Electron beam welding of Ti-15-3 alloy to 304 stainless steel （STS） using a copper filler metal was carried out. The temperature fields and stress distributions in the Ti/Fe and Ti/Cu/Fe joint during the welding pro...Electron beam welding of Ti-15-3 alloy to 304 stainless steel （STS） using a copper filler metal was carried out. The temperature fields and stress distributions in the Ti/Fe and Ti/Cu/Fe joint during the welding process were numerically simulated and experimentally measured. The results show that the rotated parabola body heat source is fit for the simulation of the electron beam welding. The temperature distribution is asymmetric along the weld center and the temperature in the titanium alloy plate is higher than that in the 304 STS plate. The thermal stress also appears to be in asymmetric distribution. The residual tensile stress mainly exists in the weld at the 304 STS side. The copper filler metal decreases the peak temperature and temperature grade in the joint as well as the residual stress. The longitudinal and lateral residual tensile strengths reduce by 66 MPa and 31 MPa, respectively. From the temperature and residual stress, it is concluded that copper is a good filler metal candidate for the electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel.展开更多
Wrinkling is a common failure in the sheet metal forming of titanium owing to the relatively poor ability to shrink. It is important to predict wrinkling accurately in the sheet metal forming without costly trials. Th...Wrinkling is a common failure in the sheet metal forming of titanium owing to the relatively poor ability to shrink. It is important to predict wrinkling accurately in the sheet metal forming without costly trials. The ABAQUS/Explicit code was utilized to predict the wrinkling behavior in the sheet metal forming of Ti-15-3 alloy sheets. In terms of the comparison of wrinkling behavior between the simulation and experiment of the Fukui＇s conical cup tests at room temperature, the sensitivities of wrinkling simulation to various input parameters were evaluated comprehensively and quantitatively. Prediction of wrinkling and influence of rubber hardness on the winkling behavior in the rubber forming of convex flange were investigated quantitatively and validated by the rubber forming experiments. The excellent agreements between the simulations and the experiments conIirmed the accuracy of the prediction.展开更多
The forming limit diagram of Ti-15-3 alloy sheet was constituted at room temperature. The effects of different punch and rubber hardness on the limit principal strain distributions were investigated experimentally. Fi...The forming limit diagram of Ti-15-3 alloy sheet was constituted at room temperature. The effects of different punch and rubber hardness on the limit principal strain distributions were investigated experimentally. Finite element analysis models of the samples with dimensions of 180 mm×180 mm were established to analyze the friction coefficients of different interfaces. Effects of various friction coefficients on the strain distributions were studied in detail. Finally, the friction coefficients in the cold forming were determined by contrasting the strain results between the experimental data and the simulated ones.展开更多
Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with a copper sheet as interlayer was carried out.Microstructures of the joint were studied by optical microscopy(OM),scanning electron microscopy...Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with a copper sheet as interlayer was carried out.Microstructures of the joint were studied by optical microscopy(OM),scanning electron microscopy(SEM) and X-ray diffractometry(XRD).In addition,the mechanical properties of the joint were evaluated by tensile test and the microhardness was measured.These two alloys were successfully welded by adding copper transition layer into the weld.Solid solution with a certain thickness was located at the interfaces between weld and base metal in both sides.Regions inside the weld and near the stainless steel were characterized by solid solution of copper with TiFe2 intermetallics dispersedly distributed in it.While weld near titanium alloy contained Ti-Cu and Ti-Fe-Cu intermetallics layer,in which the hardness of weld came to the highest value.Brittle fracture occurred in the intermetallics layer when the joint was stretched.展开更多
