The Results of Research to Determine the Parameters of HardeningWorking Area of the Gin and Linter Grates

The article provides substantiation of the choice of the quenching parametersfor the working zone of gin and linter grates and the quenchingparameters.The results of bench and industrial tests of the grate with ahardened working zone are also given.

Thermo-hydro-poro-mechanical responses of a reservoir-induced landslide tracked by high-resolution fiber optic sensing nerves

Thermo-poro-mechanical responses along sliding zone/surface have been extensively studied.However,it has not been recognized that the potential contribution of other crucial engineering geological interfaces beyond the slip surface to progressive failure.Here,we aim to investigate the subsurface multiphysics of reservoir landslides under two extreme hydrologic conditions(i.e.wet and dry),particularly within sliding masses.Based on ultra-weak fiber Bragg grating(UWFBG)technology,we employ specialpurpose fiber optic sensing cables that can be implanted into boreholes as“nerves of the Earth”to collect data on soil temperature,water content,pore water pressure,and strain.The Xinpu landslide in the middle reach of the Three Gorges Reservoir Area in China was selected as a case study to establish a paradigm for in situ thermo-hydro-poro-mechanical monitoring.These UWFBG-based sensing cables were vertically buried in a 31 m-deep borehole at the foot of the landslide,with a resolution of 1 m except for the pressure sensor.We reported field measurements covering the period 2021 and 2022 and produced the spatiotemporal profiles throughout the borehole.Results show that wet years are more likely to motivate landslide motions than dry years.The annual thermally active layer of the landslide has a critical depth of roughly 9 m and might move downward in warmer years.The dynamic groundwater table is located at depths of 9e15 m,where the peaked strain undergoes a periodical response of leap and withdrawal to annual hydrometeorological cycles.These interface behaviors may support the interpretation of the contribution of reservoir regulation to slope stability,allowing us to correlate them to local damage events and potential global destabilization.This paper also offers a natural framework for interpreting thermo-hydro-poro-mechanical signatures from creeping reservoir bank slopes,which may form the basis for a landslide monitoring and early warning system.

Compact magneto-optical traps using planar optics

Magneto-optical traps (MOTs) composed of magnetic fields and light fields have been widely utilized to cool andconfine microscopic particles. Practical technology applications require miniaturized MOTs. The advancement of planaroptics has promoted the development of compact MOTs. In this article, we review the development of compact MOTs basedon planar optics. First, we introduce the standardMOTs. We then introduce the gratingMOTs with micron structures, whichhave been used to build cold atomic clocks, cold atomic interferometers, and ultra-cold sources. Further, we introducethe integrated MOTs based on nano-scale metasurfaces. These new compact MOTs greatly reduce volume and powerconsumption, and provide new opportunities for fundamental research and practical applications.

Industrial utilization of arsenic-containing gold dressing tailings as pellet prepared by straight grate process

The utilization of arsenic-containing gold dressing tailings is an urgent issue faced by gold production companies worldwide.The thermodynamic analysis results indicate that ferrous arsenate(FeAsO_(4)),pyrite(FeS_(2))and sodium cyanide(NaCN)in the arsenic-containing gold metallurgical tailings can be effectively removed using straight grate process,and the removal of pyrite and sodium cyanide is basically completed during the preheating stage,while the removal of ferrous arsenate requires the roasting stage.The pellets undergo a transformation from magnetite to hematite during the preheating process,and are solidified through micro-crystalline bonding and high-temperature recrystallization of hematite(Fe_(2)O_(3))during the roasting process.Ultimately,pellets with removal rates of 80.77% for arsenic,88.78% for sulfur,and 99.88% for cyanide are obtained,as well as the iron content is 61.1% and the compressive strength is 3071 N,meeting the requirements for blast furnace burden.This study provides an industrially feasible method for treating arsenic-containing gold smelting tailings,benefiting gold production enterprises.

