Variational Mode Decomposition-Informed Empirical Wavelet Transform for Electric Vibrator Noise Analysis

Electric vibrators find wide applications in reliability testing, waveform generation, and vibration simulation, making their noise characteristics a topic of significant interest. While Variational Mode Decomposition (VMD) and Empirical Wavelet Transform (EWT) offer valuable support for studying signal components, they also present certain limitations. This article integrates the strengths of both methods and proposes an enhanced approach that integrates VMD into the frequency band division principle of EWT. Initially, the method decomposes the signal using VMD, determining the mode count based on residuals, and subsequently employs EWT decomposition based on this information. This addresses mode aliasing issues in the original method while capitalizing on VMD’s adaptability. Feasibility was confirmed through simulation signals and ultimately applied to noise signals from vibrators. Experimental results demonstrate that the improved method not only resolves EWT frequency band division challenges but also effectively decomposes signal components compared to the VMD method.

Output Waveform Analysis of an Electro-hydraulic Vibrator Controlled by the Multiple Valves

The existing research of the electro-hydraulic vibrator mainly focuses on system stability, working frequency width and output waveform distortion. However, this high frequency performance of the electro-hydraulic vibrator is difficult to be improved greatly due to fast insufficiently frequency response of the servo valve itself and limited compensation capability of the control structure in the vibrator system. In this paper, to realize high frequency vibration, an improved two-dimensional valve （here within defined as a 2D valve） as a main control component is adopted to the parallel connection with a servo valve to control the electro-hydraulic vibrator, Because the output waveforms of this electro-hydraulic vibrator are incapable to be verified through timely feedback as in the conventional electro-hydraulic servo system, the analysis to the output waveform becomes crucial to the design and control of the electro-hydraulic vibrator. The mathematical models of hydraulic actuation mechanism and the orifice area of the parallel valves connection are established first. And then the vibration process is divided into two sections in terms of the direction of the flow, the analytical expression of the excited waveform is solved. Based on relationships exist between working states and the control parameters the analytical results, the vibration boundary positions and the are derived. Finally an experimental system was built to validate the theoretical analysis. It is verified that this electro-hydraulic vibration system could achieve high working frequency, up to 2 000 Hz. The excited waveform is similar to the sinnsoidal waveform. And the ascent and decent slopes of the waveforms are somewhat asymmetrical. This asymmetry is not only caused by the change of the direction of the elastic force but also dependent on the bias position of the vibration. Consequentky the distortion of effective working waveform is less tha~ 10%. This electro-hydraulic vibrator controlled by the multiple valves could not only greatly enhance the working frequency but also precisely control the vibration characteristic variables such as waveform shape.

Seismic Behavior of Diaphragm-Through Connections of Concrete-Filled Square Steel Tubular Columns and H-Shaped Steel Beams

Based on the introductions of a type of diaphragm-through connection between concrete-filled square steel tubular columns (CFSSTCs) and H-shaped steel beams,a finite element model of the connection is developed and used to investigate the seismic behavior of the connection.The results of the finite element model are validated by a set of cyclic loading tests.The cyclic loading tests and the finite element analyses indicate that the failure mode of the suggested connections is plastic hinge at the beam with inelastic rotation angle exceeding 0.04 rad.The suggested connections have sufficient strength,plastic deformation and energy dissipation capacity to be used in composite moment frames as beam-to-column rigid connections.

Adding body load modifies the vibratory sensation of the foot sole and affects the postural control

Background: Heavy backpacks are often used by soldiers and firefighters. Weight carrying could reduce the speed and efficiency in task completion by altering the foot sole sensitivity and postural control.Methods: In fifteen healthy subjects, we measured the changes in sensitivity to vibrations applied to the foot sole when standing upright or walking after load carrying(30% body weight). The participants were asked to judge different vibration amplitudes applied on the 2 nd or 5 th metatarsal head and the heel at two frequencies(25 and 150 Hz) to determine the vibration threshold and the global perceptual representation(Ψ)of the vibration amplitude(Φ)given by the Stevens power function(Ψ=k×Φ~n). Any increase in negative k value indicated a reduction in sensitivity to the lowest loads. Pedobarographic measurements, with computation of the center of pressure(COP) and its deviations, were performed during weight carrying.Results: The 25-Hz vibration threshold significantly increased after weight carrying when standing upright or walking.After standing with the added loads, the absolute negative k value increased for the 25 Hz frequency. After walking with the added loads, the k coefficient increased for the two vibration frequencies. Weight carrying significantly increased both the CoP surface and CoP lateral deviation.Conclusions: Our data show that weight carrying reduces the sensory pathways from the foot sole and accentuates the center of pressure deviations.

