The heat treatment process has great effects on microstructure and conductivity of ingots. In this study, the ingots of high strength 7075 aluminum alloy were prepared by low frequency electromagnetic casting(LFEC), a...The heat treatment process has great effects on microstructure and conductivity of ingots. In this study, the ingots of high strength 7075 aluminum alloy were prepared by low frequency electromagnetic casting(LFEC), and the effect of different homogenization processes(single-step homogenization at 465 ℃ for different holding times and three-step homogenization) on the microstructure and conductivity of 7075 aluminum alloy were studied by means of metallographic microscopy, electrical conductivity test, differential thermal analysis and X-ray diffraction phase analysis. For comparison, the ingot by conventional direct casting(DC) under the same conditions was also prepared. Results show that the non-equilibrium eutectic phases with low melting point in the ingot dissolve continuously into the matrix as the holding time of single-step homogenization increases. The endothermic peak of non-equilibrium phases can not be completely eliminated through a 24 h single-step homogenization, but can be eliminated after a three-step homogenization(200 ℃/2 h + 460 ℃/6 h + 480 ℃/12 h). Meanwhile, the homogenization has a better effect on the LFEC ingot than the conventional DC ingot. Under the same homogenizing conditions, the grains of LFEC ingot are characterized by a lower content of low melting point phases and the ingot shows higher electrical conductivity than DC ingot.展开更多
目的:研究短梗五加果多酚(Acanthopanax sessiliflorus fruit polyphenols,ASFP)对大鼠动脉粥样硬化(atherosclerosis,As)的预防作用,并探讨其作用机制。方法:40只雄性SD大鼠随机平均分成4组,每组10只。采用高脂饮食结合腹腔注射VD3的...目的:研究短梗五加果多酚(Acanthopanax sessiliflorus fruit polyphenols,ASFP)对大鼠动脉粥样硬化(atherosclerosis,As)的预防作用,并探讨其作用机制。方法:40只雄性SD大鼠随机平均分成4组,每组10只。采用高脂饮食结合腹腔注射VD3的方法建立As模型,不同剂量ASFP给药组自造模开始之日起分别灌胃150、75 mg/(kg·d)的ASFP,空白组和高脂饮食组大鼠灌胃等量生理盐水,各实验组连续处理12周后,检测大鼠血清生理生化水平并计算As指数;苏木素-伊红染色观察大鼠主动脉As病变情况;Western blot检测主动脉中黏附分子和丝裂原活化蛋白激酶(mitogen-activated protein kinase,MAPK)信号通路关键基因的蛋白表达水平。结果:与高脂饮食组相比,ASFP能显著降低大鼠血清中的血脂、黏附分子和炎症因子水平,减少主动脉中的脂质沉积,改善各层结构排列紊乱,显著降低主动脉中细胞间黏附分子-1、血管细胞黏附分子-1、磷酸化p38和磷酸化细胞外信号调节蛋白激酶1/2(phospho-extracellular signal regulated kinases 1/2,p-ERK1/2)的蛋白表达量。结论:ASFP具有预防As的作用,其作用可能与其降血脂和抑制p38 MAPK和ERK1/2 MAPK信号通路,进而抑制炎症因子的表达有关。展开更多
A ladle-tundish-mould transportation model considering the entire multiple pouring(MP) process is proposed. Numerical simulation is carried out to study the carbon distribution and variation in both the tundish and th...A ladle-tundish-mould transportation model considering the entire multiple pouring(MP) process is proposed. Numerical simulation is carried out to study the carbon distribution and variation in both the tundish and the mould for making a 292 t steel ingot. Firstly, the fluid flow as well as the heat and mass transfer of the molten steel in the tundish is simulated based on the multiphase transient turbulence model. Then, the carbon mixing in the mould is calculated by using the species concentration at the tundish outlet as the inlet condition during the teeming process. The results show a high concentration of carbon at the bottom and a low concentration of carbon at the top of the mould after a MP process with carbon content high in the first ladle and low in the last ladle. Such carbon concentration distribution would help reduce the negative segregation at the bottom and the positive segregation at the top of the solidified ingot.展开更多
