High-Efficiency Dynamic Scanning Strategy for Powder Bed Fusion by Controlling Temperature Field of the Heat-Affected Zone

Improvement of fabrication efficiency and part performance was the main challenge for the large-scale powder bed fusion(PBF)process.In this study,a dynamic monitoring and feedback system of powder bed temperature field using an infrared thermal imager has been established and integrated into a four-laser PBF equipment with a working area of 2000 mm×2000 mm.The heat-affected zone(HAZ)temperature field has been controlled by adjusting the scanning speed dynamically.Simultaneously,the relationship among spot size,HAZ temperature,and part performance has been established.The fluctuation of the HAZ temperature in four-laser scanning areas was decreased from 30.85℃to 17.41℃.Thus,the consistency of the sintering performance of the produced large component has been improved.Based on the controllable temperature field,a dynamically adjusting strategy for laser spot size was proposed,by which the fabrication efficiency was improved up to 65.38%.The current research results were of great significance to the further industrial applications of large-scale PBF equipment.

Improving creep strength of the fine-grained heat-affected zone of novel 9Cr martensitic heat-resistant steel via modified thermo-mechanical treatment

The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power plants.In this work,the traditional thermo-mechanical treatment was modified via the replacement of hot-rolling with cold rolling,i.e.,normalizing,cold rolling,and tempering (NCT),which was developed to improve the creep strength of the FGHAZ in G115 steel weldments.The NCT treatment effectively promoted the dissolution of preformed M_(23)C_(6)particles and relieved the boundary segregation of C and Cr during welding thermal cycling,which accelerated the dispersed reprecipitation of M_(23)C_(6) particles within the fresh reaustenitized grains during post-weld heat treatment.In addition,the precipitation of Cu-rich phases and MX particles was promoted evidently due to the deformation-induced dislocations.As a result,the interacting actions between precipitates,dislocations,and boundaries during creep were reinforced considerably.Following this strategy,the creep rupture life of the FGHAZ in G115 steel weldments can be prolonged by 18.6%,which can further push the application of G115 steel in USC power plants.

Effect of Dynamic Strain Aging on Hardness in the Heat-Affected Zone of SUS316 Steel Welds

DSA(dynamic strain aging)phenomenon in SUS316 steel was investigated using isothermal and non-isothermal tensile tests of simulated HAZ(heat-affected zone)thermal cycles.Isothermal tensile tests were performed on SUS316 in the peak temperature range of 20-700°C,with strain rates varying from 4.2×10^(-3)to 4.2×10^(-5)s^(-1).Based on the appearance of discontinuous plastic flows,expressed as serrations,and the hardening phenomenon of the tensile samples,the conditions for the occurrence of DSA in the SUS316 steel were investigated.Furthermore,the extent of hardening due to DSA was evaluated by comparing the hardness values of the SUS316 and SUS316EHP steels after the tensile tests.To confirm the effect of DSA on hardness in the HAZ of the welded SUS316 steel,non-isothermal tensile tests of the simulated HAZ thermal cycles were performed using a Thermec Master.The relationship between the increase in Vickers hardness due to DSA and the strain in the HAZ was determined;the effect of DSA on hardness in the HAZ could be predicted.The DSA in SUS316 steel was found to be mainly attributed to the dynamic interaction of dislocations with C and N interstitial atoms during high-temperature deformation.

