Micron-sized fiber diamond probe for quantum precision measurement of microwave magnetic field

We present a quantitative measurement of the horizontal component of the microwave magnetic field of a coplanar waveguide using a quantum diamond probe in fiber format.The measurement results are compared in detail with simulation,showing a good consistence.Further simulation shows fiber diamond probe brings negligible disturbance to the field under measurement compared to bulk diamond.This method will find important applications ranging from electromagnetic compatibility test and failure analysis of high frequency and high complexity integrated circuits.

Precision measurement and suppression of low-frequency noise in a current source with double-resonance alignment magnetometers

Low-noise high-stability current sources have essential applications such as neutron electric dipole moment measurement and high-stability magnetometers. Previous studies mainly focused on frequency noise above 0.1 Hz while less on the low-frequency noise/drift. We use double resonance alignment magnetometers(DRAMs) to measure and suppress the low-frequency noise of a homemade current source(CS) board. The CS board noise level is suppressed by about 10 times in the range of 0.001-0.1 Hz and is reduced to 100 n A/√Hz at 0.001 Hz. The relative stability of CS board can reach2.2 × 10^(-8). In addition, the DRAM shows a better resolution and accuracy than a commercial 7.5-digit multimeter when measuring our homemade CS board. Further, by combining the DRAM with a double resonance orientation magnetometer,we may realize a low-noise CS in the 0.001-1000 Hz range.

Quantum-enhanced optical precision measurement assisted by low-frequency squeezed vacuum states

Stable low-frequency squeezed vacuum states at a wavelength of 1550 nm were generated.By controlling the squeezing angle of the squeezed vacuum states,two types of low-frequency quadrature-phase squeezed vacuum states and quadrature-amplitude squeezed vacuum states were obtained using one setup respectively.A quantum-enhanced fiber Mach–Zehnder interferometer(FMZI)was demonstrated for low-frequency phase measurement using the generated quadrature-phase squeezed vacuum states that were injected.When phase modulation was measured with the quantumenhanced FMZI,there were above 3 dB quantum improvements beyond the shot-noise limit(SNL)from 40 kHz to 200 kHz,and 2.3 dB quantum improvement beyond the SNL at 20 kHz was obtained.The generated quadrature-amplitude squeezed vacuum state was applied to perform low-frequency amplitude modulation measurement for sensitivity beyond the SNL based on optical fiber construction.There were about 2 dB quantum improvements beyond the SNL from 60 kHz to 200 kHz.The current scheme proves that quantum-enhanced fiber-based sensors are feasible and have potential applications in high-precision measurements based on fiber,particularly in the low-frequency range.

TIME-SPACE CONCEPT FOR PRECISION MEASUREMENT

The transformation between time and space is discussed. To improve real-time response speed of intelligent measuring system, the concept of exchanging program execution time with more circuitry is presented working in cycle mode. Displacement measuring by magnification is achieved with period measurement by magnification. To change the condition that traditional precision measurement depends on machining precision greatly, the concept of measuring space with time and theory of time-space coordinate transformation are proposed. Guided by the idea of measuring space with time, differential frequency measurement system and time grating displacement sensor are developed based on the proposed novel methods. And high-precision measurement is achieved without high-precision manufacture, which embeds the remarkable characteristics of low cost but high precision to the devices. Experiment and test results conform the validity of the proposed time-space concept.

Precision measurements with cold atoms and trapped ions

Recent progresses on quantum control of cold atoms and trapped ions in both the scientific and technological aspects greatly advance the applications in precision measurement. Thanks to the exceptional controllability and versatility of these massive quantum systems, unprecedented sensitivity has been achieved in clocks, magnetometers, and interferometers based on cold atoms and ions. Besides, these systems also feature many characteristics that can be employed to facilitate the applications in different scenarios. In this review, we briefly introduce the principles of optical clocks, cold atom magnetometers, and atom interferometers used for precision measurement of time, magnetic field, and inertial forces. The main content is then devoted to summarize some recent experimental and theoretical progresses in these three applications, with special attention being paid to the new designs and possibilities towards better performance. The purpose of this review is by no means to give a complete overview of all important works in this fast developing field, but to draw a rough sketch about the frontiers and show the fascinating future lying ahead.