NUCLEATION AND CRYSTALLIZATION OF H-SHAPED(PS)_2PEG(PS)_2 BLOCK COPOLYMERS

A series of H-shaped （PS）2PEG（PS）2 block copolymers with different PS chain lengths were prepared. The influence of different confinements active on the crystallization and self-nucleation （SN） behavior of the PEG blocks was investigated by differential scanning calorimetry （DSC）. When the content of the crystalline block was high, a classical SN behavior was obtained. The block copolymer with PEG content of 49% （by weight） showed a classical SN behavior with a narrow self-nucleation domain and had bimodal crystallization exotherms. When the PEG dispersed as separated microdomains in the block copolymer, the self-nucleation domain disappeared and only annealing was observed.

Development of a vehicle-track interaction model to predict the vibratory benefits of rail grinding in the time domain

Imperfections in the wheel-rail contact are one of the main sources of generation of railway vibrations. Consequently, it is essential to take expensive corrective maintenance measures, the results of which may be unknown. In order to assess the effectiveness of these measures, this paper develops a vehicle-track interaction model in the time domain of a curved track with presence of rail corrugation on the inner rail. To characterize the behavior of the track, a numerical finite element model is developed using ANSYS software, while the behavior of the vehicle is characterized by a unidirectional model of two masses developed with VAMPIRE PRO software. The overloads obtained with the dynamic model are applied to the numerical model and then, the vibrational response of the track is obtained. Results are validated with real data and used to assess the effectiveness of rail grinding in the reduction of wheel-rail forces and the vibration generation phenomenon.

Vibration Measurement of Pedestrian Bridge Using Double Magnetic Suspension Vibrator Based on Wavelet Analysis

Aiming at the problem of pedestrian bridge vibration measurement,a vibration measurement system of pedestrian bridge with dual magnetic suspension vibrator structure was designed according to absolute vibration measurement principle. The relationship between the magnetic repulsion force of vibrator and its displacement was obtained by the experimental method and the least square fitting method. The vibration equations of two magnetic suspension vibrators were deduced respectively,and the measurement sensitivity of the system was deduced. The amplitude-frequency characteristic of the system was studied. A simulation model of vibrator measurement system with double magnetic suspension vibrator was established. The analysis shows that the sensitivity of the vibration measurement system with double magnetic suspension vibrator is higher than that with single magnetic suspension vibrator. The four vibration waveforms were measured,that is,no one passes through a pedestrian bridge,there are cars running under the pedestrian bridge,single pedestrian passes through the pedestrian bridge and multiple pedestrians pass through the pedestrian bridge. The multi-scale one-dimensional wavelet decomposition function was used to analyze the vibration signals. The vibration characteristics were obtained using one dimension wavelet decomposition function under four different conditions. Finally,the vibration waveforms of four cases were reconstructed. The measured results show that the vibration measurement system of pedestrian bridge with double magnetic suspension vibrator structure has high measurement sensitivity. The design has a certain value to monitor a pedestrian bridge.

Simulation Analysis and Experiment on Piezoelectric Cantilever Vibrator

Piezoelectric cantilever bimorph vibrator is the core component of piezoelectric inertial actuators.Piezoelectric cantilever bimorph vibrator with lumped mass at the end is studied,and a dynamic model is constructed by the proposed method of transforming symmetric electrical signal excitation to equivalent harmonic force excitation.Combining the theory and test,the single-degree-of-freedom damp vibration system consisting of the vibrator is analyzed and the full response is provided.Dynamical system modeling and simulation are conducted by software Matlab/Simulink.The output response of deflection,velocity,acceleration,driving force are solved using the input signal of equivalent harmonic force.Based on the data of theory,simulation and experiments,the deflection of vibrator is analyzed and compared under the excitation of sine wave signal.Result shows that the dynamic deflection results of vibrator from theory,simulation and experiments agree well with each other.The proposed modeling and analysis approaches of the single-degree-of-freedom damp vibration system consisting of the vibrator,have some reference significance for further research of piezoelectric inertial actuators.