Effects of Electrode Types on the Microstructure, Tensile and Hardness Properties of 304 L Austenitic Stainless Steel Heat-Affected Zone (HAZ)

Submerged arc welding (SAW) has been well utilised for the production of weld joints in 304 L ASS for various industrial application. However, effective performance of the material in service has been hampered by improper choice of electrode. Therefore, in this study, effects of different types of electrode on the microstructure and tensile property of type 304 L austenitic stainless steel heat-affected zone (HAZ) were studied. Chemical composition of the as-received sample was determined. A number of samples were cut from the as-received sample. Afterwards, two half were joined together with 308 L, 312 L and 316 electrodes at a controlled welding speed, current and voltage of 4.6 mm/s, 160 A and 30 V to produce a constant heat input of 626.09 J/mm. An automatic SAW machine with Model Type: DX3-301, and Frequency: 50 Hz was used. And based on ASTM standard, tensile and hardness samples were prepared from the as-received and HAZs. Tensile and hardness measurements were made. Also, specimens for microscopy studies were prepared from the HAZ and as-received samples. From the results, microstructures of the HAZs revealed varied volume fraction of austenite and ferrite phases and grain sizes, and at austenite and ferrite grain boundaries, chromium carbide formation and precipitation were observed. The weld joint produced with 308 L electrode revealed optimum UTS value and YS value of 475 and 325 respectively. While weld joint produced with 316 L electrode has superior ductility of value 41%. Irrespective of the types of electrode used, the as-received sample revealed superior tensile properties over the weld joints. Also, optimum hardness value of 45.7 HRA was obtained with 308 L. Hardness value of the as-received sample was higher than that of HAZ samples.

In situ observation of austenite grain growth behavior in the simulated coarse-grained heat-affected zone of Ti-microalloyed steels

The austenite grain growth behavior in a simulated coarse-grained heat-affected zone during thermal cycling was investigated via in situ observation. Austenite grains nucleated at ferrite grain boundaries and then grew in different directions through movement of grain boundaries into the ferrite phase. Subsequently, the adjacent austenite grains impinged against each other during the α→γtransformation. After the α→γ transformation, austenite grains coarsened via the coalescence of small grains and via boundary migration between grains. The growth process of austenite grains was a continuous process during heating, isothermal holding, and cooling in simulated thermal cycling. Abundant finely dispersed nanoscale TiN particles in a steel specimen containing 0.012wt% Ti effectively retarded the grain boundary migration, which resulted in refined austenite grains. When the Ti concentration in the steel was increased, the number of TiN particles de- creased and their size coarsened. The big particles were not effective in pinning the austenite grain boundary movement and resulted in coarse austenite grains.

Liquation cracking in the heat-affected zone of IN939 superalloy tungsten inert gas weldments

The main aim of this study was to investigate liquation cracking in the heat-affected zone(HAZ)of the IN939 superalloy upon tungsten inert gas welding.A solid solution and age-hardenable filler metals were further studied.On the pre-weld heat-treated samples,upon solving the secondaryγ′particles in the matrix,primaryγ′particles in the base metal grew to"ogdoadically diced cubes"of about 2μm in side lengths.The pre-weld heat treatment reduced the hardness of the base metal to about HV 310.Microstructural studies using optical and fieldemission scanning electron microscopy revealed that the IN939 alloy was susceptible to liquation cracking in the HAZ.The constitutional melting of the secondary,eutectic,and Zr-rich phases promoted the liquation cracking in the HAZ.The microstructure of the weld fusion zones showed the presence of fine spheroidalγ′particles with sizes of about 0.2μm after the post-weld heat treatment,which increased the hardness of the weld pools to about HV 350 and 380 for the Hastelloy X and IN718 filler metals,respectively.Application of a suitable solid solution filler metal could partially reduce the liquation cracking in the HAZ of IN939 alloy.

Microstructure and embrittlement of the fine-grained heat-affected zone of ASTM4130 steel

The mechanical properties and microstructure features of the fine-grained heat-affected zone（FGHAZ） of ASTM4130 steel was investigated by optical microscope（OM）,scanning electron microscope（SEM）,transmission electron microscope（TEM）,and welding thermal simulation test.It is found that serious embrittlement occurs in the FGHAZ with an 81.37% decrease of toughness,compared with that of the base metal.Microstructure analysis reveals that the FGHAZ is mainly composed of acicular,equiaxed ferrite,granular ferrite,martensite,and martensite-austenite（M-A） constituent.The FGHAZ embrittlement is mainly induced by granular ferrite because of carbides located at its boundaries and sub-boundaries.Meanwhile,the existence of martensite and M-A constituent,which distribute in a discontinuous network,is also detrimental to the mechanical properties.