High-Precision Wideband Phase-Derived Velocity Measurement for Micro-Motion Extraction

A phase-derived velocity measurement method is proposed in a wideband coherent system,based on a precise echo model considering the inner pulse Doppler effect caused by fast moving targets.The Cramer-Rao low band of velocity measurement precision is deduced,demonstrating the high precision of the proposed method.Simulations and out-field experiments further validate the effectiveness of the proposed method in high-precision measurement and micro-motion extraction for targets with weak reflection intensity.Compared with the long-time integration approaches for velocity measurement,the phase-derived method is easy to implement and meets the requirement for high data rate,which makes it suitable for micro-motion feature extraction in wideband systems.

Precision measurement with atom interferometry

Development of atom interferometry and its application in precision measurement are reviewed in this paper. The principle, features and the implementation of atom interferometers are introduced, the recent progress of precision measurement with atom interferometry, including determination of gravitational constant and fine structure constant, measurement of gravity, gravity gradient and rotation, test of weak equivalence principle, proposal of gravitational wave detection, and measurement of quadratic Zeeman shift are reviewed in detail. Determination of gravitational redshift, new definition of kilogram, and measurement of weak force with atom interferometry are also briefly introduced.

A new high-precision gravity solid tidal model for Precision Gravity Measurement Facility

It is significant for establishing gravity datum to construct precise gravity solid tidal model,A simple method with relatively low performance is to interpolate tidal parameters from the global gravity solid tide models.A competitive approach is to determine local gravity solid tidal model by harmonic analysis using long-time serial gravity observations.In this paper a new high-precision gravity solid tidal model for Precision Gravity Measurement Facility is estimated from two co-site gravimeters in the cave laboratory using modern international standard data processing techniques,whose accuracy is evaluated further by comparing with previous publications.The results show that:(1)the determined gravity solid tidal models from two co-site gravimeters are in good agreement with each other,of which the maximum differences for amplitude factors and phase delays don’t exceed 0.01700%and 2.50990°,respectively.(2)the performance of the obtained gravity solid tidal model is 0.00411 for amplitude factors and 0.24120°for phase delays,which is a little better than that of previous publications using superconducting gravity data from Wuhan station.(3)our results and methods are corrective and effective.(4)our model is tiny different from that provided by Wuhan station,which implies that it is necessary to construct a gravity solid tidal model for Precision Gravity Measurement Facility,rather than just adopting existing models at Wuhan station.Our results are helpful in realizing the goal of Precision Gravity Measurement Facility.

Experimental Measurements of the Sensitivity of Fiber-optic Bragg Grating Sensors with a Soft Polymeric Coating under Mechanical Loading,Thermal and Magnetic under Cryogenic Conditions

The strain and temperature sensing performance of fiber-optic Bragg gratings （FBGs） with soft polymeric coating, which can be used to sense internal strain in superconducting coils, are evaluated under variable cryogenic field and magnetic field. The response to a temperature and strain change of coated-soft polymeric FBGs is tested by comparing with those of coated-metal FBGs. The results indicate that the coated-soft polymeric FBGs can freely detect temperature and thermal strain, their At variable magnetic field, the tested results indicate accuracy and repeatability are also discussed in detail. that the cross-coupling effects of FBGs with different matrixes are not negligible to measure electromagnetic strain during fast excitation. The present results are expected to be able to provide basis measurements on the strain of pulsed superconducting magnet/cable （cable- around-conduit conductors, cable-in-conduit conductors）, independently or utilized together with other strain measurement methods.

