Effect of ion stress on properties of magnetized plasma sheath

In the plasma sheath, there is a significant gradient in ion velocity, resulting in strong stress on ions treated as a fluid. This aspect has often been neglected in previous sheath studies. This study is based on the Braginskii plasma transport theory and establishes a 1D3V sheath fluid model that takes into account the ion stress effect. Under the assumption that ions undergo both electric and diamagnetic drift in the presheath region, self-consistent boundary conditions,including the ion Bohm velocity, are derived based on the property of the Sagdeev pseudopotential.Furthermore, assuming that the electron velocity at the wall follows a truncated Maxwell distribution, the wall floating potential is calculated, leading to a more accurate sheath thickness estimation. The results show that ion stress significantly reduces the sheath thickness, enhances ion Bohm velocity, wall floating potential, and ion flux at the wall. It hinders the acceleration of ions within the sheath, leading to notable alterations in the particle density profiles within the sheath. Further research indicates that in ion stress, bulk viscous stress has the greatest impact on sheath properties.

Investigations on MoS_(2)plasma by infra-red pulsed laser irradiation in high vacuum

MoS_(2)targets were irradiated by infra-red(IR)pulsed laser in a high vacuum to determine hot plasma parameters,atomic,molecular and ion emission,and angular and charge state distributions.In this way,pulsed laser deposition(PLD)of thin films on graphene oxide substrates was also realized.An Nd:YAG laser,operating at the 1064 nm wavelength with a 5 ns pulse duration and up to a 1 J pulse energy,in a single pulse or at a 10 Hz repetition rate,was employed.Ablation yield was measured as a function of the laser fluence.Plasma was characterized using different analysis techniques,such as time-of-flight measurements,quadrupole mass spectrometry and fast CCD visible imaging.The so-produced films were characterized by composition,thickness,roughness,wetting ability,and morphology.When compared to the MoS_(2)targets,they show a slight decrease of S with respect to Mo,due to higher ablation yield,low fusion temperature and high sublimation in vacuum.The pulsed IR laser deposited Mo Sx(with 1<x<2)films are uniform,with a thickness of about 130 nm,a roughness of about 50 nm and a higher wettability than the MoS_(2)targets.Some potential applications of the pulsed IR laser-deposited Mo Sx films are also presented and discussed.

Efficient ion acceleration driven by a Laguerre–Gaussian laser in near-critical-density plasma

Laser-driven ion accelerators have the advantages of compact size,high density,and short bunch duration over conventional accelerators.Nevertheless,it is still challenging to generate ion beams with quasi-monoenergetic peak and low divergence in experiments with the current ultrahigh intensity laser and thin target technologies.Here we propose a scheme that a Laguerre–Gaussian laser irradiates a near-critical-density(NCD)plasma to generate a quasi-monoenergetic and low-divergence proton beam.The Laguerre–Gaussian laser pulse in an NCD plasma excites a moving longitudinal electrostatic field with a large amplitude,and it maintains the inward bowl-shape for dozens of laser durations.This special distribution of the longitudinal electrostatic field can simultaneously accelerate and converge the protons.Our particle-in-cell(PIC)simulation shows that the efficient proton acceleration can be realized with the Laguerre–Gaussian laser intensity ranging from 3.9×10^(21)W·cm^(-2)–1.6×10^(22)W·cm^(-2)available in the near future,e.g.,a quasi-monoenergetic proton beam with peak energy~115 MeV and divergence angles less than 5°can be generated by a 5.3×10^(21)W·cm^(-2)pulse.This work could provide a reference for the high-quality ion beam generation with PWclass laser systems available recently.

The(1+1)-dimensional nonlinear ion acoustic waves in multicomponent plasma containing kappa electrons

Large amplitude (1+1)-dimensional nonlinear ion acoustic waves are theoretically studied in multicomponent plasma consisting of positively charged ions and negatively charged ions, ion beam, kappa-distributed electrons, and dust grains,respectively. By using the Sagdeev potential method, the dynamical system and the Sagdeev potential function are obtained.The important influences of system parameters on the phase diagram of this system are investigated. It is found that the linear waves, the nonlinear waves and the solitary waves are coexistent in the multicomponent plasma system. Meanwhile,the variations of Sagdeev potential with parameter can also be obtained. Finally, it seems that the propagating characteristics of (1+1)-dimensional nonlinear ion acoustic solitary waves and ion acoustic nonlinear shock wave can be influenced by different parameters of this system.