Model-driven CT reconstruction algorithm for nano-resolution x-ray phase contrast imaging

The low-density imaging performance of a zone plate-based nano-resolution hard x-ray computed tomography(CT)system can be significantly improved by incorporating a grating-based Lau interferometer. Due to the diffraction, however,the acquired nano-resolution phase signal may suffer splitting problem, which impedes the direct reconstruction of phase contrast CT(nPCT) images. To overcome, a new model-driven nPCT image reconstruction algorithm is developed in this study. In it, the diffraction procedure is mathematically modeled into a matrix B, from which the projections without signal splitting can be generated invertedly. Furthermore, a penalized weighted least-square model with total variation(PWLSTV) is employed to denoise these projections, from which nPCT images with high accuracy are directly reconstructed.Numerical experiments demonstrate that this new algorithm is able to work with phase projections having any splitting distances. Moreover, results also reveal that nPCT images of higher signal-to-noise-ratio(SNR) could be reconstructed from projections having larger splitting distances. In summary, a novel model-driven nPCT image reconstruction algorithm with high accuracy and robustness is verified for the Lau interferometer-based hard x-ray nano-resolution phase contrast imaging.

Theory and verification of moiréfringes for x-ray three-phase grating interferometer

Dual-phase and three-phase grating x-ray interference is a promising new technique for grating-based x-ray differential phase contrast imaging.Dual-phase grating interferometers have been relatively completely studied and discussed.In this paper,the corresponding imaging fringe formula of the three-phase grating interferometer is provided.At the same time,the similarities and differences between the three-phase grating interferometer and the dual-phase grating interferometer are investigated and verified,and that the three-phase grating interferometer can produce large-period moiréfringes without using the analyzing grating is demonstrated experimentally.Finally,a simple method of designing three-phase grating and multi-grating imaging systems from geometric optics based on the thin-lens theory of gratings is presented.These theoretical formulas and experimental results provide optimization tools for designing three-phase grating interferometer systems.

Model of self-generated magnetic field generation from relativistic laser interaction with solid targets

Generation of self-generated annular magnetic fields at the rear side of a solid target driven by relativistic laser pulse is investigated by using theoretical analysis and particle-in-cell simulations.The spatial strength distribution of magnetic fields can be accurately predicted by calculating the net flow caused by the superposition of source flow and return flow of hot electrons.The theoretical model established shows good agreement with the simulation results,indicating that the magnetic-field strength scales positively to the temperature of hot electrons.This provides us a way to improve the magnetic-field generation by using a micro-structured plasma grating in front of the solid target.Compared with that for a common flat target,hot electrons can be effectively heated with the well-designed grating size,leading to a stronger magnetic field.The spatial distribution of magnetic fields can be modulated by optimizing the grating period and height as well as the incident angle of the laser pulse.

975 nm multimode semiconductor lasers with high-order Bragg diffraction gratings

The 975 nm multimode diode lasers with high-order surface Bragg diffraction gratings have been simulated and calcu-lated using the 2D finite difference time domain(FDTD)algorithm and the scattering matrix method(SMM).The periods and etch depth of the grating parameters have been optimized.A board area laser diode(BA-LD)with high-order diffraction grat-ings has been designed and fabricated.At output powers up to 10.5 W,the measured spectral width of full width at half maxi-mum(FWHM)is less than 0.5 nm.The results demonstrate that the designed high-order surface gratings can effectively nar-row the spectral width of multimode semiconductor lasers at high output power.

Enhancing the Goos-Hänchen shift based on quasi-bound states in the continuum through material asymmetric dielectric compound gratings

Quasi-bound state in the continuum(QBIC)resonance is gradually attracting attention and being applied in Goos-Hänchen(GH)shift enhancement due to its high quality(Q)factor and superior optical confinement.Currently,symmetry-protected QBIC resonance is often achieved by breaking the geometric symmetry,but few cases are achieved by breaking the material symmetry.This paper proposes a dielectric compound grating to achieve a high Q factor and high-reflection symmetry-protectede QBIC resonance based on material asymmetry.Theoretical calculations show that the symmetry-protected QBIC resonance achieved by material asymmetry can significantly increase the GH shift up to-980 times the resonance wavelength,and the maximum GH shift is located at the reflection peak with unity reflectance.This paper provides a theoretical basis for designing and fabricating high-performance GH shift tunable metasurfaces/dielectric gratings in the future.