A Study of Precision Factors of Large-scale Object Surface Profile Laser Scanning Measurement

In this paper, we presented a method of using the l as er scanning triangulation for the non-contact 3D surface profile measurement of large-scale object. The characteristic of large-scale object non-contact mea surement is analyzed and the measuring method is proposed. Main factors influenc ing measurement precision such as image distortion and accurate designation of s peckle center are analyzed and methods of solving these problems are proposed. W e designed a combined filter by which the pulse noise and the Gaussian noise of speckle image can be eliminated efficiently. Using the characteristic of intensi ty distribution of laser speckle image we proposed a new approximating method th at could locate the center of laser speckle image at sub-pixel. The auxiliary v ariables are set to linearize the relationship between the image displacement an d the distance, the accurate values of laser triangulation system parameters cou ld be calibrated accurately and the measuring precision is increased remarkabl y. Using the above techniques we designed a measuring system based on laser sc anning triangulation. The results of the experiment show that these methods can raise the measuring precision of large-scale 3D surface profile effectively.

Measurement of a discontinuous object based on a dual-frequency grating

The dual-frequency grating measurement theory is proposed in order to carry out the measurement of a discontinuous object. Firstly, the reason why frequency spectra are produced by low frequency gratings and high frequency gratings in the field of frequency is analysed, and the relationship between the wrapped-phase and the unwrapping-phase is discussed. Secondly, a method to combine the advantages of the two kinds of gratings is proposed： one stripe is produced in the mutation part of the object measured by a suitable low frequency grating designed by MATLAB, then the phase produced by the low frequency grating need not be unfolded. The integer series of stripes is produced by a high frequency grating designed by MATLAB based on the frequency ratio of the two kinds of gratings and the high frequency wrapped-phase, and the high frequency unwrapping-phase is then obtained. In order to verify the correctness of the theoretical analysis, a steep discontinuous object of 600×600 pixels and 10.00 mm in height is simulated and a discontinuous object of ladder shape which is 32.00 mm in height is used in experiment. Both the simulation and the experiment can restore the discontinuous object height accurately by using the dual-frequency grating measurement theory.

Enhancing the precision of phase estimation by weak measurement and quantum measurement reversal

The enhancement of the precision of phase estimation in quantum metrology is investigated by employing weak measurement （WM） and quantum measurement reversal （QMR）. We derive the exact expressions of the optimal quantum Fisher information （QFI） and success probability of phase estimation for an exactly solving model consisting of a qubit interacting with a structured reservoir. We show that the QFI can be obviously enhanced by means of the WM and QMR in different regimes. In addition, we also show that the magnitude of the decoherence involved in the WM and QMR can be a general complex number, which extends the applicable scope of the WM and QMR approach.

Multi-parameter identification of gratings measurement by Experimental Ray Tracing

A simple method for measuring grating groove density as well as its position and orientation is proposed based on the idea of ERT(Experimental Ray Tracing).Conventional methods only measure grating groove density with accuracy limited by its rotary stage and goniometer.The method proposed in the paper utilizes linear guides which could be calibrated to much higher accuracy.It is applicable to gratings of arbitrary surface profile or mosaic of a group of various gratings.Various measurement error sources are simulated by the Monte Carlo method and the results show high accuracy capability of grating parameters identification.A verification testing is performed.The accuracy dependency on main configuration parameters is evaluated.A method to expand measurement range by double wavelength is also discussed.

Effect Factors on Measurement Precision of the Embedded Temperature Sensing Fabric

The embedded temperature sensing fabric was designed and woven according to the heat transmission model of the fabric.The temperature sensors were embedded into the multi-layered fabric that weft yarns were high-shrinkage polyester filaments.And the fabric was treated by a self-designed partial heat device,which can make the sensor be fixed in the fabric.The effects of yarn type,yarn linear density,fabric warp density,fabric structure,fabric layer numbers where the sensor is located,and the ambient temperature on the temperature measured value were investigated.The results demonstrated that when the higher thermal conductivity of yarns and lower density yarns were applied in the fabric as rawmaterials,they were favored to improve the measurement precision.Meanwhile,there were many factors that could make the measured values closer to the real value of the body,such as the plain fabric,the increased warp density of the fabric,the multiple-layer fabric where the sensor was located,the raised ambient testing temperature and the prolonged test time in the certain range.

