Electromagnetic stirring is one of the widely applied techniques to modify the quality of casting billets.Different from conventional rotate stirring,the helical stirring is more professional in assisting multi-dimens...Electromagnetic stirring is one of the widely applied techniques to modify the quality of casting billets.Different from conventional rotate stirring,the helical stirring is more professional in assisting multi-dimensional flow of molten metal and eliminating solidification defects.In this study,the single-winding helical stirring(SWHS)was introduced,offering advantages such as smaller volume and lower electromagnetic shielding compared to traditional helical stirring methods.Following a comprehensive numerical simulation,the stirring parameters of SWHS were adjusted to yoke inclination angle of 43°and frequency of 12 Hz.The higher electromagnetic force and flow velocity in drawing direction,as well as the lower temperature gradient induced by the SWHS,are positive factors for homogeneous solidification of billet.The experimental results on Al-8%Si alloy and 0.4%C-1.1%Mn steel demonstrate that compared to rotate stirring,the SWHS process can induce better billet quality and is more effective in accelerating the equiaxed expansion and reducing element segregation.The SWHS process can enhance the equiaxed ratio of the billet by 58.3%and reduce segregation degree of carbon element by 10.97%.Consequently,SWHS holds great promise as a potential approach for improving the quality of continuous casting billets.展开更多
Based on high magnetic field helicon experiment(HMHX), HELIC code was used to study the effect of different magnetic fields on the power deposition under parabolic distribution. This paper is divided into three parts:...Based on high magnetic field helicon experiment(HMHX), HELIC code was used to study the effect of different magnetic fields on the power deposition under parabolic distribution. This paper is divided into three parts: preliminary calculation, actual discharge experiment and calculation. The results of preliminary calculation show that a magnetic field that is too small or too large cannot produce a good power deposition effect. When the magnetic field strength is 1200 Gs,a better power deposition can be obtained. The actual discharge experiment illustrates that the change of the magnetic field will have a certain influence on the discharge phenomenon. Finally, the results of verification calculation successfully verify the accuracy of the results of preliminary simulation. The results show that in the actual discharge experiment, it can achieve the best deposition effect when the magnetic field is 1185 Gs.展开更多
In this paper, the problem of finding exact solutions to the magnetohydrodynamic(MHD) equations in the presence of incompressible mass flows with helical symmetry is considered. For ideal flows, a similarity reduction...In this paper, the problem of finding exact solutions to the magnetohydrodynamic(MHD) equations in the presence of incompressible mass flows with helical symmetry is considered. For ideal flows, a similarity reduction method is used to obtain exact solutions for several MHD flows with nonlinear variable Mach number. For resistive flows parallel to a magnetic field, the governing equilibrium equation is derived. The MHD equilibrium state of a helically symmetric incompressible flow is governed by a second-order elliptic partial differential equation(PDE) for the helical magnetic flux function. Exact solutions for the latter equation are obtained. Also, the equilibrium equations of a gravitating plasma with incompressible flow are derived.展开更多
Helical anchor is a kind of novel foundation for floating offshore wind turbines,which should be subjected to combined tensile loading caused by wind,wave and current.However,the research about the capacity of helical...Helical anchor is a kind of novel foundation for floating offshore wind turbines,which should be subjected to combined tensile loading caused by wind,wave and current.However,the research about the capacity of helical anchor was mainly examined under uniaxial loading and scarcely explored under combined loading.In this study,three-dimensional finite element limit analysis is adopted to assess the bearing capacities of single-plate rigid helical anchors with different ratios of helix to shaft diameter,D_(H)/D_(S) and embedment ratios L/D_(S).Result shows that the vertical,horizontal and moment bearing capacities increase with increasing D_(H)/D_(S) and L/D_(S).The normalized V-H failure envelopes expands with increasing L/D_(S),while the normalized V-M failure envelopes tend to contract with the increase of D_(H)/D_(S).With increasing D_(H)/D_(S) or decreasing L/D_(S),the normalized H-M failure envelopes expand when the horizontal and moment loading act in the same direction and contract when they act in the opposite direction.The effect of D_(H)/D_(S) and L/D_(S) on the shape of H-M failure envelope become insignificant when L/D_(S)≥4.A series of failure mechanisms under different loading conditions were observed and can be used to explain the trend.Besides,a series of approximate expressions were proposed to fit the uniaxial bearing capacities and the failure envelopes.展开更多
