Shape-selective methylation of 2-methylnaphthalene (2-MN) was carried out over NH 4 F and Pt modified HZSM-5 (SiO 2 /Al 2 O 3 = 83) catalysts in a fixed-bed down-flow reactor using methanol as methylating agent and 1,...Shape-selective methylation of 2-methylnaphthalene (2-MN) was carried out over NH 4 F and Pt modified HZSM-5 (SiO 2 /Al 2 O 3 = 83) catalysts in a fixed-bed down-flow reactor using methanol as methylating agent and 1,3,5-trimethylbenzene (1,3,5-TMB) as a solvent. Pt promoted HZSM-5 catalysts showed low concentration of coke-like polycondensed aromatics, NH 4 F modification decreased non-shape-selective acid sites. After Pt and NH 4 F co-modification, both conversion of 2-MN and selectivity to 2,6-DMN were improved. 6%NH 4 F/0.5%Pt/HZSM-5 catalyst exhibited 13.8% of 2-MN conversion with 6.2% of 2,6-DMN yield after 7 h time on stream (TOS), and 2,6-/2,7-DMN ratio of 1.7 after 10 h of TOS.展开更多
Three industry-supplied, well-shaped Mo/HZSM-5 catalysts, two binder-added and one binder-free, were tested for the first time in methane dehydroaromatization to benzene at 1073 K and 10000 mL/(g·h) in periodic...Three industry-supplied, well-shaped Mo/HZSM-5 catalysts, two binder-added and one binder-free, were tested for the first time in methane dehydroaromatization to benzene at 1073 K and 10000 mL/(g·h) in periodic CH4-H2 switch operation mode, and their catalytic performances were compared with those of three self-prepared, binder-free powder Mo/HZSM-5 catalysts. XRD, 27Al NMR, SEM, BET and NH3-TPD characterizations of all the catalysts show that the zeolites in the two binder-added catalysts are comparable to those in the three binder-free powder catalysts in crystallinity, crystal size, micropore volume and Br{/o}nsted acidity. The test results, on the other hand, show that the catalytic performances of the two binder-added catalysts are worse than those of the four binder-free catalysts on both catalyst mass and zeolite mass bases. Then, TPO and BET measurements of all spent samples were conducted to get a deep insight into the negative effects of binder addition, and the results suggest that the binder additives functioned mainly to enhance the polyaromatization of formed aromatics to coke on their external surfaces and consequently lower the catalysts' benzene formation activity and selectivity.展开更多
The non-oxidative aromatization of mixed CH4 with C3H8 over La-promoted Zn/HZSM-5 catalysts was studied in a fixed-bed reactor at 823 K with space velocity 600 h^-1 and CH4/C3H8 (mol ratio)=5:l. The propane convers...The non-oxidative aromatization of mixed CH4 with C3H8 over La-promoted Zn/HZSM-5 catalysts was studied in a fixed-bed reactor at 823 K with space velocity 600 h^-1 and CH4/C3H8 (mol ratio)=5:l. The propane conversion and the aromatic selectivities were up to 99% and 60% over the catalyst respectively, while methane conversion had an induction period with the highest conversion of 30%. The structure and surface acidity of the catalysts were characterized by XRD, NH3-TPD and TG-DTA. The influences of reaction and regenerative conditions on the activity and selectivity were also investigated.展开更多
A series of Fe/HZSM-5 catalysts with different iron loadings were prepared by impregnation method.Characterization was performed by N2 adsorption-desorption,X-ray diffraction(XRD),NH3 temperature-programmed desorpt...A series of Fe/HZSM-5 catalysts with different iron loadings were prepared by impregnation method.Characterization was performed by N2 adsorption-desorption,X-ray diffraction(XRD),NH3 temperature-programmed desorption(NH3-TPD),temperature-programmed reduction (TPR),temperature-programmed oxidation(TPO)and thermogravimetry(TG)analysis.Iron content in the synthesized samples varied from 1.1 wt%to 20 wt%.The obtained samples have been used for ethanol conversion into light olefins.It was found that the amount of strong acidity at 300 -5 50-C on Fe-modified samples was decreased,going with another new acid site appearance at 550- 600-C and that Fe/HZSM-5 catalysts were highly selective towards light olefins,especially the 9FZ sample.In addition,Fe-modified catalysts suppressed the conversion of ethanol to aromatics and paraffins and enhanced their anti-carbon deposit ability.展开更多