Preliminary Application of Combinatorial Measurement and Regression Analysis Method to High Precision Instrumental Analysis

With determination micro-Fe by 1, 10-phenanthroline spectrophotometry for example, they are systematically introduced the combinatorial measurement and regression analysis method application about metheodic principle, operation step and data processing in the instrumental analysis, including: calibration curve best linear equation is set up, measurand best linear equation is set up, and calculation of best value of a concentration. The results showed that mean of thrice determination , s = 0 μg/mL, RSD = 0. Results of preliminary application are simply introduced in the basic instrumental analysis for atomic absorption spectrophotometry, ion-selective electrodes, coulometry and polarographic analysis and are contrasted to results of normal measurements.

High Precision Tungsten Isotope Measurements by MC-ICPMS

1 Introduction The short-lived 182Hf-182W system is generally acknowledged as the best chronometer of metal-silicate segregation that occurred during the early evolution of asteroids and terrestrial planets due to its following properties:(1)Hf-W fractionation commonly occurs during metal-silicate differentiation;(2)Both Hf and W are highly refractory elements,therefore most bulk

A Fast Small-Sample Modeling Method for Precision Inertial Systems Fault Prediction and Quantitative Anomaly Measurement

Inertial system platforms are a kind of important precision devices,which have the characteristics of difficult acquisition for state data and small sample scale.Focusing on the model optimization for data-driven fault state prediction and quantitative degreemeasurement,a fast small-sample supersphere one-class SVMmodelingmethod using support vectors pre-selection is systematically studied in this paper.By theorem-proving the irrelevance between themodel’s learning result and the non-support vectors(NSVs),the distribution characters of the support vectors are analyzed.On this basis,a modeling method with selected samples having specific geometry character fromthe training sets is also proposed.The method can remarkably eliminate theNSVs and improve the algorithm’s efficiency.The experimental results testify that the scale of training samples and the modeling time consumption both give a sharply decrease using the support vectors pre-selection method.The experimental results on inertial devices also show good fault prediction capability and effectiveness of quantitative anomaly measurement.

Using chaos to improve measurement precision

If the measuring signals were input to the chaotic dynamic system as initial parameters, the system outputs might be in steady state, periodic state or chaos state. If the chaotic dynamic system outputs controlled in the periodic states, the periodic numbers would be changed most with the signals. Our novel method is to add chaotic dynamic vibration to the measurement or sensor system.The sensor sensitivity and precision of a measurement system would be improved with this method. Chaotic dynamics measurement algorithms are given and their sensitivity to parameters are analyzed in this paper. The effects of noises on the system are discussed.

Precision Frequency Measurement of ^(87)Rb 5S_(1/2)(F=2)→5D_(5/2)(F″=4)Two-Photon Transition through a Fiber-Based Optical Frequency Comb

The absolute frequency of 87Rb 5S1/2 （F=2）→5D5/2 （F＂ = 4） two-photon transition at 778nm is measured in an accuracy of 44kHz. A home-made erbium-doped fiber laser frequency comb with frequency stability of 5.0 × 10-13@1 s is employed for the light source. By using a periodically poled lithium niobate, the femtosecond pulse operating in 1556 nm is frequency-doubled to 778 nm to obtain the direct two-photon transition spectroscopy of thermal rubidium vapor. Through sweeping the carrier envelope offset frequency （fceo）, the 5S1/2 （F=2）→5D5/2 （F＂ = 4） two-photon transition line is clearly resolved and its absolute frequency is determined via the peak-finding of the fitting curve. After the frequency correction, the measured result agrees well with the previous experiment on this transition. The entire potential candidate of optical frequency standard for system configuration is compact and robust, providing a telecommunication applications.

Hybrid Long-Period Fiber Grating with Multimode Fiber Core for Refractive Index Measurement

A refractive index （RI） sensor based on hybrid long-period fiber grating （LPFG） with multimode fiber core （MMFC） is proposed and demonstrated. The surrounding RI can be determined by monitoring the separation between the resonant wavelengths of the LPFG and MMFC since the resonant wavelengths of the LPFG and MMFC will shift in opposite directions when the surrounding RI changes. Experimental results show that the sensor possesses an enhanced sensitivity of 526.92nm/RIU in the RI range of 1.387-1.394 RIU. The response to the temperature is also discussed.