Positioning of screw holes is an important production procedure for steel construction connecting with bolts. In this paper, a new production method is presented, in which the digital camera is used for taking picture...Positioning of screw holes is an important production procedure for steel construction connecting with bolts. In this paper, a new production method is presented, in which the digital camera is used for taking pictures of screw holes and other techniques are advanced. This paper also indicates that the pixels of CCD chip in photogrammetry should be chosen as all geometric units in an image, such as interior elements and all kinds of distortions. The measure can also simplify the camera calibration for determining the size of non-square pixel.展开更多
This paper reports the results of the aerodynamic deformation measurements of the meter-scale, entire shape, actual UAV in the wind tunnel using a video grammetry technique. The measured airplane was the airplane for ...This paper reports the results of the aerodynamic deformation measurements of the meter-scale, entire shape, actual UAV in the wind tunnel using a video grammetry technique. The measured airplane was the airplane for Mars exploration being developed by Japan Aerospace Exploration Agency (JAXA) and Japanese universities. Its main wing span length was 2.4 m. The video grammetry measurement was performed using VICON’s system. Retroactive markers and stickers were put on the airplane. JAXA’s 6.5 m × 5.5 m Low-Speed Wind Tunnel was used. The airplane was mounted on the strut support with pitch-free or pitch-locked conditions. The deformations of the main wing bending, the main wing twisting, the tail boom bending, and the elevator deflection angle change were revealed quantitatively. The bending stiffness of a main wing spar that was designed as a safety factor of 2.8 at load factor of 5 was sufficient. The main wing spar was located around a center of pressure of an airfoil and it showed enough stiffness for twisting at nominal condition. The effects of the main wing bending and twisting, and the tail boom bending on the aerodynamic performance were estimated but they were in an acceptable range from the standpoint of the controllability of the aerodynamic performance using control surfaces. Even though the servo motor was located near the elevator and the linkage between the servo motor and the elevator was short, the measured elevator deflection angle was at most 4% smaller than the angle at no-wind condition. The obtained results and presented method are useful for control, flight data analysis, and design of lightweight airplanes.展开更多
文摘Positioning of screw holes is an important production procedure for steel construction connecting with bolts. In this paper, a new production method is presented, in which the digital camera is used for taking pictures of screw holes and other techniques are advanced. This paper also indicates that the pixels of CCD chip in photogrammetry should be chosen as all geometric units in an image, such as interior elements and all kinds of distortions. The measure can also simplify the camera calibration for determining the size of non-square pixel.
文摘This paper reports the results of the aerodynamic deformation measurements of the meter-scale, entire shape, actual UAV in the wind tunnel using a video grammetry technique. The measured airplane was the airplane for Mars exploration being developed by Japan Aerospace Exploration Agency (JAXA) and Japanese universities. Its main wing span length was 2.4 m. The video grammetry measurement was performed using VICON’s system. Retroactive markers and stickers were put on the airplane. JAXA’s 6.5 m × 5.5 m Low-Speed Wind Tunnel was used. The airplane was mounted on the strut support with pitch-free or pitch-locked conditions. The deformations of the main wing bending, the main wing twisting, the tail boom bending, and the elevator deflection angle change were revealed quantitatively. The bending stiffness of a main wing spar that was designed as a safety factor of 2.8 at load factor of 5 was sufficient. The main wing spar was located around a center of pressure of an airfoil and it showed enough stiffness for twisting at nominal condition. The effects of the main wing bending and twisting, and the tail boom bending on the aerodynamic performance were estimated but they were in an acceptable range from the standpoint of the controllability of the aerodynamic performance using control surfaces. Even though the servo motor was located near the elevator and the linkage between the servo motor and the elevator was short, the measured elevator deflection angle was at most 4% smaller than the angle at no-wind condition. The obtained results and presented method are useful for control, flight data analysis, and design of lightweight airplanes.