The effect of steam-treatment to HZSM-5 zeolite and Mo/HZSM-5 with a steaming time range of 0.5-1 h on the catalytic performance of methane dehydro-aromatization (MDA) over Mo/HZSM-5 catalyst prepared with impregnat...The effect of steam-treatment to HZSM-5 zeolite and Mo/HZSM-5 with a steaming time range of 0.5-1 h on the catalytic performance of methane dehydro-aromatization (MDA) over Mo/HZSM-5 catalyst prepared with impregnation has been studied in detail in combination with the characterization of 1H MAS NMR technique. Both the deactivation rate constant (kd) and the Brtnsted acid sites per unit cell were calculated to quantitatively evaluate the stability of Mo/HZSM-5 catalysts treated with steam at 813 K before and after impregnation of molybdenum species, and the corresponding variation of their Brtnsted acid sites. The results reveal that a V-shape relationship between kd and the number of B 1 acid sites per unit cell is presented on Mo/HZSM-5 catalyst under the tested steam-treatment and reaction conditions.展开更多
The optimum Mo/[H^+] ratio per unit cell of the active precursors in Mo/HZSM-5 catalysts for methane dehydro-aromatization, measured by1H MAS NMR, was found to be about 1 when adjusting the acid sites by altering eith...The optimum Mo/[H^+] ratio per unit cell of the active precursors in Mo/HZSM-5 catalysts for methane dehydro-aromatization, measured by1H MAS NMR, was found to be about 1 when adjusting the acid sites by altering either the SiO2/Al2O3 ratios or the Mo loading. This implies that a concerted interaction between the Mo species and the Bronsted acid sites probably features the bifunctionality of the Mo/HZSM-5 catalyst. On the other hand, it was found that the driving force for Mo species to move into the HSZM-5 zeolite channels and the interaction between the Mo species and the Bronsted acid sites are closely and proportionably related with the amount of Bronsted acid sites per unit cell.展开更多
Impregnation, mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite. The structure and surface acidity of the catalysts were studied by means of XRD, FT...Impregnation, mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite. The structure and surface acidity of the catalysts were studied by means of XRD, FT-IR, NH3-TPD, TPR and XPS. The effects of Mo content and reaction time on stream on the aromatization of propane were investigated. It was found that the performance of the Mo/HZSM-5 catalyst prepared by the hydrothermal treatment method was much better than that of the other two catalysts. For example, under the reaction conditions of 823 K and 600 h-1, propane conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%, respectively. XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5, and larger amounts of them could penetrate into the HZSM-5 channel, as compared with the other two kinds of catalysts. These factors may be responsible for their high activities for propane aromatization. IR and NH3-TPD studies indicated that the number of Bronsted acid centers decreased and the Lewis acid centers increased after Mo was introduced into the HZSM-5 zeolite.展开更多
The dehydroaramatization of methane over W-supported ZSM-5 with varying degrees of Li+ ion-exchanged catalysts was studied with and without oxygen at 1073 K and atmospheric pressure. Catalyst activity and stability we...The dehydroaramatization of methane over W-supported ZSM-5 with varying degrees of Li+ ion-exchanged catalysts was studied with and without oxygen at 1073 K and atmospheric pressure. Catalyst activity and stability were found to be influenced by the catalyst acidity related to Bronsted acid sites and by the presence of oxygen in the feed. The NH3-TPD and FTIR-pyridine results demonstrated that partially exchanged of H+ ions by Li+ into the W/HZSM-5 catalysts could be used to control the amount of strong acid sites on the catalyst surface. Without oxygen, the 3WHLi-Z (5:1) catalyst that has strong acid sites equal to nearly 74% of the original strong acid sites in the parent HZSM-5 exhibited the highest methane conversion and selectivity towards aromatics. However, the catalyst deactivated in a five hour period. In the presence of oxygen, the catalyst activity and stability could be improved further. The results of this study revealed that a suitable amount of strong Bronsted acid sites as well as oxygen addition in the feed increased the catalyst activity and stability. The 3WHLi-Z(5:1) catalyst exhibited improved performance in the dehydroaromatization of methane.展开更多
