Microstructure and mechanical properties of hypereutectic Al-Si alloy modified with Cu-P

The microstructure and mechanical properties of Al-14.6Si castings modified by Cu-P master alloy under different conditions were studied with optical microscope（OM） and mechanical testing and simulation（MTS）.The results indicate that the Cu-P master alloy possesses not only obvious modification effect,but also longevity effect with more than 8 h on the hypereutectic Al-Si alloy.It is shown from thermal calculation,scanning electron microscope（SEM）,and energy dispersive analysis of X-rays（EDAX） that the modification mechanism of Cu-P on primary silicon in the castings is heterogeneous nucleation around AlP particles.The Cu-P master alloy has no or little modifying effect on eutectic silicon,even though it has obvious modification on primary silicon in the castings.This may be because of the fast transformation of eutectic silicon at a very narrow temperature,which will notably weaken the role of AlP particles as heterogeneous nuclei for eutectic silicon.

Microstructure evolution and phase transformation of traditional cast and spray-formed hypereutectic aluminium-silicon alloys induced by heat treatment

Microstructural evolution and phase transformation induced by different heat treatments of the hypereutectic aluminium-silicon alloy, Al-25Si-5Fe-3Cu （wt%, signed as 3C）, fabricated by traditional cast （TC） and spray forming （SF） processes, were investigated by differential scanning calorimetry （DSC） and scanning electron microscopy （SEM） combined with energy dispersive X-ray spectroscopy and X-ray diffraction techniques. The results show that A17Cu2Fe phase can be formed and transformed in TC- and SF-3C alloys between 802-813 K and 800-815 K, respectively. The transformation from β-Al5FeSi to δ-Al4FeSi2 phase via peritectic reaction can occur at around 858-870 K and 876-890 K in TC- and SF-3C alloys, respectively. The starting precipitation temperature of δ-Al4FeSi2 phase as the dominant Fe-bearing phase in the TC-3C alloy is 997 K and the exothermic peak about the peritectic transformation of δ-Al4FeSi2→β-Al5FeSi is not detected in the present DSC experiments. Also, the mechanisms of the microstructural evolution and phase transformation are discussed.

Effect of mixing rate and temperature on primary Si phase of hypereutectic Al-20Si alloy during control ed diffusion solidification(CDS) process

Controlled Diffusion Solidification(CDS) is a promising process relied on mixing two liquid alloys of precisely controlled chemistry and temperature in order to produce a predetermined alloy composition. In this study, the CDS was employed to prepare hypereutectic Al-20%Si(mass fraction) alloy using Al-30%Si and pure Al of different temperatures. The mixing rate was controlled using three small crucibles with a hole of different diameters in their bottom. The effect of mixing rate and temperature on the microstructure of the primary Si-phase during the mixing of molten Al and Al-30%Si was studied. The results showed that when the diameter of the small crucible bottom hole is 16 mm, a higher mass mixing rate 0.217 kg·s-1 would results in a lower stream velocity 0.414 m·s-1. Conversely a lower mass mixing rate 0.114 kg·s-1(the diameter of the small crucible bottom hole is 8 mm) would result in a higher fluid stream velocity 0.879 m·s-1. A lower mass mixing rate would be better to refine the primary Si than a higher mass mixing rate. Meanwhile, the morphology and distribution of primary Si could also be improved. Especially, when Al-30%Si alloy at 820 °C was mixed with pure Al at 670 °C in the case of a mass mixing rate of 0.114 kg·s-1 and a pouring temperature of 680 °C, the average size of the primary Si phase would be only 18.2 μm. Its morphology would mostly be octahedral and the primary Si would distribute uniformly in the matrix microstructure. The lower mass mixing rate(0.114 kg·s-1) will enhance the broken tendency of Al-30%Si steam and the mixing agitation of resultant melt, so the primary Si phase can be better refined.