The aim of this study is the numerical analysis of the melting process of the phase change material(PCM)in a spiral coil.The space between the inner tube and outer shell is filled with RT-50 as PCM.Moreover,the hybrid...The aim of this study is the numerical analysis of the melting process of the phase change material(PCM)in a spiral coil.The space between the inner tube and outer shell is filled with RT-50 as PCM.Moreover,the hybrid nanofluid(with a carbon component)flows through the inner tube.The novelty of this work is to use different configurations of fin and different percentage of hybrid nanoparticles(SWCNTs-Cu O)on the PCM melting process.In the numerical model created by ANSYS-Fluent,the effect of various inlet temperatures is investigated.The results indicate that the extended surface created by extra fin has a dominant effect on melting time,so by adding the third fin,the melting time is reduced by 39.24%.The next most influential factor in PCM melting is the inlet temperature of the working fluid,so that 10°C increment of temperature result in the PCM melting time decreased by 35.41%.展开更多
The goal of this research is to look at multi-target optimization of a two-stage helical gearbox in order to determine the best key design elements for reducing gearbox height and enhancing gearbox efficiency.To do th...The goal of this research is to look at multi-target optimization of a two-stage helical gearbox in order to determine the best key design elements for reducing gearbox height and enhancing gearbox efficiency.To do this,the method known as Taguchi and GRA(Grey Relation Analysis)were used in two stages to address the problem.The single-objective optimization problem was addressed first to close the gap between variable levels,and then the multi-objective optimization problem was solved to determine the best primary design variables.The first and second stage CWFWs(Coefficients of Wheel Face Width),ACS(Permissible Contact Stresses),and first stage gear ratio were also calculated.The study’s findings were utilized to identify the best values for five critical design aspects of a two-stage helical gearbox.展开更多
Helicity is defined as H : V ω, where V and ω are the velocity and vorticity vectors, respectively. Many works have pointed out that the larger the helicity is, the longer the life cycle of the weather system is. H...Helicity is defined as H : V ω, where V and ω are the velocity and vorticity vectors, respectively. Many works have pointed out that the larger the helicity is, the longer the life cycle of the weather system is. However, the direct relationship of the helicity to the evolution of the weather system is not quite clear. In this paper, the concept of helicity is generalized as shearing wind helicity (SWH). Dynamically, it is found that the average SWH is directly related to the increase of the average cyclonic rotation of the weather system. Physically, it is also pointed out that the SWH, as a matter of fact, is the sum of the torsion terms and the divergence term in the vorticity equation. Thermal wind helicity (TWH), as a derivative of SWH, is also discussed here because it links the temperature field and the vertical wind field. These two quantities may be effective for diagnosing a weather system. This paper applies these two quantities in cylindrical coordinates to study the development of Hurricane Andrew to validate their practical use. Through analyzing the hurricane, it is found that TWH can well describe the characteristics of the hurricane such as the strong convection and release of latent heat. SWH is not only a good quantity for diagnosing the weather system, but also an effective one for diagnosing the development of the hurricane.展开更多
The characteristics of helicity in a hurricane are presented by calculating the MM5 model output in addition to theoretical analysis. It is found that helicity in a hurricane mainly depends on its horizontal component...The characteristics of helicity in a hurricane are presented by calculating the MM5 model output in addition to theoretical analysis. It is found that helicity in a hurricane mainly depends on its horizontal component, whose magnitude is about 100 to 1000 times larger than its vertical component. It is also found that helicity is approximately conserved in the hurricane. Since the fluid has the intention to adjust the wind shear to satisfy the conservation of helicity, the horizontal vorticity is even larger than the vertical vorticity, and the three-dimensional vortices slant to the horizontal plane except in the inner eye. There are significant horizontal vortices and inhomogeneous helical flows in the hurricane. The formation of the spiral rainband is discussed by using the law of horizontal helical flows. It is closely related to the horizontal strong vortices and inhomogeneous helical flows.展开更多
In this work, the formation sites, helical parameters and hydrogen bond positions of Konjac glucomannan molecular helices were investigated using molecular dynamic simulation method. To our interest, the KGM chain is ...In this work, the formation sites, helical parameters and hydrogen bond positions of Konjac glucomannan molecular helices were investigated using molecular dynamic simulation method. To our interest, the KGM chain is mainly composed by local left and right helix struetttres. The formation sites of KGM chain might locate at the chain-segments containing acetyl groups, and the left helix is the favorable conformation of KGM. Temperature-dependent molecule conformation study indicates that the right helix is dominant when the temperature is lower than 343 K, above which, however, the left helix is dominating (right helix disappears). In addition, intramolecular hydrogen bonds in the left helix can be found at the -OH groups on C(2), C(4) and C(6) of mannose residues; comparably, the intramolecular hydrogen bonds in the right helix can be mainly observed at the -OH groups on C(4) and C(6) of the mannose residues and C(3) of the glucose residues. In conclusion, molecular dynamic simulation is an efficient method for the microscopic conformation study of glucomannan molecular helices.展开更多