Microstructure and toughness of coarse grain heat-affected zone for Nb-microalloyed X80 pipeline steel

Based on welding thermal simulation on Nb-microaUoyed XSO pipeline stee! using Gleeble-3500 thermal simulation equipment, microstlttcture and impact toughness in coarse grain heat-affected zone （CGHAZ） under different welding parameters were investigated in this paper. The results show that high heat inputs with low preheats or low heat inputs with high preheats should be applied to achieve high impact toughness. Coarse original austenite grains may lower impact toughness. CGHAZ microstructure is mostly composed of upper bainite, granular bainite and lath bainite. The phase composition of microstructure and the quantity, size, shape of M/A constituents both have effects on impact toughness.

The softening prediction of HSLA steel heat-affected zone based on the grey system

The high-strength low-alloy（ HSLA ） steel heat-affected zone （HAZ）softening was predicted using a grey model. HSLA steel DILLIMAX690E, NK-HITEN61OU2 and BHW35 were taken as examples in the research on ultra-narrow gap automatic welding technology. Test results turned out to be that the errors between the values calculated by the Grey Model （GM） （ 1,1 ） model and their actual value were less than 2%, indicating that the grey prediction method could accurately reflect the actual situation of the high-strength low-alloy steel heat-affected zone softening. This method will play a crucial role in guiding the applications of HSLA steel welded structures in the future.

Influence of different microstructural features on impact toughness and crack initiation behavior of coarse grain heat-affected zone in X80 pipeline steel

Coarse grain heat-affected zone samples of X80 pipeline steel under different heat inputs were obtained through thermal welding simulation experiments with Gleeble 3500.Charpy impact tests and a combination of multiscale characterizations were conducted to investigate the influence of various microstructural features on impact toughness and crack initiation behavior.The results prove that, as the heat input increases, the number of M/A components increases, thereby degrading toughness and increasing hardness.Meanwhile, more M/A constituents tend to aggregate on prior austenite grain boundaries(PAGBs),and the overall dimensions of M/A and the width and volume fraction of the lath martensite substructure inside M/A islands would increase as well.These changes make intersections between boundary M/As and PAGBs become one of the preferred sites for crack initiation.In addition, only large-sized grotesque inclusions can act as a direct inducement of crack initiation.

Heat-affected zone in pulsed laser cutting of titanium alloy

For the machining of bladed ring parts of an aeroengine, experiments on Nd∶YAG pulsed laser cutting of TC1 titanium alloy sheet were carried out to investigate the influences of laser cutting parameters on heat-affected zone (HAZ). The selected laser cut samples were photographed by scanning electron microscopy. The results show that the microstructure in HAZ layers is characterized by metastable acicular martensite grains with a slight increase of hardness by 10%. The thickness of HAZ layers was studied as a function of laser cutting parameters. Medium pulse energy, higher pulse rate, higher cutting speed and argon at higher pressures help to reduce the thickness of HAZ layers.

Effect of Zr-Ti combined deoxidation on impact toughness of coarse-grained heat-affected zone with high heat input welding

In this study, the effects of Zr-Ti combined deoxidation and AI deoxidation on the impact toughness of coarse- grained heat-affected zone in high-strength low-alloy steels were investigated. More fine oxides were formed in the Zr-Ti-killed steel than in Al-killed steel. It was also found that more acicular ferrite grains were formed in the coarse-grained heat-affected zone in the Zr-Ti-killed steel than in Al-killed steel. The impact toughness of coarse-grained heat-affected zone of Zr-Ti-kiUed steel was higher than that of Al-killed steel. The good impact toughness was attributable to the pinning effect of fine oxides and the formation of acicular ferrite grains on fine oxides.