A Review on Vibration Control of Multiple Cylinders Subjected to FlowInduced Vibrations

The fatigue damage caused by flow-induced vibration(FIV)is one of the major concerns for multiple cylindrical structures in many engineering applications.The FIV suppression is of great importance for the security of many cylindrical structures.Many active and passive control methods have been employed for the vibration suppression of an isolated cylinder undergoing vortex-induced vibrations(VIV).The FIV suppression methods are mainly extended to the multiple cylinders from the vibration control of the isolated cylinder.Due to the mutual interference between the multiple cylinders,the FIV mechanism is more complex than the VIV mechanism,which makes a great challenge for the FIV suppression.Some efforts have been devoted to vibration suppression of multiple cylinder systems undergoing FIV over the past two decades.The control methods,such as helical strakes,splitter plates,control rods and flexible sheets,are not always effective,depending on many influence factors,such as the spacing ratio,the arrangement geometrical shape,the flow velocity and the parameters of the vibration control devices.The FIV response,hydrodynamic features and wake patterns of the multiple cylinders equipped with vibration control devices are reviewed and summarized.The FIV suppression efficiency of the vibration control methods are analyzed and compared considering different influence factors.Further research on the FIV suppression of multiple cylinders is suggested to provide insight for the development of FIV control methods and promote engineering applications of FIV control methods.

Online asymmetry estimation for whole angle mode coriolis vibratory gyroscopes by high frequency injection

The whole angle mode gyroscope(WAMG)is considered to be the next generation architecture,but it is suffered from the asymmetry errors to conduct real products.This paper proposes a novel high frequency injection based approach for the error parameters online identification for the WAMG.The significance is that it can separate physical and error fingerprints to enable online calibration.The nonlinear WAMG dynamics are discretized to meet the requirement of numerical precision and computation efficiency.The optimized estimation methods are then constructed and compared to track asymmetry error parameters continuously.In the validation part,its results firstly prove that the proposed scheme can accurately identify constant asymmetry parameters with an overall tracking error of less than 1 ppm and the extreme numerical convergence can reach 10^(-12)ppm.Under the dynamic asymmetry variation condition,the root mean square errors(RMSE)indicate that the tracking accuracy can reach the level of10^(-3),which shows the robustness of the proposed scheme.In summary,the proposed method can effectively estimate the WAMG asymmetry errors online with satisfied performance and practical values.

Vibration Reduction by a Partitioned Dynamic Vibration Absorber with Acoustic Black Hole Features

Vibration quality is a vital indicator for assessing the progress of modern equipment.The dynamic vibration absorber(DVA)based on the acoustic black hole(ABH)feature is a new passive control method that manipulates waves.It offers efficient energy focalization and broad-spectrum vibration suppression,making it highly promising for applications in large equipment such as aircraft,trains,and ships.Despite previous advancements in ABH-DVA development,certain challenges remain,particularly in ensuring effective coupling with host structures during control.To address these issues,this study proposes a partitioned ABH-featured dynamic vibration absorber(PABH-DVA)with partitions in the radial direction of the disc.By employing a plate as the host structure,simulations and experiments were conducted,demonstrating that the PABH-DVA outperforms the original symmetric ABH-DVA in terms of damping performance.The study also calculated and compared the coupling coefficients of the two ABH-DVAs to uncover the mechanism behind the enhanced damping.Simulation results revealed that the PABH-DVA exhibits more coupled modes,occasionally with lower coupling coefficients than the symmetric ABH-DVA.The influence of frequency ratio and modal mass was further analyzed to explain the reasons behind the PABH-DVA's superior damping performance.Additionally,the study discussed the impact of the number of slits and their orientation.This research further explains the coupling mechanism between the ABH-DVA and the controlled structure,and provides new ideas for the further application of ABH in engineering.

Dynamics and vibration reduction performance of asymmetric tristable nonlinear energy sink

With its complex nonlinear dynamic behavior,the tristable system has shown excellent performance in areas such as energy harvesting and vibration suppression,and has attracted a lot of attention.In this paper,an asymmetric tristable design is proposed to improve the vibration suppression efficiency of nonlinear energy sinks(NESs)for the first time.The proposed asymmetric tristable NES(ATNES)is composed of a pair of oblique springs and a vertical spring.Then,the three stable states,symmetric and asymmetric,can be achieved by the adjustment of the distance and stiffness asymmetry of the oblique springs.The governing equations of a linear oscillator(LO)coupled with the ATNES are derived.The approximate analytical solution to the coupled system is obtained by the harmonic balance method(HBM)and verified numerically.The vibration suppression efficiency of three types of ATNES is compared.The results show that the asymmetric design can improve the efficiency of vibration reduction through comparing the chaotic motion of the NES oscillator between asymmetric steady states.In addition,compared with the symmetrical tristable NES(TNES),the ATNES can effectively control smaller structural vibrations.In other words,the ATNES can effectively solve the threshold problem of TNES failure to weak excitation.Therefore,this paper reveals the vibration reduction mechanism of the ATNES,and provides a pathway to expand the effective excitation amplitude range of the NES.