Ti-15-3 alloy is a new metastableβ-type titanium. The influence of hot deformation parameters on the microstructureof Ti-15-3 alloy after solution treatment has been studied by isothermal compression tests as well as...Ti-15-3 alloy is a new metastableβ-type titanium. The influence of hot deformation parameters on the microstructureof Ti-15-3 alloy after solution treatment has been studied by isothermal compression tests as well as quantitativemetallographic analysis. On the basis of the data obtained from the tests, predicting models for equivalent grainsize and recrystallization volume fraction have been established with an artificial neural network method. An FEnumerical simulation system has been developed to simulate the distribution of microstructure in Ti-15-3 alloy afterhot back extrusion and solution treatment by combining the neural network model with thermal-mechanical coupledrigid-viscoplastic FE model. Corresponding experimental research is performed. The agreement of the simulatedresults with measured ones shows that the simulation system is reliable.展开更多
Hot compression experiments were conducted on Ti 15 3 alloy specimens using Gleeble 1500 Thermal Simulator.These tests were focused to obtain the flow stress data under various conditions of strain,strain rate and tem...Hot compression experiments were conducted on Ti 15 3 alloy specimens using Gleeble 1500 Thermal Simulator.These tests were focused to obtain the flow stress data under various conditions of strain,strain rate and temperature. On the basis of these data, the predicting model for the nonlinear relation between flow stress and deformation strain,strain rate and temperature for Ti 15 3 alloy was developed with a back propagation artificial neural network method. Results show that the neural network can reproduce the flow stress in the sampled data and predict the nonsampled data well. Thus the neural network method has been verified to be used to tackle hot deformation problems of Ti 15 3 alloy. [展开更多
The key problems of cold power spinning of Ti-15-3 alloy are studied. Reasonable billet preparation methods are presented to improve crystal structure and avoid crack of billet. Influences of original wall thickness,...The key problems of cold power spinning of Ti-15-3 alloy are studied. Reasonable billet preparation methods are presented to improve crystal structure and avoid crack of billet. Influences of original wall thickness, reduction rate and feed rate on expanding in diameter are analyzed and some methods to prevent expanding in diameter are given.展开更多
Grain shape of the hot deforming alloy is an important of material. The fractal theory was applied to analyze index to character the microstructure and performance the recrystallized microstructure of Ti-15-3 alloy af...Grain shape of the hot deforming alloy is an important of material. The fractal theory was applied to analyze index to character the microstructure and performance the recrystallized microstructure of Ti-15-3 alloy after hot deformation and solution treatment. The fractal dimensions of recrystallized grains were calculated by slit island method. The influence of processing parameters on fractal dimension and grain size was studied, It has been shown that the shapes of recrystallized grain boundaries are self-similar, and the fractal dimension varies from 1 to 2. With increasing deformation degree and strain rate or decreasing deformation temperature, the fractal dimension of grain boundaries increased and the grain size decreased. So the fractal dimension could characterize the grain shape and size. A neural network model was trained to predict the fractal dimension of recrystallized microstructure and the result is in excellent agreement with the experimental data.展开更多
目的合成环己酮3-氯-1,2-丙二醇缩酮。方法采用浸渍法制备了H6P2W18O62/TiO2-SiO2催化剂,并采用FT-IR、XRD、SEM对其进行了表征。以环己酮和3-氯-1,2-丙二醇为原料,催化合成环己酮3-氯-1,2-丙二醇缩酮,采用FT-IR、1 H NMR、13 C NMR等...目的合成环己酮3-氯-1,2-丙二醇缩酮。方法采用浸渍法制备了H6P2W18O62/TiO2-SiO2催化剂,并采用FT-IR、XRD、SEM对其进行了表征。以环己酮和3-氯-1,2-丙二醇为原料,催化合成环己酮3-氯-1,2-丙二醇缩酮,采用FT-IR、1 H NMR、13 C NMR等表征手段来分析合成产物为环己酮3-氯-1,2-丙二醇缩酮。结果在酮醇摩尔比为1∶1.4,带水剂环己烷用量8mL,催化剂用量为反应物总质量的2.0%,反应时间1.0h的条件下,缩酮收率可达85.0%。催化剂重复使用5次后收率有72.6%。结论 H6P2W18O62/TiO2-SiO2催化剂对合成环己酮3-氯-1,2-丙二醇缩酮不仅反应时间短,催化剂用量少,而且产品收率高。展开更多