Monitoring shear deformation of sliding zone via fiber Bragg grating and particle image velocimetry

Monitoring shear deformation of sliding zones is of great significance for understanding the landslide evolution mechanism,in which fiber optic strain sensing has shown great potential.However,the cor-relation between strain measurements of quasi-distributed fiber Bragg grating(FBG)sensing arrays and shear displacements of surrounding soil remains elusive.In this study,a direct shear model test was conducted to simulate the shear deformation of sliding zones,in which the soil internal deformation was captured using FBG strain sensors and the soil surface deformation was measured by particle image velocimetry(PIV).The test results show that there were two main slip surfaces and two secondary ones,developing a spindle-shaped shear band in the soil.The formation of the shear band was successfully captured by FBG sensors.A sinusoidal model was proposed to describe the fiber optic cable deformation behavior.On this basis,the shear displacements and shear band widths were calculated by using strain measurements.This work provides important insight into the deduction of soil shear deformation using soil-embedded FBG strain sensors.

End-to-end computational design for an EUV solar corona multispectral imager with stray light suppression

An extreme ultraviolet solar corona multispectral imager can allow direct observation of high temperature coronal plasma,which is related to solar flares,coronal mass ejections and other significant coronal activities.This manuscript proposes a novel end-to-end computational design method for an extreme ultraviolet(EUV)solar corona multispectral imager operating at wavelengths near 100 nm,including a stray light suppression design and computational image recovery.To suppress the strong stray light from the solar disk,an outer opto-mechanical structure is designed to protect the imaging component of the system.Considering the low reflectivity(less than 70%)and strong-scattering(roughness)of existing extreme ultraviolet optical elements,the imaging component comprises only a primary mirror and a curved grating.A Lyot aperture is used to further suppress any residual stray light.Finally,a deep learning computational imaging method is used to correct the individual multi-wavelength images from the original recorded multi-slit data.In results and data,this can achieve a far-field angular resolution below 7",and spectral resolution below 0.05 nm.The field of view is±3 R_(☉)along the multi-slit moving direction,where R☉represents the radius of the solar disk.The ratio of the corona's stray light intensity to the solar center's irradiation intensity is less than 10-6 at the circle of 1.3 R_(☉).

FBG技术监测分析机场跑道沥青加铺层反射裂缝扩展过程

反射裂缝是导致机场跑道加铺层失效的主要病害之一。为分析机场水泥跑道沥青加铺层反射裂缝扩展过程,本文基于光纤布拉格光栅(FBG,fiber Bragg grating)传感技术,提出了可用于实时监测机场水泥跑道沥青加铺层反射裂缝扩展过程的柔性FBG传感器封装方法,并对研发的FBG传感器进行了标定。基于室内组合梁试验,分析了机场水泥跑道沥青加铺层复合结构反射裂缝扩展过程,包括微裂纹萌生与积累、反射裂缝扩展、反射裂缝贯通3个阶段。在反射裂缝扩展初期,FBG传感器中心波长增长速率相对较小;随着反射裂缝逐渐扩展,FBG传感器中心波长迅速增大。结果表明,柔性FBG传感器全部存活且性能完整,验证了其在实时监测机场水泥跑道沥青加铺层反射裂缝扩展过程中的可行性。

Waveguide Bragg Grating for Fault Localization in PON

Femtosecond laser direct inscription is a technique especially useful for prototyping purposes due to its distinctive advantages such as high fabrication accuracy,true 3D processing flexibility,and no need for mold or photomask.In this paper,we demonstrate the design and fabrication of a planar lightwave circuit(PLC)power splitter encoded with waveguide Bragg gratings(WBG)using a femtosecond laser inscription technique for passive optical network(PON)fault localization application.Both the reflected wavelengths and intervals of WBGs can be conveniently tuned.In the experiment,we succeeded in directly inscribing WBGs in 1×4 PLC splitter chips with a wavelength interval of about 4 nm and an adjustable reflectivity of up to 70% in the C-band.The proposed method is suitable for the prototyping of a PLC splitter encoded with WBG for PON fault localization applications.