Mo/HZSM-5 is a good catalyst for methane aromatization, and the reaction,performance of Mo/HZSM-5 and Cu modified Mo/HZSM-5 catalysts under various pretreatment conditionshas been studied. The results indicate that th...Mo/HZSM-5 is a good catalyst for methane aromatization, and the reaction,performance of Mo/HZSM-5 and Cu modified Mo/HZSM-5 catalysts under various pretreatment conditionshas been studied. The results indicate that the catalyst presented a distinguished catalyticactivity, benzene selectivity and a high stability when the bed temperature was raised in N_2atmosphere.展开更多
The intrinsic reaction kinetics of methane aromatization under non-oxidative conditions over modified Mo/HZSM-5 catalysts was studied in the quartz pipe-reactor under ordinary pressure with the temperature ranging fro...The intrinsic reaction kinetics of methane aromatization under non-oxidative conditions over modified Mo/HZSM-5 catalysts was studied in the quartz pipe-reactor under ordinary pressure with the temperature ranging from 913.15 to 973.15 K and the space velocity from 700 to 2100 ml/(g·h). The Langmuir-Hinshelwood model was chosen to describe the intrinsic kinetics while Levenberg-Marquardt method was selected to determine the parameters in the kinetic model. Statistical test and residual error distribution diagrams showed that experimental data were in good agreement with calculated data, and Langmuir-Hinshelwood model was suitable for the description of the intrinsic kinetics of methane aromatization under the reaction conditions discussed in this article.展开更多
The electrochemical coupling of biomass oxidation and nitrogen conversion presents a potential strategy for high value-added chemicals and nitrogen cycling.Herein,in this work,CuO/Co_(3)O_(4)with heterogeneous interfa...The electrochemical coupling of biomass oxidation and nitrogen conversion presents a potential strategy for high value-added chemicals and nitrogen cycling.Herein,in this work,CuO/Co_(3)O_(4)with heterogeneous interface is successfully constructed as a bifunctional catalyst for the electrooxidation of 5-hydroxymethylfurfural to 2,5-furandicarboxylic acid and the electroreduction of nitrate to ammonia(NH_(3)).The open-circuit potential spontaneous experiment shows that more 5-hydroxymethylfurfural molecules are adsorbed in the Helmholtz layer of the CuO/Co_(3)O_(4)composite,which certifies that the CuO/Co_(3)O_(4)heterostructure is conducive to the kinetic adsorption of 5-hydroxymethylfurfural.In situ electrochemical impedance spectroscopy further shows that CuO/Co_(3)O_(4)has faster reaction kinetics and lower reaction potential in oxygen evolution reaction and 5-hydroxymethylfurfural electrocatalytic oxidation.Moreover,CuO/Co_(3)O_(4)also has a good reduction effect on NO_(3)^(-).The ex-situ Raman spectroscopy shows that under the reduction potential,the metal oxide is reduced,and the generated Cu_(2)O can be used as a new active site for the reaction to promote the electrocatalytic conversion of NO_(3)^(-)to NH_(3) synthesis.This work provides valuable guidance for the synthesis of value-added chemicals by 5-hydroxymethylfurfural electrocatalytic oxidation coupled with NO_(3)^(-)while efficiently producing NH_(3).展开更多
基金Supported by the Program for New Century Excellent Talents in University (NCET-04-0268)the Expertise-Introduction Project for Disciplinary Innovation of Universities
文摘Shape-selective methylation of 2-methylnaphthalene (2-MN) was carried out over NH 4 F and Pt modified HZSM-5 (SiO 2 /Al 2 O 3 = 83) catalysts in a fixed-bed down-flow reactor using methanol as methylating agent and 1,3,5-trimethylbenzene (1,3,5-TMB) as a solvent. Pt promoted HZSM-5 catalysts showed low concentration of coke-like polycondensed aromatics, NH 4 F modification decreased non-shape-selective acid sites. After Pt and NH 4 F co-modification, both conversion of 2-MN and selectivity to 2,6-DMN were improved. 6%NH 4 F/0.5%Pt/HZSM-5 catalyst exhibited 13.8% of 2-MN conversion with 6.2% of 2,6-DMN yield after 7 h time on stream (TOS), and 2,6-/2,7-DMN ratio of 1.7 after 10 h of TOS.