Mechanical properties of hypereutectic Al-Si alloy by semisolid processing

Semisolid hypereutectic Al Si alloy billets were obtained by electromagnetic stirring, in which microstructure of primary silicon gets rounder and there are a large number of rosette α phases appearing. Compared with conventional gravity die casting alloys, the tensile strength and elongation of semisolid forming hypereutectic Al Si get obviously improved. Change of primary silicon morphology of semisolid hypereutectic Al Si alloy made by electromagnetic stirring is the main reason of better tensile strength, and a large number of rosette α phases precipitation is the main reason of better elongation.

Microstructure and Property of Hypereutectic High Chromium Cast Iron Prepared by Slope Cooling Body-Centrifugal Casting Method

In this paper, the ring-type ingot of hypereutectic high Cr cast iron was obtained by slope cooling bodycentrifugal casting method （SC-CCM）, and its microstructure and impact toughness were investigated, respectively. The results indicated that, first, the primary carbides in the microstructure are prominently finer than those in the hypereutectic high Cr cast iron prepared by conventional casting method. Second, in the ring-type ingot, the primary carbides near radial outer field are finer than those near radial inner field; furthermore, there is dividing field in the microstructure. Finally, the impact toughness values of the specimens impacted on the radial outer face and on the radial inner face are improved respectively about 36% and 138% more than that of the hypereutectic high Cr one prepared by conventional casting method.

Effect of partial remelting time on the initial carbide in semisolid structure of hypereutectic high Cr cast iron

In order to review the effect of partial remelting time on the morphology of initial carbides, semisolid ingots of hypereutectic high Cr17 cast iron were remelted at 1270℃ for four different times, and the changing characteristics of shape factor and the equivalent diameter of initial carbides were analyzed quantitatively using a Leica image analyzer. The results indicate that firstly, the evolution process of the initial carbides' morphology undergoes melting, spheroidization and refining during the partial remelting; secondly, the solute diffusion and interface tension take dominant roles at the primary and the middle-final stages respectively in the process of initial carbide evolution; finally, a perfect structure can be obtained by remelting semisolid ingots at 1270℃ for 15 min.

Characteristics and Microstructure of a Hypereutectic Al-Si Alloy Powder by Ultrasonic Gas Atomization Process

A hypereutectic Al-Si alloy powder was prepared by ultrasonic gas atomization process. The morphologies, microstructure and phase constituent of the alloy powder were studied. The results showed that powder of the alloy was very fine and its microstructure was mainly consisted of Si crystals plus intermetallic compound A19FeSi3, which were.very fine and uniformly distributed.

Improving chill control in iron powder treated slightly hypereutectic grey cast irons

Recent studies revealed that in eutectic to slightly hypereutectic grey irons(CE = 4.3%-4.5%) the presence of austenite dendrites provides an opportunity to improve the cast iron properties,as a high number of eutectic cells are "reinforced" by austenite dendrites.An iron powder addition proved to be important by promoting dendritic austenite in hypereutectic irons,but was accompanied by adverse effect on the characteristics of potential nuclei for graphite.The purpose of the present paper is to investigate the solidification pattern of these irons.Chill wedges with different cooling moduli(CM = 0.11-0.43 cm) were poured in resin bonded sand and metal moulds.Relative clear /mottled /total chill measurement criteria were applied.Iron powder additions led to a higher chill tendency,while single inoculation showed the strongest graphitizing effect.The various double treatments show an intermediate position,but the inoculant added after iron powder appears to be the most effective in reducing base iron chill tendency,for all cooling moduli and chill evaluation parameters.This performance reflects the improved properties of(Mn,X)S polygonal compounds as nucleation sites for graphite,especially in resin bonded sand mould castings.Both austenite and graphite nucleation benefit from a double addition of iron powder + inoculant,with positive effect on the final structure and chill tendency.

Semi-solid characteristics and thixoforming of hypereutectic Al-Si alloy

Effects of processing parameters on microstructure evolutions by mechanical stirring, procedures for obtaining thixotropy in semi solid slurries, and procedure for thixoforging component, were investigated in hypereutectic Al Si alloy. It is shown that 605 ℃ was the proper temperature for stirring treatment of this alloy, at which the coarse and plate primary Si crystals were effectively changed to globular crystals with a mean diameter of 200 μm after 50 min stirring, that billets with excellent thixotropy were obtained after 50 min remelting at 575 ℃, in which solid fraction of matrix and primary Si crystals was about 60%, and that a perfect near net shape component of disc casting was obtained by thixoforging.

