0-10%), and clinopyroxene(2%-6%). The marked textural and compositional variability observed across the Xigaze transect of the Yarlung Tsangpo mainstem is controlled by both fluvial and aeolian processes, including repeated reworking by westerly and glacial winds,as well as by local contributions from northern and southern tributaries draining the Lhasa Block and the Himalayan Belt, respectively. The modern sedimentary case here will shed new light on interpreting paleogeography and provenance.

Grain-size features of a Miocene loess-soil sequence at Qinan: Implications on its origin

In this study, grain-size of 507 bulk samples from the QA-I Mioceneloess-soil sequence at Qinan were analyzed, and the grain-size features are compared with those oftypical Quaternary loess and soil samples, representative lacustrine and fluvial samples. Theresults indicate that the grain-size distribution pattern of the Miocene loess is essentiallysimilar to that of Quaternary loess, but greatly differs from the lacustrine and fluvial sediments.Loess layers are regularly coarser than soil layers, indicating cyclical climate changes. Mediangrain-size along the 253.1 m sequence varies from 6 to 13 μm and the 】 63 μm fraction representsonly 5.3% in maximum, 0.9% in average. Long-term grain-size variations are consistent with the loessaccumulation rate at Qinan and with the eolian mass accumulation rate in the North Pacific. Thesefeatures firmly indicate an eolian origin of the studied sequence, and also reveal a coeval changesbetween the long-term changes of eolian grain-size and continental aridity in the dust sourceregions.