High-temperature creep properties of fine grained heat-affected zone in P92 weldment

The simulated fine grained heat-affected zone (FGHAZ) specimens for P92 welded joints were prepared by heat treatment, then the creep tests were carried out at 650 ℃ under the applied stress of 90-120 MPa to investigate high-temperature creep behavior of FGHAZ. The results show that the creep property of FGHAZ is much inferior to that of the base metal, which exhibits the much higher steady creep rate and shorter time to creep fracture. The power law equation can describe the steady creep rate dependence on applied stress, indicating that the stress exponent n of FGHAZ is distinguished between two regions with n=15.1 at high stresses (more than 100 MPa) and n=8.64 at lower stresses. Based on Monkman-Grant equation, the relationship between the secondary creep rate and time to rupture is obtained to evaluate the creep life of FGHAZ with the applied stress above 100 MPa.

Study on laser welded heat-affected zone in new ultralow carbon bainitic steel

800 MPa grade ultralow carbon bainitic （NULCB） steel is the recently developed new generation steel, which was produced by thermo mechanical controlled processing ＆ relaxation-precipitation controlling transformation （TMCP＆RPC） tech- nique. The microstructure and the mechanical properties of the heat-affected zone （HAZ） in NULCB steel under laser welding conditions were investigated by using a Gleeble-1500 thermal simulator. The experimental results indicate that the simplex microstructure in the HAZ is granular bainite that consists of bainite-ferrite （BF） lath and M-A constituent when the cooling time from 800 to 500℃ （t8/5） is 0.3-30 s, and the M-A constituent consists of twinned martensite and residual austenite. As t8/5 increases, the hardness and tensile strength of HAZ decreases, but they are higher than that of the base metal, indicating the absence of softened zone after laser welding. The impact toughness of HAZ increases at first and then decreases when t8/5 increases. The impact energy of HAZ is much higher than that of the base metal when t8/5 is between 3 and 15 s. It indicates that excellent low temperature toughness can be obtained under appropriate laser welding conditions.

Simulation research on heat-affected zone of the NiTi alloy plasma arc welded joints

In order to study the compositions and properties of NiTi alloy plasma arc welded joints, different temperatures of the heat-affected zone（HAZ） are simulated. Temperatures are set at 20 ℃, 400 ℃, 500 ℃, 600 ℃, 700 ℃, 800 ℃, 900 ℃ and 1 000 ℃. X-ray diffraction results of the thermal simulated specimens show that NiTi2 phase emerges in the alloy when the temperature is between 500 ℃ and 800 ℃, while NiTi2 and Ni3 Ti phases emerge when the temperature is between 800 ℃ and 1 000 ℃. Tensile strengths of specimens at 600 ℃ and 900 ℃ are only 68. 0% and 61.3% of the strength at the room temperature respectively due to the emergence of NiTi2 and Ni3 Ti phases.

Study on local embrittlement of welding heat-affected zone in XSO pipeline steels

The relationship between the microstructure and toughness of welding heat-affected zone in XSO grade pipeline steels is studied. It is found that the intercritical reheated coarse-grained heat-affected zone （ICCGHAZ） of experimental steels has the lowest toughness values when the secondary peak temperature is at intercritical （ α ＋ γ ） region during multi-pass welding. The local embrittlement is mainly attributed to the morphology, amount and size of M-A constituent. It is also found that the microstructural inhabitanee at ICCGHAZ has a deleterious effect on the toughness. On the basis of above experimental results, it is suggested that the local embrittlement should be prevented by using pre-heating thermal cycle which could eliminate the microstructural inhabitance and using post-heating thermal cycle which could improve the morphology, amount and size of MA constituent.