Microstructure Characteristics and Apparent Viscosity of Hypereutectic Al-24%Si Alloy Melt During Semi-solid State Stirring

The microstructural evolution and apparent viscosity of hypereutectic Al-24%Si alloy during semi-solid state shearing were studied with a Searte type viscometer. When the alloy melt was continuously stirred from 720 degreesC to eutectic temperature, the primary Si crystals were gradually changed from elongated platelets to near-spherical shapes. It was found that some nondendritic a-phase formed when the melt was stirred below 585 degreesC. The experiment showed that the semi-solid stirring had strong effect on inhibiting the anisotropic growth of Si crystals during solidification. The apparent viscosity of the alloy melt increased slowly with the decreasing of temperature before the formation of nondendritic alpha -phase, which caused the dramatic increase of apparent viscosity.

Effects of P+Cr complex modification and solidification conditions on microstmcture of hypereutectic Al-Si alloys by wedge-shaped copper mould casting

Large and segregated primary Si particles may drastically decrease the mechanical properties of Al-Si alloys. To solve this problem, a P-Cr complex modif ier was added into the alloy, and the effects of P-Cr complex modification and solidification conditions on the microstructure of hypereutectic Al-Si alloys casting produced in wedge-shaped copper mould were studied. The thermal analysis technique was applied to calculate the cooling rate during solidification. The microstructures were observed by means of optical and scanning electron microscopies. Results showed that the primary Si segregates in the as-cast hypereutectic Al-Si alloys. The segregation of primary Si can be inhibited by adding a P+Cr complex modif ier and increasing the cooling rate during solidif ication. The ref inement of primary Si particles by P+Cr complex modif ication is due to the formation of CrS i2 and AlP particles which act as the heterogeneous nuclei for the primary Si phase. The segregation of Si was also inhibited through the adherence of heavier CrS i2 particles to the primary Si particles.

Modification and aging precipitation behavior of hypereutectic AI-21wt.%Si alloy treated by P+Ce combination

In the present study, the tested hypereutectic Al-21 wt.%Si alloys were prepared by modifying the melt using different proportions of P and Ce, and then applying T6 heat treatment. The modif ication effects and mechanism of P+Ce complex modif ier on the Si phase of hypereutectic Al-21 wt.%Si alloy were studied, and the aging precipitation behavior after modif ication was characterized by means of tensile strength measurement, OM, SEM and TEM analysis. The results show that the massive primary silicon phase particles are signif icantly ref ined after modif ication, while the needle-like eutectic silicon crystals become f ibrous and short. It was found that the mechanism of phosphorus modifi cation on the primary silicon can be attributed to heterogeneous nucleation of Al P, while the modification mechanism of Ce can be explained by adsorbing-twinning theory. In the aged microstructure of the modif ied hypereutectic Al-21 wt.%Si alloy, there existed some strengthening phases such as Al4Cu9, Al2 Cu, AlC u3, and Al57Mn12. The P+Ce complex modif ier not only affected the size of primary silicon and eutectic silicon, but also the aging behavior of alloys under the heat treatment process. When Al-21 wt.%Si alloy was modif ied using 0.08%wt.P + 0.6wt.% Ce, the aging precipitates were dispersed uniformly in the alloy, and its mechanical properties at room and elevated temperatures are optimized(Rm = 287.6 MPa at RT, Rm = 210 MPa at 300 ℃).