Based on Kohler’s ternary solution model and Miedemaa’s model for calculating the heats of formation-△Hij of binary Systems, the integral equation has ben established for calculating the activity coefficients in te...Based on Kohler’s ternary solution model and Miedemaa’s model for calculating the heats of formation-△Hij of binary Systems, the integral equation has ben established for calculating the activity coefficients in ternarysolution. With the equation, the activity coefficients in Ti-15-3 melt have been calculated. The results show that allof components’ activity coefficients are less than 1, in other wolds, compared with ideal solution, all components takeon a negative deviation. At 2000K, the activity coefficients in Ti-15-3 melt are shown as: about 0.9 for Ti, about0.85 for V, about 0. 1 for Al, aboaut 0.5 for Cr and about 0.23 for Sn. me addition of V lowers the activity coefficient of Ti, but raise the ones of Al, Cr and Sn. These results can be directly used to calculate the evaporation loss ofAl, Cr and Sn during the ISM(Induction Skull Melting) process and at the same time estimate the reactivity betweenTi-15-3 melt and refractory during the cast production.展开更多
As concepts closely related to microwave absorption properties,impedance matching and phase matching were rarely combined with material parameters to regulate properties and explore related mechanisms.In this work,red...As concepts closely related to microwave absorption properties,impedance matching and phase matching were rarely combined with material parameters to regulate properties and explore related mechanisms.In this work,reduction–diffusion method was innovatively applied to synthesize rare earth alloy Y_(2)Fe_(17).In order to regulate the electromagnetic parameters of absorbers,the Y_(2)Fe_(17)N_(3-δ)particles were coated with silica(Y_(2)Fe_(17)N_(3-δ)@SiO_(2))and absorbers with different volume fractions were prepared.The relationship between impedance matching,matching thickness,and the strongest reflection loss peak(RLmin)was presented obviously.Compared to the microwave absorption properties of Y_(2)Fe_(17)N_(3-δ)/PU absorber,Y_(2)Fe_(17)N_(3-δ)@SiO_(2)/PU absorbers are more conducive to the realization of microwave absorption material standards which are thin thickness,light weight,strong absorbing intensity,and broad bandwidth.Based on microwave frequency bands,the microwave absorption properties of the absorbers were analyzed and the related parameters were listed.As an important parameter related to perfect matching,reflection factor(√ε_(r)/μ_(r))was discussed combined with microwave amplitude attenuation.According to the origin and mathematical model of bandwidth,the formula of EAB(RL<-10 dB)was derived and simplified.The calculated bandwidths agreed well with experimental results.展开更多
基金Foundation item:Project (2010CB731704) supported by the National Basic Research Program of ChinaProject (51075189) supported by the National Natural Science Foundation of China
文摘Electron beam welding of Ti-15-3 alloy to 304 stainless steel （STS） using a copper filler metal was carried out. The temperature fields and stress distributions in the Ti/Fe and Ti/Cu/Fe joint during the welding process were numerically simulated and experimentally measured. The results show that the rotated parabola body heat source is fit for the simulation of the electron beam welding. The temperature distribution is asymmetric along the weld center and the temperature in the titanium alloy plate is higher than that in the 304 STS plate. The thermal stress also appears to be in asymmetric distribution. The residual tensile stress mainly exists in the weld at the 304 STS side. The copper filler metal decreases the peak temperature and temperature grade in the joint as well as the residual stress. The longitudinal and lateral residual tensile strengths reduce by 66 MPa and 31 MPa, respectively. From the temperature and residual stress, it is concluded that copper is a good filler metal candidate for the electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel.