Influence of the secondary welding thermal cycle on the microstructure and property of coarse grain heat-affected zone in an X100 pipeline steel

The influence of the secondary thermal cycle on the microstructure of coarse grain heat-affected zone in an XIO0 pipeline steel was investigated by means of a thermal simulation technique and microscopic analysis method. The property of coarse grain heat-affected zone was characterized by Charpy V-Notch impact properties testing. The results indicated that the experimental steel exhibited local brittleness of intercritically reheated coarse-grained heat-affected zone when the peak tempera- ture of secondary thermal cycle was in the range of two phases region （ ~ and 3/）. There were two main reasons for the local brittleness. The first was that the microstructures of intercritically reheated coarse-grained heat-affected zone were not fined although partial grain recrystallization occurred. The second was that M-A islands, which had the higher content, larger size and higher hardness, existed in intercritically reheated coarse-grained heat-affected zone.

EFFECT OF LOCAL HARD ZONE ONFRACTURE INITIATION OF WELD HAZ

The effect of the local hard zone (LHZ) distributed in the coarse grained HAZ (CGHAZ) has been analyzed by 2-dimensional FEM on a mechanical model of the weld CGHAZ. The existence of the LHZ elevates considerably the stress in LHZ and causes the discontinuity of strain at the boundary between the LHZ and the matrix. The stress distribution in the LHZ is strongly affected by the shape of the LHZ. In a slender LHZ almost the whole region in the LHZ is exposed to elevated stress, whereas in the massive LHZ only the edge region sustains high stress. The longer the LHZ becomes, the more the highly stressed area, and the peak stress in the LHZ grows even under the same volume fraction of the LHZ. These results indicate that the slender LHZ brings about unstable fracture at a lower load level than the blocky LHZ. This tendency was confirmed by CTOD test results on the weld CGHAZ of a high-strength steel. The CGHAZ with elongated M-A constituents fractures at apparently lower critical CTOD than the CGHAZ with massive M-A constituents. In conclusion, the control of the shape of the M-A constituent has a striking effect on the toughness improvement of CGHAZ.

Changes in microstructure and properties of weld heat-affected zone of high-strength low-alloy steel

The evolution of the microstructure and toughness of APL5L X80 pipeline steel after thermal welding simulation was investigated by X-ray diffraction,electron backscatter diffraction,and transmission electron microscopy.The results indicated that primary heat-affected zones can be divided into weld,coarse-grained,fine-grained,intercritical,and sub-critical zones.The microstructure of the weld zone is mainly composed of bainitic ferrite and a small amount of granular bainite;however,the original austenite grains are distributed in the columnar grains.The structure of the coarse-grained zone is similar to that of the weld zone,but the original austenite grains are equiaxed.In contrast,the microstructure in the fine-grained zone is dominated by fine granular bainite,and the effective grain size is only 8.15μm,thus providing the highest toughness in the entire heat-affected zone.The intercritical and subcritical zones were brittle valley regions,and the microstructure was dominated by granular bainite.However,the martensite-austenite(M/A)constituents are present in island chains along the grain boundaries,and the coarse size of the M/A constituents seriously reduces the toughness.The results of the crack propagation analyzes revealed that high-angle grain boundaries can significantly slow down crack growth and change the crack direction,thereby increasing the material toughness.The impact toughness of the low-temperature tempering zone was equivalent to that of the columnar grain zone,and the impact toughness was between those of the critical and fine-grained zones.

局部硬化区周围的应力应变特性对HAZ断裂行为的影响

从力学的观点出发，将高强钢焊接热影响区粗晶区中硬化组织ＭＡ组元视作局部硬化区（ＬＨＺ）．采用二维有限元数值方法分析了ＬＨＺ周围的应力应变分布．结果表明：ＬＨＺ存在时，ＬＨＺ内部应力升高，ＬＨＺ与基体产生变形差．这意味着ＬＨＺ内部或ＬＨＺ与基体界面容易引发裂纹．最后通过对ＴＭＣＰ钢焊接热影响区微观裂纹的实验观察。