Refinement and thermal analysis of hypereutectic Al-25%Si alloy

Refinement and thermal analysis of hypereutectic Al 25%Si alloy were investigated with scanning electron microscope (SEM) and differential scanning calorimeter (DSC). The results show that the average size of primary silicon in Al 25%Si alloy without and with phosphorus addition are 250 μm and 30 μm, respectively. But the primary and eutectic growth temperature is raised by about 17.3 ℃ and 4?℃ respectively due to phosphorus addition. The primary nucleation temperatures are 745.0 ℃ and 762.0 ℃ for untreated and treated samples and in addition, the enthalpy changes of primary and eutectic transformation are -261.0 J/g and -397.3 J/g without phosphorus addition, -294.2 J/g and -386.1 J/g with phosphorus addition, respectively. Otherwise the mechanisms of refinement and thermal transformation of Al 25%Si alloy in solidifying process are also discussed. [

Influence of hydrogen content on the behavior of grain reflnement in hypereutectic aluminum-silicon alloy

Dissolved hydrogen is harmful to mechanical properties of refinedhypereutectic aluminum-silicon alloys. In the present work, by using a stepped-form mold and thehydrogen-detecting instrument HYSCAN II, the relationship between the initial hydrogen content inthe melt and the refinement effect on the casting of hypereutectic aluminum-silicon alloy wasinvestigated. The experimental results show that the cooling rate, the hydrogen content and thegrain refinement effect are three interactive factors. When the hydrogen content is above 0.20mL/100 g and the cooling rate is lower than that in 50 mm-thick step, hydrogen dissolved in thealloy melt influences the grain refinement effect. With increasing the cooling rate, the criticalhydrogen content increases too. It is expected that much hydrogen in the melt make the netinterfacial energy larger than or equal to zero, resulting in the shielding of the particles AlPduring solidification and that the critical gas content is closely related to the critical radius ofembryo bubbles.

Effect of Nd on Microstructure and Mechanical Properties of Hypereutectic Al-25Si Alloy

The modification mechanism of Nd on Al-25Si alloy was studied. The result showed that pure Nd (0.3%) could significantly refine primary silicon in hypereutectic Al-25Si alloy. And the morphology of primary silicon was transformed from star-shaped to block and the size of primary silicon changed from 150～200 μm to 40～80 μm after modification. The morphology of silicon and elements presence was detected by means of SEM-EDS, XRD was carried out to detect the phase constitution before and after modification. It was found that no new phase formed and the lattice of silicon and aluminum increased after modification and most of Nd may exist as solids solute element of silicon and absorb on the surface of silicon. Mechanical property test results showed that after modification with 0.3% Nd, Tensile strength increased about 33% from 138 to 184 MPa, yield strength increased about 15% from 126 to 145 MPa, and elongation change was not obvious. The improvement of mechanical property should attribute to fine grain strength and purification of base metal after modification.

Hydrogen Content and Porosity Behavior of Hypereutectic Aluminum-silicon Alloy with Phosphorus

By making castings that pick up gas from moisture in red sand molds,the porosity generated at different cooling rates was discussed during solidification of hypereutectic Al-25%Si alloy without and with phosphorus additions. The effect of phosphorus addition on hydrogen content in the melt was also studied. It was observed that the phosphorus addition made hydrogen content in alloy melts present a “see-saw' tendency.In addition to primary silicon refinement,the phosphorus promoted gas porosity formed not only in slowly cooled sections, but also in rapidly cooled sections. There was a small difference in density of full dense sample between P-refined and unrefined castings, with a larger density associated with phosphorous addition. The change of the surface tension seemed more reasonable to explain the mechanism of porosity behavior.

Multiplex modification with rare earth elements and P for hypereutectic A1-Si alloys

The effect of rare earth （RE） elements on the morphologies and sizes of Si phases in the hypereutectic A1-Si alloys modified with P was investigated. The results show that the addition of La element to the hypereutectic A1-Si alloys can enhance the effect of P element on the modification of the primary Si phases. In the multiplex modification of RE-P, the primary Si phase is refiner and the shape of the eutectic Si is changed from long needle-like to short rod-like. Moreover, the agglomeration rate of the primary Si phase is slowed greatly. Even the melt is held for 6 h, the average size of the primary Si phase is still satisfied. The results analyzed by scanning electron microscope （SEM） indicate that La is richer at A1-Si interface than that in α-A1 or primary Si phase. The higher the La content in the A1-Si interface, the smaller the primary Si phase.