Extreme ultraviolet spectral characteristic analysis of highly charged ions in laserproduced Cu plasmas

This paper reports the results of spectral measurements and a theoretical analysis of the temporal and spatial evolution of laser-produced Cu plasma in vacuum in the range of 8–14 nm.The time dependence of the extreme ultraviolet band spectrum at different positions near the target surface was obtained and found to be dominated by three broad-band features.The 3p and 3d excitations of Cu5+–Cu9+ions were calculated using the Hartree–Fock theory with configuration interactions.The characteristics of the spectral line distribution for the 3p–nd and 3d–nf transition arrays were analyzed.Based on the steady-state collisional radiation model and the normalized Boltzmann distribution,the complex spectral structure in the band of 13–14 nm is accurately explained through consistency comparisons and benchmarking between the experimental and theoretical simulation spectra,demonstrating that the structure mainly stems from the overlapping contribution of the 3d–4f and 3p–3d transition arrays for the Cu5+–Cu9+ions.These results may help in studying the radiation characteristics of isoelectronic series highly-charged ions involving the 3d excitation process.

Influence of extraction voltage on electron and ion behavior characteristics

The characteristics of the extracted ion current have a significant impact on the design and testing of ion source performance.In this paper,a 2D in space and 3D in velocity space particle in cell(2D3V PIC)method is utilized to simulate plasma motion and ion extraction characteristics under various initial plasma velocity distributions and extraction voltages in a Cartesian coordinate system.The plasma density is of the order of 10^(15)m^(-3)-10^(16)m^(-3)and the extraction voltage is of the order of 100 V-1000 V.The study investigates the impact of various extraction voltages on the velocity and density distributions of electrons and positive ions,and analyzes the influence of different initial plasma velocity distributions on the extraction current.The simulation results reveal that the main reason for the variation of extraction current is the spacecharge force formed by the relative aggregation of positive and negative net charges.This lays the foundation for a deeper understanding of extraction beam characteristics.

The tri-band high spectral resolution spectrometer with gratings in tandem for the charge-exchange recombination spectroscopy diagnostic system on HL-2A tokamak

Charge-exchange(CX) recombination spectroscopy is a powerful tool monitoring ion temperature and plasma rotation with good temporal and spatial resolutions. A compact, new design for a high-throughput, tri-band high spectral resolution spectrometer has been developed for the charge-exchange recombination spectroscopy measurement on the HL-2A tokamak. The simultaneous measurements of He II(468.57 nm), C VI(529.1 nm), and Dα(656.1 nm accompanied by beam emission spectra) with an acquisition frequency up to 400 Hz are achieved by vertically binning the spectrum from each fiber in experiments. Initial results indicate that the system can provide radial profiles of not only ion temperature and rotation velocity,but also concentration of carbon. For the case of helium, the measurements for the ion temperature and rotation velocity are straightforward but the apparent concentration associated with the observed CX intensity is obviously too high. Modeling of the active He II CX feature including plume contributions needs to be carried out to extract the true helium concentration.The spectrometer could become a prototype for the ITER charge-exchange recombination spectroscopy diagnostic and the pilot experiments, as presented here, demonstrate the possibility of impurity concentrations measurements based on the combined measurement of local beam emission and charge-exchange recombination spectroscopy spectra.