文摘Wrinkling is a common failure in the sheet metal forming of titanium owing to the relatively poor ability to shrink. It is important to predict wrinkling accurately in the sheet metal forming without costly trials. The ABAQUS/Explicit code was utilized to predict the wrinkling behavior in the sheet metal forming of Ti-15-3 alloy sheets. In terms of the comparison of wrinkling behavior between the simulation and experiment of the Fukui＇s conical cup tests at room temperature, the sensitivities of wrinkling simulation to various input parameters were evaluated comprehensively and quantitatively. Prediction of wrinkling and influence of rubber hardness on the winkling behavior in the rubber forming of convex flange were investigated quantitatively and validated by the rubber forming experiments. The excellent agreements between the simulations and the experiments conIirmed the accuracy of the prediction.
文摘The forming limit diagram of Ti-15-3 alloy sheet was constituted at room temperature. The effects of different punch and rubber hardness on the limit principal strain distributions were investigated experimentally. Finite element analysis models of the samples with dimensions of 180 mm×180 mm were established to analyze the friction coefficients of different interfaces. Effects of various friction coefficients on the strain distributions were studied in detail. Finally, the friction coefficients in the cold forming were determined by contrasting the strain results between the experimental data and the simulated ones.
文摘Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with a copper sheet as interlayer was carried out.Microstructures of the joint were studied by optical microscopy(OM),scanning electron microscopy(SEM) and X-ray diffractometry(XRD).In addition,the mechanical properties of the joint were evaluated by tensile test and the microhardness was measured.These two alloys were successfully welded by adding copper transition layer into the weld.Solid solution with a certain thickness was located at the interfaces between weld and base metal in both sides.Regions inside the weld and near the stainless steel were characterized by solid solution of copper with TiFe2 intermetallics dispersedly distributed in it.While weld near titanium alloy contained Ti-Cu and Ti-Fe-Cu intermetallics layer,in which the hardness of weld came to the highest value.Brittle fracture occurred in the intermetallics layer when the joint was stretched.
文摘Ti-15-3 alloy is a new metastableβ-type titanium. The influence of hot deformation parameters on the microstructureof Ti-15-3 alloy after solution treatment has been studied by isothermal compression tests as well as quantitativemetallographic analysis. On the basis of the data obtained from the tests, predicting models for equivalent grainsize and recrystallization volume fraction have been established with an artificial neural network method. An FEnumerical simulation system has been developed to simulate the distribution of microstructure in Ti-15-3 alloy afterhot back extrusion and solution treatment by combining the neural network model with thermal-mechanical coupledrigid-viscoplastic FE model. Corresponding experimental research is performed. The agreement of the simulatedresults with measured ones shows that the simulation system is reliable.
文摘Hot compression experiments were conducted on Ti 15 3 alloy specimens using Gleeble 1500 Thermal Simulator.These tests were focused to obtain the flow stress data under various conditions of strain,strain rate and temperature. On the basis of these data, the predicting model for the nonlinear relation between flow stress and deformation strain,strain rate and temperature for Ti 15 3 alloy was developed with a back propagation artificial neural network method. Results show that the neural network can reproduce the flow stress in the sampled data and predict the nonsampled data well. Thus the neural network method has been verified to be used to tackle hot deformation problems of Ti 15 3 alloy. [
文摘The key problems of cold power spinning of Ti-15-3 alloy are studied. Reasonable billet preparation methods are presented to improve crystal structure and avoid crack of billet. Influences of original wall thickness, reduction rate and feed rate on expanding in diameter are analyzed and some methods to prevent expanding in diameter are given.
基金supported by the National Natural Science Foundation of China under grant No.50405020.