Extrusion process of 304L H-shaped stainless steel used in passive residual heat removal heat exchanger

304L H-shaped stainless steel is used as the support frame of the passive residual heat removal heat exchanger(PRHR HX) in a nuclear fission reactor. The extrusion process is adopted to manufacture the 304L H-shaped stainless steel. Finite element method simulation is herein used to analyze metal flow characteristics, optimize the extrusion die, and predict the extrusion force at different temperatures and speeds. A Φ400-mm container and Φ388-mm forging billet are selected, and the 304L H-shaped stainless steel is successfully manufactured using a Germany SMS 60 MN horizontal extruder. The mechanical properties and microstructure of the manufactured 304L H-shaped stainless steel meet the requirements of the PRHR HX, and the surfaces of the product pass the dye penetration test. The H-shaped stainless steels are used in Haiyang nuclear power plant in Shandong Province.

Natural Convection in an H-Shaped Porous EnclosureFilled with a Nanofluid

This study simulates natural convection flow resulting from heat partitions in an H-shaped enclosure filled with a nanofluid using an incompressible smoothed particle hydrodynamics(ISPH)method.The right area of the H-shaped enclosure is saturated with non-Darcy porous media.The center variable partitions of the H-shaped enclosure walls are kept at a high-temperature Th.The left and right walls of the H-shaped enclosure are positioned at a low temperature Tc and the other walls are adiabatic.In ISPH method,the source term in pressure Poisson equation(PPE)is modified.The influences of the controlling parameters on the temperature distributions,the velocity field and average Nusselt number are discussed.The performed simulations proofed that the length of the heated partitions augments the velocity field and temperature distributions in an H-shaped enclosure.Rayleigh number rises the fluid velocity and heat transfer in an H-shaped enclosure.The porous layer on the right side of the H-shaped enclosure at a lower Darcy parameter causes a high resistance force for the fluid flow and heat transfer characteristic inside an H-shaped enclosure.Added nanoparticles reduces the velocity field and enhances the heat transfer inside an H-shaped enclosure.

Design for Vibrator Field Experiment Based-on Vibrator-earth System

Source-generated energy in seismic vibrator records high frequency harmonic behavior. Conventional vibrator-earth coupling model was set up on the linear system. Some assumptions in the application of linear theory to the vibrator problem play an insignificant role in the overall coupling structure. Obviously, non-linear behaviors can be modeled using a “hard-spring” form of the Duffing equation. Model dedicates that a qualitatively similar harmonic component is present for a broad range of possible mathematical descriptions. After some qualitative analysis about the non-linear system, some conclusion can be drawn. Firstly, The design of the vibrator weight should be abided by two points as followed: In order to avoid decoupling for the vibrator to the earth, the weight should be greater than the peak of the driving force amplitude as to keep the resultant force pointing to the earth’s core. On the other hand, for the limited energy output, the vibrator overweight may damage the system high-frequency ability.Secondly, as the driving force frequency approaching to the ground hard-spring inherent frequency, the energy transmission was found to climb its peak from the system energy absorbed curve. At last, due to the non-linear coupling model system, its load curve would come into unstable frequency range, which might limit the application of the Vibroseis conventional sweeping pattern-linear sweep. A new sweeping pattern was listed: the driving signal was the pseudo-random sequence modulated by a fixed frequency cosine signal satisfying with the exploration precision and absorbing efficiency. The synthesized signal was ready to be realized by the electromagnetic driven system. Even the side-lobes noise of its auto-correlation function was restrained well. The theory coming from the Vibrator-earth coupling model was applied to the design of the Portable High-frequency Vibrator System (PHVS), and the good result was obtained. By the analysis of the vibrator base plate signal, the model was proved to be true. The exploration research on PHVS made a first step on its following optimal design.

Nonlinear optical properties of novel H-shaped chromophores

Novel and effective H-shaped chromophores were doped into polymethyl methacrylate （PMMA） to form guest-host polymer thin films. The measurement results of Maker fringe method show that the polymer thin films containing the H-shaped chromophores as a guest exhibit high second harmonic coefficients （d33） compared with other two-dimensional chromophores.