文摘Three industry-supplied, well-shaped Mo/HZSM-5 catalysts, two binder-added and one binder-free, were tested for the first time in methane dehydroaromatization to benzene at 1073 K and 10000 mL/(g·h) in periodic CH4-H2 switch operation mode, and their catalytic performances were compared with those of three self-prepared, binder-free powder Mo/HZSM-5 catalysts. XRD, 27Al NMR, SEM, BET and NH3-TPD characterizations of all the catalysts show that the zeolites in the two binder-added catalysts are comparable to those in the three binder-free powder catalysts in crystallinity, crystal size, micropore volume and Br{/o}nsted acidity. The test results, on the other hand, show that the catalytic performances of the two binder-added catalysts are worse than those of the four binder-free catalysts on both catalyst mass and zeolite mass bases. Then, TPO and BET measurements of all spent samples were conducted to get a deep insight into the negative effects of binder addition, and the results suggest that the binder additives functioned mainly to enhance the polyaromatization of formed aromatics to coke on their external surfaces and consequently lower the catalysts' benzene formation activity and selectivity.
基金This work is supported by the National Science Foundation of China (Grant Nos 20343002 20433030) and PetroChina.
文摘The non-oxidative aromatization of mixed CH4 with C3H8 over La-promoted Zn/HZSM-5 catalysts was studied in a fixed-bed reactor at 823 K with space velocity 600 h^-1 and CH4/C3H8 (mol ratio)=5:l. The propane conversion and the aromatic selectivities were up to 99% and 60% over the catalyst respectively, while methane conversion had an induction period with the highest conversion of 30%. The structure and surface acidity of the catalysts were characterized by XRD, NH3-TPD and TG-DTA. The influences of reaction and regenerative conditions on the activity and selectivity were also investigated.
基金supported by the National Natural Science Foundation of China(No.20963010)the Doctor Fund of Science Research(No.070267)
文摘A series of Fe/HZSM-5 catalysts with different iron loadings were prepared by impregnation method.Characterization was performed by N2 adsorption-desorption,X-ray diffraction(XRD),NH3 temperature-programmed desorption(NH3-TPD),temperature-programmed reduction (TPR),temperature-programmed oxidation(TPO)and thermogravimetry(TG)analysis.Iron content in the synthesized samples varied from 1.1 wt%to 20 wt%.The obtained samples have been used for ethanol conversion into light olefins.It was found that the amount of strong acidity at 300 -5 50-C on Fe-modified samples was decreased,going with another new acid site appearance at 550- 600-C and that Fe/HZSM-5 catalysts were highly selective towards light olefins,especially the 9FZ sample.In addition,Fe-modified catalysts suppressed the conversion of ethanol to aromatics and paraffins and enhanced their anti-carbon deposit ability.
基金supported by Foundation for University Key Teacher by the Education of Heilongjiang Province(No.1152G018)
文摘The effect of steam-treatment to HZSM-5 zeolite and Mo/HZSM-5 with a steaming time range of 0.5-1 h on the catalytic performance of methane dehydro-aromatization (MDA) over Mo/HZSM-5 catalyst prepared with impregnation has been studied in detail in combination with the characterization of 1H MAS NMR technique. Both the deactivation rate constant (kd) and the Brtnsted acid sites per unit cell were calculated to quantitatively evaluate the stability of Mo/HZSM-5 catalysts treated with steam at 813 K before and after impregnation of molybdenum species, and the corresponding variation of their Brtnsted acid sites. The results reveal that a V-shape relationship between kd and the number of B 1 acid sites per unit cell is presented on Mo/HZSM-5 catalyst under the tested steam-treatment and reaction conditions.
文摘The optimum Mo/[H^+] ratio per unit cell of the active precursors in Mo/HZSM-5 catalysts for methane dehydro-aromatization, measured by1H MAS NMR, was found to be about 1 when adjusting the acid sites by altering either the SiO2/Al2O3 ratios or the Mo loading. This implies that a concerted interaction between the Mo species and the Bronsted acid sites probably features the bifunctionality of the Mo/HZSM-5 catalyst. On the other hand, it was found that the driving force for Mo species to move into the HSZM-5 zeolite channels and the interaction between the Mo species and the Bronsted acid sites are closely and proportionably related with the amount of Bronsted acid sites per unit cell.