In this article, we investigate three-dimensional solution with helical symmetry in a gap between two concentric rotating cylinders, inside is a helicoidal surface(screw propeller)while outside is a cylindrical surf...In this article, we investigate three-dimensional solution with helical symmetry in a gap between two concentric rotating cylinders, inside is a helicoidal surface(screw propeller)while outside is a cylindrical surface. Establish the partial differential equations and its variational formulation satisfied by a helical solution in a helical coordinate system using tensor analysis method, we provide a computational method for the power and propulsion of the screw. The existence and uniqueness of weak helical solutions are proved.展开更多
The stability of platform structure is the paramount guarantee of the safe operation of the offshore floating wind turbine. The NREL 5MW floating wind turbine is established based on the OC3-Hywind Spar Buoy platform ...The stability of platform structure is the paramount guarantee of the safe operation of the offshore floating wind turbine. The NREL 5MW floating wind turbine is established based on the OC3-Hywind Spar Buoy platform with the supplement of helical strakes for the purpose to analyze the impact of helical strakes on the dynamic response of the floating wind turbine Spar platform. The dynamic response of floating wind turbine Spar platform under wind, wave and current loading from the impact of number, height and pitch ratio of the helical strakes is analysed by the radiation and diffraction theory, the finite element method and orthogonal design method. The result reveals that the helical strakes can effectively inhibit the dynamic response of the platform but enlarge the wave exciting force; the best parameter combination is two pieces of helical strakes with the height of 15%D (D is the diameter of the platform) and the pitch ratio of 5; the height of the helical strake and its pitch ratio have significant influence on pitch response.展开更多
The shell side flow fields of both sextant and trisection helical baffle heat exchangers are presented on meridian and multilayer hexagon slices.It verifies that the performance of sextant schemes is better than those...The shell side flow fields of both sextant and trisection helical baffle heat exchangers are presented on meridian and multilayer hexagon slices.It verifies that the performance of sextant schemes is better than those of the other kinds of helical baffle heat exchangers.The main mechanisms are due to the restricted leakage flow in the minimized gaps with increased baffle number and by one row of tubes dampen the leakage flow in the circumferential overlapped area of the adjacent helical baffles.The performance features were simulated on two different angled sextant helical heat exchangers and each compared with two trisection ones of either identical helical pitch or identical incline angle.The results verified that the performances of helical heat exchangers are mainly determined by the helical pitch rather than the baffle incline angle.The average values of comprehensive index hoΔpo-1/3 of the trisection helical schemes T-24.1°and T-29.7°are correspondingly 3.47%and 3.34%lower than those of the sextant ones X-20°and X-25°with identical helical pitches.The comparison results show that the average values of shell side h.t.c.hoand comprehensive index hoΔpo-1/3 of the optimal dual helix sextant scheme DX30°are respectively 7.22%and 23.56%higher than those of the segment scheme S100.展开更多
Objective: To evaluate the short-term clinical outcomes of intracranial germinoma patients treated with craniospinal irradiation (CSI) using helical tomotherapy (HT) system in our center. Methods: Twenty-three p...Objective: To evaluate the short-term clinical outcomes of intracranial germinoma patients treated with craniospinal irradiation (CSI) using helical tomotherapy (HT) system in our center. Methods: Twenty-three patients who were treated with CSI in our center from January 2008 to July 2012 were collected, with an average age of 20. M1 of the patients' CSI used the HT system. The total doses were 27-36 Gy/15-20 F (1.5-2 Gy per fraction), and total local doses were 46-60 Gy/30-50 F (5 fractions per week). M1 female patients for CSI were treated with left-right parallel-opposed field irradiation to protect their ovarian functions. Median follow-up time was 30.9 months (range, 5-67 months). The SPSS19.0 software was used, and the overall survival (OS) was calculated using the Kaplan-Meier method. Results: Among 17 patients with assessable tumors, 9 cases (52.9%) were CR, 7 cases (41.2%) were PR, and 1 case (5.9%) was SD. Hematological toxicity was the severest side-effect occurred in the procedure of CSI. The level 1-4 acute leukopenia were 8.7%, 30.4%, 34.8% and 21.7% and the level 1-4 acute thrombopenia were 8.7%, 30.4%, 21.7% and 8.7%, respectively. Conclusions: For primary intracranial germinomas, HT can be used to implement CSI for simplifying radiotherapy procedures, improving radiotherapy accuracy, enhancing protection of peripheral organs at risk (ORA) and guaranteeing therapeutic effects. With the acceptable acute and long-term toxicity, CSI using HT in intracranial germinoma patients can be a safe and alternative mode.展开更多