Magnetic filtration of an iron oxide aerosol by means of magnetizable grates

The cleaning of gases with low concentrations of small ferromagnetic or paramagnetic particles is a difficult task for conventional filtration. A new alternative procedure, magnetic filtration, is used in this work. Iron oxide aerosol was generated by elutriation of iron oxide particles from a fluidized bed consisting of a mixture of Geldart-C iron oxide powder and large spherical Geldart-B sand particles. The aerosol was filtered by means of a magnetic filter which consisted of one, two or three iron grates staggered to each other. The experimental installation contained also an isokinetic sampling system and a Microtrac SRA 150 Particle Analyser. A theoretical expression for filtration efficiency was deduced from a previous model taking into account the different forces acting on the iron oxide particles. Experimental filtration efficiency matches quite well calculated theoretical efficiency. It was found that an increase in particle size, in thee number of grates or in the applied magnetic field produced higher filtration efficiencies up to 100% in some cases. In all filtration experiments pressure drop through the magnetic filter was very small.

Strain-Insensitive Fiber Bragg Grating Composite Structure for Wide-Range Temperature Sensing

This paper reports on the design,fabrication,and temperature strain sensing performance of a fiber Bragg grating composite structure for surface mounted temperature measurements over a wide temperature range,with highly reduced strain cross-sensitivity.The fiber Bragg grating sensor is encapsulated in a polyimide tube filled with epoxy resin,forming an arc-shaped cavity.This assembly is then placed between two layers of glass fiber prepreg with a flexible pad in between and cured into shape.Experimental results,supported by finite element simulations,demonstrate an enhanced temperature sensitivity is 26.3 pm/°C over a wide temperature range of–30°C to 70°C,and high strain transfer isolation of about 99.65%.

基于FBG-3D打印的土工格栅加筋下伏土洞路基模型试验

光纤布拉格光栅(fiber Bragg grating,FBG)传感技术具有高灵敏度、抗电磁干扰和实时监测等优点,在土木工程领域越来越受到关注,但传统的外部封装方式难以实现传感器与被测物体的完全协调变形,易导致测量误差.基于3D打印技术研发了一种自感知土工格栅,实现了光纤光栅传感器与被测土工格栅的完全协调变形,利用FBG传感技术直接实现对格栅应变的实时、准确测量.并且,将该自感知土工格栅应用于下伏土洞路基的模型试验中,研究在不同加筋层数和加筋间距下路基的极限承载力、顶端沉降及筋材的变形特性.试验结果表明,通过加筋可以大幅提高下伏土洞路基的极限承载力,并可有效减少路基破坏时的沉降;加筋层数的增加和加筋间距的减小均可以提高下伏土洞路基承载力;在垂直方向上,格栅的应变随着格栅的埋深增大而减小;在水平方向上,格栅的应变随着与加载中心之间的距离增大而向两侧递减;顶层格栅的应变随着加筋层数的增加而减小,随着加筋间距的减小而增大.试验结果验证了自感知土工格栅在下伏土洞加筋路基监测中应用的可行性.