Power transfer efficiency in an air-breathing radio frequency ion thruster

Due to a series of challenges such as low-orbit maintenance of satellites, the air-breathing electric propulsion has got widespread attention. Commonly, the radio frequency ion thruster is favored by low-orbit missions due to its high specific impulse and efficiency. In this paper, the power transfer efficiency of the radio frequency ion thruster with different gas compositions is studied experimentally, which is obtained by measuring the radio frequency power and current of the antenna coil with and without discharge operation. The results show that increasing the turns of antenna coils can effectively improve the radio frequency power transfer efficiency, which is due to the improvement of Q factor. In pure N_2 discharge,with the increase of radio frequency power, the radio frequency power transfer efficiency first rises rapidly and then exhibits a less steep increasing trend. The radio frequency power transfer efficiency increases with the increase of gas pressure at relatively high power, while declines rapidly at relatively low power. In N_(2)/O_(2) discharge, increasing the N_(2) content at high power can improve the radio frequency power transfer efficiency, but the opposite was observed at low power. In order to give a better understanding of these trends, an analytic solution in limit cases is utilized, and a Langmuir probe was employed to measure the electron density. It is found that the evolution of radio frequency power transfer efficiency can be well explained by the variation of plasma resistance, which is related to the electron density and the effective electron collision frequency.

Effects of power on ion behaviors in radio-frequency magnetron sputtering of indium tin oxide(ITO)

This study delves into ion behavior at the substrate position within RF magnetron discharges utilizing an indium tin oxide(ITO)target.The positive ion energies exhibit an upward trajectory with increasing RF power,attributed to heightened plasma potential and initial emergent energy.Simultaneously,the positive ion flux escalates owing to amplified sputtering rates and electron density.Conversely,negative ions exhibit broad ion energy distribution functions(IEDFs)characterized by multiple peaks.These patterns are clarified by a combination of radiofrequency oscillation of cathode voltage and plasma potential,alongside ion transport time.This elucidation finds validation in a one-dimensional model encompassing the initial ion energy.At higher RF power,negative ions surpassing 100 e V escalate in both flux and energy,posing a potential risk of sputtering damages to ITO layers.

ION HEATING PROCESS DURING PLASMA IMMERSION ION IMPLANTATION

The research on plasma immersion ion implantation has been conducted for a little over ten years. Much is needed to investigate including processing technlogy, plasma sheath dynamics, interaction of plasma and surface, etc. Of the processing methods elavated temperature technique is usually used in PIII to produce a thick modified layer by means of the thermal diffusion. Meanwhile plasma ion heating is more recently developed by Ronghua Wei et al[1]. Therefore the temeperature is a critical parameter in plasma ion processing. In this paper we present the theoretical model and analysize the effect of imlantation voltage, plasma density, ion mass,etc on the temperature rise.

Tribological behavior of different films on Ti-6Al-4V alloy prepared by plasma-based ion implantation

The tribological behaviors of TiN coating and TiN+TiC+Ti(C, N)/diamond like carbon (DLC), TiN/DLC, TiC/DLC multilayers on Ti 6Al 4V alloy prepared by plasma based ion implantation (PBII) were compared. Under the test conditions of counterbody AISI 52100, load 1 N and speed 0.05 m/s, the tribological properties of the alloy are improved by these films in the order of TiN, TiC/DLC, TiN/DLC and TiN+TiC+Ti(C,N)/DLC. Tribological behavior is affected by the conditions of surface modification and triboexperiments. The appearance of “peaks” in the wear dynamic resistance profiles may be due or correspond to the process of formation and breaking apart of transition films. The breakthrough of the DLC coated samples may start from partially wearing out, and end with joining piece dilamination. There are transition films on all counterbodies AISI 52100. When AISI 52100 counterbody is changed to Ti 6Al 4V, the wear of most modified samples is changed from only disc to both disc and ball abrasive dominated.