文摘Grain shape of the hot deforming alloy is an important of material. The fractal theory was applied to analyze index to character the microstructure and performance the recrystallized microstructure of Ti-15-3 alloy after hot deformation and solution treatment. The fractal dimensions of recrystallized grains were calculated by slit island method. The influence of processing parameters on fractal dimension and grain size was studied, It has been shown that the shapes of recrystallized grain boundaries are self-similar, and the fractal dimension varies from 1 to 2. With increasing deformation degree and strain rate or decreasing deformation temperature, the fractal dimension of grain boundaries increased and the grain size decreased. So the fractal dimension could characterize the grain shape and size. A neural network model was trained to predict the fractal dimension of recrystallized microstructure and the result is in excellent agreement with the experimental data.
文摘目的合成环己酮3-氯-1,2-丙二醇缩酮。方法采用浸渍法制备了H6P2W18O62/TiO2-SiO2催化剂,并采用FT-IR、XRD、SEM对其进行了表征。以环己酮和3-氯-1,2-丙二醇为原料,催化合成环己酮3-氯-1,2-丙二醇缩酮,采用FT-IR、1 H NMR、13 C NMR等表征手段来分析合成产物为环己酮3-氯-1,2-丙二醇缩酮。结果在酮醇摩尔比为1∶1.4,带水剂环己烷用量8mL,催化剂用量为反应物总质量的2.0%,反应时间1.0h的条件下,缩酮收率可达85.0%。催化剂重复使用5次后收率有72.6%。结论 H6P2W18O62/TiO2-SiO2催化剂对合成环己酮3-氯-1,2-丙二醇缩酮不仅反应时间短,催化剂用量少,而且产品收率高。
文摘Based on Kohler’s ternary solution model and Miedemaa’s model for calculating the heats of formation-△Hij of binary Systems, the integral equation has ben established for calculating the activity coefficients in ternarysolution. With the equation, the activity coefficients in Ti-15-3 melt have been calculated. The results show that allof components’ activity coefficients are less than 1, in other wolds, compared with ideal solution, all components takeon a negative deviation. At 2000K, the activity coefficients in Ti-15-3 melt are shown as: about 0.9 for Ti, about0.85 for V, about 0. 1 for Al, aboaut 0.5 for Cr and about 0.23 for Sn. me addition of V lowers the activity coefficient of Ti, but raise the ones of Al, Cr and Sn. These results can be directly used to calculate the evaporation loss ofAl, Cr and Sn during the ISM(Induction Skull Melting) process and at the same time estimate the reactivity betweenTi-15-3 melt and refractory during the cast production.
基金Project supported by the National Key Research and Development Program of China(Grant No.2021YFB3501300)the National Natural Science Foundation of China(Grant No.51731001)the Fund from the State Key Laboratory of Baiyunobo Rare Earth Resource Researches and Comprehensive Utilization’s Key Research and Development Projects。
文摘As concepts closely related to microwave absorption properties,impedance matching and phase matching were rarely combined with material parameters to regulate properties and explore related mechanisms.In this work,reduction–diffusion method was innovatively applied to synthesize rare earth alloy Y_(2)Fe_(17).In order to regulate the electromagnetic parameters of absorbers,the Y_(2)Fe_(17)N_(3-δ)particles were coated with silica(Y_(2)Fe_(17)N_(3-δ)@SiO_(2))and absorbers with different volume fractions were prepared.The relationship between impedance matching,matching thickness,and the strongest reflection loss peak(RLmin)was presented obviously.Compared to the microwave absorption properties of Y_(2)Fe_(17)N_(3-δ)/PU absorber,Y_(2)Fe_(17)N_(3-δ)@SiO_(2)/PU absorbers are more conducive to the realization of microwave absorption material standards which are thin thickness,light weight,strong absorbing intensity,and broad bandwidth.Based on microwave frequency bands,the microwave absorption properties of the absorbers were analyzed and the related parameters were listed.As an important parameter related to perfect matching,reflection factor(√ε_(r)/μ_(r))was discussed combined with microwave amplitude attenuation.According to the origin and mathematical model of bandwidth,the formula of EAB(RL<-10 dB)was derived and simplified.The calculated bandwidths agreed well with experimental results.