Shake table experimental study of cable-stayed bridges with two different design strategies of H-shaped towers

As one of the main load-carrying components of cable-stayed bridges,bridge towers are typically required to remain elastic even when subjected to severe ground motions with a 2%-3%probability of exceedance in 50 years.To fulfill this special requirement imposed by current seismic design codes,reinforcement ratios in the bridge towers have to be kept significantly higher than if limited ductility behavior of the tower is allowed.In addition,since the foundation capacity is closely related to the moment and shear capacities of the bridge tower,a large increase in bridge construction cost for elastically designed cable-stayed bridge is inevitable.To further investigate the possibility of limited ductility bridge tower design strategies,a new 1/20-scale cable-stayed bridge model with H-shaped bridge towers designed according to strong strut-weak tower column design was tested.The shake table experimental results are compared with a previous strong tower column-weak strut designed full bridge model.A comparison of the results show that ductility design with plastic hinges located on tower columns,i.e.,strong strut-weak tower column design,is another effective seismic design strategy that results in only small residual displacement at the top of the tower column,even under very severe earthquake excitations.

Fluidization and Transport of Vibrated Granular Matter:A Review of Landmark and Recent Contributions

We present a short retrospective review of the existing literature about the dynamics of(dry)granular matter under the effect of vibrations.The main objective is the development of an integrated resource where vital information about past findings and recent discoveries is provided in a single treatment.Special attention is paid to those works where successful synthetic routes to as-yet unknown phenomena were identified.Such landmark results are analyzed,while smoothly blending them with a history of the field and introducing possible categorizations of the prevalent dynamics.Although no classification is perfect,and it is hard to distillate general properties out of specific observations or realizations,two possible ways to interpret the existing results are defined according to the type of forcing or the emerging(ensuing)regime of motion.In particular,first results concerning the case where vibrations and gravity are concurrent(vertical shaking)are examined,then the companion situation with vibrations perpendicular to gravity(horizontal shaking)is described.Universality classes are introduced as follows:(1)Regimes where sand self-organizes leading to highly regular geometrical“pulsating”patterns(thin layer case);(2)Regimes where the material undergoes“fluidization”and develops an internal multicellular convective state(tick layers case);(3)Regimes where the free interface separating the sand from the overlying gas changes inclination or develops a kind a patterned configuration consisting of stable valleys and mountains or travelling waves;(4)Regimes where segregation is produced,i.e.,particles of a given size tend to be separated from the other grains(deep containers).Where possible,an analogy or parallelism is drawn with respect to the companion field of fluid-dynamics for which the assumption of“continuum”can be applied.

Snap-through behaviors and nonlinear vibrations of a bistable composite laminated cantilever shell:an experimental and numerical study

The snap-through behaviors and nonlinear vibrations are investigated for a bistable composite laminated cantilever shell subjected to transversal foundation excitation based on experimental and theoretical approaches.An improved experimental specimen is designed in order to satisfy the cantilever support boundary condition,which is composed of an asymmetric region and a symmetric region.The symmetric region of the experimental specimen is entirely clamped,which is rigidly connected to an electromagnetic shaker,while the asymmetric region remains free of constraint.Different motion paths are realized for the bistable cantilever shell by changing the input signal levels of the electromagnetic shaker,and the displacement responses of the shell are collected by the laser displacement sensors.The numerical simulation is conducted based on the established theoretical model of the bistable composite laminated cantilever shell,and an off-axis three-dimensional dynamic snap-through domain is obtained.The numerical solutions are in good agreement with the experimental results.The nonlinear stiffness characteristics,dynamic snap-through domain,and chaos and bifurcation behaviors of the shell are quantitatively analyzed.Due to the asymmetry of the boundary condition and the shell,the upper stable-state of the shell exhibits an obvious soft spring stiffness characteristic,and the lower stable-state shows a linear stiffness characteristic of the shell.

Dynamical Examinations of Vibrator Models, Describing Some Non Elastic Properties of Crystals

On the base of a vibrator atomic model the mechanical and thermal properties of the object are analyzed. The potential energy of the vibrator is represented by means of positive term with coordinate deflection in second power and negative term with deflection in fourth power. With the use of dynamical procedure of calculation, which permits to calculate mean deflection and root mean square amplitude of vibrations, the dependence of applied force from mean amplitude and temperature is calculated. This dependence shows a maximum (or minimum, when the direction of force is reversed), the height of which diminishes with rising temperature. When the force reaches the value of the maximum, the object does not elastic counteract to the force, and gliding begins. It is also considered a vibrator with positive term, containing the deflection in second power and a term, where the deflection treats in third power (Boguslawski vibrator). Exact calculations of the dependence of the force from the temperature in adiabatic process, where the entropy is maintained constant, shows that it is represented by means of a curve with a maximum, so that stretching leads to cooling till the point of maximum is reached.