Porous aluminum alloys produced by the metal-gas eutectic method or GASAR process need to be performed under a certain pressure of hydrogen, and to carry over melt to a tailor-made apparatus that ensures directional s...Porous aluminum alloys produced by the metal-gas eutectic method or GASAR process need to be performed under a certain pressure of hydrogen, and to carry over melt to a tailor-made apparatus that ensures directional solidif ication. Hydrogen is driven out of the melt, and then the quasi-cylindrical pores normal to the solidif ication front are usually formed. In the research, the effects of processing parameters(saturation pressure, solidif ication pressure, temperature, and holding time) on the pore structure and porosity of porous aluminum alloys were analyzed. The mechanical properties of Al-Mg alloys were studied by the compressive tests, and the advantages of the porous structure were indicated. By using the GASAR method, pure aluminum, Al-3wt.%Mg, Al-6wt.%Mg and Al-35wt.%Mg alloys with oriented pores have been successfully produced under processing conditions of varying gas pressure, and the relationship between the f inal pore structure and the solidif ication pressure, as well as the inf luences of Mg quantity on the pore size, porosity and mechanical properties of AlMg alloy were investigated. The results show that a higher pressure of solidif ication tends to yield smaller pores in aluminum and its alloys. In the case of Al-Mg alloys, it was proved that with the increasing of Mg amount, the mechanical properties of the alloys sharply deteriorate. However, since Al-3%Mg and Al-6wt.%Mg alloys are ductile metals, their porous samples have greater compressive strength than that of the dense samples due to the existence of pores. It gives the opportunity to use them in industry at the same conditions as dense alloys with savings in weight and material consumption.展开更多
本文全面对比分析了单向纤维增强聚合物基复合材料Ⅰ型层间断裂韧性的标准试验方法国标GB/T 28891-2012和美标ASTM D 5528-01(07)的主要异同点,并对相关规定进行了对比分析。结果表明:国标与美标在环境条件、试样状态调节、试样尺寸要...本文全面对比分析了单向纤维增强聚合物基复合材料Ⅰ型层间断裂韧性的标准试验方法国标GB/T 28891-2012和美标ASTM D 5528-01(07)的主要异同点,并对相关规定进行了对比分析。结果表明:国标与美标在环境条件、试样状态调节、试样尺寸要求、试验方法、试验报告等方面有一些区别,二者可相互借鉴完善,并结合更多新材料测试的需求不断更新,考虑复杂试验环境和特殊情况,从而制定更适合我国航空航天工业及高端制造业的单向纤维增强聚合物基复合材料Ⅰ型层间断裂韧性的标准试验方法标准。展开更多
基金financially supported by the National Natural Science Foundation of China(youth)(No.51004036)the Fundamental Research Funds(N120309002)
文摘The heat treatment process has great effects on microstructure and conductivity of ingots. In this study, the ingots of high strength 7075 aluminum alloy were prepared by low frequency electromagnetic casting(LFEC), and the effect of different homogenization processes(single-step homogenization at 465 ℃ for different holding times and three-step homogenization) on the microstructure and conductivity of 7075 aluminum alloy were studied by means of metallographic microscopy, electrical conductivity test, differential thermal analysis and X-ray diffraction phase analysis. For comparison, the ingot by conventional direct casting(DC) under the same conditions was also prepared. Results show that the non-equilibrium eutectic phases with low melting point in the ingot dissolve continuously into the matrix as the holding time of single-step homogenization increases. The endothermic peak of non-equilibrium phases can not be completely eliminated through a 24 h single-step homogenization, but can be eliminated after a three-step homogenization(200 ℃/2 h + 460 ℃/6 h + 480 ℃/12 h). Meanwhile, the homogenization has a better effect on the LFEC ingot than the conventional DC ingot. Under the same homogenizing conditions, the grains of LFEC ingot are characterized by a lower content of low melting point phases and the ingot shows higher electrical conductivity than DC ingot.