Spatiotemporal hemodynamic monitoring via configurable skin-like microfiber Bragg grating group

Systemic blood circulation is one of life activity’s most important physiological functions.Continuous noninvasive hemodynamicmonitoring is essential for the management of cardiovascular status.However,it is difficult to achieve systemichemodynamic monitoring with the daily use of current devices due to the lack of multichannel and time-synchronized operationcapability over the whole body.Here,we utilize a soft microfiber Bragg grating group to monitor spatiotemporalhemodynamics by taking advantage of the high sensitivity,electromagnetic immunity,and great temporal synchronizationbetween multiple remote sensor nodes.A continuous systemic hemodynamic measurement technique is developedusing all-mechanical physiological signals,such as ballistocardiogram signals and pulse waves,to illustrate the actualmechanical process of blood circulation.Multiple hemodynamic parameters,such as systemic pulse transit time,heartrate,blood pressure,and peripheral resistance,are monitored using skin-like microfiber Bragg grating patches conformallyattached at different body locations.Relying on the soft microfiber Bragg grating group,the spatiotemporal hemodynamicmonitoring technique opens up new possibilities in clinical medical diagnosis and daily health management.

In-fiber photoelectric device based on graphene-coated tilted fiber grating

Graphene and related two-dimensional materials have attracted great research interests due to prominently optical and electrical properties and flexibility in integration with versatile photonic structures.Here,we report an in-fiber photoelec-tric device by wrapping a few-layer graphene and bonding a pair of electrodes onto a tilted fiber Bragg grating(TFBG)for photoelectric and electric-induced thermo-optic conversions.The transmitted spectrum from this device consists of a dense comb of narrowband resonances that provides an observable window to sense the photocurrent and the electrical injection in the graphene layer.The device has a wavelength-sensitive photoresponse with responsivity up to 11.4 A/W,allowing the spectrum analysis by real-time monitoring of photocurrent evolution.Based on the thermal-optic effect of electrical injection,the graphene layer is energized to produce a global red-shift of the transmission spectrum of the TF-BG,with a high sensitivity approaching 2.167×10^(4)nm/A^(2).The in-fiber photoelectric device,therefore as a powerful tool,could be widely available as off-the-shelf product for photodetection,spectrometer and current sensor.

Anti-symmetric sampled grating quantum cascade laser for mode selection

For mode selection in a quantum cascade laser(QCL),we demonstrate an anti-symmetric sampled grating(ASG).The wavelength of the-1-th mode of this laser has been blue-shifted more than 75 nm(~10 cm^(-1))compared with that of an ordinary sampled grating laser with an emission wavelength of approximately 8.6μm,when the periodicities within both the base grating and the sample grating are kept constant.Under this condition,an improvement in the continuous tuning capability of the QCL array is ensured.The ASG structure is fabricated in holographic exposure and optical photolithography,thereby enhancing its flexibility,repeatability,and cost-effectiveness.The wavelength modulation capability of the two channels of the grating is insensitive to the variations in channel size,assuming that the overall waveguide width remains constant.The output wavelength can be tailored freely within a certain range by adjusting the width of the ridge and the material of the cladding layer.

Novel Apodized Fiber Bragg GratingApplied for Medical Sensors:Performance Investigation

Sensors play an important role in shaping and monitoring human health.Exploration of methods to use Fiber Bragg Grating(FBG)with enhanced sensitivity has attracted great interest in the field of medical research.In this paper,a novel apodization function is proposed and performance evaluation and optimization of the same have been made.A comparison was conducted between various existing apodization functions and the proposed one based on optical characteristics and sensor parameters.The results evince the implementation of the proposed apodization function for vital sign measurement.The optical characteristics considered for evaluation are Peak Resonance Reflectivity level,Side Lobes Reflectivity level and FullWidth HalfMaximum(FWHM).The proposed novel apodization novel function has better FWHM,which is narrower than the FWHM of uniform FBG.Sensor characteristics like a quality parameter,detection accuracy and sensitivity also show improvement.The proposed novel apodization function is demonstrated to have a better shift in wavelength in terms of temperature and pulse measurement than the existing functions.The sensitivity of the proposed apodized function is enhanced with a Poly-dimethylsiloxane coating of varying thickness,which is 6 times and 5.14 times greater than uniform Fiber Bragg grating and FBG with the proposed novel apodization function,respectively,enhancing its utilization in the field of medicine.