Experimental Study of the Influence of Process Pressure and Gas Composition on GaAs Etching Characteristics in Cl_2/BCl_3-Based Inductively Coupled Plasma

A study of Cl2/BCl3-based inductively coupled plasma （ICP） was conducted using thick photoresist mask for anisotropic etching of 50μm diameter holes in a GaAs wafer at a relatively high average etching rate for etching depths of more than 150μm. Plasma etch characteristics with ICP process pressure and the percentage of BCI3 were studied in greater detail at a constant ICP coil/bias power. The measured peak-to-peak voltage as a function of pressure was used to estimate the minimum energy of the ions bombarding the substrate. The process pressure was found to have a substantial influence on the energy of heavy ions. Various ion species in plasma showed minimum energy variation from 1.85 eV to 7.5 eV in the pressure range of 20 mTorr to 50 mTorr. The effect of pressure and the percentage of BCl3 on the etching rate and surface smoothness of the bottom surface of the etched hole were studied for a fixed total flow rate. The etching rate was found to decrease with the percentage of BCl3, whereas the addition of BCl3 resulted in anisotropic holes with a smooth veil free bottom surface at a pressure of 30 mTorr and 42% BC13. In addition, variation of the etching yield with pressure and etching depth were also investigated.

TWO-DIMENSIONAL NUMERICAL ANALYSIS OF PLASMA IMMERSION ION IMPLANTATION OF CYLINDRICAL BORES

Plasma immersion ion implantation (PIII), unrestricted by sight-light process, is considered a proper method for inner surface strengthening. Two-dimensional simulation oj inner surface PIII process of cylindrical bores were carried out in this paper using cold plasma fluid model, and influence of the bore's dimension on impact energy, retained dose and uniformity of inner surface were investigated.

COMPUTATIONAL SCHEME FOR SIMULATING PLASMA DYNAM-ICS DURING PLASMA-IMMERSION ION IMPLANTATION

Plasma-immersion ion implantation (PIII) is a technique for implanting ions into conducting, semiconducting and insulating objects. In PIII, the object being treated is immersed in a plasma and pulsed to a large negative voltage (=-1 to-100 kV). The resulting sheath expands into the ambient plasma, extracting ions and accelerating them to the target. PIII has advantages over beam-line implantation in that large surfaces can be rapidly implanted, irregularly-shaped objects can be implanted without target manipulation, and surfaces that are not line-of-sight accessible can be treated. A two-dimensional, self-consistent model of plasma dynamics appropriate for PIII is described. The model is a hybrid, with Boltzmann electrons and kinetic ions, where the ion Vlasov equation is solved using the particle-in-cell (PIC) method. Solutions of the model give the time dependence of the ion flux, energy and impact angle at the target surface, together with the evolution of the sheath.

Spectrum Simulation of Li-Like Aluminium Plasma

X-ray emission spectra for L-shell of Li-like aluminium ions are simulated by using the flexible atomic code based on the collisional radiative model. Atomic processes including radiative recombination, dielectronic recombination, collisional ionization and resonance excitation from the neighbouring ion （Al^9＋ and Al^11＋ ） charge states of the target ion （Al^10＋） are considered in the model. In addition, the contributions of different atomic processes to the x-ray spectrum are analysed. The results show that dielectronic recombination, radiative recombination, collisional ionization and resonance excitation, other than direct collisional excitation, are very important processes.

COMPARISON OF SURFACE PROPERTIES OF Ti-6Al-4V COATED WITH TITANIUM NITRIDE, TiN+TiC+Ti(C,N)/DLC, TiN/DLC AND TiC/DLC FILMS BY PLASMA-BASED ION IMPLANTATION

The surface properties of Ti-6Al-4V alloy coated with titanium nitride, TiN+TiC+Ti(C,N)/DLC (diamond like carbon), TiN/DLC and TiC/DLC films by plasma-based ion implantation (PBII) with nitrogen, PBII with nitrogen then acetylene, PBII with nitrogen then glow discharge deposition with acetylene plus hydrogen and PBII with acetylene then glow discharge deposition with acetylene plus hydrogen respectively were studied. The corresponding films are found getting dimmer, showing light gold or gold, smoky color (uneven), light red in black (uneven), and graphite black separately. The corresponding film resistivities are given. Antioxidation ability of the titanium nitride film is poor, while the existence of carbon (or carbide) improves the antioxidation ability of the films. Having undergone excellent intermediate transitional region of nitrogen and carbon implantation, the top DLC layer of the TiN+TiC+Ti(C,N)/DLC multilayer are formed after the carbon implantation has the best adhesion with the substrate among all the multilayers. Although microhardness of the samples increases in the order of coatings of titanium nitride, TiN/DLC, TiN+TiC+Ti(C,N)/DLC and TiC/DLC, the TiN/DLC and TiC/DLC multilayers have greater brittleness as compared with other films.