An experimental study on a bare flexible cylinder as well as cylinders fitted with two types of cross-sectioned helical strakes was carried out in a towing tank. The main purpose of this paper is to investigate the ef...An experimental study on a bare flexible cylinder as well as cylinders fitted with two types of cross-sectioned helical strakes was carried out in a towing tank. The main purpose of this paper is to investigate the effects of strakes’ cross-section on the vortex-induced vibrations (VIV) suppression of a flexible cylinder. The square-sectioned and round-sectioned helical strakes were selected in the experimental tests. The uniform current was generated by towing the cylinder models along the tank using a towing carriage. The Reynolds number was in the range of 800–16000. The strain responses were measured by the strain gages in cross-flow (CF) and in-line (IL) directions. A modal analysis method was adopted to obtain the displacement responses using the strain signals in different measurement positions. The comparison of the experimental results among the bare cylinder, square-sectioned straked cylinder and round-sectioned straked cylinder was performed. The helical strakes can effectively reduce the strain amplitude, displacement amplitude, response frequencies and dominant modes of a flexible cylinder excited by VIV. And the mean drag coefficients of straked cylinders were approximately consistent with each other. In addition, the square-sectioned and round-sectioned strakes nearly share the similar VIV reduction behaviors. Sometimes, the strakes with round-section represent more excellent effects on the VIV suppression of response frequency than those with square-section.展开更多
A stranded wires helical spring is formed of a multilayer and coaxial strand of several wires twisted together with the same direction of spiral. Compared with the conventional single wire spring, the stranded wires h...A stranded wires helical spring is formed of a multilayer and coaxial strand of several wires twisted together with the same direction of spiral. Compared with the conventional single wire spring, the stranded wires helical spring has the notable predominance in strength, damping and vibration reduction, which is usually used in aircraft engines, automatic weapons, etc. However, due to its complicated structure, the precise computation of its strength and rigidity need be a correct mathematical model, which then will be imported to finite element analysis software for solutions. Equations on solving geometric parameters, such as external diameters of strands and screw pitches of wires, are put forward in the paper. It also proposes a novel methodology on solving geometric parameters and establishing entity models of the stranded wires helical spring, which provides foundation of computing mechanical parameters by FEA. Then mathematical models on the centre line of the strand and the surface curve of each wire, after closing two ends in a spring, are proposed. Finally, geometric parameters are solved in a case study, and a 3D entity model of a spring with 3 layers and 16 wires is established, which has validated the accuracy of the proposed methodology and the 3D entity mathematical model. The method provides a new way to design stranded wire helical spring.展开更多
The formation mechanism and stability of konjac glucomannan (KGM) helical structure were investigated by molecular dynamic simulation and experimental method. The results indicate that the molecular conformation of ...The formation mechanism and stability of konjac glucomannan (KGM) helical structure were investigated by molecular dynamic simulation and experimental method. The results indicate that the molecular conformation of KGM is a non-typical helical structure. In detail, helical structure of KGM is mainly sustained by acetyl group, whose size and stability are affected by the molecular polymerization degree of KGM. In vacuum among the non-bonding interactions, electrostatic force is the greatest factor affecting its helical structure, but in water solution, hydrogen bond affects the helical arrangement greatly. To our interest, temperature exhibits a reversible destroying effect to some extent; the helical structure will disappear completely and present a ruleless clew-like arrangement till 341 K. This work suggests that the method of combining molecular dynamic simulation and experiment tools can be effective in the study of KGM helical structure.展开更多
BACKGROUND: Multirow-detector helical CT (MDCT) allows faster Z-axis coverage and improves longitudinal re- solution to scan the entire liver. This study was to evaluate the value of multiphase hepatic CT scans using ...BACKGROUND: Multirow-detector helical CT (MDCT) allows faster Z-axis coverage and improves longitudinal re- solution to scan the entire liver. This study was to evaluate the value of multiphase hepatic CT scans using MDCT in diagnosing hypervascular hepatocellular carcinoma (HCC). METHODS: Multiphase hepatic CT scans in 40 patients were carried out with a Marconi Mx8000 MDCT scanner. The scans of early arterial phase (EAP), late arterial phase (LAP) and portal venous phase (PVP) were started at 21, 34 and 85 seconds after injection of contrast medium, re- spectively. The number of detected lesions was calculated in each phase. The density of the liver and tumor was great- er than 1 cm for HCC, and the density of the liver and tumor in each phase was statistically calculated. RESULTS: A total of 61 lesions were found in the 40 pa- tients , and lesions greater than 1 cm were seen in 47 cases. The density differences between the liver and tumor were statistically significant (P<0.05) at the LAP and EAP and between the LAP, EAP and PVP. In the 61 lesions, the de- tectability in the EAP, LAP and the double arterial phases (DAP) was 32%, 87%, and 94%, respectively. Significant difference was found between the LAP plus PVP and the EAP plus PVP; but no significant difference was observed between the DAP plus PVP and the LAP plus PVP. CONCLUSIONS: The utility of MDCT scan in the liver has optimized the protocol of arterial phase scan. MDCT is possible to scan the entire liver in a real arterial phase and it is very valuable in the detection of small HCC.展开更多