文摘Impregnation, mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite. The structure and surface acidity of the catalysts were studied by means of XRD, FT-IR, NH3-TPD, TPR and XPS. The effects of Mo content and reaction time on stream on the aromatization of propane were investigated. It was found that the performance of the Mo/HZSM-5 catalyst prepared by the hydrothermal treatment method was much better than that of the other two catalysts. For example, under the reaction conditions of 823 K and 600 h-1, propane conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%, respectively. XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5, and larger amounts of them could penetrate into the HZSM-5 channel, as compared with the other two kinds of catalysts. These factors may be responsible for their high activities for propane aromatization. IR and NH3-TPD studies indicated that the number of Bronsted acid centers decreased and the Lewis acid centers increased after Mo was introduced into the HZSM-5 zeolite.
文摘The dehydroaramatization of methane over W-supported ZSM-5 with varying degrees of Li+ ion-exchanged catalysts was studied with and without oxygen at 1073 K and atmospheric pressure. Catalyst activity and stability were found to be influenced by the catalyst acidity related to Bronsted acid sites and by the presence of oxygen in the feed. The NH3-TPD and FTIR-pyridine results demonstrated that partially exchanged of H+ ions by Li+ into the W/HZSM-5 catalysts could be used to control the amount of strong acid sites on the catalyst surface. Without oxygen, the 3WHLi-Z (5:1) catalyst that has strong acid sites equal to nearly 74% of the original strong acid sites in the parent HZSM-5 exhibited the highest methane conversion and selectivity towards aromatics. However, the catalyst deactivated in a five hour period. In the presence of oxygen, the catalyst activity and stability could be improved further. The results of this study revealed that a suitable amount of strong Bronsted acid sites as well as oxygen addition in the feed increased the catalyst activity and stability. The 3WHLi-Z(5:1) catalyst exhibited improved performance in the dehydroaromatization of methane.
文摘Mo/HZSM-5 is a good catalyst for methane aromatization, and the reaction,performance of Mo/HZSM-5 and Cu modified Mo/HZSM-5 catalysts under various pretreatment conditionshas been studied. The results indicate that the catalyst presented a distinguished catalyticactivity, benzene selectivity and a high stability when the bed temperature was raised in N_2atmosphere.
文摘The intrinsic reaction kinetics of methane aromatization under non-oxidative conditions over modified Mo/HZSM-5 catalysts was studied in the quartz pipe-reactor under ordinary pressure with the temperature ranging from 913.15 to 973.15 K and the space velocity from 700 to 2100 ml/(g·h). The Langmuir-Hinshelwood model was chosen to describe the intrinsic kinetics while Levenberg-Marquardt method was selected to determine the parameters in the kinetic model. Statistical test and residual error distribution diagrams showed that experimental data were in good agreement with calculated data, and Langmuir-Hinshelwood model was suitable for the description of the intrinsic kinetics of methane aromatization under the reaction conditions discussed in this article.
基金the support received from the National Natural Science Foundation of China(Grant No.22372012,22261160640,and 22002009)the Natural Science Foundation of Hunan Province(Grant No.2023JJ20037 and 2021JJ40565)the Scientific Research Project of Hunan Provincial Department of Education(Grant No.22B0293)
文摘The electrochemical coupling of biomass oxidation and nitrogen conversion presents a potential strategy for high value-added chemicals and nitrogen cycling.Herein,in this work,CuO/Co_(3)O_(4)with heterogeneous interface is successfully constructed as a bifunctional catalyst for the electrooxidation of 5-hydroxymethylfurfural to 2,5-furandicarboxylic acid and the electroreduction of nitrate to ammonia(NH_(3)).The open-circuit potential spontaneous experiment shows that more 5-hydroxymethylfurfural molecules are adsorbed in the Helmholtz layer of the CuO/Co_(3)O_(4)composite,which certifies that the CuO/Co_(3)O_(4)heterostructure is conducive to the kinetic adsorption of 5-hydroxymethylfurfural.In situ electrochemical impedance spectroscopy further shows that CuO/Co_(3)O_(4)has faster reaction kinetics and lower reaction potential in oxygen evolution reaction and 5-hydroxymethylfurfural electrocatalytic oxidation.Moreover,CuO/Co_(3)O_(4)also has a good reduction effect on NO_(3)^(-).The ex-situ Raman spectroscopy shows that under the reduction potential,the metal oxide is reduced,and the generated Cu_(2)O can be used as a new active site for the reaction to promote the electrocatalytic conversion of NO_(3)^(-)to NH_(3) synthesis.This work provides valuable guidance for the synthesis of value-added chemicals by 5-hydroxymethylfurfural electrocatalytic oxidation coupled with NO_(3)^(-)while efficiently producing NH_(3).