PIC simulation of plasma properties in the discharge channel of a pulsed plasma thruster with flared electrodes

Plasma in the discharge channel of a pulsed plasma thruster(PPT) with flared electrodes is simulated by a self-developed two-dimensional code. The fully particle-in-cell method with Monte Carlo collision is employed to model the particle movement and collisions and investigate the plasma properties and acceleration process. Temporal and spatial variations of the electron density distribution and the ion velocity between electrodes are calculated and analyzed in detail.The computational results of the electron number density, which is in the order of 1023 m-3,show good agreements with experimental results of a PPT named ADD SIMP-LEX. The ion velocity distributions along the center line of the channel lead to a comprehensive understanding of ions accelerated by electromagnetic field. The electron distributions of PPT with discharge voltages varying from 1300 to 2000 V are compared. The diffusion of electrons presents strong dependency on discharge voltage and implies higher degree of ionization for higher voltage.

Ion Density Distribution in an Inductively Coupled Plasma Chamber

The ion density distribution in the reaction chamber was diagnosed by a Langmuir probe. The rules of the ion density distribution were obtained under the pressures of 9 Pa, 13 Pa, 27 Pa and 53 Pa in the reaction chamber, different radio-frequency powers and different positions. The result indicates that the ion density decreases as the pressure increases, and increases as the power decreases. The ion density of axial position z =0 achieves 5.8×1010 on the center of coil under the power of 200 w and pressure of 9 Pa in the reaction chamber.

Readout electronics of a prototype time-of-flight ion composition analyzer for space plasma

Readout electronics is developed for a prototype time-of-flight(TOF) ion composition spectrometer for in situ measurement of the mass/charge distributions of major ion species from 200 to 100 ke V/e in space plasma.By utilizing a constant fraction discriminator(CFD) and time-to-digital converter(TDC), challenging dynamic range measurements were performed with high time resolution and event rates. CFD was employed to discriminate the TOF signals from the micro-channel plate and channel electron multipliers. TDC based on the combination of counter and OR-gate delay chain was designed in a highreliability flash field programmable gate array. Owing to the non-uniformity of the delay chain, a correction algorithm based on integral nonlinearity compensation was implemented to reduce the time uncertainty. The test results showed that the electronics achieved a low timingerror of < 200 ps in the input range from 35 to 500 m V for the CFD, and a time resolution of ～550 ps with time uncertainty < 180 ps after correction and a time range of6.4 ls for the TDC. The TOF spectrum from an electron beam experiment of the impacting N_2 gas further indicated the good performance of this readout electronic.

Influence of chloride ion concentration on immersion corrosion behaviour of plasma sprayed alumina coatings on AZ31B magnesium alloy

Corrosion attack of aluminium and magnesium based alloys is a major issue worldwide.The corrosion degradation of an uncoated and atmospheric plasma sprayed alumina(APS)coatings on AZ31B magnesium alloy was investigated using immersion corrosion test in NaCl solutions of different chloride ion concentrations viz.,0.01 M,0.2 M,0.6 M and 1 M.The corroded surface was characterized by an optical microscope and X-ray diffraction.The results showed that the corrosion deterioration of uncoated and coated samples were significantly influenced by chloride ion concentration.The uncoated magnesium and alumina coatings were found to offer a superior corrosion resistance in lower chloride ion concentration NaCl solutions(0.01 M and 0.2 M NaCl).On the other hand the coatings and Mg alloy substrate were found to be highly susceptible to localized damage,and could not provide an effective corrosion protection in solutions containing higher chloride concentrations(0.6 M and 1 M).It was found that the corrosion resistance of the ceramic coatings and base metal gets deteriorated with the increase in the chloride concentrations.