基金financially supported by the National Key R&D Projects(No.2021YFB3702000)the Regional Company Projects in Ansteel Beijing Research Institute(No.2022BJB07GF&No.2022BJB-13GF)。
文摘Electromagnetic stirring is one of the widely applied techniques to modify the quality of casting billets.Different from conventional rotate stirring,the helical stirring is more professional in assisting multi-dimensional flow of molten metal and eliminating solidification defects.In this study,the single-winding helical stirring(SWHS)was introduced,offering advantages such as smaller volume and lower electromagnetic shielding compared to traditional helical stirring methods.Following a comprehensive numerical simulation,the stirring parameters of SWHS were adjusted to yoke inclination angle of 43°and frequency of 12 Hz.The higher electromagnetic force and flow velocity in drawing direction,as well as the lower temperature gradient induced by the SWHS,are positive factors for homogeneous solidification of billet.The experimental results on Al-8%Si alloy and 0.4%C-1.1%Mn steel demonstrate that compared to rotate stirring,the SWHS process can induce better billet quality and is more effective in accelerating the equiaxed expansion and reducing element segregation.The SWHS process can enhance the equiaxed ratio of the billet by 58.3%and reduce segregation degree of carbon element by 10.97%.Consequently,SWHS holds great promise as a potential approach for improving the quality of continuous casting billets.
基金supported by the National Natural Science Foundation of China (Grant Nos. 11975163 and 12175160)the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD)。
文摘Based on high magnetic field helicon experiment(HMHX), HELIC code was used to study the effect of different magnetic fields on the power deposition under parabolic distribution. This paper is divided into three parts: preliminary calculation, actual discharge experiment and calculation. The results of preliminary calculation show that a magnetic field that is too small or too large cannot produce a good power deposition effect. When the magnetic field strength is 1200 Gs,a better power deposition can be obtained. The actual discharge experiment illustrates that the change of the magnetic field will have a certain influence on the discharge phenomenon. Finally, the results of verification calculation successfully verify the accuracy of the results of preliminary simulation. The results show that in the actual discharge experiment, it can achieve the best deposition effect when the magnetic field is 1185 Gs.
文摘In this paper, the problem of finding exact solutions to the magnetohydrodynamic(MHD) equations in the presence of incompressible mass flows with helical symmetry is considered. For ideal flows, a similarity reduction method is used to obtain exact solutions for several MHD flows with nonlinear variable Mach number. For resistive flows parallel to a magnetic field, the governing equilibrium equation is derived. The MHD equilibrium state of a helically symmetric incompressible flow is governed by a second-order elliptic partial differential equation(PDE) for the helical magnetic flux function. Exact solutions for the latter equation are obtained. Also, the equilibrium equations of a gravitating plasma with incompressible flow are derived.
基金financially supported by the National Natural Science Foundation of China (Grant Nos.51890913 and 51879183)the China Harbour Engineering Company (Grant No.2018-ZJKJ-01)+2 种基金the China Scholarship Councilthe State Key Laboratory of Hydraulic Engineering Simulation and Safety,Tianjin University (Grant No.HESS-2019)the State Key Laboratory of Coastal and Offshore Engineering,Dalian University of Technology (Grant No.LP2120)。
文摘Helical anchor is a kind of novel foundation for floating offshore wind turbines,which should be subjected to combined tensile loading caused by wind,wave and current.However,the research about the capacity of helical anchor was mainly examined under uniaxial loading and scarcely explored under combined loading.In this study,three-dimensional finite element limit analysis is adopted to assess the bearing capacities of single-plate rigid helical anchors with different ratios of helix to shaft diameter,D_(H)/D_(S) and embedment ratios L/D_(S).Result shows that the vertical,horizontal and moment bearing capacities increase with increasing D_(H)/D_(S) and L/D_(S).The normalized V-H failure envelopes expands with increasing L/D_(S),while the normalized V-M failure envelopes tend to contract with the increase of D_(H)/D_(S).With increasing D_(H)/D_(S) or decreasing L/D_(S),the normalized H-M failure envelopes expand when the horizontal and moment loading act in the same direction and contract when they act in the opposite direction.The effect of D_(H)/D_(S) and L/D_(S) on the shape of H-M failure envelope become insignificant when L/D_(S)≥4.A series of failure mechanisms under different loading conditions were observed and can be used to explain the trend.Besides,a series of approximate expressions were proposed to fit the uniaxial bearing capacities and the failure envelopes.