Hypereutectic Al-Si Matrix Composites Prepared by In Situ Fe_(2)O_(3)/Al System

Al_(2)O_(3) particles reinforced hypereutectic Al-Si composites were prepared by in situ Fe_(2)O_(3)/Al reaction system.The thermodynamic analysis and microstructure evolution were investigated by differential scanning calorimetry,optical microscope,scanning electronic microscopy and transmission electron microscope.Results show that the reaction between Fe_(2)O_(3) and Al is spontaneous which can be separated into two steps at different temperatures.The in situ Al_(2)O_(3) particles in nano size distribute on the Al matrix accompanied with long needle-shapedβFe-rich intermetallic phase.With different content of Mn addition,βphase can be modified toα-Al15(Mn,Fe)3Si2 andδ-Al4(Fe,Mn)Si2.Both tensile strength and elongation results at room temperature and 300℃reveal that the optimal Fe-rich intermetallic phase is finer Chinese-script and polyhedralαphase with a Mn/Fe mass ratio 0.5 for the composites.Both in situ Al_(2)O_(3) particles andα-Fe phases contribute to the properties improvement of the composites。

Effect of Cu-Ni and Cu-Ni-Mn on the Microstructural and Mechanical Behaviour of As-Cast Non-Inoculated Hypereutectic Grey Iron

The hypereutectic region of grey cast iron has received very little attention especially for designing cast products by researchers. Due to its high carbon equivalence, hypereutectic grey iron poses some challenges especially its tendency for grey to white transition (GWT) at this level of carbon content. However, hypereutectic grey iron possesses inherent properties that could be easily utilized for improved performance in automobile engines and brake pad system. Significantly, they could be modified for superior hardness, strength and toughness. This study presents the effect of microalloying on the mechanical behaviour of hypereutectic grey cast iron with carbon equivalence above 4.5. The first part of this work presented in this paper considers the addition of Cu-Ni and Cu-Ni-Mn to series of as-cast hypereutectic grey cast iron and their hardness and tensile strength were studied and compared. A total of 33 cast samples were obtained with the control sample. The examination of the micrographs revealed that graphite eutectics cells of Type A and A + D were obtained in the resulting microstructure. Results analyses showed that the ferrite forming tendency of silicon was suppressed due to the high carbon content of the as-cast hypereutectic grey iron coupled with the absence of inoculation which plays a great role in the graphite flake type, network, size and distribution. Cu-Ni microalloying was also confirmed to promote hardness with the hardening effect limit of nickel observed at 1.3% composition. For Cu-Mi-Mn addition, excess and free sulphur in the hyper- eutectic grey iron results in reverse effect of manganese on strength, hardness, reduced graphite flake size and shape.

Effect of Squeeze Casting on Microstructure and Mechanical Properties of Hypereutectic Al-xSi Alloys

The effect of squeeze casting on microstructure and mechanical properties of hypereutectic Al-xS i alloys（x = 15, 17.5, 22 wt%） was investigated in this study. Results show that microstructure of the hypereutectic Al-x Si alloys was obviously improved by squeeze casting. The amount of coarse primary Si phase decreased, while that of fine primary α-Al dendrites increased with the increase of squeeze casting pressure. Due to the decrease of coarse primary Si particles, cracking of the matrix was reduced, whilst the fine microstructure, and mechanical properties of the squeeze casting alloys were improved. Compared with gravity casting alloys, mechanical properties of the hypereutectic Al-xS i alloys solidified at 600 MPa were improved significantly. Hardness of the squeeze casting hypereutectic Al-（15, 17.5, 22 wt%） Si alloys was improved by 15.91%, 12.23%, 17.48%, ultimate tensile strength was improved by 37.85%, 32.27%, 22.74%,and elongation was improved by 55.83%, 167.86%, 126.76%, respectively. Due to the uniform distribution of Si phases in squeeze casting Al-x Si alloys, their wear resistance was markedly enhanced.