文摘目的:研究短梗五加果多酚(Acanthopanax sessiliflorus fruit polyphenols,ASFP)对大鼠动脉粥样硬化(atherosclerosis,As)的预防作用,并探讨其作用机制。方法:40只雄性SD大鼠随机平均分成4组,每组10只。采用高脂饮食结合腹腔注射VD3的方法建立As模型,不同剂量ASFP给药组自造模开始之日起分别灌胃150、75 mg/(kg·d)的ASFP,空白组和高脂饮食组大鼠灌胃等量生理盐水,各实验组连续处理12周后,检测大鼠血清生理生化水平并计算As指数;苏木素-伊红染色观察大鼠主动脉As病变情况;Western blot检测主动脉中黏附分子和丝裂原活化蛋白激酶(mitogen-activated protein kinase,MAPK)信号通路关键基因的蛋白表达水平。结果:与高脂饮食组相比,ASFP能显著降低大鼠血清中的血脂、黏附分子和炎症因子水平,减少主动脉中的脂质沉积,改善各层结构排列紊乱,显著降低主动脉中细胞间黏附分子-1、血管细胞黏附分子-1、磷酸化p38和磷酸化细胞外信号调节蛋白激酶1/2(phospho-extracellular signal regulated kinases 1/2,p-ERK1/2)的蛋白表达量。结论:ASFP具有预防As的作用,其作用可能与其降血脂和抑制p38 MAPK和ERK1/2 MAPK信号通路,进而抑制炎症因子的表达有关。
基金financially supported by the National Basic Research Program of China(No.2011CB012900)the National Science and Technology Major Project of the Ministry of Science and Technology of China(No.2012ZX04012011)
文摘A ladle-tundish-mould transportation model considering the entire multiple pouring(MP) process is proposed. Numerical simulation is carried out to study the carbon distribution and variation in both the tundish and the mould for making a 292 t steel ingot. Firstly, the fluid flow as well as the heat and mass transfer of the molten steel in the tundish is simulated based on the multiphase transient turbulence model. Then, the carbon mixing in the mould is calculated by using the species concentration at the tundish outlet as the inlet condition during the teeming process. The results show a high concentration of carbon at the bottom and a low concentration of carbon at the top of the mould after a MP process with carbon content high in the first ladle and low in the last ladle. Such carbon concentration distribution would help reduce the negative segregation at the bottom and the positive segregation at the top of the solidified ingot.
基金financially supported by Liaoning BaiQianWan Talents Program(No.2011921065)
文摘Porous aluminum alloys produced by the metal-gas eutectic method or GASAR process need to be performed under a certain pressure of hydrogen, and to carry over melt to a tailor-made apparatus that ensures directional solidif ication. Hydrogen is driven out of the melt, and then the quasi-cylindrical pores normal to the solidif ication front are usually formed. In the research, the effects of processing parameters(saturation pressure, solidif ication pressure, temperature, and holding time) on the pore structure and porosity of porous aluminum alloys were analyzed. The mechanical properties of Al-Mg alloys were studied by the compressive tests, and the advantages of the porous structure were indicated. By using the GASAR method, pure aluminum, Al-3wt.%Mg, Al-6wt.%Mg and Al-35wt.%Mg alloys with oriented pores have been successfully produced under processing conditions of varying gas pressure, and the relationship between the f inal pore structure and the solidif ication pressure, as well as the inf luences of Mg quantity on the pore size, porosity and mechanical properties of AlMg alloy were investigated. The results show that a higher pressure of solidif ication tends to yield smaller pores in aluminum and its alloys. In the case of Al-Mg alloys, it was proved that with the increasing of Mg amount, the mechanical properties of the alloys sharply deteriorate. However, since Al-3%Mg and Al-6wt.%Mg alloys are ductile metals, their porous samples have greater compressive strength than that of the dense samples due to the existence of pores. It gives the opportunity to use them in industry at the same conditions as dense alloys with savings in weight and material consumption.
文摘本文全面对比分析了单向纤维增强聚合物基复合材料Ⅰ型层间断裂韧性的标准试验方法国标GB/T 28891-2012和美标ASTM D 5528-01(07)的主要异同点,并对相关规定进行了对比分析。结果表明:国标与美标在环境条件、试样状态调节、试样尺寸要求、试验方法、试验报告等方面有一些区别,二者可相互借鉴完善,并结合更多新材料测试的需求不断更新,考虑复杂试验环境和特殊情况,从而制定更适合我国航空航天工业及高端制造业的单向纤维增强聚合物基复合材料Ⅰ型层间断裂韧性的标准试验方法标准。