文摘The aim of this study is the numerical analysis of the melting process of the phase change material(PCM)in a spiral coil.The space between the inner tube and outer shell is filled with RT-50 as PCM.Moreover,the hybrid nanofluid(with a carbon component)flows through the inner tube.The novelty of this work is to use different configurations of fin and different percentage of hybrid nanoparticles(SWCNTs-Cu O)on the PCM melting process.In the numerical model created by ANSYS-Fluent,the effect of various inlet temperatures is investigated.The results indicate that the extended surface created by extra fin has a dominant effect on melting time,so by adding the third fin,the melting time is reduced by 39.24%.The next most influential factor in PCM melting is the inlet temperature of the working fluid,so that 10°C increment of temperature result in the PCM melting time decreased by 35.41%.
文摘The goal of this research is to look at multi-target optimization of a two-stage helical gearbox in order to determine the best key design elements for reducing gearbox height and enhancing gearbox efficiency.To do this,the method known as Taguchi and GRA(Grey Relation Analysis)were used in two stages to address the problem.The single-objective optimization problem was addressed first to close the gap between variable levels,and then the multi-objective optimization problem was solved to determine the best primary design variables.The first and second stage CWFWs(Coefficients of Wheel Face Width),ACS(Permissible Contact Stresses),and first stage gear ratio were also calculated.The study’s findings were utilized to identify the best values for five critical design aspects of a two-stage helical gearbox.
基金This work was supported by the National Natural Science Foundation of China (Grant Nos. 40475024 and 40333025), the foundation for Ph.D specialty of the Ministry of Education (Grant No. 20020284016).
文摘Helicity is defined as H : V ω, where V and ω are the velocity and vorticity vectors, respectively. Many works have pointed out that the larger the helicity is, the longer the life cycle of the weather system is. However, the direct relationship of the helicity to the evolution of the weather system is not quite clear. In this paper, the concept of helicity is generalized as shearing wind helicity (SWH). Dynamically, it is found that the average SWH is directly related to the increase of the average cyclonic rotation of the weather system. Physically, it is also pointed out that the SWH, as a matter of fact, is the sum of the torsion terms and the divergence term in the vorticity equation. Thermal wind helicity (TWH), as a derivative of SWH, is also discussed here because it links the temperature field and the vertical wind field. These two quantities may be effective for diagnosing a weather system. This paper applies these two quantities in cylindrical coordinates to study the development of Hurricane Andrew to validate their practical use. Through analyzing the hurricane, it is found that TWH can well describe the characteristics of the hurricane such as the strong convection and release of latent heat. SWH is not only a good quantity for diagnosing the weather system, but also an effective one for diagnosing the development of the hurricane.
基金sponsored by the National Natural Science Foundation of China under Grant No.400750112001 PIA 20026 the National Key program for Developing Basic Sciences:CHeRES(G 1998040907).
文摘The characteristics of helicity in a hurricane are presented by calculating the MM5 model output in addition to theoretical analysis. It is found that helicity in a hurricane mainly depends on its horizontal component, whose magnitude is about 100 to 1000 times larger than its vertical component. It is also found that helicity is approximately conserved in the hurricane. Since the fluid has the intention to adjust the wind shear to satisfy the conservation of helicity, the horizontal vorticity is even larger than the vertical vorticity, and the three-dimensional vortices slant to the horizontal plane except in the inner eye. There are significant horizontal vortices and inhomogeneous helical flows in the hurricane. The formation of the spiral rainband is discussed by using the law of horizontal helical flows. It is closely related to the horizontal strong vortices and inhomogeneous helical flows.
基金supported by the National Natural Science Foundation of China (30871749,30901004)Natural Science Foundation of Fujian Province(2009J01061)
文摘In this work, the formation sites, helical parameters and hydrogen bond positions of Konjac glucomannan molecular helices were investigated using molecular dynamic simulation method. To our interest, the KGM chain is mainly composed by local left and right helix struetttres. The formation sites of KGM chain might locate at the chain-segments containing acetyl groups, and the left helix is the favorable conformation of KGM. Temperature-dependent molecule conformation study indicates that the right helix is dominant when the temperature is lower than 343 K, above which, however, the left helix is dominating (right helix disappears). In addition, intramolecular hydrogen bonds in the left helix can be found at the -OH groups on C(2), C(4) and C(6) of mannose residues; comparably, the intramolecular hydrogen bonds in the right helix can be mainly observed at the -OH groups on C(4) and C(6) of the mannose residues and C(3) of the glucose residues. In conclusion, molecular dynamic simulation is an efficient method for the microscopic conformation study of glucomannan molecular helices.
基金supported by NSFC(91330116)NSFC(11371289)+1 种基金NSFC(11371288)State Major Basic Research and Development Project(2011CB 706505)
文摘In this article, we investigate three-dimensional solution with helical symmetry in a gap between two concentric rotating cylinders, inside is a helicoidal surface(screw propeller)while outside is a cylindrical surface. Establish the partial differential equations and its variational formulation satisfied by a helical solution in a helical coordinate system using tensor analysis method, we provide a computational method for the power and propulsion of the screw. The existence and uniqueness of weak helical solutions are proved.
基金financially supported by the National Natural Science Foundation of China(Grant No.51176129)the Innovation Key Program of Shanghai Municipal Education Commission(Grant No.13YZ066)the Doctoral Fund of the Ministry of Education of China(Grant No.20123120110008)
文摘The stability of platform structure is the paramount guarantee of the safe operation of the offshore floating wind turbine. The NREL 5MW floating wind turbine is established based on the OC3-Hywind Spar Buoy platform with the supplement of helical strakes for the purpose to analyze the impact of helical strakes on the dynamic response of the floating wind turbine Spar platform. The dynamic response of floating wind turbine Spar platform under wind, wave and current loading from the impact of number, height and pitch ratio of the helical strakes is analysed by the radiation and diffraction theory, the finite element method and orthogonal design method. The result reveals that the helical strakes can effectively inhibit the dynamic response of the platform but enlarge the wave exciting force; the best parameter combination is two pieces of helical strakes with the height of 15%D (D is the diameter of the platform) and the pitch ratio of 5; the height of the helical strake and its pitch ratio have significant influence on pitch response.
基金Supported by the National Natural Science Foundation of China(51776035).
文摘The shell side flow fields of both sextant and trisection helical baffle heat exchangers are presented on meridian and multilayer hexagon slices.It verifies that the performance of sextant schemes is better than those of the other kinds of helical baffle heat exchangers.The main mechanisms are due to the restricted leakage flow in the minimized gaps with increased baffle number and by one row of tubes dampen the leakage flow in the circumferential overlapped area of the adjacent helical baffles.The performance features were simulated on two different angled sextant helical heat exchangers and each compared with two trisection ones of either identical helical pitch or identical incline angle.The results verified that the performances of helical heat exchangers are mainly determined by the helical pitch rather than the baffle incline angle.The average values of comprehensive index hoΔpo-1/3 of the trisection helical schemes T-24.1°and T-29.7°are correspondingly 3.47%and 3.34%lower than those of the sextant ones X-20°and X-25°with identical helical pitches.The comparison results show that the average values of shell side h.t.c.hoand comprehensive index hoΔpo-1/3 of the optimal dual helix sextant scheme DX30°are respectively 7.22%and 23.56%higher than those of the segment scheme S100.
文摘Objective: To evaluate the short-term clinical outcomes of intracranial germinoma patients treated with craniospinal irradiation (CSI) using helical tomotherapy (HT) system in our center. Methods: Twenty-three patients who were treated with CSI in our center from January 2008 to July 2012 were collected, with an average age of 20. M1 of the patients' CSI used the HT system. The total doses were 27-36 Gy/15-20 F (1.5-2 Gy per fraction), and total local doses were 46-60 Gy/30-50 F (5 fractions per week). M1 female patients for CSI were treated with left-right parallel-opposed field irradiation to protect their ovarian functions. Median follow-up time was 30.9 months (range, 5-67 months). The SPSS19.0 software was used, and the overall survival (OS) was calculated using the Kaplan-Meier method. Results: Among 17 patients with assessable tumors, 9 cases (52.9%) were CR, 7 cases (41.2%) were PR, and 1 case (5.9%) was SD. Hematological toxicity was the severest side-effect occurred in the procedure of CSI. The level 1-4 acute leukopenia were 8.7%, 30.4%, 34.8% and 21.7% and the level 1-4 acute thrombopenia were 8.7%, 30.4%, 21.7% and 8.7%, respectively. Conclusions: For primary intracranial germinomas, HT can be used to implement CSI for simplifying radiotherapy procedures, improving radiotherapy accuracy, enhancing protection of peripheral organs at risk (ORA) and guaranteeing therapeutic effects. With the acceptable acute and long-term toxicity, CSI using HT in intracranial germinoma patients can be a safe and alternative mode.
基金supported by the National Natural Science Foundation of China(Grant Nos.51479135,51525803 and 51679167)the Science Fund for Creative Research Groups of the National Natural Science Foundation of China(Grant No.51621092)+1 种基金the Major State Basic Research Development Program of China(973 Program,Grant No.2014CB046801)the Natural Science Foundation of Tianjin(Grant No.15JCQNJC07700)
文摘An experimental study on a bare flexible cylinder as well as cylinders fitted with two types of cross-sectioned helical strakes was carried out in a towing tank. The main purpose of this paper is to investigate the effects of strakes’ cross-section on the vortex-induced vibrations (VIV) suppression of a flexible cylinder. The square-sectioned and round-sectioned helical strakes were selected in the experimental tests. The uniform current was generated by towing the cylinder models along the tank using a towing carriage. The Reynolds number was in the range of 800–16000. The strain responses were measured by the strain gages in cross-flow (CF) and in-line (IL) directions. A modal analysis method was adopted to obtain the displacement responses using the strain signals in different measurement positions. The comparison of the experimental results among the bare cylinder, square-sectioned straked cylinder and round-sectioned straked cylinder was performed. The helical strakes can effectively reduce the strain amplitude, displacement amplitude, response frequencies and dominant modes of a flexible cylinder excited by VIV. And the mean drag coefficients of straked cylinders were approximately consistent with each other. In addition, the square-sectioned and round-sectioned strakes nearly share the similar VIV reduction behaviors. Sometimes, the strakes with round-section represent more excellent effects on the VIV suppression of response frequency than those with square-section.
基金supported by National Natural Science Foundation for Distinguished Young Scholar of China (Grant No. 50925518)National Natural Science Foundation of China (Grant No. 50775226)+1 种基金Key Project of Ministry of Education of China(Grant No. 109129)Chongqing Municipal Key Scientific and Technological Project of China (Grant No. CSTC2009AC3049)
文摘A stranded wires helical spring is formed of a multilayer and coaxial strand of several wires twisted together with the same direction of spiral. Compared with the conventional single wire spring, the stranded wires helical spring has the notable predominance in strength, damping and vibration reduction, which is usually used in aircraft engines, automatic weapons, etc. However, due to its complicated structure, the precise computation of its strength and rigidity need be a correct mathematical model, which then will be imported to finite element analysis software for solutions. Equations on solving geometric parameters, such as external diameters of strands and screw pitches of wires, are put forward in the paper. It also proposes a novel methodology on solving geometric parameters and establishing entity models of the stranded wires helical spring, which provides foundation of computing mechanical parameters by FEA. Then mathematical models on the centre line of the strand and the surface curve of each wire, after closing two ends in a spring, are proposed. Finally, geometric parameters are solved in a case study, and a 3D entity model of a spring with 3 layers and 16 wires is established, which has validated the accuracy of the proposed methodology and the 3D entity mathematical model. The method provides a new way to design stranded wire helical spring.
基金supported by the National Natural Science Foundation of China (30871749, 30901004) the Natural Science Foundation of Fujian Province (2009J01061)
文摘The formation mechanism and stability of konjac glucomannan (KGM) helical structure were investigated by molecular dynamic simulation and experimental method. The results indicate that the molecular conformation of KGM is a non-typical helical structure. In detail, helical structure of KGM is mainly sustained by acetyl group, whose size and stability are affected by the molecular polymerization degree of KGM. In vacuum among the non-bonding interactions, electrostatic force is the greatest factor affecting its helical structure, but in water solution, hydrogen bond affects the helical arrangement greatly. To our interest, temperature exhibits a reversible destroying effect to some extent; the helical structure will disappear completely and present a ruleless clew-like arrangement till 341 K. This work suggests that the method of combining molecular dynamic simulation and experiment tools can be effective in the study of KGM helical structure.
文摘BACKGROUND: Multirow-detector helical CT (MDCT) allows faster Z-axis coverage and improves longitudinal re- solution to scan the entire liver. This study was to evaluate the value of multiphase hepatic CT scans using MDCT in diagnosing hypervascular hepatocellular carcinoma (HCC). METHODS: Multiphase hepatic CT scans in 40 patients were carried out with a Marconi Mx8000 MDCT scanner. The scans of early arterial phase (EAP), late arterial phase (LAP) and portal venous phase (PVP) were started at 21, 34 and 85 seconds after injection of contrast medium, re- spectively. The number of detected lesions was calculated in each phase. The density of the liver and tumor was great- er than 1 cm for HCC, and the density of the liver and tumor in each phase was statistically calculated. RESULTS: A total of 61 lesions were found in the 40 pa- tients , and lesions greater than 1 cm were seen in 47 cases. The density differences between the liver and tumor were statistically significant (P<0.05) at the LAP and EAP and between the LAP, EAP and PVP. In the 61 lesions, the de- tectability in the EAP, LAP and the double arterial phases (DAP) was 32%, 87%, and 94%, respectively. Significant difference was found between the LAP plus PVP and the EAP plus PVP; but no significant difference was observed between the DAP plus PVP and the LAP plus PVP. CONCLUSIONS: The utility of MDCT scan in the liver has optimized the protocol of arterial phase scan. MDCT is possible to scan the entire liver in a real arterial phase and it is very valuable in the detection of small HCC.